The equilibrium adsorption isotherm and kinetic of the sorption process for W and Mo on macro chelating resin D403 were investigated on single Na2 Mo O4 and Na2WO4 solutions.The sorption isotherm results show that the...The equilibrium adsorption isotherm and kinetic of the sorption process for W and Mo on macro chelating resin D403 were investigated on single Na2 Mo O4 and Na2WO4 solutions.The sorption isotherm results show that the adsorption process of W obeys the Freundlich model very well whereas the exchange process with Mo approximately follows the Henry model.The kinetic experiments show that the intraparticle diffusion process was the rate-determining step for W sorption on the resin,and the corresponding activation energy is calculated to be 21.976 k J/mol.展开更多
A toughener that can effectively improve the interlaminar toughness in carbon fiber composites is crucial for various applications.We investigated,the toughening effects of phenolphthalein-based cardo poly(ether sulfo...A toughener that can effectively improve the interlaminar toughness in carbon fiber composites is crucial for various applications.We investigated,the toughening effects of phenolphthalein-based cardo poly(ether sulfone)(PES-C)on E51/DETDA epoxy and its carbon fiber composites(CFCs).Scanning electron microscopy showed that the phase structures of PES-C/epoxy blends change from island(of dispersed phase)structures to bi-continuous structures(of the matrix)as the PES-C content increased,which is associated with reaction-induced phase separation.After adding 15 phr PES-C,the glass transition temperature(T_(g))of the blends increased by 51.5℃,and the flexural strength,impact strength and fracture toughness of the blends were improved by 41.1%,186.2%and 42.7%,respectively.These improvements could be attributed to the phase separation structure of the PES-C/epoxy sys-tem.A PES-C film was used to improve the mode-II fracture toughness(G_(IIC))of CFCs.The G_(IIC) value of the 7μm PES-C film toughened laminate was improved by 80.3%compared to that of the control laminate.The increase in G_(IIC) was attributed to cohesive failure and plastic deformation in the interleaving region.展开更多
To improve the purity of the total phloroglucinols from Dryopteris crassirhizoma extracts, the separation and purification conditions of the total phloroglucinols from Dryopteris crassirhizoma were studied with DM-130...To improve the purity of the total phloroglucinols from Dryopteris crassirhizoma extracts, the separation and purification conditions of the total phloroglucinols from Dryopteris crassirhizoma were studied with DM-130 macroporous adsorption resin in this study. Adsorption rate, elution rate and purity of the total phloroglucinols were used as indexes to investigate the adsorption and desorption capacity of the total phloroglucinols with DM-130 macroporous adsorption resin. Through the study, the optimum sample concentration of the total phloroglucinols and maximum sample volume were 1.5 mg·mL^-1 and 7 BV （210 mL）, respectively. The optimum desorption conditions were achieved by using 80% ethanol as desorption solvent at elution flow rate of 1.0 mL·min^-1. The result showed DM-130 macroporous adsorption resin performed effective adsorption and desorption. After purification, the purity of the total phloroglucinols increased by 11.5-fold.展开更多
A novel alkoxycarbonyl thiourea resin(ATR)was synthesized by monomer polymerization of oxydiethane-2,1-diyl dicarbonisothiocyanatidate and polyethylene polyamine,and characterized by FT-IR.The adsorption properties of...A novel alkoxycarbonyl thiourea resin(ATR)was synthesized by monomer polymerization of oxydiethane-2,1-diyl dicarbonisothiocyanatidate and polyethylene polyamine,and characterized by FT-IR.The adsorption properties of ATR were investigated by batch test.The adsorption capacities for Au(Ⅲ),Ag(Ⅰ),Cu(Ⅱ),Zn(Ⅱ),Fe(Ⅲ),Ca(Ⅱ)and Mg(Ⅱ)are 4.65,4.40,0.40,0.90,0.86,0.0080 and 0.016 mmol/g,respectively,when the adsorption condition is as follows:contact time 24 h,temperature 30℃,initial concentration of Au(Ⅲ)5.08 mmol/L and that of other metals 0.10 mol/L,and concentration of acid 1.0 mol/L.The adsorption capacity for Au(Ⅲ)increases with the increase of contact time,temperature and initial concentration of Au(Ⅲ).The capacity after five adsorption-desorption cycles remains 90%that of the first time,and the separation factors of ATR for binary metal ion solutions are larger than 995,indicating that ATR is of good regeneration property and selectivity.XPS results show that the functional atoms of ATR supply electrons for Au and coordinate with Au during the adsorption.展开更多
Diglycidyl 4,5-epoxy tetrahydro phthalate/methyl tetrahydrophthalic anhydride （TDE-85/MeTHPA） epoxy resin modified by polyurethane （PU） was prepared with 1,4-butanediol （1,4-BDO）, trimethylol propane （TMP） and...Diglycidyl 4,5-epoxy tetrahydro phthalate/methyl tetrahydrophthalic anhydride （TDE-85/MeTHPA） epoxy resin modified by polyurethane （PU） was prepared with 1,4-butanediol （1,4-BDO）, trimethylol propane （TMP） and polyurethane prepolymer synthesized by polypropylene glycol and toluene diisocynate. Chemical reaction and curing mechanism of this system were discussed by incorporating the results of infra spectrum analysis. The results indicate that the epoxy polymeric network I is obtained by the curing reaction between TDE-85 and MeTHPA, while the PU polymeric network II is obtained by the chain-extended and crosslinking reaction between 1,4-BDO, TMP and polyurethane prepolymer（PUP）. The graft chemical bonds are formed between polymer networks I and II that therefore increase the degree of blend and compatibility between epoxy polymer and PU.展开更多
The adsorption properties of a novel macroporous weak acid resin （D152） for Pb^2＋ were investigated with chemical methods. The optimal adsorption condition of D152 resin for Pb^2＋ is at pH 6.00 in HAc-NaAc medium....The adsorption properties of a novel macroporous weak acid resin （D152） for Pb^2＋ were investigated with chemical methods. The optimal adsorption condition of D152 resin for Pb^2＋ is at pH 6.00 in HAc-NaAc medium. The statically saturated adsorption capacity is 527 mg/g at 298 K. Pb^2＋ adsorbed on D152 resin can be eluted with 0.05 mol/L HCI quantitatively. The adsorption rate constants determined under various temperatures are k288 n=2.22×10-5 s^-1, k298 K=2.51 × 10^-5 s^-1, and k308 K= 2.95 × 10^-5 s^-1, respectively. The apparent activation energy, Ea is 10.5 kJ/mol, and the adsorption parameters of thermodynamics are ΔH^Θ=13.3 kJ/mol, ΔS^Θ=119 J/（mol·K）, and ΔG^Θ298 K =-22.2 kJ/mol, respectively. The adsorption behavior of D152 resin for Pb^2＋ follows Langmuir model.展开更多
A novel chelating resin with sulfonic group was synthesized by chemical modification of D401 resin with sulphonation reaction and characterized by FT-IR spectrometry. The adsorption properties of the novel chelating r...A novel chelating resin with sulfonic group was synthesized by chemical modification of D401 resin with sulphonation reaction and characterized by FT-IR spectrometry. The adsorption properties of the novel chelating resin for Pb2+ were studied by batch adsorption, and the adsorption process was analyzed from thermodynamics and kinetics aspects. The adsorption mechanism of Pb2+ on the modified D401 chelating resin was discussed by FT-IR spectrometry. Experimental results show that in the Pb2+ concentration range of 200-400 mg/L, the adsorption capacities of the modified D401 chelating resin for Pb2+ increase by 77%-129%, and Langmuir isothermal adsorption model is more suitable for the equilibrium adsorption data. Adsorption is an endothermic process that runs spontaneously. Kinetic analysis shows that the adsorption rate is mainly governed by liquid film diffusion. The best pH value under adsorption condition is 4-5. The saturated resin can be regenerated by 3 mol/L nitric acid, and the adsorption capacity remains stable after five consecutive adsorption-desorption cycles. The maximal static saturated adsorption capacity of the resin is 206 mg/g at 333 K in the Pb2+ concentration range of 200-400 mg/L. The modified D401 chelating resin is an efficient adsorbent for the removal of Pb2+ from its single-metal ion solution.展开更多
Urea-isobutyraldehyde-formaldehyde (UIF) resin was synthesized from urea, isobutyraldehyde, and formaldehyde using sulfuric acid as a catalyst by one pot method. The effects of molar ratios of isobutyraldehyde to form...Urea-isobutyraldehyde-formaldehyde (UIF) resin was synthesized from urea, isobutyraldehyde, and formaldehyde using sulfuric acid as a catalyst by one pot method. The effects of molar ratios of isobutyraldehyde to formaldehyde (n(I)/n(F)) and aldehyde to urea (n(A)/n(U)) on the yield, hydroxyl value (vs KOH) and softening point of the resin were investigated. The structure of the resin was characterized by FT-IR, 1H-NMR and 13C-NMR. The results show that when the molar ratio of urea to isobutyraldehyde to formaldehyde (n(U)/n(I)/n(F)) is 1.0/3.0/3.0, the yield UIF resin is 67.1%, and the softening point and hydroxyl value are 88 ℃ and 37 mg/g, respectively. The FT-IR, 1H-NMR and 13C-NMR results show that the lactam is formed by aminomethylation from urea, isobutyraldehyde, and formaldehyde.展开更多
This study presents the deep removal of copper (Ⅱ) from the simulated cobalt electrolyte using fabricated polystyrene-supported 2-aminomethylpyridine chelating resin (PS-AMP) in a fixed-bed.The effects of bed height ...This study presents the deep removal of copper (Ⅱ) from the simulated cobalt electrolyte using fabricated polystyrene-supported 2-aminomethylpyridine chelating resin (PS-AMP) in a fixed-bed.The effects of bed height (7.0–14.0 cm),feed flow rate (4.5–9.0 mL/min),initial copper (Ⅱ) concentration of the feed (250–1000 mg/L),feed temperature (25–40 ℃) and the value of pH (2.0–4.0) on the adsorption process of the PS-AMP resin were investigated.The experimental data showed that the PS-AMP resin can deeply eliminate copper (Ⅱ) from the simulated cobalt electrolyte.The bed height,feed flow rate,initial copper (Ⅱ) concentration of the feed,feed temperature and feed pH value which corresponded to the highest removal of copper (Ⅱ) were 7.0 cm with 35 mm of the column diameter,4.5 mL/min,40℃,1000 mg/L and 4.0,respectively.The breakthrough capacity,the saturated capacity of the column and the mass ratio of Cu/Co (g/g) in the saturated resin were correspondingly 16.51 mg/g dry resin,61.72 mg/g dry resin and 37.67 under the optimal experimental conditions.The copper (Ⅱ) breakthrough curves were fitted by the empirical models of Thomas,Yoon-Nelson and Adam-Bohart,respectively.The Thomas model was found to be the most suitable one for predicting how the concentration of copper (Ⅱ) in the effluent changes with the adsorption time.展开更多
Diglycidyl-4,5-epoxycyclohexane-1,2-dicarboxylate(TDE-85)/methyl tetrahydrophthalic anhydride (MeTHPA) epoxy resin was modified with polyurethane(PU) and the interpenetrating polymer networks(IPNs) of PU-modified TDE-...Diglycidyl-4,5-epoxycyclohexane-1,2-dicarboxylate(TDE-85)/methyl tetrahydrophthalic anhydride (MeTHPA) epoxy resin was modified with polyurethane(PU) and the interpenetrating polymer networks(IPNs) of PU-modified TDE-85/MeTHPA resin were prepared. The structural characteristics and properties of PU-modified TDE-85/MeTHPA resin were investigated by Fourier transform infrared(FTIR) spectrum,emission scanning electron microscopy(SEM) and thermogravimetry(TG). The results indicate that epoxy polymer network (Ⅰ) and polyurethane polymer network (Ⅱ) of the modified resin can be obtained and the networks (Ⅰ) and (Ⅱ) interpenetrate and tangle highly each other at the phase interface. The micro morphology presents heterogeneous structure. The integrative properties of PU-modified TDE-85/MeTHPA epoxy resin are improved obviously. The PU-modified TDE-85/ MeTHPA resin's tensile strength reaches 69.39 MPa,the impact strength reaches 23.56 kJ/m,the temperature for the system to lose 1% mass (t1%) is 300 ℃,and that for the system to lose 50% mass (t50%) is 378 ℃. Compared with those of TDE-85/MeTHPA resin,the tensile strength,impact strength,t1% and t50% of the PU-modified resin increases by 48%,115%,30 ℃,11 ℃,respectively. The PU-modified TDE-85/MeTHPA resin has the structure characteristics and properties of interpenetrating polymer networks.展开更多
PS-PAMAM-IDA chelating resins were prepared by low-generations of polyamidoamine(PAMAM) and then chloroacetic acid functionalizing commercially available ammoniated polystyrene matrix, to preconcentrate Ni2+ from synt...PS-PAMAM-IDA chelating resins were prepared by low-generations of polyamidoamine(PAMAM) and then chloroacetic acid functionalizing commercially available ammoniated polystyrene matrix, to preconcentrate Ni2+ from synthetic aqueous samples. Different generations of PAMAM were used to obtain different chelating resins, PS-IDA, PS-1.0G PAMAM-IDA and PS-2.0G PAMAM-IDA. The synthesized resins were characterized by FTIR and elemental analysis. The effect of solution pH, kinetic studies, resin loading capacity, matrix effects etc., on metal ion adsorption to adsorbent phase, were studied by batch method. The PS-1.0G PAMAM-IDA resin was the most excellent adsorbents, with a maximum adsorption capacity of(24.09±1.79) mg/g for Ni2+ ion at pH=7. The interpretation of the equilibrium data was given by Langmuir isotherms model, and the correlation coefficient values for PS-IDA, PS-1.0G PAMAM-IDA and PS-2.0G PAMAM-IDA resins were 0.992, 0.994 and 0.987, respectively.展开更多
The effectiveness of a magnetic ion exchange resin （MIEX） for the treatment of Hongze Lake water in China was evaluated, The kinetics of natural organic matter （NOM） removal at various MIEX doses and contact time,...The effectiveness of a magnetic ion exchange resin （MIEX） for the treatment of Hongze Lake water in China was evaluated, The kinetics of natural organic matter （NOM） removal at various MIEX doses and contact time, multiple-loading experiments, impacts of MIEX prior to coagulation on coagulant demands and the effectiveness of combination of MIEX, pre-chlorination and coagulation were investigated. Kinetic experimental results show that more than 80% UV254 and 67% dissolved organic carbon （DOC） from raw water can be removed by the use of MIEX alone. 94% sulfate, 69% nitrate and 98% bromide removals are obtained after the first use of MIEX in multiple-loading experiments. It is suggested that MIEX can be loaded up to 1 250 bed volume （BV, volume ratio of tested water to resin） or more without saturation when regarding organics removal as a target. MIEX can remove organics to a greater extend than coagulation and lower the coagulant demand when combining with coagulation. Chlorination experimental results show that MIEX can remove 57% chlorine demand and 77% trihalomethane formation potential （THMFP） for raw water. Pre-chlorination followed by MIEX and coagulation can give additional organic and THMFP removals. The results suggest that MIEX provides a new method to solve thc problem algae reproduction.展开更多
Pyrolytic resin carbon anode for lithoum ion batteries was prepared from thermosetting phenolic resin. Pyrolysis of the primary phenolic resin and the dewatered one was studied by thermal gravimetric analysis. Structu...Pyrolytic resin carbon anode for lithoum ion batteries was prepared from thermosetting phenolic resin. Pyrolysis of the primary phenolic resin and the dewatered one was studied by thermal gravimetric analysis. Structures and characteristics of the carbon materials were determined by X-ray diffraction, Brunauer-Emmer-Teller surface area analysis and electrochemical measurements. With the increase of pyrolyzing temperature and soaking time, the resin carbon material has larger crystallite sizes of L_c and L_a, lower specific surface area, smaller irreversible capacity and higher initial coulombic efficiency. The pyrolyzing temperature and soaking time are optimized to be 1050℃ and 2h. The resin carbon anode obtained under the optimum conditions shows good electrochemical performances with reversible capacity of 387mA·h/g and initial coulombic efficiency of 69.1%.展开更多
The adsorption capability of D318 resin for Cr（Ⅵ） was investigated by chemistry analysis. Experimental results show that D318 resin has the best adsorption ability for Cr（Ⅵ） at pH=3.16 in HAc-NaAc medium. The st...The adsorption capability of D318 resin for Cr（Ⅵ） was investigated by chemistry analysis. Experimental results show that D318 resin has the best adsorption ability for Cr（Ⅵ） at pH=3.16 in HAc-NaAc medium. The statically saturated adsorption capacity of the resin is 265.4 mg/g. The thermodynamic adsorption parameters, enthalpy change AH and free energy change AG298 of the adsorption reaction are 4.81 and -5.16 kJ/mol, respectively. The apparent activation energy Ea is 22.4 kJ/mol. The adsorption behavior obeys the Freundlich isotherm. The molar coordination ratio of the functional group of resin to Cr（Ⅵ） is 3：2. Cr（Ⅵ） adsorbed on D318 resin can be eluted by 5%NaOH-5%NaCl quantitatively.展开更多
Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flak...Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flake graphite powders that were evenly loaded with tungsten copper composite powder(RMCBCs-W@Cu)exhibited a low wear rate of 1.63 mm^(3)/h,exhibiting 48.6%reduction in the wear rate relative to RCMBCs without additives(RMCBCs-0).In addition,RMCBCs-W@Cu achieved a low friction coefficient of 0.243 and low electric spark grade.These findings indicate that tungsten copper composite powders provide particle reinforcement and generate a gradation effect for the epoxy resin(i.e.,connecting phase)in RMCBCs,which weakens the wear of RMCBCs caused by fatigue under a cyclic current-carrying wear.展开更多
A novel polyamide 6/silica nanocomposite containing epoxy resins(EPA6N) was prepared via in situ polymerization using tetraethoxysilane(TEOS) as the precursor of silica.The dynamic rheological properties of pure PA6 a...A novel polyamide 6/silica nanocomposite containing epoxy resins(EPA6N) was prepared via in situ polymerization using tetraethoxysilane(TEOS) as the precursor of silica.The dynamic rheological properties of pure PA6 and EPA6N at temperatures of 225 and 235 ℃ were investigated.The results of transmission electron microscopy(TEM) and atomic force microscopy(AFM) indicate that the silica particles are well dispersed in the polyamide 6 matrix on about 30 nm in diameter,which demonstrates that this method can effectively avoid agglomeration of the inorganic particles.The rheological results suggest that pure PA6 shows Newtonian behavior.However,the novel EPA6N exhibits a solid-like rheological behavior,which is due to the small size,large surface of silica particles and the stronger polyamide 6-silica chemical bond formed through the reactions of epoxy resins with end groups of PA6 molecular chains.The EPA6N also exhibits higher melt viscosity,storage modulus and loss modulus than those of pure PA6.展开更多
基金Project (2014CB643405) supported by National Research Development Program of China
文摘The equilibrium adsorption isotherm and kinetic of the sorption process for W and Mo on macro chelating resin D403 were investigated on single Na2 Mo O4 and Na2WO4 solutions.The sorption isotherm results show that the adsorption process of W obeys the Freundlich model very well whereas the exchange process with Mo approximately follows the Henry model.The kinetic experiments show that the intraparticle diffusion process was the rate-determining step for W sorption on the resin,and the corresponding activation energy is calculated to be 21.976 k J/mol.
文摘A toughener that can effectively improve the interlaminar toughness in carbon fiber composites is crucial for various applications.We investigated,the toughening effects of phenolphthalein-based cardo poly(ether sulfone)(PES-C)on E51/DETDA epoxy and its carbon fiber composites(CFCs).Scanning electron microscopy showed that the phase structures of PES-C/epoxy blends change from island(of dispersed phase)structures to bi-continuous structures(of the matrix)as the PES-C content increased,which is associated with reaction-induced phase separation.After adding 15 phr PES-C,the glass transition temperature(T_(g))of the blends increased by 51.5℃,and the flexural strength,impact strength and fracture toughness of the blends were improved by 41.1%,186.2%and 42.7%,respectively.These improvements could be attributed to the phase separation structure of the PES-C/epoxy sys-tem.A PES-C film was used to improve the mode-II fracture toughness(G_(IIC))of CFCs.The G_(IIC) value of the 7μm PES-C film toughened laminate was improved by 80.3%compared to that of the control laminate.The increase in G_(IIC) was attributed to cohesive failure and plastic deformation in the interleaving region.
基金Supported by the National Natural Science Foundation of China(31070291)
文摘To improve the purity of the total phloroglucinols from Dryopteris crassirhizoma extracts, the separation and purification conditions of the total phloroglucinols from Dryopteris crassirhizoma were studied with DM-130 macroporous adsorption resin in this study. Adsorption rate, elution rate and purity of the total phloroglucinols were used as indexes to investigate the adsorption and desorption capacity of the total phloroglucinols with DM-130 macroporous adsorption resin. Through the study, the optimum sample concentration of the total phloroglucinols and maximum sample volume were 1.5 mg·mL^-1 and 7 BV （210 mL）, respectively. The optimum desorption conditions were achieved by using 80% ethanol as desorption solvent at elution flow rate of 1.0 mL·min^-1. The result showed DM-130 macroporous adsorption resin performed effective adsorption and desorption. After purification, the purity of the total phloroglucinols increased by 11.5-fold.
基金Projects(20476105,50604016)supported by the National Natural Science Foundation of China
文摘A novel alkoxycarbonyl thiourea resin(ATR)was synthesized by monomer polymerization of oxydiethane-2,1-diyl dicarbonisothiocyanatidate and polyethylene polyamine,and characterized by FT-IR.The adsorption properties of ATR were investigated by batch test.The adsorption capacities for Au(Ⅲ),Ag(Ⅰ),Cu(Ⅱ),Zn(Ⅱ),Fe(Ⅲ),Ca(Ⅱ)and Mg(Ⅱ)are 4.65,4.40,0.40,0.90,0.86,0.0080 and 0.016 mmol/g,respectively,when the adsorption condition is as follows:contact time 24 h,temperature 30℃,initial concentration of Au(Ⅲ)5.08 mmol/L and that of other metals 0.10 mol/L,and concentration of acid 1.0 mol/L.The adsorption capacity for Au(Ⅲ)increases with the increase of contact time,temperature and initial concentration of Au(Ⅲ).The capacity after five adsorption-desorption cycles remains 90%that of the first time,and the separation factors of ATR for binary metal ion solutions are larger than 995,indicating that ATR is of good regeneration property and selectivity.XPS results show that the functional atoms of ATR supply electrons for Au and coordinate with Au during the adsorption.
基金Project(2003AA84ts04) supported by the National High-Tech Research and Development Program of China
文摘Diglycidyl 4,5-epoxy tetrahydro phthalate/methyl tetrahydrophthalic anhydride （TDE-85/MeTHPA） epoxy resin modified by polyurethane （PU） was prepared with 1,4-butanediol （1,4-BDO）, trimethylol propane （TMP） and polyurethane prepolymer synthesized by polypropylene glycol and toluene diisocynate. Chemical reaction and curing mechanism of this system were discussed by incorporating the results of infra spectrum analysis. The results indicate that the epoxy polymeric network I is obtained by the curing reaction between TDE-85 and MeTHPA, while the PU polymeric network II is obtained by the chain-extended and crosslinking reaction between 1,4-BDO, TMP and polyurethane prepolymer（PUP）. The graft chemical bonds are formed between polymer networks I and II that therefore increase the degree of blend and compatibility between epoxy polymer and PU.
基金Project(2008F70059) supported by the Scientific and Technological Research Planning of Zhejiang Province, China
文摘The adsorption properties of a novel macroporous weak acid resin （D152） for Pb^2＋ were investigated with chemical methods. The optimal adsorption condition of D152 resin for Pb^2＋ is at pH 6.00 in HAc-NaAc medium. The statically saturated adsorption capacity is 527 mg/g at 298 K. Pb^2＋ adsorbed on D152 resin can be eluted with 0.05 mol/L HCI quantitatively. The adsorption rate constants determined under various temperatures are k288 n=2.22×10-5 s^-1, k298 K=2.51 × 10^-5 s^-1, and k308 K= 2.95 × 10^-5 s^-1, respectively. The apparent activation energy, Ea is 10.5 kJ/mol, and the adsorption parameters of thermodynamics are ΔH^Θ=13.3 kJ/mol, ΔS^Θ=119 J/（mol·K）, and ΔG^Θ298 K =-22.2 kJ/mol, respectively. The adsorption behavior of D152 resin for Pb^2＋ follows Langmuir model.
基金Project(708049) supported by the Important Item Cultivation Foundation of Scientific Innovation Project of Colleges and Universities of China
文摘A novel chelating resin with sulfonic group was synthesized by chemical modification of D401 resin with sulphonation reaction and characterized by FT-IR spectrometry. The adsorption properties of the novel chelating resin for Pb2+ were studied by batch adsorption, and the adsorption process was analyzed from thermodynamics and kinetics aspects. The adsorption mechanism of Pb2+ on the modified D401 chelating resin was discussed by FT-IR spectrometry. Experimental results show that in the Pb2+ concentration range of 200-400 mg/L, the adsorption capacities of the modified D401 chelating resin for Pb2+ increase by 77%-129%, and Langmuir isothermal adsorption model is more suitable for the equilibrium adsorption data. Adsorption is an endothermic process that runs spontaneously. Kinetic analysis shows that the adsorption rate is mainly governed by liquid film diffusion. The best pH value under adsorption condition is 4-5. The saturated resin can be regenerated by 3 mol/L nitric acid, and the adsorption capacity remains stable after five consecutive adsorption-desorption cycles. The maximal static saturated adsorption capacity of the resin is 206 mg/g at 333 K in the Pb2+ concentration range of 200-400 mg/L. The modified D401 chelating resin is an efficient adsorbent for the removal of Pb2+ from its single-metal ion solution.
基金Project(2006A10902001) supported by the Science and Technology Plan of Guangdong Province, ChinaProject(2007Z3-D0351) supported by the Science and Technology Plan of Guangzhou City, China
文摘Urea-isobutyraldehyde-formaldehyde (UIF) resin was synthesized from urea, isobutyraldehyde, and formaldehyde using sulfuric acid as a catalyst by one pot method. The effects of molar ratios of isobutyraldehyde to formaldehyde (n(I)/n(F)) and aldehyde to urea (n(A)/n(U)) on the yield, hydroxyl value (vs KOH) and softening point of the resin were investigated. The structure of the resin was characterized by FT-IR, 1H-NMR and 13C-NMR. The results show that when the molar ratio of urea to isobutyraldehyde to formaldehyde (n(U)/n(I)/n(F)) is 1.0/3.0/3.0, the yield UIF resin is 67.1%, and the softening point and hydroxyl value are 88 ℃ and 37 mg/g, respectively. The FT-IR, 1H-NMR and 13C-NMR results show that the lactam is formed by aminomethylation from urea, isobutyraldehyde, and formaldehyde.
基金Project(2014CB643401)supported by the National Basic Research Program of ChinaProjects(51134007,51474256)supported by the National Natural Science Foundation of ChinaProject(2017TP1001)supported by the Hunan Provincial Science and Technology Plan Project,China
文摘This study presents the deep removal of copper (Ⅱ) from the simulated cobalt electrolyte using fabricated polystyrene-supported 2-aminomethylpyridine chelating resin (PS-AMP) in a fixed-bed.The effects of bed height (7.0–14.0 cm),feed flow rate (4.5–9.0 mL/min),initial copper (Ⅱ) concentration of the feed (250–1000 mg/L),feed temperature (25–40 ℃) and the value of pH (2.0–4.0) on the adsorption process of the PS-AMP resin were investigated.The experimental data showed that the PS-AMP resin can deeply eliminate copper (Ⅱ) from the simulated cobalt electrolyte.The bed height,feed flow rate,initial copper (Ⅱ) concentration of the feed,feed temperature and feed pH value which corresponded to the highest removal of copper (Ⅱ) were 7.0 cm with 35 mm of the column diameter,4.5 mL/min,40℃,1000 mg/L and 4.0,respectively.The breakthrough capacity,the saturated capacity of the column and the mass ratio of Cu/Co (g/g) in the saturated resin were correspondingly 16.51 mg/g dry resin,61.72 mg/g dry resin and 37.67 under the optimal experimental conditions.The copper (Ⅱ) breakthrough curves were fitted by the empirical models of Thomas,Yoon-Nelson and Adam-Bohart,respectively.The Thomas model was found to be the most suitable one for predicting how the concentration of copper (Ⅱ) in the effluent changes with the adsorption time.
基金Project(2003AA84ts04) supported by the National High-Tech Research and Development Program of China
文摘Diglycidyl-4,5-epoxycyclohexane-1,2-dicarboxylate(TDE-85)/methyl tetrahydrophthalic anhydride (MeTHPA) epoxy resin was modified with polyurethane(PU) and the interpenetrating polymer networks(IPNs) of PU-modified TDE-85/MeTHPA resin were prepared. The structural characteristics and properties of PU-modified TDE-85/MeTHPA resin were investigated by Fourier transform infrared(FTIR) spectrum,emission scanning electron microscopy(SEM) and thermogravimetry(TG). The results indicate that epoxy polymer network (Ⅰ) and polyurethane polymer network (Ⅱ) of the modified resin can be obtained and the networks (Ⅰ) and (Ⅱ) interpenetrate and tangle highly each other at the phase interface. The micro morphology presents heterogeneous structure. The integrative properties of PU-modified TDE-85/MeTHPA epoxy resin are improved obviously. The PU-modified TDE-85/ MeTHPA resin's tensile strength reaches 69.39 MPa,the impact strength reaches 23.56 kJ/m,the temperature for the system to lose 1% mass (t1%) is 300 ℃,and that for the system to lose 50% mass (t50%) is 378 ℃. Compared with those of TDE-85/MeTHPA resin,the tensile strength,impact strength,t1% and t50% of the PU-modified resin increases by 48%,115%,30 ℃,11 ℃,respectively. The PU-modified TDE-85/MeTHPA resin has the structure characteristics and properties of interpenetrating polymer networks.
基金Project(51074192)supported by the National Natural Science Foundation of China
文摘PS-PAMAM-IDA chelating resins were prepared by low-generations of polyamidoamine(PAMAM) and then chloroacetic acid functionalizing commercially available ammoniated polystyrene matrix, to preconcentrate Ni2+ from synthetic aqueous samples. Different generations of PAMAM were used to obtain different chelating resins, PS-IDA, PS-1.0G PAMAM-IDA and PS-2.0G PAMAM-IDA. The synthesized resins were characterized by FTIR and elemental analysis. The effect of solution pH, kinetic studies, resin loading capacity, matrix effects etc., on metal ion adsorption to adsorbent phase, were studied by batch method. The PS-1.0G PAMAM-IDA resin was the most excellent adsorbents, with a maximum adsorption capacity of(24.09±1.79) mg/g for Ni2+ ion at pH=7. The interpretation of the equilibrium data was given by Langmuir isotherms model, and the correlation coefficient values for PS-IDA, PS-1.0G PAMAM-IDA and PS-2.0G PAMAM-IDA resins were 0.992, 0.994 and 0.987, respectively.
基金Project(2008ZX07421-002) supported by the Key National Science and Technology Project of ChinaProject(50638020) supported by the National Natural Science Foundation of China
文摘The effectiveness of a magnetic ion exchange resin （MIEX） for the treatment of Hongze Lake water in China was evaluated, The kinetics of natural organic matter （NOM） removal at various MIEX doses and contact time, multiple-loading experiments, impacts of MIEX prior to coagulation on coagulant demands and the effectiveness of combination of MIEX, pre-chlorination and coagulation were investigated. Kinetic experimental results show that more than 80% UV254 and 67% dissolved organic carbon （DOC） from raw water can be removed by the use of MIEX alone. 94% sulfate, 69% nitrate and 98% bromide removals are obtained after the first use of MIEX in multiple-loading experiments. It is suggested that MIEX can be loaded up to 1 250 bed volume （BV, volume ratio of tested water to resin） or more without saturation when regarding organics removal as a target. MIEX can remove organics to a greater extend than coagulation and lower the coagulant demand when combining with coagulation. Chlorination experimental results show that MIEX can remove 57% chlorine demand and 77% trihalomethane formation potential （THMFP） for raw water. Pre-chlorination followed by MIEX and coagulation can give additional organic and THMFP removals. The results suggest that MIEX provides a new method to solve thc problem algae reproduction.
文摘Pyrolytic resin carbon anode for lithoum ion batteries was prepared from thermosetting phenolic resin. Pyrolysis of the primary phenolic resin and the dewatered one was studied by thermal gravimetric analysis. Structures and characteristics of the carbon materials were determined by X-ray diffraction, Brunauer-Emmer-Teller surface area analysis and electrochemical measurements. With the increase of pyrolyzing temperature and soaking time, the resin carbon material has larger crystallite sizes of L_c and L_a, lower specific surface area, smaller irreversible capacity and higher initial coulombic efficiency. The pyrolyzing temperature and soaking time are optimized to be 1050℃ and 2h. The resin carbon anode obtained under the optimum conditions shows good electrochemical performances with reversible capacity of 387mA·h/g and initial coulombic efficiency of 69.1%.
基金Project (Y304121) supported by the Natural Science Foundation of Zhejiang Province,China
文摘The adsorption capability of D318 resin for Cr（Ⅵ） was investigated by chemistry analysis. Experimental results show that D318 resin has the best adsorption ability for Cr（Ⅵ） at pH=3.16 in HAc-NaAc medium. The statically saturated adsorption capacity of the resin is 265.4 mg/g. The thermodynamic adsorption parameters, enthalpy change AH and free energy change AG298 of the adsorption reaction are 4.81 and -5.16 kJ/mol, respectively. The apparent activation energy Ea is 22.4 kJ/mol. The adsorption behavior obeys the Freundlich isotherm. The molar coordination ratio of the functional group of resin to Cr（Ⅵ） is 3：2. Cr（Ⅵ） adsorbed on D318 resin can be eluted by 5%NaOH-5%NaCl quantitatively.
基金Projects(51772081,51837009,51971091)supported by the National Natural Science Foundation of ChinaProject(HFZL2018CXY003-4)supported by the Industry-University-Research Cooperation of AECC,ChinaProject(kq1902046)supported by the Major Science and Technology Projects of Changsha City,China。
文摘Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flake graphite powders that were evenly loaded with tungsten copper composite powder(RMCBCs-W@Cu)exhibited a low wear rate of 1.63 mm^(3)/h,exhibiting 48.6%reduction in the wear rate relative to RCMBCs without additives(RMCBCs-0).In addition,RMCBCs-W@Cu achieved a low friction coefficient of 0.243 and low electric spark grade.These findings indicate that tungsten copper composite powders provide particle reinforcement and generate a gradation effect for the epoxy resin(i.e.,connecting phase)in RMCBCs,which weakens the wear of RMCBCs caused by fatigue under a cyclic current-carrying wear.
基金Project(07A071) supported by the Scientific Research Foundation of Hunan Provincial Education Department
文摘A novel polyamide 6/silica nanocomposite containing epoxy resins(EPA6N) was prepared via in situ polymerization using tetraethoxysilane(TEOS) as the precursor of silica.The dynamic rheological properties of pure PA6 and EPA6N at temperatures of 225 and 235 ℃ were investigated.The results of transmission electron microscopy(TEM) and atomic force microscopy(AFM) indicate that the silica particles are well dispersed in the polyamide 6 matrix on about 30 nm in diameter,which demonstrates that this method can effectively avoid agglomeration of the inorganic particles.The rheological results suggest that pure PA6 shows Newtonian behavior.However,the novel EPA6N exhibits a solid-like rheological behavior,which is due to the small size,large surface of silica particles and the stronger polyamide 6-silica chemical bond formed through the reactions of epoxy resins with end groups of PA6 molecular chains.The EPA6N also exhibits higher melt viscosity,storage modulus and loss modulus than those of pure PA6.
