A plasmonic filter and sensor is designed based on an end-coupled ring-groove composited resonator(RGCR).According to the magnetic field distributions of the resonance modes,a horizontal or vertical groove is added to...A plasmonic filter and sensor is designed based on an end-coupled ring-groove composited resonator(RGCR).According to the magnetic field distributions of the resonance modes,a horizontal or vertical groove is added to the perfect ring resonator,and the transmission peaks for the 1st and the 2nd modes can be linearly changed by the length of the groove.In this case,the proposed structure can act as an on-chip optical filter with flexible wavelength manipulation.When the groove is rotated with an angle of?/4,Fano resonance arises due to the mode interference.Dual asymmetric sharp transmission peaks are achieved around the wavelength of the former 2nd resonance mode.High figure of merit and high sensitivity are obtained for the structure,and it is believed that the device can find widely applications in the biochemistry sensing area.The corresponding spectra and the propagation characteristics are numerically investigated by using the finite-difference time-domain method.展开更多
The equivalent two-port network model of a middle range wireless power transfer(WPT) system was presented based on strongly coupled multiple resonators. The key parameters of the WPT system include self-inductance, re...The equivalent two-port network model of a middle range wireless power transfer(WPT) system was presented based on strongly coupled multiple resonators. The key parameters of the WPT system include self-inductance, resistance, parasitic capacitance, mutual inductance and S-parameters of coils & resonators were analyzed. The impedance matching method was used to optimize load power and transmission efficiency of the multi-resonator WPT system, and the impedance matching method was realized through adjusting the distances between the coils and resonators. Experiments show that the impedance matching method can effectively improve load power and transmission efficiency for middle range wireless power transfer systems with multiple resonators, at distances up to 3 times the coil radius with efficiency more than 70% and load power also close to 3.5 W.展开更多
Metamaterial based on local resonance has excellent vibration attenuation ability in low frequency.In this research,an attempt was performed to make meta-mortar with spring-mass resonators to attenuate vibration and s...Metamaterial based on local resonance has excellent vibration attenuation ability in low frequency.In this research,an attempt was performed to make meta-mortar with spring-mass resonators to attenuate vibration and shock hazards.Single-spring-mass resonators and dual-spring-mass resonators were designed and made using lead or aluminum blocks and SWPB springs encased by PMMA(polymethyl methacrylate)or aluminum frames.These resonators were placed into mortar blocks to make metamortar specimens.Vibration attenuation effect was investigated by sweeping vibration with frequency from 50 Hz to 2000 Hz.All these meta-mortar blocks exhibit excellent vibration attenuation ability in the designed band gaps.With dual-spring-mass resonators,meta-mortar blocks have two distinct vibration attenuation bands.展开更多
Combining periodic layered structure with three-dimensional cylindrical local resonators,a hybrid metastructure with improved wave isolation ability was designed and investigated through theoretical and numerical appr...Combining periodic layered structure with three-dimensional cylindrical local resonators,a hybrid metastructure with improved wave isolation ability was designed and investigated through theoretical and numerical approaches.The metastructure is composed of periodic rubber layers and concrete layers embedded with three-dimensional resonators,which can be freely designed with multi local resonant frequencies to attenuate vibrations at required frequencies and widen the attenuation bandgap.The metastructure can also effectively attenuate seismic responses.Compared with layered rubber-based structures,the metastructure has more excellent wave attenuation effects with greater attenuation and wider bandgap.展开更多
In thermoacoustic system,the characteristic of complex compliance of a regenerator has a great influence on energy stored and dissipation of the whole engine.In order to investigate the performance of regenerators wit...In thermoacoustic system,the characteristic of complex compliance of a regenerator has a great influence on energy stored and dissipation of the whole engine.In order to investigate the performance of regenerators with different matrix geometries and materials coupled with different acoustic systems,an experimental measurement and analysis method was presented.By measuring the resonant frequency,the complex compliance and quality factor of five kinds of matrix were experimentally analyzed respectively in the system of loudspeaker-driven thermoacoustic resonator(TAR)with different lengths.The experimental results show that the real part of complex compliance of the regenerator with pin-array has a maximum value among the measured matrixes and its quality factor is the largest(28.222)with the least dissipation factor of 0.035 4.So the pin-array matrix is testified to behave more excellently on the energy conversion than other matrixes.Compared with other factors the complex compliance of a regenerator contributes more to the performance of a thermoacoustic system.展开更多
The coupling efficiency of hollow-core fiber changes with temperature,which leads to the decrease of the finesse(F)of fiber resonator and limits the performance of the resonant fiber optic gyroscope(R-FOG)system.Negat...The coupling efficiency of hollow-core fiber changes with temperature,which leads to the decrease of the finesse(F)of fiber resonator and limits the performance of the resonant fiber optic gyroscope(R-FOG)system.Negative-curvature antiresonant fiber(ARF)can maintain single-mode characteristics under the condition of large mode field diameter,achieve efficient and stable fiber coupling,and significantly improve the consistency of the F of the spatial coupling resonator in variable temperature environment.A new type of ARF with a mode field diameter(MFD)of 25μm is used to fabricate a fiber resonator with a length of 5.14 m.In the range of 25℃-75℃,the average F is 31.45.The ARF resonator is used to construct an R-FOG system that shows long-term bias stability(3600 s)of3.1°/h at room temperature,4.6°/h at 75℃.To our knowledge,this is the best reported index of hollow-core fiber resonator and R-FOG system within the temperature variation range of 50℃ test.展开更多
为提高单相动态电压恢复器（dynamic voltage restorer,DVR）的补偿性能,提出一种基于等效基波及奇次谐波谐振器组的数字控制方法。采用可等效为一组谐振器的延时模块,能够有效抑制电网基波和谐波扰动。给出一种包含两个控制参数和一组...为提高单相动态电压恢复器（dynamic voltage restorer,DVR）的补偿性能,提出一种基于等效基波及奇次谐波谐振器组的数字控制方法。采用可等效为一组谐振器的延时模块,能够有效抑制电网基波和谐波扰动。给出一种包含两个控制参数和一组零相移陷波滤波器的结构及其设计方法,使系统在保证稳定性的同时,获得较大的谐振增益。其中,延时环节衰减系数可增加谐振器组鲁棒性;控制器比例增益可解决零相移陷波器中使用延时带来的问题;零相移陷波器组既能对消LC谐振峰,也能解决等效谐振器组高增益在高频处的稳定性问题。同时,引入电源电压和负载电流双前馈来保证响应速度,增加了对扰动的抑制能力。所提控制策略结构简单,谐波补偿能力强,动态响应快,易于实现。在2kW单相DVR实验装置上的实验结果验证了该控制方法的正确性。展开更多
A plasmonics waveguide structure that consist of a non-through metal–insulator–metal(MIM)waveguide coupled with a D-shaped cavity was designed.And the transmission properties,magnetic field distribution,and refracti...A plasmonics waveguide structure that consist of a non-through metal–insulator–metal(MIM)waveguide coupled with a D-shaped cavity was designed.And the transmission properties,magnetic field distribution,and refractive index sensing functionality were simulated using the finite element method(FEM).A multi-Fano resonance phenomenon was clearly observable in the transmission spectra.The Fano resonances observed in the proposed structure arise from the interaction between the discrete states of the Dshaped resonant cavity and the continuum state of the non-through MIM waveguide.The influence of structural parameters on Fano resonance modulation was investigated through systematic parameter adjustments.Additionally,the refractive index sensing properties,based on the Fano resonance,were investigated by varying the refractive index of the MIM waveguide's insulator layer.A maximum sensitivity and FOM of 1155 RIU/nm and 40 were achieved,respectively.This research opens up new possibilities for designing and exploring high-sensitivity photonic devices,micro-sensors,and innovative on-chip sensing architectures for future applications.展开更多
In order to suppress the influence of temperature changes on the performance of accelerometers,a digital quartz resonant accelerometer with low temperature drift is developed using a quartz resonator cluster as a tran...In order to suppress the influence of temperature changes on the performance of accelerometers,a digital quartz resonant accelerometer with low temperature drift is developed using a quartz resonator cluster as a transducer element.In addition,a digital intellectual property(IP) is designed in FPGA to achieve signal processing and fusion of integrated resonators.A testing system for digital quartz resonant accelerometers is established to characterize the performance under different conditions.The scale factor of the accelerometer prototype reaches 3561.63 Hz/g in the range of -1 g to +1 g,and 3542.5 Hz/g in the range of-10 g to+10 g.In different measurement ranges,the linear correlation coefficient R~2 of the accelerometer achieves greater than 0.998.The temperature drift of the accelerometer prototype is tested using a constant temperature test chamber,with a temperature change from -20℃ to 80℃.After temperature-drift compensation,the zero bias temperature coefficient falls to 0.08 mg/℃,and the scale factor temperature coefficient is 65.43 ppm/℃.The experimental results show that the digital quartz resonant accelerometer exhibits excellent sensitivity and low temperature drift.展开更多
A weakly nonlinear oscillator was modeled by a sort of differential equation, a saddle-node bifurcation was found in case of primary and secondary resonance. To control the jumping phenomena and the unstable region of...A weakly nonlinear oscillator was modeled by a sort of differential equation, a saddle-node bifurcation was found in case of primary and secondary resonance. To control the jumping phenomena and the unstable region of the nonlinear oscillator, feedback controllers were designed. Bifurcation control equations were obtained by using the multiple scales method. And through the numerical analysis, good controller could be obtained by changing the feedback control gain. Then a feasible way of further research of saddle-node bifurcation was provided. Finally, an example shows that the feedback control method applied to the hanging bridge system of gas turbine is doable.展开更多
The low field nuclear magnetic resonance (NMR), as a nondestructive and noninvasive technique, was employed to investigate the water distribution and content in cement paste with different water-to-cement ratio (w/c r...The low field nuclear magnetic resonance (NMR), as a nondestructive and noninvasive technique, was employed to investigate the water distribution and content in cement paste with different water-to-cement ratio (w/c ratio) during early and later hydration stages. From the water distribution spectrum deduced from relaxation time distribution in paste, it is suggested that the water fills in the capillary pores at initial period, and then diffuses to the mesopores and gel pores in hydration products with the hydration proceeding. The decrease of peak area in water distribution spectrum reflects the transformation from physically bound water to chemically bound water. In addition, based on the connection between relaxation time and pore size, the relative content changes of water in various states and constrained in different types of pores were also measured. The results demonstrate that it is influenced by the formation of pore system and the original water-to-cement ratio in the paste. Consequently, the relative content of capillary water is dropped to less than 2% in the paste with low w/c ratio of 0.3 when being hydrated for 1 d, while the contents are still 16% and 36% in the pastes with w/c ratios of 0.4 and 0.5, respectively.展开更多
In 1982, Professor Fang Guoliang found the "Non full resonance" phenomenon in a tool system while he use the thin-long tool ultrasonically machining deep-small hole. He called it as "local resonance&quo...In 1982, Professor Fang Guoliang found the "Non full resonance" phenomenon in a tool system while he use the thin-long tool ultrasonically machining deep-small hole. He called it as "local resonance". Also this "Non full resonance" phenomenon was discovered in the ultrasonic drilling and the ultrasonic honing system later. To its mechanism, professor Fang thought that the coupling of long-thin tool bar and driving system is weak, so the tool bar can vibrate independently, but the quantitative relation between the coupling factor and diameter ratio is not made certain. Then several theories come forth to interpret it but still haven’t a common conclusion. Through the systematic experimental and theoretical research, this paper reveals that the "local resonance" phenomenon of ultrasonic honing system has the same essence with the "local resonance" phenomenon in deep hole machining system: when the section area ratio of tool bar and driving system is small enough, some resonance frequencies of combined system are close to the resonance frequencies of "fixed-free" state tool bar, the combined system is still resonant. According to the given depth of hole and structure size, we can use the transfer matrix deduced in this paper to design flexible bar and oilstone seat not only satisfying mechanical structure size but also achieving enough magnitude. It greatly simplified the design. This new method can be named as "local resonance" design method for ultrasonic honing system. The experiment, deduction and design method have a certain common meaning to the study and design of other ultrasonic system.展开更多
When the bi-stable stochastic resonance method was applied to enhance weak thruster fault for autonomous underwater vehicle(AUV), the enhancement performance could not satisfy the detection requirement of weak thruste...When the bi-stable stochastic resonance method was applied to enhance weak thruster fault for autonomous underwater vehicle(AUV), the enhancement performance could not satisfy the detection requirement of weak thruster fault. As for this problem, a fault feature enhancement method based on mono-stable stochastic resonance was proposed. In the method, in order to improve the enhancement performance of weak thruster fault feature, the conventional bi-stable potential function was changed to mono-stable potential function which was more suitable for aperiodic signals. Furthermore, when particle swarm optimization was adopted to adjust the parameters of mono-stable stochastic resonance system, the global convergent time would be long. An improved particle swarm optimization method was developed by changing the linear inertial weighted function as nonlinear function with cosine function, so as to reduce the global convergent time. In addition, when the conventional wavelet reconstruction method was adopted to detect the weak thruster fault, undetected fault or false alarm may occur. In order to successfully detect the weak thruster fault, a weak thruster detection method was proposed based on the integration of stochastic resonance and wavelet reconstruction. In the method, the optimal reconstruction scale was determined by comparing wavelet entropies corresponding to each decomposition scale. Finally, pool-experiments were performed on AUV with thruster fault. The effectiveness of the proposed mono-stable stochastic resonance method in enhancing fault feature and reducing the global convergent time was demonstrated in comparison with particle swarm optimization based bi-stochastic resonance method. Furthermore, the effectiveness of the proposed fault detection method was illustrated in comparison with the conventional wavelet reconstruction.展开更多
This work deals with super-harmonic responses and the stabilities of a gear transmission system of a high-speed train under the stick-slip oscillation of the wheel-set.The dynamic model of the system is developed with...This work deals with super-harmonic responses and the stabilities of a gear transmission system of a high-speed train under the stick-slip oscillation of the wheel-set.The dynamic model of the system is developed with consideration on the factors including the time-varying system stiffness,the transmission error,the tooth backlash and the self-excited excitation of the wheel-set.The frequency-response equation of the system at super-harmonic resonance is obtained by the multiple scales method,and the stabilities of the system are analyzed using the perturbation theory.Complex nonlinear behaviors of the system including multi-valued solutions,jump phenomenon,hardening stiffness are found.The effects of the equivalent damping and the loads of the system under the stick-slip oscillation are analyzed.It shows that the change of the load can obviously influence the resonance frequency of the system and have little effect on the steady-state response amplitude of the system.The damping of the system has a negative effect,opposite to the load.The synthetic damping of the system composed of meshing damping and equivalent damping may be less than zero when the wheel-set has a large slippage,and the system loses its stability owing to the Hopf bifurcation.Analytical results are validated by numerical simulations.展开更多
In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action...In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.展开更多
Excessive vibration and noise radiation of the track structure can be caused by the operation of high speed trains.Though the track structure is characterized by obvious periodic properties and band gaps,the bandwidth...Excessive vibration and noise radiation of the track structure can be caused by the operation of high speed trains.Though the track structure is characterized by obvious periodic properties and band gaps,the bandwidth is narrow and the elastic wave attenuation capability within the band gap is weak.In order to effectively control the vibration and noise of track structure,the local resonance mechanism is introduced to broaden the band gap and realize wave propagation control.The locally resonant units are attached periodically on the rail,forming a new locally resonant phononic crystal structure.Then the tuning of the elastic wave band gaps of track structure is discussed,and the formation mechanism of the band gap is explicated.The research results show that a new wide and adjustable locally resonant band gap is formed after the resonant units are introduced.The phenomenon of coupling and transition can be observed between the new locally resonant band gap and the original band gap of the periodic track structure with the band gap width reaching the maximum at the coupling position.The broader band gap can be applied for vibration and noise reduction in high speed railway track structure.展开更多
In this work,the Fukui functions of the two ~2P resonance states of Be,a ~2P resonance state of Mg~–,and a ~2D resonance state of Ca~– have been determined.The trajectories of these resonance states,in conjunction w...In this work,the Fukui functions of the two ~2P resonance states of Be,a ~2P resonance state of Mg~–,and a ~2D resonance state of Ca~– have been determined.The trajectories of these resonance states,in conjunction with the complex rotation of the Hamiltonian,were used to determine their wave functions.The electron densities,Fukui functions,and values of the hyper-radius<r^2>were computed from these wave functions.The Fukui functions have negative regions in the valence shell in addition to the inner shell regions,indicating screening effects of the outer temporary electron.Selected configuration interactions with up to quadruple excitations were used along the trajectories and for computing the final wave function.Based on this data,the densities,Fukui functions,and<r^2>were calculated.展开更多
In the early fault period of high-speed train systems, the interested characteristic signals are relatively weak and easily submerged in heavy noise. In order to solve this problem, a state-transition-algorithm (STA)-...In the early fault period of high-speed train systems, the interested characteristic signals are relatively weak and easily submerged in heavy noise. In order to solve this problem, a state-transition-algorithm (STA)-based adaptive stochastic resonance (SR) method is proposed, which provides an alternative solution to the problem that the traditional SR has fixed parameters or optimizes only a single parameter and ignores the interaction between parameters. To be specific, the frequency-shifted and re-scaling are firstly used to pre-process an actual large signal to meet the requirement of the adiabatic approximate small parameter. And then, the signal-to-noise ratio is used as the optimization target, and the STA-based adaptive SR is used to synchronously optimize the system parameters. Finally, the optimal extraction and frequency recovery of a weak characteristic signal from a broken rotor bar fault are realized. The proposed method is compared with the existing methods by the early broken rotor bar experiments of traction motor. Experiment results show that the proposed method is better than the other methods in extracting weak signals, and the validity of this method is verified.展开更多
基金supported by the National Natural Science Foundation of China under Grants (61405039) and (61475037)Science and Technology Planning Projects of Guangdong Province,China under Grant (2016A 020223013)+4 种基金the Natural Science Foundation of Guangdong Province,China,under Grant (2014A030310300)the Foundation for Distinguished Young Talents in Higher Education of Guangdong,China,under Grant (2014KQNCX066)Research Fund for the Doctoral Program of Higher Education of China under Grant (20134407 110008)Guangzhou Science and Technology Project of Guangdong Province,China under Grant (2016201604030027)the Research Fund of Guangdong University of Technology under Grant (16ZK0041 ,13ZK0387)
文摘A plasmonic filter and sensor is designed based on an end-coupled ring-groove composited resonator(RGCR).According to the magnetic field distributions of the resonance modes,a horizontal or vertical groove is added to the perfect ring resonator,and the transmission peaks for the 1st and the 2nd modes can be linearly changed by the length of the groove.In this case,the proposed structure can act as an on-chip optical filter with flexible wavelength manipulation.When the groove is rotated with an angle of?/4,Fano resonance arises due to the mode interference.Dual asymmetric sharp transmission peaks are achieved around the wavelength of the former 2nd resonance mode.High figure of merit and high sensitivity are obtained for the structure,and it is believed that the device can find widely applications in the biochemistry sensing area.The corresponding spectra and the propagation characteristics are numerically investigated by using the finite-difference time-domain method.
基金Project(61104088)supported by the National Natural Science Foundation of ChinaProject(12C0741)supported by Scientific Research Fund of Hunan Provincial Education Department,China
文摘The equivalent two-port network model of a middle range wireless power transfer(WPT) system was presented based on strongly coupled multiple resonators. The key parameters of the WPT system include self-inductance, resistance, parasitic capacitance, mutual inductance and S-parameters of coils & resonators were analyzed. The impedance matching method was used to optimize load power and transmission efficiency of the multi-resonator WPT system, and the impedance matching method was realized through adjusting the distances between the coils and resonators. Experiments show that the impedance matching method can effectively improve load power and transmission efficiency for middle range wireless power transfer systems with multiple resonators, at distances up to 3 times the coil radius with efficiency more than 70% and load power also close to 3.5 W.
基金Supports from National Natural Science Foundation of China(Grant No.12002160,and Grant No.11972184)China National Key Laboratory Foundation of Science and Technology on Materials under Shock and Impact(Grant No.6142902200203)+2 种基金Natural Science Foundation of Jiangsu Province of China(Grant No.BK20200412,BK20201286)National Defense Basic Scientific Research Program of China(TCA20030)Science and Technology Project of Jiangsu Province of China(Grant No.BE2020716)。
文摘Metamaterial based on local resonance has excellent vibration attenuation ability in low frequency.In this research,an attempt was performed to make meta-mortar with spring-mass resonators to attenuate vibration and shock hazards.Single-spring-mass resonators and dual-spring-mass resonators were designed and made using lead or aluminum blocks and SWPB springs encased by PMMA(polymethyl methacrylate)or aluminum frames.These resonators were placed into mortar blocks to make metamortar specimens.Vibration attenuation effect was investigated by sweeping vibration with frequency from 50 Hz to 2000 Hz.All these meta-mortar blocks exhibit excellent vibration attenuation ability in the designed band gaps.With dual-spring-mass resonators,meta-mortar blocks have two distinct vibration attenuation bands.
基金Supports from National Natural Science Foundation of China(Grant Nos.U20A20286 and 11972184)the Systematic Project of Guangxi Key Laboratory of Disaster Prevention and Engineering Safety(Grant No.2021ZDK006)+1 种基金Natural Science Foundation of Jiangsu Province of China(Grant No.BK20201286)Science and Technology Project of Jiangsu Province of China(Grant No.BE2020716)are gratefully acknowledged.
文摘Combining periodic layered structure with three-dimensional cylindrical local resonators,a hybrid metastructure with improved wave isolation ability was designed and investigated through theoretical and numerical approaches.The metastructure is composed of periodic rubber layers and concrete layers embedded with three-dimensional resonators,which can be freely designed with multi local resonant frequencies to attenuate vibrations at required frequencies and widen the attenuation bandgap.The metastructure can also effectively attenuate seismic responses.Compared with layered rubber-based structures,the metastructure has more excellent wave attenuation effects with greater attenuation and wider bandgap.
基金Projects(50676068,50576024)supported by the National Natural Science Foundation of China
文摘In thermoacoustic system,the characteristic of complex compliance of a regenerator has a great influence on energy stored and dissipation of the whole engine.In order to investigate the performance of regenerators with different matrix geometries and materials coupled with different acoustic systems,an experimental measurement and analysis method was presented.By measuring the resonant frequency,the complex compliance and quality factor of five kinds of matrix were experimentally analyzed respectively in the system of loudspeaker-driven thermoacoustic resonator(TAR)with different lengths.The experimental results show that the real part of complex compliance of the regenerator with pin-array has a maximum value among the measured matrixes and its quality factor is the largest(28.222)with the least dissipation factor of 0.035 4.So the pin-array matrix is testified to behave more excellently on the energy conversion than other matrixes.Compared with other factors the complex compliance of a regenerator contributes more to the performance of a thermoacoustic system.
基金supported by the National Natural Science Foundation of China(61973019)。
文摘The coupling efficiency of hollow-core fiber changes with temperature,which leads to the decrease of the finesse(F)of fiber resonator and limits the performance of the resonant fiber optic gyroscope(R-FOG)system.Negative-curvature antiresonant fiber(ARF)can maintain single-mode characteristics under the condition of large mode field diameter,achieve efficient and stable fiber coupling,and significantly improve the consistency of the F of the spatial coupling resonator in variable temperature environment.A new type of ARF with a mode field diameter(MFD)of 25μm is used to fabricate a fiber resonator with a length of 5.14 m.In the range of 25℃-75℃,the average F is 31.45.The ARF resonator is used to construct an R-FOG system that shows long-term bias stability(3600 s)of3.1°/h at room temperature,4.6°/h at 75℃.To our knowledge,this is the best reported index of hollow-core fiber resonator and R-FOG system within the temperature variation range of 50℃ test.
文摘为提高单相动态电压恢复器（dynamic voltage restorer,DVR）的补偿性能,提出一种基于等效基波及奇次谐波谐振器组的数字控制方法。采用可等效为一组谐振器的延时模块,能够有效抑制电网基波和谐波扰动。给出一种包含两个控制参数和一组零相移陷波滤波器的结构及其设计方法,使系统在保证稳定性的同时,获得较大的谐振增益。其中,延时环节衰减系数可增加谐振器组鲁棒性;控制器比例增益可解决零相移陷波器中使用延时带来的问题;零相移陷波器组既能对消LC谐振峰,也能解决等效谐振器组高增益在高频处的稳定性问题。同时,引入电源电压和负载电流双前馈来保证响应速度,增加了对扰动的抑制能力。所提控制策略结构简单,谐波补偿能力强,动态响应快,易于实现。在2kW单相DVR实验装置上的实验结果验证了该控制方法的正确性。
文摘A plasmonics waveguide structure that consist of a non-through metal–insulator–metal(MIM)waveguide coupled with a D-shaped cavity was designed.And the transmission properties,magnetic field distribution,and refractive index sensing functionality were simulated using the finite element method(FEM).A multi-Fano resonance phenomenon was clearly observable in the transmission spectra.The Fano resonances observed in the proposed structure arise from the interaction between the discrete states of the Dshaped resonant cavity and the continuum state of the non-through MIM waveguide.The influence of structural parameters on Fano resonance modulation was investigated through systematic parameter adjustments.Additionally,the refractive index sensing properties,based on the Fano resonance,were investigated by varying the refractive index of the MIM waveguide's insulator layer.A maximum sensitivity and FOM of 1155 RIU/nm and 40 were achieved,respectively.This research opens up new possibilities for designing and exploring high-sensitivity photonic devices,micro-sensors,and innovative on-chip sensing architectures for future applications.
文摘In order to suppress the influence of temperature changes on the performance of accelerometers,a digital quartz resonant accelerometer with low temperature drift is developed using a quartz resonator cluster as a transducer element.In addition,a digital intellectual property(IP) is designed in FPGA to achieve signal processing and fusion of integrated resonators.A testing system for digital quartz resonant accelerometers is established to characterize the performance under different conditions.The scale factor of the accelerometer prototype reaches 3561.63 Hz/g in the range of -1 g to +1 g,and 3542.5 Hz/g in the range of-10 g to+10 g.In different measurement ranges,the linear correlation coefficient R~2 of the accelerometer achieves greater than 0.998.The temperature drift of the accelerometer prototype is tested using a constant temperature test chamber,with a temperature change from -20℃ to 80℃.After temperature-drift compensation,the zero bias temperature coefficient falls to 0.08 mg/℃,and the scale factor temperature coefficient is 65.43 ppm/℃.The experimental results show that the digital quartz resonant accelerometer exhibits excellent sensitivity and low temperature drift.
基金Project(10672053) supported by the National Natural Science Foundation of ChinaProject(2002AA503010) supported by the National High-Tech Research and Development Program of China
文摘A weakly nonlinear oscillator was modeled by a sort of differential equation, a saddle-node bifurcation was found in case of primary and secondary resonance. To control the jumping phenomena and the unstable region of the nonlinear oscillator, feedback controllers were designed. Bifurcation control equations were obtained by using the multiple scales method. And through the numerical analysis, good controller could be obtained by changing the feedback control gain. Then a feasible way of further research of saddle-node bifurcation was provided. Finally, an example shows that the feedback control method applied to the hanging bridge system of gas turbine is doable.
基金Project(2009CB623105) supported by the National Basic Research Program of ChinaProject(51108341) supported by the National Natural Science Foundation of ChinaProjects(20110490703, 2012T50437) supported by China Postdoctoral Science Foundation
文摘The low field nuclear magnetic resonance (NMR), as a nondestructive and noninvasive technique, was employed to investigate the water distribution and content in cement paste with different water-to-cement ratio (w/c ratio) during early and later hydration stages. From the water distribution spectrum deduced from relaxation time distribution in paste, it is suggested that the water fills in the capillary pores at initial period, and then diffuses to the mesopores and gel pores in hydration products with the hydration proceeding. The decrease of peak area in water distribution spectrum reflects the transformation from physically bound water to chemically bound water. In addition, based on the connection between relaxation time and pore size, the relative content changes of water in various states and constrained in different types of pores were also measured. The results demonstrate that it is influenced by the formation of pore system and the original water-to-cement ratio in the paste. Consequently, the relative content of capillary water is dropped to less than 2% in the paste with low w/c ratio of 0.3 when being hydrated for 1 d, while the contents are still 16% and 36% in the pastes with w/c ratios of 0.4 and 0.5, respectively.
文摘In 1982, Professor Fang Guoliang found the "Non full resonance" phenomenon in a tool system while he use the thin-long tool ultrasonically machining deep-small hole. He called it as "local resonance". Also this "Non full resonance" phenomenon was discovered in the ultrasonic drilling and the ultrasonic honing system later. To its mechanism, professor Fang thought that the coupling of long-thin tool bar and driving system is weak, so the tool bar can vibrate independently, but the quantitative relation between the coupling factor and diameter ratio is not made certain. Then several theories come forth to interpret it but still haven’t a common conclusion. Through the systematic experimental and theoretical research, this paper reveals that the "local resonance" phenomenon of ultrasonic honing system has the same essence with the "local resonance" phenomenon in deep hole machining system: when the section area ratio of tool bar and driving system is small enough, some resonance frequencies of combined system are close to the resonance frequencies of "fixed-free" state tool bar, the combined system is still resonant. According to the given depth of hole and structure size, we can use the transfer matrix deduced in this paper to design flexible bar and oilstone seat not only satisfying mechanical structure size but also achieving enough magnitude. It greatly simplified the design. This new method can be named as "local resonance" design method for ultrasonic honing system. The experiment, deduction and design method have a certain common meaning to the study and design of other ultrasonic system.
基金Project(51279040)supported by the National Natural Science Foundation of China
文摘When the bi-stable stochastic resonance method was applied to enhance weak thruster fault for autonomous underwater vehicle(AUV), the enhancement performance could not satisfy the detection requirement of weak thruster fault. As for this problem, a fault feature enhancement method based on mono-stable stochastic resonance was proposed. In the method, in order to improve the enhancement performance of weak thruster fault feature, the conventional bi-stable potential function was changed to mono-stable potential function which was more suitable for aperiodic signals. Furthermore, when particle swarm optimization was adopted to adjust the parameters of mono-stable stochastic resonance system, the global convergent time would be long. An improved particle swarm optimization method was developed by changing the linear inertial weighted function as nonlinear function with cosine function, so as to reduce the global convergent time. In addition, when the conventional wavelet reconstruction method was adopted to detect the weak thruster fault, undetected fault or false alarm may occur. In order to successfully detect the weak thruster fault, a weak thruster detection method was proposed based on the integration of stochastic resonance and wavelet reconstruction. In the method, the optimal reconstruction scale was determined by comparing wavelet entropies corresponding to each decomposition scale. Finally, pool-experiments were performed on AUV with thruster fault. The effectiveness of the proposed mono-stable stochastic resonance method in enhancing fault feature and reducing the global convergent time was demonstrated in comparison with particle swarm optimization based bi-stochastic resonance method. Furthermore, the effectiveness of the proposed fault detection method was illustrated in comparison with the conventional wavelet reconstruction.
基金Project(U1234208)supported by the National Natural Science Foundation of ChinaProject(2016YFB1200401)supported by the National Key Research and Development Program of China
文摘This work deals with super-harmonic responses and the stabilities of a gear transmission system of a high-speed train under the stick-slip oscillation of the wheel-set.The dynamic model of the system is developed with consideration on the factors including the time-varying system stiffness,the transmission error,the tooth backlash and the self-excited excitation of the wheel-set.The frequency-response equation of the system at super-harmonic resonance is obtained by the multiple scales method,and the stabilities of the system are analyzed using the perturbation theory.Complex nonlinear behaviors of the system including multi-valued solutions,jump phenomenon,hardening stiffness are found.The effects of the equivalent damping and the loads of the system under the stick-slip oscillation are analyzed.It shows that the change of the load can obviously influence the resonance frequency of the system and have little effect on the steady-state response amplitude of the system.The damping of the system has a negative effect,opposite to the load.The synthetic damping of the system composed of meshing damping and equivalent damping may be less than zero when the wheel-set has a large slippage,and the system loses its stability owing to the Hopf bifurcation.Analytical results are validated by numerical simulations.
文摘In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.
基金Project(2016YFE0205200)supported by the National Key Research and Development Program of ChinaProjects(51425804,51508479)supported by the National Natural Science Foundation of China+1 种基金Project(2016310019)supported by the Doctorial Innovation Fund of Southwest Jiaotong University,ChinaProject(2017GZ0373)supported by the Research Fund for Key Research and Development Projects in Sichuan Province,China
文摘Excessive vibration and noise radiation of the track structure can be caused by the operation of high speed trains.Though the track structure is characterized by obvious periodic properties and band gaps,the bandwidth is narrow and the elastic wave attenuation capability within the band gap is weak.In order to effectively control the vibration and noise of track structure,the local resonance mechanism is introduced to broaden the band gap and realize wave propagation control.The locally resonant units are attached periodically on the rail,forming a new locally resonant phononic crystal structure.Then the tuning of the elastic wave band gaps of track structure is discussed,and the formation mechanism of the band gap is explicated.The research results show that a new wide and adjustable locally resonant band gap is formed after the resonant units are introduced.The phenomenon of coupling and transition can be observed between the new locally resonant band gap and the original band gap of the periodic track structure with the band gap width reaching the maximum at the coupling position.The broader band gap can be applied for vibration and noise reduction in high speed railway track structure.
文摘In this work,the Fukui functions of the two ~2P resonance states of Be,a ~2P resonance state of Mg~–,and a ~2D resonance state of Ca~– have been determined.The trajectories of these resonance states,in conjunction with the complex rotation of the Hamiltonian,were used to determine their wave functions.The electron densities,Fukui functions,and values of the hyper-radius<r^2>were computed from these wave functions.The Fukui functions have negative regions in the valence shell in addition to the inner shell regions,indicating screening effects of the outer temporary electron.Selected configuration interactions with up to quadruple excitations were used along the trajectories and for computing the final wave function.Based on this data,the densities,Fukui functions,and<r^2>were calculated.
基金Projects(61490702,61773407,61803390,61751312)supported by the National Natural Science Foundation of ChinaProject(61725306)supported by the National Science Foundation for Distinguished Young Scholars of China+5 种基金Project(61621062)supported by the Foundation for Innovative Research Groups of the National Natural Science Foundation of ChinaProject(2017TP1002)supported by Hunan Provincial Key Laboratory,ChinaProject(6141A0202210)supported by the Program of the Joint Pre-research Foundation of the Chinese Ministry of EducationProject(61400030501)supported by the General Program of the Equipment Pre-research Field Foundation of ChinaProject(2016TP1023)supported by the Science and Technology Project in Hunan Province Hunan Science and Technology Agency of ChinaProject(2018FJ34)supported by the Science and Technology Project in Shaoyang Science and Technology Agency of China
文摘In the early fault period of high-speed train systems, the interested characteristic signals are relatively weak and easily submerged in heavy noise. In order to solve this problem, a state-transition-algorithm (STA)-based adaptive stochastic resonance (SR) method is proposed, which provides an alternative solution to the problem that the traditional SR has fixed parameters or optimizes only a single parameter and ignores the interaction between parameters. To be specific, the frequency-shifted and re-scaling are firstly used to pre-process an actual large signal to meet the requirement of the adiabatic approximate small parameter. And then, the signal-to-noise ratio is used as the optimization target, and the STA-based adaptive SR is used to synchronously optimize the system parameters. Finally, the optimal extraction and frequency recovery of a weak characteristic signal from a broken rotor bar fault are realized. The proposed method is compared with the existing methods by the early broken rotor bar experiments of traction motor. Experiment results show that the proposed method is better than the other methods in extracting weak signals, and the validity of this method is verified.
