The electrostatic discharge(ESD)protection circuit widely exists in the input and output ports of CMOS digital circuits,and fast rising time electromagnetic pulse(FREMP)coupled into the device not only interacts with ...The electrostatic discharge(ESD)protection circuit widely exists in the input and output ports of CMOS digital circuits,and fast rising time electromagnetic pulse(FREMP)coupled into the device not only interacts with the CMOS circuit,but also acts on the protection circuit.This paper establishes a model of on-chip CMOS electrostatic discharge protection circuit and selects square pulse as the FREMP signals.Based on multiple physical parameter models,it depicts the distribution of the lattice temperature,current density,and electric field intensity inside the device.At the same time,this paper explores the changes of the internal devices in the circuit under the injection of fast rising time electromagnetic pulse and describes the relationship between the damage amplitude threshold and the pulse width.The results show that the ESD protection circuit has potential damage risk,and the injection of FREMP leads to irreversible heat loss inside the circuit.In addition,pulse signals with different attributes will change the damage threshold of the circuit.These results provide an important reference for further evaluation of the influence of electromagnetic environment on the chip,which is helpful to carry out the reliability enhancement research of ESD protection circuit.展开更多
In this paper a fully parametrized finite element simulation model of the stator bar end is created using the COMSOL Multiphysics.The model allows conducting the comparison of different corona protection structures’d...In this paper a fully parametrized finite element simulation model of the stator bar end is created using the COMSOL Multiphysics.The model allows conducting the comparison of different corona protection structures’design,various materials properties,and finally optimizing the corona protection system.Several samples of SiC based nonlinear conductivity materials for corona protection were fabricated in laboratory and then investigated.The conductivity dependencies on electric field(0.05 to 1 kV/mm)and temperature(20 to 155℃)were measured.By comparing the heat-resistant grades of the corona protection material and the insulating material,the maximum working temperature of the corona protection material corresponds to the heat-resistant grade F of the insulating material.As the temperature increases,the nonlinear characteristics of the corona protection material in the experiment decrease dramatically,reducing the heat-resistant grade of the corona protection material.The decrease in the nonlinear characteristics of the corona protection material at the maximum operating temperature causes the maximum electric field strength at the end of the HV rotating machines end corona protection(ECP)exceeding the corona discharge electric field strength,resulting in corona phenomenon.展开更多
Spherical Ni（OH）2 particles were prepared by an aqueous solution precipitation route. The structure of spherical Ni（OH）2 was investigated by scanning electron microscopy and transmission electron microscopy and co...Spherical Ni（OH）2 particles were prepared by an aqueous solution precipitation route. The structure of spherical Ni（OH）2 was investigated by scanning electron microscopy and transmission electron microscopy and compared with that of traditional Ni（OH）2. The results show that the spherical nickel hydroxide consists of （Ni（OH）2） spheres with a reticulate structure of platelet-like, which is almost arranged radially and the crystalline grains intervene and connect with each other to form a three-dimensional net. The spherical Ni（OH）2 particle is full of pores, crannies between cleave planes. It is supposed that this structure is beneficial to the structural stability for the spherical particles during the charge/discharge processes and can improve the cycle life of the electrode; the pores and the crannies in spherical particles can shorten the proton diffusion distance and speed its velocity, which may result in that the local polarization is lowered. The electrochemical performances of the spherical Ni（OH）2 are improved by enhancing the conducting properties of the crystalline lattice due to its quick proton diffusion.展开更多
Dielectric barrier discharge(DBD) is widely investigated in order to obtain uniform low-temperature plasma.Many studies have proved that some barrier materials,especially electrets,can improve the uniformity of discha...Dielectric barrier discharge(DBD) is widely investigated in order to obtain uniform low-temperature plasma.Many studies have proved that some barrier materials,especially electrets,can improve the uniformity of discharge.It is regarded as an available way to get atmospheric pressure glow discharge(APGD).In this paper,discharge forms with 4 different barrier materials(alumina,quartz,PTFE and PET) are investigated,and the transition of discharge form depending on the air pressure are recorded to estimate the influence of barrier materials on discharge.By using electrets as barrier materials,homogeneous discharges can be obtained in a more wide pressure range.Under the same experimental conditions,discharges with electrets are more uniform or have larger uniform areas due to the storage and desorption of charges on the surface of electrets.The electrons deposited in the surface layer can be released on next half cycle when the polarity of the applied voltage changes,and provide a number of seed electrons,which makes the discharge more homogeneous.The capacitance and the permittivity of barrier materials have no effect on the discharge form directly.展开更多
The space charge behavior of a dielectric under HVDC is influenced by the charge trap energy distribution in it. Hence, we in- vestigated the charge trap distributions in several kinds of typical polymer materials usi...The space charge behavior of a dielectric under HVDC is influenced by the charge trap energy distribution in it. Hence, we in- vestigated the charge trap distributions in several kinds of typical polymer materials using thermally stimulated discharge (TSD) and photo-stimulated discharge (PSD) methods, respectively. The experimental results show that,there is a significant difference between the trap energy distributions obtained by the two methods, but the difference decreases with the increase of the melting point of polymers. This is attributed to the change of the trap center environment during TSD caused by the increasing movements of both main chains and branched chains in polymers. PSD method is more accurate for investigating charge trap distribution in dielectrics, especially for polymers with low melting points.展开更多
A certain number of charges are deposited on the surface of high-voltage solar array because of effects of space plasma,high-energy charged particles,and solar illumination,hence the surface is charged.Phenomena of el...A certain number of charges are deposited on the surface of high-voltage solar array because of effects of space plasma,high-energy charged particles,and solar illumination,hence the surface is charged.Phenomena of electrostatic discharge(ESD) occur on the surface when the deposited charges exceed a threshold amount.In this paper,the mechanism of this ESD is discussed.The ground simulation experiment of the ESD using spacecraft material under surface charging is described,and a novel ESD protecting method for high-voltage solar array,i.e.an active protecting method based on the local strong electric field array is proposed.The results show that the reversal potential gradient field between the cover surface and the substrate materials of high-voltage solar array is a triggering factor for the ESD on the array.The threshold voltage for the ESD occurring on the surface is about 500 V.The charged particles could be deflected using the electric field active protecting method,and hence the ESD on the surface is avoided even when the voltage on the conductor array increases to a certain value.These results pave the way for further developing the protecting measures for high-voltage solar arrays.展开更多
Beyond Earth,electrical discharges have also been observed,or postulated to exist,on other bodies of the Solar System.In this work the state of the art of research on electrical discharges in the atmosphere of several...Beyond Earth,electrical discharges have also been observed,or postulated to exist,on other bodies of the Solar System.In this work the state of the art of research on electrical discharges in the atmosphere of several planets and one moon is reported.The main charging mechanisms as well as the discharge characteristics and its effect on the atmosphere are discussed.Some of the current research activities being carried out by the author’s team are also reported.The lab simulations can achieve realistic plasma parameters;for example:the arc temperature in the lab was found to be 33 000 K which compares favourably with field observations reporting temperatures～30 000K.The lab work with a synthetic Mars atmosphere allow us to predict that the conjunction of electrostatic discharges and the presence of water ice could lead to the production of methane with an efficiency of up to 1021molecules per joule of applied energy.展开更多
In addition to the conventional Franklin Rod,many non-conventional air terminals are being used as lightning protection devices.As cited in previous works,these non-conventional devices emit space charge in the vicini...In addition to the conventional Franklin Rod,many non-conventional air terminals are being used as lightning protection devices.As cited in previous works,these non-conventional devices emit space charge in the vicinity of the terminals during the process of lightning stroke.A number of factors affect the performance of these lightning protection devices,among them are geometry and dimension of the devices,location of the device above the ground,height of the cloud above the ground,and polarity of the lightning stroke.The performance of these lightning protection devices has been a topic of discussion by researchers for many years.Some studies focused on the magnitude of emission current from these devices as a criterion to evaluate their performances.The critical flashover voltage(CFO)between the devices and a metal screen simulating cloud can also be used as another criterion to evaluate the performance of the devices.Laboratory measurements were conducted in controlled conditions on different types of lightning protection devices to compare their performance.Four different types of devices were used in the present study:Franklin Rod,TerraStat models TS 100,TS 400,and Spline Ball Ionizer.The study focused on the CFO voltage of the air gap between devices and the metal screen.The CFO voltage was evaluated using standard switching and lightning impulses.The measurements were recorded for positive as well as negative polarity.The air gap between the devices and metal screen was selected at 2 m and 3 m.The results obtained provide a better understanding of the electrical performance of lightning protection devices.展开更多
基金National Natural Science Foundation of China(61974116)。
文摘The electrostatic discharge(ESD)protection circuit widely exists in the input and output ports of CMOS digital circuits,and fast rising time electromagnetic pulse(FREMP)coupled into the device not only interacts with the CMOS circuit,but also acts on the protection circuit.This paper establishes a model of on-chip CMOS electrostatic discharge protection circuit and selects square pulse as the FREMP signals.Based on multiple physical parameter models,it depicts the distribution of the lattice temperature,current density,and electric field intensity inside the device.At the same time,this paper explores the changes of the internal devices in the circuit under the injection of fast rising time electromagnetic pulse and describes the relationship between the damage amplitude threshold and the pulse width.The results show that the ESD protection circuit has potential damage risk,and the injection of FREMP leads to irreversible heat loss inside the circuit.In addition,pulse signals with different attributes will change the damage threshold of the circuit.These results provide an important reference for further evaluation of the influence of electromagnetic environment on the chip,which is helpful to carry out the reliability enhancement research of ESD protection circuit.
文摘In this paper a fully parametrized finite element simulation model of the stator bar end is created using the COMSOL Multiphysics.The model allows conducting the comparison of different corona protection structures’design,various materials properties,and finally optimizing the corona protection system.Several samples of SiC based nonlinear conductivity materials for corona protection were fabricated in laboratory and then investigated.The conductivity dependencies on electric field(0.05 to 1 kV/mm)and temperature(20 to 155℃)were measured.By comparing the heat-resistant grades of the corona protection material and the insulating material,the maximum working temperature of the corona protection material corresponds to the heat-resistant grade F of the insulating material.As the temperature increases,the nonlinear characteristics of the corona protection material in the experiment decrease dramatically,reducing the heat-resistant grade of the corona protection material.The decrease in the nonlinear characteristics of the corona protection material at the maximum operating temperature causes the maximum electric field strength at the end of the HV rotating machines end corona protection(ECP)exceeding the corona discharge electric field strength,resulting in corona phenomenon.
基金Project(50134020) supported by the National Natural Science Foundation of China
文摘Spherical Ni（OH）2 particles were prepared by an aqueous solution precipitation route. The structure of spherical Ni（OH）2 was investigated by scanning electron microscopy and transmission electron microscopy and compared with that of traditional Ni（OH）2. The results show that the spherical nickel hydroxide consists of （Ni（OH）2） spheres with a reticulate structure of platelet-like, which is almost arranged radially and the crystalline grains intervene and connect with each other to form a three-dimensional net. The spherical Ni（OH）2 particle is full of pores, crannies between cleave planes. It is supposed that this structure is beneficial to the structural stability for the spherical particles during the charge/discharge processes and can improve the cycle life of the electrode; the pores and the crannies in spherical particles can shorten the proton diffusion distance and speed its velocity, which may result in that the local polarization is lowered. The electrochemical performances of the spherical Ni（OH）2 are improved by enhancing the conducting properties of the crystalline lattice due to its quick proton diffusion.
基金Project Supported by National Natural Science Foundation of China(50537020,50507003)Specialized Research Fund for the Doc-toral Programof High Education of China(20050079006).
文摘Dielectric barrier discharge(DBD) is widely investigated in order to obtain uniform low-temperature plasma.Many studies have proved that some barrier materials,especially electrets,can improve the uniformity of discharge.It is regarded as an available way to get atmospheric pressure glow discharge(APGD).In this paper,discharge forms with 4 different barrier materials(alumina,quartz,PTFE and PET) are investigated,and the transition of discharge form depending on the air pressure are recorded to estimate the influence of barrier materials on discharge.By using electrets as barrier materials,homogeneous discharges can be obtained in a more wide pressure range.Under the same experimental conditions,discharges with electrets are more uniform or have larger uniform areas due to the storage and desorption of charges on the surface of electrets.The electrons deposited in the surface layer can be released on next half cycle when the polarity of the applied voltage changes,and provide a number of seed electrons,which makes the discharge more homogeneous.The capacitance and the permittivity of barrier materials have no effect on the discharge form directly.
基金Project supported by National Natural Science Foundation of China （51077101, 51277133）, National Basic Research Program of China （973 Program） （2009CB 724505）.
文摘The space charge behavior of a dielectric under HVDC is influenced by the charge trap energy distribution in it. Hence, we in- vestigated the charge trap distributions in several kinds of typical polymer materials using thermally stimulated discharge (TSD) and photo-stimulated discharge (PSD) methods, respectively. The experimental results show that,there is a significant difference between the trap energy distributions obtained by the two methods, but the difference decreases with the increase of the melting point of polymers. This is attributed to the change of the trap center environment during TSD caused by the increasing movements of both main chains and branched chains in polymers. PSD method is more accurate for investigating charge trap distribution in dielectrics, especially for polymers with low melting points.
基金Project supported by National Natural Science Foundation of China（51177173）, Elec- tromagnetic Environment Effect Key Laboratory Foundation（9140C87010313 JB34004）.
文摘A certain number of charges are deposited on the surface of high-voltage solar array because of effects of space plasma,high-energy charged particles,and solar illumination,hence the surface is charged.Phenomena of electrostatic discharge(ESD) occur on the surface when the deposited charges exceed a threshold amount.In this paper,the mechanism of this ESD is discussed.The ground simulation experiment of the ESD using spacecraft material under surface charging is described,and a novel ESD protecting method for high-voltage solar array,i.e.an active protecting method based on the local strong electric field array is proposed.The results show that the reversal potential gradient field between the cover surface and the substrate materials of high-voltage solar array is a triggering factor for the ESD on the array.The threshold voltage for the ESD occurring on the surface is about 500 V.The charged particles could be deflected using the electric field active protecting method,and hence the ESD on the surface is avoided even when the voltage on the conductor array increases to a certain value.These results pave the way for further developing the protecting measures for high-voltage solar arrays.
基金Project supported by Mexican Science Council(CONACyT)(Grant No.155673)
文摘Beyond Earth,electrical discharges have also been observed,or postulated to exist,on other bodies of the Solar System.In this work the state of the art of research on electrical discharges in the atmosphere of several planets and one moon is reported.The main charging mechanisms as well as the discharge characteristics and its effect on the atmosphere are discussed.Some of the current research activities being carried out by the author’s team are also reported.The lab simulations can achieve realistic plasma parameters;for example:the arc temperature in the lab was found to be 33 000 K which compares favourably with field observations reporting temperatures～30 000K.The lab work with a synthetic Mars atmosphere allow us to predict that the conjunction of electrostatic discharges and the presence of water ice could lead to the production of methane with an efficiency of up to 1021molecules per joule of applied energy.
文摘In addition to the conventional Franklin Rod,many non-conventional air terminals are being used as lightning protection devices.As cited in previous works,these non-conventional devices emit space charge in the vicinity of the terminals during the process of lightning stroke.A number of factors affect the performance of these lightning protection devices,among them are geometry and dimension of the devices,location of the device above the ground,height of the cloud above the ground,and polarity of the lightning stroke.The performance of these lightning protection devices has been a topic of discussion by researchers for many years.Some studies focused on the magnitude of emission current from these devices as a criterion to evaluate their performances.The critical flashover voltage(CFO)between the devices and a metal screen simulating cloud can also be used as another criterion to evaluate the performance of the devices.Laboratory measurements were conducted in controlled conditions on different types of lightning protection devices to compare their performance.Four different types of devices were used in the present study:Franklin Rod,TerraStat models TS 100,TS 400,and Spline Ball Ionizer.The study focused on the CFO voltage of the air gap between devices and the metal screen.The CFO voltage was evaluated using standard switching and lightning impulses.The measurements were recorded for positive as well as negative polarity.The air gap between the devices and metal screen was selected at 2 m and 3 m.The results obtained provide a better understanding of the electrical performance of lightning protection devices.
