One of the detection objectives of the Chinese Asteroid Exploration mission is to investigate the space environment near the Main-belt Comet(MBC,Active Asteroid)311P/PANSTARRS.This paper outlines the scientific object...One of the detection objectives of the Chinese Asteroid Exploration mission is to investigate the space environment near the Main-belt Comet(MBC,Active Asteroid)311P/PANSTARRS.This paper outlines the scientific objectives,measurement targets,and measurement requirements for the proposed Gas and Ion Analyzer(GIA).The GIA is designed for in-situ mass spectrometry of neutral gases and low-energy ions,such as hydrogen,carbon,and oxygen,in the vicinity of 311P.Ion sampling techniques are essential for the GIA's Time-of-Flight(TOF)mass analysis capabilities.In this paper,we present an enhanced ion sampling technique through the development of an ion attraction model and an ion source model.The ion attraction model demonstrates that adjusting attraction grid voltage can enhance the detection efficiency of low-energy ions and mitigate the repulsive force of ions during sampling,which is influenced by the satellite's surface positive charging.The ion source model simulates the processes of gas ionization and ion multiplication.Simulation results indicate that the GIA can achieve a lower pressure limit below 10-13Pa and possess a dynamic range exceeding 10~9.These performances ensure the generation of ions with stable and consistent current,which is crucial for high-resolution and broad dynamic range mass spectrometer analysis.Preliminary testing experiments have verified GIA's capability to detect gas compositions such as H2O and N2.In-situ measurements near 311P using GIA are expected to significantly contribute to our understanding of asteroid activity mechanisms,the evolution of the atmospheric and ionized environments of main-belt comets,the interactions with solar wind,and the origin of Earth's water.展开更多
The initial motivation of the lifting technique is to solve the H∞control problems. However, the conventional weighted H∞design does not meet the conditions required by lifting, so the result often leads to a misjud...The initial motivation of the lifting technique is to solve the H∞control problems. However, the conventional weighted H∞design does not meet the conditions required by lifting, so the result often leads to a misjudgement of the design. Two conditions required by using the lifting technique are presented based on the basic formulae of the lifting. It is pointed out that only the H∞disturbance attenuation problem with no weighting functions can meet these conditions, hence, the application of the lifting technique is quite limited.展开更多
An agile missile with tail fins and pulse thrusters has continuous and discontinuous control inputs.This brings certain difficulty to the autopilot design and stability analysis.Indirect robust control via Theta-D tec...An agile missile with tail fins and pulse thrusters has continuous and discontinuous control inputs.This brings certain difficulty to the autopilot design and stability analysis.Indirect robust control via Theta-D technique is employed to handle this problem.An acceleration tracking system is formulated based on the nonlinear dynamics of agile missile.Considering the dynamics of actuators,there is an error between actual input and computed input.A robust control problem is formed by treating the error as input uncertainty.The robust control is equivalent to a nonlinear quadratic optimal control of the nominal system with a modified performance index including uncertainty bound.Theta-D technique is applied to solve the nonlinear optimal control problem to obtain the final control law.Numerical results show the effectiveness and robustness of the proposed strategy.展开更多
The cross-efficiency evaluation method is reviewed which is developed as a data envelopment analysis （DEA） extensive tool. The cross-efficiency evaluation method is utilized to identify the decision making unit （DM...The cross-efficiency evaluation method is reviewed which is developed as a data envelopment analysis （DEA） extensive tool. The cross-efficiency evaluation method is utilized to identify the decision making unit （DMU） with the best practice and to rank the DMUs by their respective cross-efficiency scores. The main drawbacks of the cross-efficiency evaluation method when the ultimate average cross-efficiency scores are used to evalu- ate and rank the DMUs are also pointed out. With the research gap, an improved technique for order preference by similarity to ideal solution （TOPSIS） is introduced to rank the crossfficiency by eliminating the average assumption. Finally, an empirical example is illustrated to examine the validity of the proposed method.展开更多
Based on the nonlinear failure criterion and the upper bound theorem, the modified tangential technique method was proposed to derive the expression of supporting pressure acting on shallow tunnel. Instead of the same...Based on the nonlinear failure criterion and the upper bound theorem, the modified tangential technique method was proposed to derive the expression of supporting pressure acting on shallow tunnel. Instead of the same stress state, different normal stresses on element boundaries were used. In order to investigate the influence of different factors on supporting pressures, the failure mechanism was established. The solution of supporting pressure, with different parameters, was obtained by optimization theory. The corresponding failure mechanism and numerical results were presented. In comparison with the results using the single tangential technique method, it is found that the proposed method is effective, and the good agreement shows that the present solution of supporting pressure is reliable.展开更多
Methods that can efficiently model the effects of rock joints on rock mass behavior can be beneficial in rock engineering. The suitability of equivalent rock mass(ERM) technique based upon particle methods is investig...Methods that can efficiently model the effects of rock joints on rock mass behavior can be beneficial in rock engineering. The suitability of equivalent rock mass(ERM) technique based upon particle methods is investigated. The ERM methodology is first validated by comparing calculated and experimental data of lab triaxial compression test on a set of cylindrical rock mass samples, each containing a single joint oriented in various dip angles. The simulated results are then used to study the stress-strain nonlinearity and failure mechanism as a function of the joint dip angle and confining stress. The anisotropy and size effects are also investigated by using multi-scale cubic ERM models subjected to triaxial compression test. The deformation and failure behavior are found to be influenced by joint degradation, the micro-crack formation in the intact rock, the interaction between two joints, and the interactions of micro-cracks and joints.展开更多
To improve the accuracy of strapdown inertial navigation system(SINS) for long term applications,the rotation technique is employed to modulate the errors of the inertial sensors into periodically varied signals,and,a...To improve the accuracy of strapdown inertial navigation system(SINS) for long term applications,the rotation technique is employed to modulate the errors of the inertial sensors into periodically varied signals,and,as a result,to suppress the divergence of SINS errors.However,the errors of rotation platform will be introduced into SINS and might affect the final navigation accuracy.Considering the disadvantages of the conventional navigation computation scheme,an improved computation scheme of the SINS using rotation technique is proposed which can reduce the effects of the rotation platform errors.And,the error characteristics of the SINS with this navigation computation scheme are analyzed.Theoretical analysis,simulations and real test results show that the proposed navigation computation scheme outperforms the conventional navigation computation scheme,meanwhile reduces the requirement to the measurement accuracy of rotation angles.展开更多
Based on the upper bound theorem of limit analysis,the factor of safety for shallow tunnel in saturated soil is calculated in conjunction with the strength reduction technique.To analyze the influence of the pore pres...Based on the upper bound theorem of limit analysis,the factor of safety for shallow tunnel in saturated soil is calculated in conjunction with the strength reduction technique.To analyze the influence of the pore pressure on the factor of safety for shallow tunnel,the power of pore pressure is regarded as a power of external force in the energy calculation.Using the rigid multiple-block failure mechanism,the objective function for the factor of safety is constructed and the optimal solutions are derived by employing the sequential quadratic programming.According to the results of optimization calculation,the factor of safety of shallow tunnel for different pore pressure coefficients and variational groundwater tables are obtained.The parameter analysis shows that the pore pressure coefficient and the location of the groundwater table have significant influence on the factor of safety for shallow tunnel.展开更多
Based on the distribution characteristic of magnetic field along the polish wheel,the four-axis linkage technique is advanced to replace a standard five-axis one to figure low-gradient optical surfaces with a raster t...Based on the distribution characteristic of magnetic field along the polish wheel,the four-axis linkage technique is advanced to replace a standard five-axis one to figure low-gradient optical surfaces with a raster tool-path in magnetorheological finishing(MRF).After introducing the fundaments of such simplification,the figuring reachability of a four-axis system for the low-gradient optics was theoretically analyzed.Further validation including magnetic field intensity and influence function characteristic was performed to establish its application.To demonstrate the correctness,feasibility and applicability of such technique,a K4 spherical part was figured by two iterations of MRF with surface form error improved to 0.219λPV and 0.027λRMS.Meanwhile,the surface roughness was also improved a lot in MRF process.These theoretical analyses and experimental results both indicate that high form accuracy and excellent surface quality can be obtained by using the four-axis linkage technique in the process of figuring low-gradient optical elements,and the four-axis linkage system undoubtedly is much more easy to control and much more economical.展开更多
As a production quality index of hematite grinding process,particle size(PS)is hard to be measured in real time.To achieve the PS estimation,this paper proposes a novel data driven model of PS using stochastic configu...As a production quality index of hematite grinding process,particle size(PS)is hard to be measured in real time.To achieve the PS estimation,this paper proposes a novel data driven model of PS using stochastic configuration network(SCN)with robust technique,namely,robust SCN(RSCN).Firstly,this paper proves the universal approximation property of RSCN with weighted least squares technique.Secondly,three robust algorithms are presented by employing M-estimation with Huber loss function,M-estimation with interquartile range(IQR)and nonparametric kernel density estimation(NKDE)function respectively to set the penalty weight.Comparison experiments are first carried out based on the UCI standard data sets to verify the effectiveness of these methods,and then the data-driven PS model based on the robust algorithms are established and verified.Experimental results show that the RSCN has an excellent performance for the PS estimation.展开更多
Mining operation, especially underground coal mining, always has the remarkable risks of ground control. Passive seismic velocity tomography based on simultaneous iterative reconstructive technique （SIRT） inversion ...Mining operation, especially underground coal mining, always has the remarkable risks of ground control. Passive seismic velocity tomography based on simultaneous iterative reconstructive technique （SIRT） inversion is used to deduce the stress redistribution around the longwall mining panel. The mining-induced microseismic events were recorded by mounting an array of receivers on the surface, above the active panel. After processing and filtering the seismic data, the three-dimensional tomography images of the p-wave velocity variations by SIRT passive seismic velocity tomography were provided. To display the velocity changes on coal seam level and subsequently to infer the stress redistribution, these three-dimensional tomograms into the coal seam level were sliced. In addition, the boundary element method （BEM） was used to simulate the stress redistribution. The results show that the inferred stresses from the passive seismic tomograms are conformed to numerical models and theoretical concept of the stress redistribution around the longwall panel. In velocity tomograms, the main zones of the stress redistribution arotmd the panel, including front and side abutment pressures, and gob stress are obvious and also the movement of stress zones along the face advancement is evident. Moreover, the effect of the advance rate of the face on the stress redistribution is demonstrated in tomography images. The research result proves that the SIRT passive seismic velocity tomography has an ultimate potential for monitoring the changes of stress redistribution around the longwall mining panel continuously and subsequently to improve safety of mining operations.展开更多
Geosynthetic-reinforced and pile-supported （GRPS） embankment has been increasingly constructed in a large number of regions and for a wide range of projects in the past decades. However, many disadvantages are expos...Geosynthetic-reinforced and pile-supported （GRPS） embankment has been increasingly constructed in a large number of regions and for a wide range of projects in the past decades. However, many disadvantages are exposed through a lot of applications on conventional technique of GRPS embankment （called CT embankment）, i.e., intolerable settlement and lateral displacement, low geosynthetic efficiency, etc. In view of these disadvantages, the fixed geosynthetic technique of GRPS embankment （called FGT embankment） is developed in this work. In this system, the geosynthetic is fixed on the pile head by the steel bar fulcrum and concrete fixed top. The principles and construction techniques involved in the FGT embankment are described firstly. Then, the numerical analysis method and two-stage analysis method are used to study the performance of FGT embankment, respectively. It is shown that the FGT embankment can provide a better improvement technique to construct a high embankment over soft ground.展开更多
Multi-function,multiband,cost-effective,miniaturized reconfigurable radio frequency(RF)components are highly demanded in modern and future wireless communication systems.This paper discusses the needs and implementati...Multi-function,multiband,cost-effective,miniaturized reconfigurable radio frequency(RF)components are highly demanded in modern and future wireless communication systems.This paper discusses the needs and implementation of multiband reconfigurable RF components with microfabrication techniques and advanced materials.RF applications of fabrication methods such as surface and bulk micromachining techniques are reviewed,especially on the development of RF microelectromechanical systems(MEMS)and other tunable components.Works on the application of ferroelectric and ferromagnetic materials are investigated,which enables RF components with continuous tunability,reduced size,and enhanced performance.Methods and strategies with nano-patterning to improve high frequency characteristics of ferromagnetic thin film(e.g.,ferromagnetic resonance frequency and losses)and their applications on the development of fully electrically tunable RF components are fully demonstrated.展开更多
A method combining the pseudo-dynamic approach and discretization technique is carried out for computing the active earth pressure.Instead of using a presupposed failure mechanism,discretization technique is introduce...A method combining the pseudo-dynamic approach and discretization technique is carried out for computing the active earth pressure.Instead of using a presupposed failure mechanism,discretization technique is introduced to generate the potential failure surface,which is applicable to the case that soil strength parameters have spatial variability.For the purpose of analyzing the effect of earthquake,pseudo-dynamic approach is adopted to introduce the seismic forces,which can take into account the dynamic properties of seismic acceleration.A new type of micro-element is used to calculate the rate of work of external forces and the rate of internal energy dissipation.The analytical expression of seismic active earth pressure coefficient is deduced in the light of upper bound theorem and the corresponding upper bound solutions are obtained through numerical optimization.The method is validated by comparing the results of this paper with those reported in literatures.The parametric analysis is finally presented to further expound the effect of diverse parameters on active earth pressure under non-uniform soil.展开更多
Multivariate statistical techniques,such as cluster analysis(CA),discriminant analysis(DA),principal component analysis(PCA) and factor analysis(FA),were applied to evaluate and interpret the surface water quality dat...Multivariate statistical techniques,such as cluster analysis(CA),discriminant analysis(DA),principal component analysis(PCA) and factor analysis(FA),were applied to evaluate and interpret the surface water quality data sets of the Second Songhua River(SSHR) basin in China,obtained during two years(2012-2013) of monitoring of 10 physicochemical parameters at 15 different sites.The results showed that most of physicochemical parameters varied significantly among the sampling sites.Three significant groups,highly polluted(HP),moderately polluted(MP) and less polluted(LP),of sampling sites were obtained through Hierarchical agglomerative CA on the basis of similarity of water quality characteristics.DA identified p H,F,DO,NH3-N,COD and VPhs were the most important parameters contributing to spatial variations of surface water quality.However,DA did not give a considerable data reduction(40% reduction).PCA/FA resulted in three,three and four latent factors explaining 70%,62% and 71% of the total variance in water quality data sets of HP,MP and LP regions,respectively.FA revealed that the SSHR water chemistry was strongly affected by anthropogenic activities(point sources:industrial effluents and wastewater treatment plants;non-point sources:domestic sewage,livestock operations and agricultural activities) and natural processes(seasonal effect,and natural inputs).PCA/FA in the whole basin showed the best results for data reduction because it used only two parameters(about 80% reduction) as the most important parameters to explain 72% of the data variation.Thus,this work illustrated the utility of multivariate statistical techniques for analysis and interpretation of datasets and,in water quality assessment,identification of pollution sources/factors and understanding spatial variations in water quality for effective stream water quality management.展开更多
For solving the difficult problem of leakage detection in city gas pipelines, a method using acoustic technique based on instantaneous energy (IE) distribution and correlation analysis was proposed. Firstly, the basic...For solving the difficult problem of leakage detection in city gas pipelines, a method using acoustic technique based on instantaneous energy (IE) distribution and correlation analysis was proposed. Firstly, the basic theory of leakage detection and location was introduced. Then the physical relationship between instantaneous energy and structural state variation of a system was analyzed theoretically. With HILBERT-HUANG transformation (HHT), the instantaneous energy distribution feature of an unstable acoustic signal was obtained. According to the relative contribution method of the instantaneous energy, the noise in signal was eliminated effectively. Furthermore, in order to judge the leakage, the typical characteristic of the instantaneous energy of signal in the input and output end was discussed using correlative analysis. A number of experiments were carried out to classify the leakage from normal operations, and the results show that the leakages are successfully detected and the average recognition rate reaches 93.3% among three group samples. It is shown that the method using acoustic technique with IED and correlative analysis is effective and it may be referred in other pipelines.展开更多
A CMOS active mixer based on voltage control load technique which can operate at 1.0 V supply voltage was proposed, and its operation principle, noise and linearity analysis were also presented. Contrary to the conven...A CMOS active mixer based on voltage control load technique which can operate at 1.0 V supply voltage was proposed, and its operation principle, noise and linearity analysis were also presented. Contrary to the conventional Gilbert-type mixer which is based on RF current-commutating, the load impedance in this proposed mixer is controlled by the LO signal, and it has only two stacked transistors at each branch which is suitable for low voltage applications. The mixer was designed and fabricated in 0.18 tam CMOS process for 2.4 GHz ISM band applications. With an input of 2.44 GHz RF signal and 2.442 GHz LO signal, the measurement specifications of the proposed mixer are： the conversion gain （Gc） is 5.3 dB, the input-referred third-order intercept point （PIIP3） is 4.6 dBm, the input-referred 1 dB compression point （P1dB） is --7.4 dBm, and the single-sideband noise figure （NFSSB） is 21.7 dB.展开更多
A nano-displacement measurement system with duo-gratings is analyzed by using optics theory,a math- ematic model for the system is established,and the characteristic of laser Moirésignals is studied through CAD s...A nano-displacement measurement system with duo-gratings is analyzed by using optics theory,a math- ematic model for the system is established,and the characteristic of laser Moirésignals is studied through CAD simu- lation.To improve signal sensitivity and positioning accuracy,two methods of precision positioning are brought for- ward:differential Moirépositioning method and modified Moirépositioning method.A compound control system for precision positioning is set up by combining these 2 Moiréalignment methods,in which the modified Moiréalignment technique is used for coarse alignment and the differential Moiréalignment technique is used for fine alignment,and the system obtains positioning accuracy of±10 nm in±500μm positioning range with shot response time.展开更多
A new coastal technique, named as assembly coastal building, was introduced. The main concept of the technique was the assembling components which could be combined and locked together to form a large caisson. The ass...A new coastal technique, named as assembly coastal building, was introduced. The main concept of the technique was the assembling components which could be combined and locked together to form a large caisson. The assembly coastal building technique was used in a sea access road in Zhuanghai 4X1 well, Dagang Oilfield. The design plans and in-situ tests in the sea access road project were introduced in detail. According to the Zhuanghai project, the numerical simulation method of assembly coastal building technique was proposed. 2D numerical simulations were performed in FLAC to analyze the displacement and stability of the technique in the construction process and post-construction period. The settlement calculated is close to the in-situ results, which proves that the proposed numerical method is reasonable. Results show that the assembly coastal building technique has large safety factor under the gravity loading and wave loadings.展开更多
According to the production index of lint cotton yield over 100kg per mu(1/15ha)and the relationship between the climate factors and the distribution of time and space for cottonboll setting in 1985—1990,we establish...According to the production index of lint cotton yield over 100kg per mu(1/15ha)and the relationship between the climate factors and the distribution of time and space for cottonboll setting in 1985—1990,we established a model of cultural techniques of cotton leaf-age-ad-justing-controlling for enhancing early maturity.By utilizing the principle of leaf-age model andthe principle of regulating nutrient distribution with DPC(Mepiquate chloride),the plants weretreated with DPC in proper time.A new type of population plant patterns was set up.It character-ized by high population density,dwarf,high boll weight,bolls near nodes,high energy and lowconsumption,short distance transport of nutrients,high yield and good quality.We put forward aset of management measures,i.e.adjusting boll setting stage,adjusting and controlling boll set-ting structure,stably applying N,increasing P,supplementing plants with K,increasing irrigationefficiency,techniques were applied and demonstrated in large areas in high yield展开更多
基金Supported by the National Natural Science Foundation of China(42474239,41204128)China National Space Administration(Pre-research project on Civil Aerospace Technologies No.D010301)Strategic Priority Research Program of the Chinese Academy of Sciences(XDA17010303)。
文摘One of the detection objectives of the Chinese Asteroid Exploration mission is to investigate the space environment near the Main-belt Comet(MBC,Active Asteroid)311P/PANSTARRS.This paper outlines the scientific objectives,measurement targets,and measurement requirements for the proposed Gas and Ion Analyzer(GIA).The GIA is designed for in-situ mass spectrometry of neutral gases and low-energy ions,such as hydrogen,carbon,and oxygen,in the vicinity of 311P.Ion sampling techniques are essential for the GIA's Time-of-Flight(TOF)mass analysis capabilities.In this paper,we present an enhanced ion sampling technique through the development of an ion attraction model and an ion source model.The ion attraction model demonstrates that adjusting attraction grid voltage can enhance the detection efficiency of low-energy ions and mitigate the repulsive force of ions during sampling,which is influenced by the satellite's surface positive charging.The ion source model simulates the processes of gas ionization and ion multiplication.Simulation results indicate that the GIA can achieve a lower pressure limit below 10-13Pa and possess a dynamic range exceeding 10~9.These performances ensure the generation of ions with stable and consistent current,which is crucial for high-resolution and broad dynamic range mass spectrometer analysis.Preliminary testing experiments have verified GIA's capability to detect gas compositions such as H2O and N2.In-situ measurements near 311P using GIA are expected to significantly contribute to our understanding of asteroid activity mechanisms,the evolution of the atmospheric and ionized environments of main-belt comets,the interactions with solar wind,and the origin of Earth's water.
基金Supported by the Harbin Engineering University Fund for Basic Projects (heuft06041)
文摘The initial motivation of the lifting technique is to solve the H∞control problems. However, the conventional weighted H∞design does not meet the conditions required by lifting, so the result often leads to a misjudgement of the design. Two conditions required by using the lifting technique are presented based on the basic formulae of the lifting. It is pointed out that only the H∞disturbance attenuation problem with no weighting functions can meet these conditions, hence, the application of the lifting technique is quite limited.
基金supported by the National Natural Science Foundation of China(61174203)Aeronautical Science Foundation of China(20110177002)
文摘An agile missile with tail fins and pulse thrusters has continuous and discontinuous control inputs.This brings certain difficulty to the autopilot design and stability analysis.Indirect robust control via Theta-D technique is employed to handle this problem.An acceleration tracking system is formulated based on the nonlinear dynamics of agile missile.Considering the dynamics of actuators,there is an error between actual input and computed input.A robust control problem is formed by treating the error as input uncertainty.The robust control is equivalent to a nonlinear quadratic optimal control of the nominal system with a modified performance index including uncertainty bound.Theta-D technique is applied to solve the nonlinear optimal control problem to obtain the final control law.Numerical results show the effectiveness and robustness of the proposed strategy.
基金supported by the National Natural Science Foundation of China for Innovative Research Groups(70821001),the National Natural Science Foundation of China(70901069)the Special Fund for the Gainers of Excellent Ph.D.'s Dissertations and Dean's Scholarships of Chinese Academy of Sciences,the Research Fund for the Doctoral Program of Higher Education of China for New Teachers(20093402120013)+1 种基金the Research Fund for the Excellent Youth Scholars of Higher School of Anhui Province of China(2010SQRW001ZD)the Social Science Research Fund for Higher School of Anhui Province of China
文摘The cross-efficiency evaluation method is reviewed which is developed as a data envelopment analysis （DEA） extensive tool. The cross-efficiency evaluation method is utilized to identify the decision making unit （DMU） with the best practice and to rank the DMUs by their respective cross-efficiency scores. The main drawbacks of the cross-efficiency evaluation method when the ultimate average cross-efficiency scores are used to evalu- ate and rank the DMUs are also pointed out. With the research gap, an improved technique for order preference by similarity to ideal solution （TOPSIS） is introduced to rank the crossfficiency by eliminating the average assumption. Finally, an empirical example is illustrated to examine the validity of the proposed method.
基金Projects(2013CB0360042011CB013800)supported by the National Basic Research Program of China+1 种基金Project(51178468)supported by the National Natural Science Foundation of ChinaProject(2011G013-B)supported by the Science and Technology Development of Railways Department in China
文摘Based on the nonlinear failure criterion and the upper bound theorem, the modified tangential technique method was proposed to derive the expression of supporting pressure acting on shallow tunnel. Instead of the same stress state, different normal stresses on element boundaries were used. In order to investigate the influence of different factors on supporting pressures, the failure mechanism was established. The solution of supporting pressure, with different parameters, was obtained by optimization theory. The corresponding failure mechanism and numerical results were presented. In comparison with the results using the single tangential technique method, it is found that the proposed method is effective, and the good agreement shows that the present solution of supporting pressure is reliable.
基金Projects(51074014,51174014) supported by the National Natural Science Foundation of China
文摘Methods that can efficiently model the effects of rock joints on rock mass behavior can be beneficial in rock engineering. The suitability of equivalent rock mass(ERM) technique based upon particle methods is investigated. The ERM methodology is first validated by comparing calculated and experimental data of lab triaxial compression test on a set of cylindrical rock mass samples, each containing a single joint oriented in various dip angles. The simulated results are then used to study the stress-strain nonlinearity and failure mechanism as a function of the joint dip angle and confining stress. The anisotropy and size effects are also investigated by using multi-scale cubic ERM models subjected to triaxial compression test. The deformation and failure behavior are found to be influenced by joint degradation, the micro-crack formation in the intact rock, the interaction between two joints, and the interactions of micro-cracks and joints.
基金Project(60604011) supported by the National Natural Science Foundation of China
文摘To improve the accuracy of strapdown inertial navigation system(SINS) for long term applications,the rotation technique is employed to modulate the errors of the inertial sensors into periodically varied signals,and,as a result,to suppress the divergence of SINS errors.However,the errors of rotation platform will be introduced into SINS and might affect the final navigation accuracy.Considering the disadvantages of the conventional navigation computation scheme,an improved computation scheme of the SINS using rotation technique is proposed which can reduce the effects of the rotation platform errors.And,the error characteristics of the SINS with this navigation computation scheme are analyzed.Theoretical analysis,simulations and real test results show that the proposed navigation computation scheme outperforms the conventional navigation computation scheme,meanwhile reduces the requirement to the measurement accuracy of rotation angles.
基金Project(51178468) supported by the National Natural Science Foundation of ChinaProject(2010bsxt07) supported by the Doctoral Dissertation Innovation Fund of Central South University,China
文摘Based on the upper bound theorem of limit analysis,the factor of safety for shallow tunnel in saturated soil is calculated in conjunction with the strength reduction technique.To analyze the influence of the pore pressure on the factor of safety for shallow tunnel,the power of pore pressure is regarded as a power of external force in the energy calculation.Using the rigid multiple-block failure mechanism,the objective function for the factor of safety is constructed and the optimal solutions are derived by employing the sequential quadratic programming.According to the results of optimization calculation,the factor of safety of shallow tunnel for different pore pressure coefficients and variational groundwater tables are obtained.The parameter analysis shows that the pore pressure coefficient and the location of the groundwater table have significant influence on the factor of safety for shallow tunnel.
基金Project(91023042)supported by the National Natural Science Foundation of ChinaProject(2011CB013200)supported by the National Basic Research Program of China+1 种基金Project(B090302)supported by the Fund of Innovation,Graduate School of National University of Defense Technology,ChinaProject(CX2009B004)supported by the Hunan Provincial Innovation Foundation for Postgraduate,China
文摘Based on the distribution characteristic of magnetic field along the polish wheel,the four-axis linkage technique is advanced to replace a standard five-axis one to figure low-gradient optical surfaces with a raster tool-path in magnetorheological finishing(MRF).After introducing the fundaments of such simplification,the figuring reachability of a four-axis system for the low-gradient optics was theoretically analyzed.Further validation including magnetic field intensity and influence function characteristic was performed to establish its application.To demonstrate the correctness,feasibility and applicability of such technique,a K4 spherical part was figured by two iterations of MRF with surface form error improved to 0.219λPV and 0.027λRMS.Meanwhile,the surface roughness was also improved a lot in MRF process.These theoretical analyses and experimental results both indicate that high form accuracy and excellent surface quality can be obtained by using the four-axis linkage technique in the process of figuring low-gradient optical elements,and the four-axis linkage system undoubtedly is much more easy to control and much more economical.
基金Projects(61603393,61741318)supported in part by the National Natural Science Foundation of ChinaProject(BK20160275)supported by the Natural Science Foundation of Jiangsu Province,China+1 种基金Project(2015M581885)supported by the Postdoctoral Science Foundation of ChinaProject(PAL-N201706)supported by the Open Project Foundation of State Key Laboratory of Synthetical Automation for Process Industries of Northeastern University,China
文摘As a production quality index of hematite grinding process,particle size(PS)is hard to be measured in real time.To achieve the PS estimation,this paper proposes a novel data driven model of PS using stochastic configuration network(SCN)with robust technique,namely,robust SCN(RSCN).Firstly,this paper proves the universal approximation property of RSCN with weighted least squares technique.Secondly,three robust algorithms are presented by employing M-estimation with Huber loss function,M-estimation with interquartile range(IQR)and nonparametric kernel density estimation(NKDE)function respectively to set the penalty weight.Comparison experiments are first carried out based on the UCI standard data sets to verify the effectiveness of these methods,and then the data-driven PS model based on the robust algorithms are established and verified.Experimental results show that the RSCN has an excellent performance for the PS estimation.
文摘Mining operation, especially underground coal mining, always has the remarkable risks of ground control. Passive seismic velocity tomography based on simultaneous iterative reconstructive technique （SIRT） inversion is used to deduce the stress redistribution around the longwall mining panel. The mining-induced microseismic events were recorded by mounting an array of receivers on the surface, above the active panel. After processing and filtering the seismic data, the three-dimensional tomography images of the p-wave velocity variations by SIRT passive seismic velocity tomography were provided. To display the velocity changes on coal seam level and subsequently to infer the stress redistribution, these three-dimensional tomograms into the coal seam level were sliced. In addition, the boundary element method （BEM） was used to simulate the stress redistribution. The results show that the inferred stresses from the passive seismic tomograms are conformed to numerical models and theoretical concept of the stress redistribution around the longwall panel. In velocity tomograms, the main zones of the stress redistribution arotmd the panel, including front and side abutment pressures, and gob stress are obvious and also the movement of stress zones along the face advancement is evident. Moreover, the effect of the advance rate of the face on the stress redistribution is demonstrated in tomography images. The research result proves that the SIRT passive seismic velocity tomography has an ultimate potential for monitoring the changes of stress redistribution around the longwall mining panel continuously and subsequently to improve safety of mining operations.
基金Foundation item： Project（51278216） supported by the National Natural Science Foundation of China Project（11-2-05） supported by the Scientific and Technological Project for Shanxi Communication Construction, China Project（HF-08-01-2011-240） supported by the Graduates＇ Innovation Fund of Huazhong University of Science and Technology, China
文摘Geosynthetic-reinforced and pile-supported （GRPS） embankment has been increasingly constructed in a large number of regions and for a wide range of projects in the past decades. However, many disadvantages are exposed through a lot of applications on conventional technique of GRPS embankment （called CT embankment）, i.e., intolerable settlement and lateral displacement, low geosynthetic efficiency, etc. In view of these disadvantages, the fixed geosynthetic technique of GRPS embankment （called FGT embankment） is developed in this work. In this system, the geosynthetic is fixed on the pile head by the steel bar fulcrum and concrete fixed top. The principles and construction techniques involved in the FGT embankment are described firstly. Then, the numerical analysis method and two-stage analysis method are used to study the performance of FGT embankment, respectively. It is shown that the FGT embankment can provide a better improvement technique to construct a high embankment over soft ground.
基金Projects(1253929,1910853)supported by the National Natural Science Foundation of China。
文摘Multi-function,multiband,cost-effective,miniaturized reconfigurable radio frequency(RF)components are highly demanded in modern and future wireless communication systems.This paper discusses the needs and implementation of multiband reconfigurable RF components with microfabrication techniques and advanced materials.RF applications of fabrication methods such as surface and bulk micromachining techniques are reviewed,especially on the development of RF microelectromechanical systems(MEMS)and other tunable components.Works on the application of ferroelectric and ferromagnetic materials are investigated,which enables RF components with continuous tunability,reduced size,and enhanced performance.Methods and strategies with nano-patterning to improve high frequency characteristics of ferromagnetic thin film(e.g.,ferromagnetic resonance frequency and losses)and their applications on the development of fully electrically tunable RF components are fully demonstrated.
基金Projects(51908557,51378510)supported by the National Natural Science Foundation of China。
文摘A method combining the pseudo-dynamic approach and discretization technique is carried out for computing the active earth pressure.Instead of using a presupposed failure mechanism,discretization technique is introduced to generate the potential failure surface,which is applicable to the case that soil strength parameters have spatial variability.For the purpose of analyzing the effect of earthquake,pseudo-dynamic approach is adopted to introduce the seismic forces,which can take into account the dynamic properties of seismic acceleration.A new type of micro-element is used to calculate the rate of work of external forces and the rate of internal energy dissipation.The analytical expression of seismic active earth pressure coefficient is deduced in the light of upper bound theorem and the corresponding upper bound solutions are obtained through numerical optimization.The method is validated by comparing the results of this paper with those reported in literatures.The parametric analysis is finally presented to further expound the effect of diverse parameters on active earth pressure under non-uniform soil.
基金Project (2012ZX07501002-001) supported by the Ministry of Science and Technology of China
文摘Multivariate statistical techniques,such as cluster analysis(CA),discriminant analysis(DA),principal component analysis(PCA) and factor analysis(FA),were applied to evaluate and interpret the surface water quality data sets of the Second Songhua River(SSHR) basin in China,obtained during two years(2012-2013) of monitoring of 10 physicochemical parameters at 15 different sites.The results showed that most of physicochemical parameters varied significantly among the sampling sites.Three significant groups,highly polluted(HP),moderately polluted(MP) and less polluted(LP),of sampling sites were obtained through Hierarchical agglomerative CA on the basis of similarity of water quality characteristics.DA identified p H,F,DO,NH3-N,COD and VPhs were the most important parameters contributing to spatial variations of surface water quality.However,DA did not give a considerable data reduction(40% reduction).PCA/FA resulted in three,three and four latent factors explaining 70%,62% and 71% of the total variance in water quality data sets of HP,MP and LP regions,respectively.FA revealed that the SSHR water chemistry was strongly affected by anthropogenic activities(point sources:industrial effluents and wastewater treatment plants;non-point sources:domestic sewage,livestock operations and agricultural activities) and natural processes(seasonal effect,and natural inputs).PCA/FA in the whole basin showed the best results for data reduction because it used only two parameters(about 80% reduction) as the most important parameters to explain 72% of the data variation.Thus,this work illustrated the utility of multivariate statistical techniques for analysis and interpretation of datasets and,in water quality assessment,identification of pollution sources/factors and understanding spatial variations in water quality for effective stream water quality management.
基金Project(51004005) supported by the National Natural Science Foundation of ChinaProject supported by Open Research Fund Program of Beijing Engineering Research Center of Monitoring for Construction Safety (Beijing University of Civil Engineering and Architecture), China
文摘For solving the difficult problem of leakage detection in city gas pipelines, a method using acoustic technique based on instantaneous energy (IE) distribution and correlation analysis was proposed. Firstly, the basic theory of leakage detection and location was introduced. Then the physical relationship between instantaneous energy and structural state variation of a system was analyzed theoretically. With HILBERT-HUANG transformation (HHT), the instantaneous energy distribution feature of an unstable acoustic signal was obtained. According to the relative contribution method of the instantaneous energy, the noise in signal was eliminated effectively. Furthermore, in order to judge the leakage, the typical characteristic of the instantaneous energy of signal in the input and output end was discussed using correlative analysis. A number of experiments were carried out to classify the leakage from normal operations, and the results show that the leakages are successfully detected and the average recognition rate reaches 93.3% among three group samples. It is shown that the method using acoustic technique with IED and correlative analysis is effective and it may be referred in other pipelines.
基金Project(61166004) supported by the National Natural Science Foundation of ChinaProject(09ZCGHHZ00200) supported by the International Scientific and Technological Cooperation Program of Science and Technology Plan of Tianjin,ChinaProject(UF10028Y)supported by the Doctoral Scientific Research Foundation for Guilin University of Electronic Technology,China
文摘A CMOS active mixer based on voltage control load technique which can operate at 1.0 V supply voltage was proposed, and its operation principle, noise and linearity analysis were also presented. Contrary to the conventional Gilbert-type mixer which is based on RF current-commutating, the load impedance in this proposed mixer is controlled by the LO signal, and it has only two stacked transistors at each branch which is suitable for low voltage applications. The mixer was designed and fabricated in 0.18 tam CMOS process for 2.4 GHz ISM band applications. With an input of 2.44 GHz RF signal and 2.442 GHz LO signal, the measurement specifications of the proposed mixer are： the conversion gain （Gc） is 5.3 dB, the input-referred third-order intercept point （PIIP3） is 4.6 dBm, the input-referred 1 dB compression point （P1dB） is --7.4 dBm, and the single-sideband noise figure （NFSSB） is 21.7 dB.
基金Supported by the National High Technology Research and Development Program of China(863 Program)(2005AA303610)
文摘A nano-displacement measurement system with duo-gratings is analyzed by using optics theory,a math- ematic model for the system is established,and the characteristic of laser Moirésignals is studied through CAD simu- lation.To improve signal sensitivity and positioning accuracy,two methods of precision positioning are brought for- ward:differential Moirépositioning method and modified Moirépositioning method.A compound control system for precision positioning is set up by combining these 2 Moiréalignment methods,in which the modified Moiréalignment technique is used for coarse alignment and the differential Moiréalignment technique is used for fine alignment,and the system obtains positioning accuracy of±10 nm in±500μm positioning range with shot response time.
基金Project (50639010) supported by the National Natural Science Foundation of China
文摘A new coastal technique, named as assembly coastal building, was introduced. The main concept of the technique was the assembling components which could be combined and locked together to form a large caisson. The assembly coastal building technique was used in a sea access road in Zhuanghai 4X1 well, Dagang Oilfield. The design plans and in-situ tests in the sea access road project were introduced in detail. According to the Zhuanghai project, the numerical simulation method of assembly coastal building technique was proposed. 2D numerical simulations were performed in FLAC to analyze the displacement and stability of the technique in the construction process and post-construction period. The settlement calculated is close to the in-situ results, which proves that the proposed numerical method is reasonable. Results show that the assembly coastal building technique has large safety factor under the gravity loading and wave loadings.
文摘According to the production index of lint cotton yield over 100kg per mu(1/15ha)and the relationship between the climate factors and the distribution of time and space for cottonboll setting in 1985—1990,we established a model of cultural techniques of cotton leaf-age-ad-justing-controlling for enhancing early maturity.By utilizing the principle of leaf-age model andthe principle of regulating nutrient distribution with DPC(Mepiquate chloride),the plants weretreated with DPC in proper time.A new type of population plant patterns was set up.It character-ized by high population density,dwarf,high boll weight,bolls near nodes,high energy and lowconsumption,short distance transport of nutrients,high yield and good quality.We put forward aset of management measures,i.e.adjusting boll setting stage,adjusting and controlling boll set-ting structure,stably applying N,increasing P,supplementing plants with K,increasing irrigationefficiency,techniques were applied and demonstrated in large areas in high yield
