Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performa...Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performance all-solid-state lithium metal batteries.In this article,a novel sandwich structured solid-state PEO composite electrolyte is developed for high performance all-solid-state lithium metal batteries.The PEO-based composite electrolyte is fabricated by hot-pressing PEO,LiTFSI and Ti_(3)C_(2)T_(x) MXene nanosheets into glass fiber cloth(GFC).The as-prepared GFC@PEO-MXene electrolyte shows high mechanical properties,good electrochemical stability,and high lithium-ion migration number,which indicates an obvious synergistic effect from the microscale GFC and the nanoscale MXene.Such as,the GFC@PEO-1 wt%MXene electrolyte shows a high tensile strength of 43.43 MPa and an impressive Young's modulus of 496 MPa,which are increased by 1205%and 6048%over those of PEO.Meanwhile,the ionic conductivity of GFC@PEO-1 wt%MXene at 60℃ reaches 5.01×10^(-2) S m^(-1),which is increased by around 200%compared with that of GFC@PEO electrolyte.In addition,the Li/Li symmetric battery based on GFC@PEO-1 wt%MXene electrolyte shows an excellent cycling stability over 800 h(0.3 mA cm^(-2),0.3 mAh cm^(-2)),which is obviously longer than that based on PEO and GFC@PEO electrolytes due to the better compatibility of GFC@PEO-1 wt%MXene electrolyte with Li anode.Furthermore,the solid-state Li/LiFePO_(4) battery with GFC@PEO-1 wt%MXene as electrolyte demonstrates a high capacity of 110.2–166.1 mAh g^(-1) in a wide temperature range of 25–60C,and an excellent capacity retention rate.The developed sandwich structured GFC@PEO-1 wt%MXene electrolyte with the excellent overall performance is promising for next generation high performance all-solid-state lithium metal batteries.展开更多
Graphene oxide(GO)is regarded as a promising candidate to construct solar absorbers for addressing freshwater crisis,but the easy delamination of GO in water poses a critical challenge for practical solar desalination...Graphene oxide(GO)is regarded as a promising candidate to construct solar absorbers for addressing freshwater crisis,but the easy delamination of GO in water poses a critical challenge for practical solar desalination.Herein,we improve the stability of GO membranes by a self-crosslinking poly(ionic liquid)(PIL)in a mild condition,which crosslinks neighbouring GO nanosheets without blemishing the hydrophilic structure of GO.By further adding carbon nanotubes(CNTs),the sandwiched GO/CNT@PIL(GCP)membrane displays a good stability in pH=1 or 13 solution even for 270 days.The molecular dynamics simulation results indicate that the generation of water nanofluidics in nanochannels of GO nanosheets remarkably reduces the water evaporation enthalpy in GCP membrane,compared to bulk water.Consequently,the GCP membrane exhibits a high evaporation rate(1.87 kg m^(-2)h^(-1))and displays stable evaporation rates for 14 h under 1 kW m^(-2)irradiation.The GCP membrane additionally works very well when using different water sources(e.g.,dye-polluted water)or even strong acidic solution(pH=1)or basic solution(pH=13).More importantly,through bundling pluralities of GCP membrane,an efficient solar desalination device is developed to produce drinkable water from seawater.The average daily drinkable water amount in sunny day is 10.1 kg m^(-2),which meets with the daily drinkable water needs of five adults.The high evaporation rate,long-time durability and good scalability make the GCP membrane an outstanding candidate for practical solar seawater desalination.展开更多
In this paper,blend membranes from polyvinyl acetate(PVAc)and block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074)are prepared by solution casting and solvent evaporation method.Although they are homogeneous on ...In this paper,blend membranes from polyvinyl acetate(PVAc)and block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074)are prepared by solution casting and solvent evaporation method.Although they are homogeneous on a macro-scale,the observations from DSC and SEM indicate micro-phase separation for PVAc/Pebax1074 blend membranes.With the increase of Pebax1074 content,gas permeabilities of CO2,H2,N2and CH4all increase greatly.PVAc/Pebax1074 blend membranes with high PVAc content are appropriate for CO2/CH4separation.The temperature dependence of gas permeability is divided into rubbery region and glassy region.The activation energies of permeation in rubbery region are smaller than those in glassy region,and they all decrease with increasing Pebax1074 content.For N2,H2and CH4,their gas permeation properties are mainly influenced by the dual-mode sorption and hydrostatic pressure effect.But for CO2,its permeability increases with the increase of pressure due to CO2-induced plasticization effect,which is more obvious for PVAc/Pebax1074 blend membranes with high PVAc content.展开更多
Poly（amide-6-b-ethylene oxide）（Pebax1657）/1-butyl-3-methylimidazo-lium bis[trifluoromethyl）sulfonyl]-imide（[Bmim][Tf2N]） blend membranes with different [Bmim][Tf2N] contents were prepared via solution casting a...Poly（amide-6-b-ethylene oxide）（Pebax1657）/1-butyl-3-methylimidazo-lium bis[trifluoromethyl）sulfonyl]-imide（[Bmim][Tf2N]） blend membranes with different [Bmim][Tf2N] contents were prepared via solution casting and solvent evaporation method. The permeation properties of the blend membranes for CO2, N2,CH4 and H2 were studied, and the physical properties were characterized by differential scanning calorimeter（DSC） and X-ray diffraction（XRD）. Results showed that [Bmim][Tf2N] was dispersed as amorphous phase in the blend membranes, which caused the decrease of Tg（PE） and crystallinity（PA）. With the addition of [Bmim][Tf2N], the CO2 permeability increased and reached up to approximately 286 Barrer at 40 wt%[Bmim][Tf2N], which was nearly double that of pristine Pebax1657 membrane. The increase of CO2 permeability may be attributed to high intrinsic permeability of [Bmim][Tf2N], the increase of fractional free of volume（FFV） and plasticization effect. However, the CO2 permeability reduced firstly when the [Bmim][Tf2N]content was below 10 wt%, which may be due to that the small ions of [Bmim][Tf2N] in the gap of polymer chain inhibited the flexibility of polymer chain; the interaction between Pebax1657 and [Bmim][Tf2N]decreased the content of EO units available for CO2 transport and led to a more compact structure. For Pebax1657/[Bmim][Tf2N] blend membranes, the permeabilities of N2, H2 and CH4decreased with the increase of feed pressure due to the hydrostatic pressure effect, while CO2 permeability increased with the increase of feed pressure for that the CO2-induced plasticization effect was stronger than hydrostatic pressure effect.展开更多
Poly(ethylene-oxide)(PEO)-based membranes have attracted much attention recently for CO2 separation because CO2 is highly soluble into PEO and shows high selectivity over other gases such as CH4 and N2.Unfortunately,t...Poly(ethylene-oxide)(PEO)-based membranes have attracted much attention recently for CO2 separation because CO2 is highly soluble into PEO and shows high selectivity over other gases such as CH4 and N2.Unfortunately,those membranes are not strong enough mechanically and highly crystalline,which hinders their broader applications for separation membranes.In this review discussions are made,as much in detail as possible,on the strategies to improve gas separation performance of PEO-based membranes.Some of techniques such as synthesis of graft copolymers that contain PEO,cross-linking of polymers and blending with long chains polymers contributed significantly to improvement of membrane.Incorporation of ionic liquids/nanoparticles has also been found effective.However,surface modification of nanoparticles has been done chemically or physically to enhance their compatibility with polymer matrix.As a result of all such efforts,an excellent performance,i.e.,CO2 permeability up to 200 Barrer,CO2/N2 selectivity up to 200 and CO2/CH4 selectivity up to 70,could be achieved.Another method is to introduce functional groups into PEO-based polymers which boosted CO2 permeability up to 200 Barrer with CO2/CH4 selectivity between 40 and 50.The CO2 permeability of PEO-based membranes increases,without much change in selectivity,when the length of ethylene oxide is increased.展开更多
Cell labeling with magnetic iron oxide nanoparticles(IONPs)is increasingly a routine approach in the cellbased cancer treatment.However,cell labeling with magnetic IONPs and their leading effects on the biological pro...Cell labeling with magnetic iron oxide nanoparticles(IONPs)is increasingly a routine approach in the cellbased cancer treatment.However,cell labeling with magnetic IONPs and their leading effects on the biological properties of human lung carcinoma cells remain scarcely reported.Therefore,in the present study the magnetic c-Fe2O3nanoparticles(MNPs)were firstly synthesized and surface-modified with cationic poly-L-lysine(PLL)to construct the PLL-MNPs,which were then used to magnetically label human A549 lung cancer cells.Cell viability and proliferation were evaluated with propidium iodide/fluorescein diacetate double staining and standard 3-(4,5-dimethylthiazol-2-diphenyl-tetrazolium)bromide assay,and the cytoskeleton was immunocytochemically stained.The cell cycle of the PLL-MNPlabeled A549 lung cancer cells was analyzed using flow cytometry.Apoptotic cells were fluorescently analyzed with nuclear-specific staining after the PLL-MNP labeling.The results showed that the constructed PLL-MNPs efficiently magnetically labeled A549 lung cancer cells and that,at low concentrations,labeling did not affect cellular viability,proliferation capability,cell cycle,and apoptosis.Furthermore,the cytoskeleton in the treated cells was detected intact in comparison with the untreated counterparts.However,the results also showed that at high concentration(400 lg m L-1),the PLL-MNPs would slightly impair cell viability,proliferation,cell cycle,and apoptosis and disrupt the cytoskeleton in the treated A549 lung cancer cells.Therefore,the present results indicated that the PLL-MNPs at adequate concentrations can be efficiently used for labeling A549 lung cancer cells and could be considered as a feasible approach for magnetic targeted anti-cancer drug/gene delivery,targeted diagnosis,and therapy in lung cancer treatment.展开更多
Membranes from block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074) and its blends with different molecular weight poly(ethylene glycol)(PEG)(200, 400, 600, 1500, 4600 and 8000) were prepared. The thermal proper...Membranes from block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074) and its blends with different molecular weight poly(ethylene glycol)(PEG)(200, 400, 600, 1500, 4600 and 8000) were prepared. The thermal properties and structures of Pebax1074/PEG blend membranes were characterized by DSC and SEM, and the gas permeation properties of CO_2 and N_2 were also investigated at different temperatures. For Pebax1074/PEG blend membranes with low molecular weight PEG(MW≤ 600), higher gas permeabilities than Pebax1074 were achieved. The permeability increased with the increase of PEG molecular weight. The addition of low molecular weight PEG resulted in decrease in activation energy of permeation. For Pebax1074/PEG blend membranes with high molecular weight PEG(MW≥ 1500), due to the melt of PEO phase crystals, the gas permeation properties of blend membranes were temperaturedependent, which could be divided into crystalline region, transition region and amorphous region according to two different transition temperatures. PEG molecular weight and operation temperature determined different gas permeation properties of Pebax1074/PEG blend membranes in three regions. The activation energies of permeation in crystalline region were larger than those in amorphous region.展开更多
A new process for preparing poly(phenylene sulfide amide, PPSA), which is by reaction of sulfur instead of sodium sulfide as S source with dichlorobenzamide (DCBA) and alkali in polar orga...A new process for preparing poly(phenylene sulfide amide, PPSA), which is by reaction of sulfur instead of sodium sulfide as S source with dichlorobenzamide (DCBA) and alkali in polar organic solvent at the atmospheric pressure (called sulfur solution route), is reported in the present paper. The influences of polymerization time, molar ratio of precursors, catalyst and solvent upon the polymer were investigated. To seek the best parameters of polymerization, orthogonal design was employed in the experiments. The results indicate that the molar ratio of precursors is the most significant effect on both of viscosity and yield of the polymer. The suitable parameters for preparing the related polymer are presented. The polymer was characterized by IRspectrum, 1HNMRspectrum and Raman spectrum, etc.展开更多
A ternary hybrid membrane architecture consisting of sulfonated fluorinated multi-block copolymer （SFMC）, sulfonated （poly ether ether ketone） （SPEEK） and I or 5 wt% graphene oxide （GO） was fabricated through ...A ternary hybrid membrane architecture consisting of sulfonated fluorinated multi-block copolymer （SFMC）, sulfonated （poly ether ether ketone） （SPEEK） and I or 5 wt% graphene oxide （GO） was fabricated through a facile solution casting approach. The simple, but effective monomer sulfonation was performed for SFMC to create compact and rigid hydrophobic backbone structures, while conventional random sulfonation was carried-out for SPEEK. Hydrophilic-hydrophobic-hydrophilic structure of SFMC enhances the compatibility with SPEEK and GO and allows for an unprecedented approach to alter me- chanical strength and proton conductivity of ternary hybrid membrane, as verified from universal test machine （UTM） curves and alternating current （AC） impedance plots. The impact of GO integration on the morphology and roughness of hybrid membrane was scrutinized using field emission scanning electron microscope （FE-SEM） and atomic force microscope （AFM）. Ternary hybrid showed uniform intercalation of GO nanosheets throughout the entire surface of membrane with an increased surface roughness of 8.91 nm. The constructed ternary hybrid membrane revealed excellent water absorption, ion exchange capacity and gas barrier properties, while retaining reasonable dimensional stability. The well-optimized ternary hybrid membrane containing 5 wt% GO revealed a maximum proton conductivity of 111.9 mS/cm, which is higher by a factor of two-fold with respect to that of bare SFMC membrane. The maximum PEMFC power density of 528.07mW/cm2 was yielded by ternary hybrid membrane at a load current density of 1321.1 mA/cm2 when operating the cell at 70 ℃ under 100% relative humidity （RH）. In comparison, a maximum power density of only 182.06 mW/cm2 was exhibited by the bare SFMC membrane at a load current density of 455.56 mA/cm2 under same operating conditions.展开更多
The drying of aqueous poly（ethylene oxide） （PEO） droplet on a substrate at different temperatures was studied. It was found that the contact line receded when the substrate was at a temperature above 60 ℃. Differ...The drying of aqueous poly（ethylene oxide） （PEO） droplet on a substrate at different temperatures was studied. It was found that the contact line receded when the substrate was at a temperature above 60 ℃. Different nucleation behavior and surface profiles of PEO films were found in different droplets drying processes. The rheological properties of aqueous PEO solutions were studied to understand the mechanism of contact line recession and micro-flow in drying aqueous PEO droplets. It was found that at low temperature, the contact line was static because of great viscous stress; while at high temperature, it receded because of great Marangoni force and the decrease of viscous stress. It was indicated that Marangoni convection was inhibited by the outward capillary flow and viscous stress at low temperature, whereas it became dominant at high temperature. Two types of mechanism for surface profiles and nucleation of PEO film from drying droplets are proposed, providing a theoretical guide for polymer solution application in oil and gas foam flooding technology.展开更多
Solid-state polymer electrolytes(SPEs)have attracted increasing attention due to good interfacial contact,light weight,and easy manufacturing.However,the practical application of SPEs such as the most widely studied p...Solid-state polymer electrolytes(SPEs)have attracted increasing attention due to good interfacial contact,light weight,and easy manufacturing.However,the practical application of SPEs such as the most widely studied poly(ethylene oxide)(PEO)in high-energy solid polymer batteries is still challenging,and the reasons are yet elusive.Here,it is found that the mismatch between PEO and 4.2 V-class cathodes is beyond the limited electrochemical window of PEO in the solid Li Ni_(1/3)Mn_(1/3)Co_(1/3)O_(2)(NMC)-PEO batteries.The initial oxidation of PEO initiates remarkable surface reconstruction of NMC grains in solid batteries that are different from the situation in liquid electrolytes.Well-aligned nanovoids are observed in NMC grains during the diffusion of surface reconstruction layers towards the bulk in solid batteries.The substantial interphasial degradation,therefore,blocks smooth Li+transport across the NMC-PEO interface and causes performance degradation.A thin yet effective Li F-containing protection layer on NMC can effectively stabilize the NMC-PEO interface with a greatly improved lifespan of NMC|PEO|Li batteries.This work deepens the understanding of degradations in high-voltage solid-state polymer batteries.展开更多
The interfacial instability of the poly(ethylene oxide)(PEO)-based electrolytes impedes the long-term cycling and further application of all-solid-state lithium metal batter-ies.In this work,we have shown an effective...The interfacial instability of the poly(ethylene oxide)(PEO)-based electrolytes impedes the long-term cycling and further application of all-solid-state lithium metal batter-ies.In this work,we have shown an effective additive 1-adaman-tanecarbonitrile,which con-tributes to the excellent per-formance of the poly(ethylene oxide)-based electrolytes.Owing to the strong interaction of the 1-Adamantanecarboni-trile to the polymer matrix and anions,the coordination of the Li^(+)-EO is weakened,and the binding effect of anions is strengthened,thereby improving the Li^(+)conductivity and the electrochemical stability.The diamond building block on the surface of the lithium anode can sup-press the growth of lithium dendrites.Importantly,the 1-Adamantanecarbonitrile also regulates the formation of LiF in the solid electrolyte interface and cathode electrolyte interface,which contributes to the interfacial stability(especially at high voltages)and protects the electrodes,enabling all-solid-state batteries to cycle at high voltages for long periods of time.Therefore,the Li/Li symmetric cell undergoes long-term lithium plating/stripping for more than 2000 h.1-Adamantanecarbonitrile-poly(ethylene oxide)-based LFP/Li and 4.3 V Ni_(0.8)Mn_(0.1)Co_(0.1)O_(2)/Li all-solid-state batteries achieved stable cycles for 1000 times,with capacity retention rates reaching 85%and 80%,respectively.展开更多
Poly(ethylene oxide)(PEO)and its derivatives based gel polymer electrolytes(GPEs)are severely limited in advanced and safe lithium-ion batteries(LIBs)owing to the intrinsically high flammability of liquid electrolytes...Poly(ethylene oxide)(PEO)and its derivatives based gel polymer electrolytes(GPEs)are severely limited in advanced and safe lithium-ion batteries(LIBs)owing to the intrinsically high flammability of liquid electrolytes and PEO.Directly adding flame retardants to the GPEs can suppress their flammability and thus improve the safety of LIBs,but results in deteriorative electrochemical performance.Herein,a novel GPE with chemically bonded flame retardant(i.e.diethyl vinylphosphonate)in cross-linked polyethylene glycol diacrylate matrix,featuring both high-safety and high-performance,is designed.This as-prepared GPE storing the commercial 1 mol L^(-1) LiPF6 electrolyte resists high temperature of 200℃and cannot be ignited as well as possesses a high ionic conductivity(0.60 m S cm^(-1))and good compatibility with lithium.Notably,the LiFePO_(4)/Li battery with this GPE delivers a satisfactory capacity of 142.2 m A h g^(-1) and a superior cycling performance with a capacity retention of 96.3%and a coulombic efficiency of close to 100%for 350 cycles at 0.2 C under ambient temperature.Furthermore,the battery can achieve steady charge–discharge for 100 cycles with a coulombic efficiency of 99.5%at 1 C under 80℃and run normally even at a high temperature of 150℃or under the exposure to butane flame.Differential scanning calorimetry manifests significantly improved battery safety compared to commercial battery systems.This work provides a new pathway for developing next-generation advanced LIBs with enhanced performance and high safety.展开更多
In this study,the precursor 4-(4-carboxy-phenoxy)phthalonitrile(CPPN)was first bonded onto the silica gel surface modified with poly(glycidyl methacrylate)(PGMA)(PGMA/SiO2)to prepare CPPN-PGMA/SiO2,and metal phthalocy...In this study,the precursor 4-(4-carboxy-phenoxy)phthalonitrile(CPPN)was first bonded onto the silica gel surface modified with poly(glycidyl methacrylate)(PGMA)(PGMA/SiO2)to prepare CPPN-PGMA/SiO2,and metal phthalocyanine(MPc;M=Co,Fe,Cu,Mn)was supported on the PGMA/SiO2 surface to prepare MPc-PGMA/SiO2 by synchronous synthesis and immobilization with phthalonitrile and metal salt in the solution.The chemical composition and surface morphology were characterized by the Fourier transform infrared(FTIR)spectroscopy,UV-Vis spectroscopy,scanning electron microscopy(SEM),X-ray photoelectron spectroscopy(XPS),and thermogravimetry analysis(TGA).The catalytic performance of MPc-PGMA/SiO2 in epoxidation of styrene was also investigated with molecular oxygen acting as the oxidant.The results show that MPc-PGMA/SiO2 can efficiently and selectively catalyze molecular oxygen for oxidation of styrene to styrene oxide under mild conditions.However,the catalytic activity differs substantially depending on the central metal,and a highest catalytic activity is achieved by CoPc-PGMA/SiO2.The CoPc-PGMA/SiO2 amount and temperature can also affect the catalytic oxidation of styrene,and at normal atmospheric pressure,a maximum conversion rate of styrene(99%)and selectivity of styrene oxide(53%)are obtained using 0.1 g of CoPc-PGMA/SiO2(22.61μmol of CoPc)at 100℃ for 6 h.CoPc-PGMA/SiO2 also has excellent reusability,and the conversion rate of styrene is still over 90%after 5 cycles.展开更多
基金support of the Fundamental Research Funds for the Central Universities(No.2022CDJQY-004)the Fund for Innovative Research Groups of Natural Science Foundation of Hebei Province(No.A2020202002).
文摘Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performance all-solid-state lithium metal batteries.In this article,a novel sandwich structured solid-state PEO composite electrolyte is developed for high performance all-solid-state lithium metal batteries.The PEO-based composite electrolyte is fabricated by hot-pressing PEO,LiTFSI and Ti_(3)C_(2)T_(x) MXene nanosheets into glass fiber cloth(GFC).The as-prepared GFC@PEO-MXene electrolyte shows high mechanical properties,good electrochemical stability,and high lithium-ion migration number,which indicates an obvious synergistic effect from the microscale GFC and the nanoscale MXene.Such as,the GFC@PEO-1 wt%MXene electrolyte shows a high tensile strength of 43.43 MPa and an impressive Young's modulus of 496 MPa,which are increased by 1205%and 6048%over those of PEO.Meanwhile,the ionic conductivity of GFC@PEO-1 wt%MXene at 60℃ reaches 5.01×10^(-2) S m^(-1),which is increased by around 200%compared with that of GFC@PEO electrolyte.In addition,the Li/Li symmetric battery based on GFC@PEO-1 wt%MXene electrolyte shows an excellent cycling stability over 800 h(0.3 mA cm^(-2),0.3 mAh cm^(-2)),which is obviously longer than that based on PEO and GFC@PEO electrolytes due to the better compatibility of GFC@PEO-1 wt%MXene electrolyte with Li anode.Furthermore,the solid-state Li/LiFePO_(4) battery with GFC@PEO-1 wt%MXene as electrolyte demonstrates a high capacity of 110.2–166.1 mAh g^(-1) in a wide temperature range of 25–60C,and an excellent capacity retention rate.The developed sandwich structured GFC@PEO-1 wt%MXene electrolyte with the excellent overall performance is promising for next generation high performance all-solid-state lithium metal batteries.
基金the financial support of the National Key R&D Program of China(No.2019YFC1806000)the Huazhong University of Science and Technology(No.3004013118)+2 种基金support from the National Natural Science Foundation of China(No.51903099)Huazhong University of Science and Technology(No.3004013134)the 100 Talents Program of the Hubei Provincial Government.Z.D.thanks the Postdoctoral Science Foundation of China(No.0106013063).
文摘Graphene oxide(GO)is regarded as a promising candidate to construct solar absorbers for addressing freshwater crisis,but the easy delamination of GO in water poses a critical challenge for practical solar desalination.Herein,we improve the stability of GO membranes by a self-crosslinking poly(ionic liquid)(PIL)in a mild condition,which crosslinks neighbouring GO nanosheets without blemishing the hydrophilic structure of GO.By further adding carbon nanotubes(CNTs),the sandwiched GO/CNT@PIL(GCP)membrane displays a good stability in pH=1 or 13 solution even for 270 days.The molecular dynamics simulation results indicate that the generation of water nanofluidics in nanochannels of GO nanosheets remarkably reduces the water evaporation enthalpy in GCP membrane,compared to bulk water.Consequently,the GCP membrane exhibits a high evaporation rate(1.87 kg m^(-2)h^(-1))and displays stable evaporation rates for 14 h under 1 kW m^(-2)irradiation.The GCP membrane additionally works very well when using different water sources(e.g.,dye-polluted water)or even strong acidic solution(pH=1)or basic solution(pH=13).More importantly,through bundling pluralities of GCP membrane,an efficient solar desalination device is developed to produce drinkable water from seawater.The average daily drinkable water amount in sunny day is 10.1 kg m^(-2),which meets with the daily drinkable water needs of five adults.The high evaporation rate,long-time durability and good scalability make the GCP membrane an outstanding candidate for practical solar seawater desalination.
基金supported by the National Science and Technology Planning Project (No.2011BAC08B00)the National High Technology Research and Development Program of China (863 Program)(No.2012AA03A611)
文摘In this paper,blend membranes from polyvinyl acetate(PVAc)and block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074)are prepared by solution casting and solvent evaporation method.Although they are homogeneous on a macro-scale,the observations from DSC and SEM indicate micro-phase separation for PVAc/Pebax1074 blend membranes.With the increase of Pebax1074 content,gas permeabilities of CO2,H2,N2and CH4all increase greatly.PVAc/Pebax1074 blend membranes with high PVAc content are appropriate for CO2/CH4separation.The temperature dependence of gas permeability is divided into rubbery region and glassy region.The activation energies of permeation in rubbery region are smaller than those in glassy region,and they all decrease with increasing Pebax1074 content.For N2,H2and CH4,their gas permeation properties are mainly influenced by the dual-mode sorption and hydrostatic pressure effect.But for CO2,its permeability increases with the increase of pressure due to CO2-induced plasticization effect,which is more obvious for PVAc/Pebax1074 blend membranes with high PVAc content.
基金supported by the National High Technology Research and Development Program of China(863 Program)(No.2012AA03A611)
文摘Poly（amide-6-b-ethylene oxide）（Pebax1657）/1-butyl-3-methylimidazo-lium bis[trifluoromethyl）sulfonyl]-imide（[Bmim][Tf2N]） blend membranes with different [Bmim][Tf2N] contents were prepared via solution casting and solvent evaporation method. The permeation properties of the blend membranes for CO2, N2,CH4 and H2 were studied, and the physical properties were characterized by differential scanning calorimeter（DSC） and X-ray diffraction（XRD）. Results showed that [Bmim][Tf2N] was dispersed as amorphous phase in the blend membranes, which caused the decrease of Tg（PE） and crystallinity（PA）. With the addition of [Bmim][Tf2N], the CO2 permeability increased and reached up to approximately 286 Barrer at 40 wt%[Bmim][Tf2N], which was nearly double that of pristine Pebax1657 membrane. The increase of CO2 permeability may be attributed to high intrinsic permeability of [Bmim][Tf2N], the increase of fractional free of volume（FFV） and plasticization effect. However, the CO2 permeability reduced firstly when the [Bmim][Tf2N]content was below 10 wt%, which may be due to that the small ions of [Bmim][Tf2N] in the gap of polymer chain inhibited the flexibility of polymer chain; the interaction between Pebax1657 and [Bmim][Tf2N]decreased the content of EO units available for CO2 transport and led to a more compact structure. For Pebax1657/[Bmim][Tf2N] blend membranes, the permeabilities of N2, H2 and CH4decreased with the increase of feed pressure due to the hydrostatic pressure effect, while CO2 permeability increased with the increase of feed pressure for that the CO2-induced plasticization effect was stronger than hydrostatic pressure effect.
文摘Poly(ethylene-oxide)(PEO)-based membranes have attracted much attention recently for CO2 separation because CO2 is highly soluble into PEO and shows high selectivity over other gases such as CH4 and N2.Unfortunately,those membranes are not strong enough mechanically and highly crystalline,which hinders their broader applications for separation membranes.In this review discussions are made,as much in detail as possible,on the strategies to improve gas separation performance of PEO-based membranes.Some of techniques such as synthesis of graft copolymers that contain PEO,cross-linking of polymers and blending with long chains polymers contributed significantly to improvement of membrane.Incorporation of ionic liquids/nanoparticles has also been found effective.However,surface modification of nanoparticles has been done chemically or physically to enhance their compatibility with polymer matrix.As a result of all such efforts,an excellent performance,i.e.,CO2 permeability up to 200 Barrer,CO2/N2 selectivity up to 200 and CO2/CH4 selectivity up to 70,could be achieved.Another method is to introduce functional groups into PEO-based polymers which boosted CO2 permeability up to 200 Barrer with CO2/CH4 selectivity between 40 and 50.The CO2 permeability of PEO-based membranes increases,without much change in selectivity,when the length of ethylene oxide is increased.
基金supported by the National Natural Science Foundation of China(No.314 008 55)the Technological Innovation Incubator Program from Henan University of Technology(No.201 518)the Introduced Postdoctoral Talents of Henan University of Technology(No.150 199)
文摘Cell labeling with magnetic iron oxide nanoparticles(IONPs)is increasingly a routine approach in the cellbased cancer treatment.However,cell labeling with magnetic IONPs and their leading effects on the biological properties of human lung carcinoma cells remain scarcely reported.Therefore,in the present study the magnetic c-Fe2O3nanoparticles(MNPs)were firstly synthesized and surface-modified with cationic poly-L-lysine(PLL)to construct the PLL-MNPs,which were then used to magnetically label human A549 lung cancer cells.Cell viability and proliferation were evaluated with propidium iodide/fluorescein diacetate double staining and standard 3-(4,5-dimethylthiazol-2-diphenyl-tetrazolium)bromide assay,and the cytoskeleton was immunocytochemically stained.The cell cycle of the PLL-MNPlabeled A549 lung cancer cells was analyzed using flow cytometry.Apoptotic cells were fluorescently analyzed with nuclear-specific staining after the PLL-MNP labeling.The results showed that the constructed PLL-MNPs efficiently magnetically labeled A549 lung cancer cells and that,at low concentrations,labeling did not affect cellular viability,proliferation capability,cell cycle,and apoptosis.Furthermore,the cytoskeleton in the treated cells was detected intact in comparison with the untreated counterparts.However,the results also showed that at high concentration(400 lg m L-1),the PLL-MNPs would slightly impair cell viability,proliferation,cell cycle,and apoptosis and disrupt the cytoskeleton in the treated A549 lung cancer cells.Therefore,the present results indicated that the PLL-MNPs at adequate concentrations can be efficiently used for labeling A549 lung cancer cells and could be considered as a feasible approach for magnetic targeted anti-cancer drug/gene delivery,targeted diagnosis,and therapy in lung cancer treatment.
基金Financial support from the National Science and Technology Planning Project (No. 2011BAC08B00)the National High Technology Research and Development Program of China (863 Program) (No.2012AA03A611)
文摘Membranes from block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074) and its blends with different molecular weight poly(ethylene glycol)(PEG)(200, 400, 600, 1500, 4600 and 8000) were prepared. The thermal properties and structures of Pebax1074/PEG blend membranes were characterized by DSC and SEM, and the gas permeation properties of CO_2 and N_2 were also investigated at different temperatures. For Pebax1074/PEG blend membranes with low molecular weight PEG(MW≤ 600), higher gas permeabilities than Pebax1074 were achieved. The permeability increased with the increase of PEG molecular weight. The addition of low molecular weight PEG resulted in decrease in activation energy of permeation. For Pebax1074/PEG blend membranes with high molecular weight PEG(MW≥ 1500), due to the melt of PEO phase crystals, the gas permeation properties of blend membranes were temperaturedependent, which could be divided into crystalline region, transition region and amorphous region according to two different transition temperatures. PEG molecular weight and operation temperature determined different gas permeation properties of Pebax1074/PEG blend membranes in three regions. The activation energies of permeation in crystalline region were larger than those in amorphous region.
文摘A new process for preparing poly(phenylene sulfide amide, PPSA), which is by reaction of sulfur instead of sodium sulfide as S source with dichlorobenzamide (DCBA) and alkali in polar organic solvent at the atmospheric pressure (called sulfur solution route), is reported in the present paper. The influences of polymerization time, molar ratio of precursors, catalyst and solvent upon the polymer were investigated. To seek the best parameters of polymerization, orthogonal design was employed in the experiments. The results indicate that the molar ratio of precursors is the most significant effect on both of viscosity and yield of the polymer. The suitable parameters for preparing the related polymer are presented. The polymer was characterized by IRspectrum, 1HNMRspectrum and Raman spectrum, etc.
基金supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP)the Ministry of Trade,Industry&Energy(MOTIE)of the Republic of Korea(No.20164030201070)supported by Basic Science Research Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Science,ICT and future Planning(NRF-2017R1A2B4005230)
文摘A ternary hybrid membrane architecture consisting of sulfonated fluorinated multi-block copolymer （SFMC）, sulfonated （poly ether ether ketone） （SPEEK） and I or 5 wt% graphene oxide （GO） was fabricated through a facile solution casting approach. The simple, but effective monomer sulfonation was performed for SFMC to create compact and rigid hydrophobic backbone structures, while conventional random sulfonation was carried-out for SPEEK. Hydrophilic-hydrophobic-hydrophilic structure of SFMC enhances the compatibility with SPEEK and GO and allows for an unprecedented approach to alter me- chanical strength and proton conductivity of ternary hybrid membrane, as verified from universal test machine （UTM） curves and alternating current （AC） impedance plots. The impact of GO integration on the morphology and roughness of hybrid membrane was scrutinized using field emission scanning electron microscope （FE-SEM） and atomic force microscope （AFM）. Ternary hybrid showed uniform intercalation of GO nanosheets throughout the entire surface of membrane with an increased surface roughness of 8.91 nm. The constructed ternary hybrid membrane revealed excellent water absorption, ion exchange capacity and gas barrier properties, while retaining reasonable dimensional stability. The well-optimized ternary hybrid membrane containing 5 wt% GO revealed a maximum proton conductivity of 111.9 mS/cm, which is higher by a factor of two-fold with respect to that of bare SFMC membrane. The maximum PEMFC power density of 528.07mW/cm2 was yielded by ternary hybrid membrane at a load current density of 1321.1 mA/cm2 when operating the cell at 70 ℃ under 100% relative humidity （RH）. In comparison, a maximum power density of only 182.06 mW/cm2 was exhibited by the bare SFMC membrane at a load current density of 455.56 mA/cm2 under same operating conditions.
文摘The drying of aqueous poly（ethylene oxide） （PEO） droplet on a substrate at different temperatures was studied. It was found that the contact line receded when the substrate was at a temperature above 60 ℃. Different nucleation behavior and surface profiles of PEO films were found in different droplets drying processes. The rheological properties of aqueous PEO solutions were studied to understand the mechanism of contact line recession and micro-flow in drying aqueous PEO droplets. It was found that at low temperature, the contact line was static because of great viscous stress; while at high temperature, it receded because of great Marangoni force and the decrease of viscous stress. It was indicated that Marangoni convection was inhibited by the outward capillary flow and viscous stress at low temperature, whereas it became dominant at high temperature. Two types of mechanism for surface profiles and nucleation of PEO film from drying droplets are proposed, providing a theoretical guide for polymer solution application in oil and gas foam flooding technology.
基金supported by the National Natural Science Foundation of China (U21A2075, 22179117)the Fujian Science & Technology Innovation Laboratory for Energy Devices of China (21CLAB) (21C-OP-202107)the Program of Zhejiang University and Program of State Key Laboratory of Clean Energy Utilization at Zhejiang (ZJUCEU2020005)
文摘Solid-state polymer electrolytes(SPEs)have attracted increasing attention due to good interfacial contact,light weight,and easy manufacturing.However,the practical application of SPEs such as the most widely studied poly(ethylene oxide)(PEO)in high-energy solid polymer batteries is still challenging,and the reasons are yet elusive.Here,it is found that the mismatch between PEO and 4.2 V-class cathodes is beyond the limited electrochemical window of PEO in the solid Li Ni_(1/3)Mn_(1/3)Co_(1/3)O_(2)(NMC)-PEO batteries.The initial oxidation of PEO initiates remarkable surface reconstruction of NMC grains in solid batteries that are different from the situation in liquid electrolytes.Well-aligned nanovoids are observed in NMC grains during the diffusion of surface reconstruction layers towards the bulk in solid batteries.The substantial interphasial degradation,therefore,blocks smooth Li+transport across the NMC-PEO interface and causes performance degradation.A thin yet effective Li F-containing protection layer on NMC can effectively stabilize the NMC-PEO interface with a greatly improved lifespan of NMC|PEO|Li batteries.This work deepens the understanding of degradations in high-voltage solid-state polymer batteries.
基金supported by National Natural Science Foundation of China(Grant No.22209012).
文摘The interfacial instability of the poly(ethylene oxide)(PEO)-based electrolytes impedes the long-term cycling and further application of all-solid-state lithium metal batter-ies.In this work,we have shown an effective additive 1-adaman-tanecarbonitrile,which con-tributes to the excellent per-formance of the poly(ethylene oxide)-based electrolytes.Owing to the strong interaction of the 1-Adamantanecarboni-trile to the polymer matrix and anions,the coordination of the Li^(+)-EO is weakened,and the binding effect of anions is strengthened,thereby improving the Li^(+)conductivity and the electrochemical stability.The diamond building block on the surface of the lithium anode can sup-press the growth of lithium dendrites.Importantly,the 1-Adamantanecarbonitrile also regulates the formation of LiF in the solid electrolyte interface and cathode electrolyte interface,which contributes to the interfacial stability(especially at high voltages)and protects the electrodes,enabling all-solid-state batteries to cycle at high voltages for long periods of time.Therefore,the Li/Li symmetric cell undergoes long-term lithium plating/stripping for more than 2000 h.1-Adamantanecarbonitrile-poly(ethylene oxide)-based LFP/Li and 4.3 V Ni_(0.8)Mn_(0.1)Co_(0.1)O_(2)/Li all-solid-state batteries achieved stable cycles for 1000 times,with capacity retention rates reaching 85%and 80%,respectively.
基金supported by the National Natural Science Foundation of China(51773134)the Sichuan Science and Technology Program(2019YFH0112)the Fundamental Research Funds for the Central Universities。
文摘Poly(ethylene oxide)(PEO)and its derivatives based gel polymer electrolytes(GPEs)are severely limited in advanced and safe lithium-ion batteries(LIBs)owing to the intrinsically high flammability of liquid electrolytes and PEO.Directly adding flame retardants to the GPEs can suppress their flammability and thus improve the safety of LIBs,but results in deteriorative electrochemical performance.Herein,a novel GPE with chemically bonded flame retardant(i.e.diethyl vinylphosphonate)in cross-linked polyethylene glycol diacrylate matrix,featuring both high-safety and high-performance,is designed.This as-prepared GPE storing the commercial 1 mol L^(-1) LiPF6 electrolyte resists high temperature of 200℃and cannot be ignited as well as possesses a high ionic conductivity(0.60 m S cm^(-1))and good compatibility with lithium.Notably,the LiFePO_(4)/Li battery with this GPE delivers a satisfactory capacity of 142.2 m A h g^(-1) and a superior cycling performance with a capacity retention of 96.3%and a coulombic efficiency of close to 100%for 350 cycles at 0.2 C under ambient temperature.Furthermore,the battery can achieve steady charge–discharge for 100 cycles with a coulombic efficiency of 99.5%at 1 C under 80℃and run normally even at a high temperature of 150℃or under the exposure to butane flame.Differential scanning calorimetry manifests significantly improved battery safety compared to commercial battery systems.This work provides a new pathway for developing next-generation advanced LIBs with enhanced performance and high safety.
基金This work was supported by the Natural Science Foundation of the Shanxi Province of China(No.201801D121069).
文摘In this study,the precursor 4-(4-carboxy-phenoxy)phthalonitrile(CPPN)was first bonded onto the silica gel surface modified with poly(glycidyl methacrylate)(PGMA)(PGMA/SiO2)to prepare CPPN-PGMA/SiO2,and metal phthalocyanine(MPc;M=Co,Fe,Cu,Mn)was supported on the PGMA/SiO2 surface to prepare MPc-PGMA/SiO2 by synchronous synthesis and immobilization with phthalonitrile and metal salt in the solution.The chemical composition and surface morphology were characterized by the Fourier transform infrared(FTIR)spectroscopy,UV-Vis spectroscopy,scanning electron microscopy(SEM),X-ray photoelectron spectroscopy(XPS),and thermogravimetry analysis(TGA).The catalytic performance of MPc-PGMA/SiO2 in epoxidation of styrene was also investigated with molecular oxygen acting as the oxidant.The results show that MPc-PGMA/SiO2 can efficiently and selectively catalyze molecular oxygen for oxidation of styrene to styrene oxide under mild conditions.However,the catalytic activity differs substantially depending on the central metal,and a highest catalytic activity is achieved by CoPc-PGMA/SiO2.The CoPc-PGMA/SiO2 amount and temperature can also affect the catalytic oxidation of styrene,and at normal atmospheric pressure,a maximum conversion rate of styrene(99%)and selectivity of styrene oxide(53%)are obtained using 0.1 g of CoPc-PGMA/SiO2(22.61μmol of CoPc)at 100℃ for 6 h.CoPc-PGMA/SiO2 also has excellent reusability,and the conversion rate of styrene is still over 90%after 5 cycles.
