Degradation and overstress failures occur in many electronic systems in which the operation load and environmental conditions are complex.The dependency of them called dependent competing failure process(DCFP),has bee...Degradation and overstress failures occur in many electronic systems in which the operation load and environmental conditions are complex.The dependency of them called dependent competing failure process(DCFP),has been widely studied.Electronic system may experience mutual effects of degradation and shocks,they are considered to be interdependent.Both the degradation and the shock processes will decrease the limit of system and cause cumulative effect.Finally,the competition of hard and soft failure will cause the system failure.Based on the failure mechanism accumulation theory,this paper constructs the shock-degradation acceleration and the threshold descent model,and a system reliability model established by using these two models.The mutually DCFP effect of electronic system interaction has been decomposed into physical correlation of failure,including acceleration,accumulation and competition.As a case,a reliability of electronic system in aeronautical system has been analyzed with the proposed method.The method proposed is based on failure physical evaluation,and could provide important reference for quantitative evaluation and design improvement of the newly designed system in case of data deficiency.展开更多
Due to the extreme complexity of mechanical response of soft surrounding rock(SR) around a tunnel under high geostatic stress conditions, the integration of physical and numerical modeling techniques was adopted. Base...Due to the extreme complexity of mechanical response of soft surrounding rock(SR) around a tunnel under high geostatic stress conditions, the integration of physical and numerical modeling techniques was adopted. Based on the similarity theory, new composite-similar material was developed, which showed good agreement with the similarity relation and successfully simulated physico-mechanical properties(PMP) of deep buried soft rock. And the 800 mm×800 mm×200 mm physical model(PM) was conducted, in which the endoscopic camera technique was adopted to track the entire process of failure of the model all the time. The experimental results indicate that the deformation of SR around a underground cavern possessed the characteristics of development by stages and in delay, and the initial damage of SR could induce rapid failure in the later stage, and the whole process could be divided into three stages, including the localized extension of crack(the horizontal load(HL) was in the range of 130 k N to 170 k N, the vertical load(VL) was in the range of 119 k N to 153.8 k N), rapid crack coalescence(the HL was in the range of 170 k N to 210 k N, the VL was in the range of 153.8 k N to 182.5 k N) and residual strength(the HL was greater than 210 k N, the VL was greater than 182.5 k N). Under the high stress conditions, the phenomenon of deformation localization in the SR became serious and different space positions show different deformation characteristics. In order to further explore the deformation localization and progressive failure phenomenon of soft SR around the deeply buried tunnel, applying the analysis software of FLAC3 D three-dimensional explicit finite-difference method, based on the composite strain-softening model of Mohr-Coulomb shear failure and tensile failure, the calculation method of large deformation was adopted. Then, the comparative analysis between the PM experiment and numerical simulation of the three centered arch tunnels was implemented and the relationship of deformation localization and progressive failure of SR around a tunnel under high stress conditions was discussed.展开更多
现有的基于失效物理(physics of failure,PoF)模型的可靠性预计只能计算电子产品在寿命周期内经历单一典型任务剖面的失效时间。本文提出了一种基于失效物理模型,并利用蒙特卡罗仿真定量分析电子产品在寿命周期内实际经历多任务剖面的...现有的基于失效物理(physics of failure,PoF)模型的可靠性预计只能计算电子产品在寿命周期内经历单一典型任务剖面的失效时间。本文提出了一种基于失效物理模型,并利用蒙特卡罗仿真定量分析电子产品在寿命周期内实际经历多任务剖面的可靠性水平的新方法。将该方法应用于某机载电子设备的平均失效前时间(mean time to failure,MTTF)的计算,建立失效率和可靠度的时间函数,与目前国内工程实践中常用的失效率经验模型法以及设备可靠性强化试验的结果进行了对比分析。结果表明,该方法不仅可以计算可靠性参数,而且通过分析与计算过程可发现设计薄弱环节与可靠性参数的定量关系,有效指导设计改进。展开更多
Recently, the physics-of-failure(PoF) method has been more and more popular in engineering to understand the failure mechanisms(FMs) of products.However, due to the lack of system modeling methods and problem-solving ...Recently, the physics-of-failure(PoF) method has been more and more popular in engineering to understand the failure mechanisms(FMs) of products.However, due to the lack of system modeling methods and problem-solving algorithms,the information of FMs cannot be used to evaluate system reliability.This paper presents a system reliability evaluation method with failure mechanism tree(FMT) considering physical dependency(PDEP) such as competition, trigger, acceleration, inhibition, damage accumulation, and parameter combination.And the binary decision diagram(BDD) analytical algorithm is developed to establish a system reliability model.The operation rules of ite operators for generating BDD are discussed.The flow chart of system reliability evaluation method based on FMT and BDD is proposed.The proposed method is applied in the case of an electronic controller drive unit.Results show that the method is effective to evaluate system reliability from the perspective of FM.展开更多
基金supported by the National Natural Science Foundation of China(61503014,62073009)。
文摘Degradation and overstress failures occur in many electronic systems in which the operation load and environmental conditions are complex.The dependency of them called dependent competing failure process(DCFP),has been widely studied.Electronic system may experience mutual effects of degradation and shocks,they are considered to be interdependent.Both the degradation and the shock processes will decrease the limit of system and cause cumulative effect.Finally,the competition of hard and soft failure will cause the system failure.Based on the failure mechanism accumulation theory,this paper constructs the shock-degradation acceleration and the threshold descent model,and a system reliability model established by using these two models.The mutually DCFP effect of electronic system interaction has been decomposed into physical correlation of failure,including acceleration,accumulation and competition.As a case,a reliability of electronic system in aeronautical system has been analyzed with the proposed method.The method proposed is based on failure physical evaluation,and could provide important reference for quantitative evaluation and design improvement of the newly designed system in case of data deficiency.
基金Projects(51374257,50804060)supported by the National Natural Science Foundation of ChinaProject(NCET-09-0844)supported by the New Century Excellent Talent Foundation from MOE of China
文摘Due to the extreme complexity of mechanical response of soft surrounding rock(SR) around a tunnel under high geostatic stress conditions, the integration of physical and numerical modeling techniques was adopted. Based on the similarity theory, new composite-similar material was developed, which showed good agreement with the similarity relation and successfully simulated physico-mechanical properties(PMP) of deep buried soft rock. And the 800 mm×800 mm×200 mm physical model(PM) was conducted, in which the endoscopic camera technique was adopted to track the entire process of failure of the model all the time. The experimental results indicate that the deformation of SR around a underground cavern possessed the characteristics of development by stages and in delay, and the initial damage of SR could induce rapid failure in the later stage, and the whole process could be divided into three stages, including the localized extension of crack(the horizontal load(HL) was in the range of 130 k N to 170 k N, the vertical load(VL) was in the range of 119 k N to 153.8 k N), rapid crack coalescence(the HL was in the range of 170 k N to 210 k N, the VL was in the range of 153.8 k N to 182.5 k N) and residual strength(the HL was greater than 210 k N, the VL was greater than 182.5 k N). Under the high stress conditions, the phenomenon of deformation localization in the SR became serious and different space positions show different deformation characteristics. In order to further explore the deformation localization and progressive failure phenomenon of soft SR around the deeply buried tunnel, applying the analysis software of FLAC3 D three-dimensional explicit finite-difference method, based on the composite strain-softening model of Mohr-Coulomb shear failure and tensile failure, the calculation method of large deformation was adopted. Then, the comparative analysis between the PM experiment and numerical simulation of the three centered arch tunnels was implemented and the relationship of deformation localization and progressive failure of SR around a tunnel under high stress conditions was discussed.
文摘现有的基于失效物理(physics of failure,PoF)模型的可靠性预计只能计算电子产品在寿命周期内经历单一典型任务剖面的失效时间。本文提出了一种基于失效物理模型,并利用蒙特卡罗仿真定量分析电子产品在寿命周期内实际经历多任务剖面的可靠性水平的新方法。将该方法应用于某机载电子设备的平均失效前时间(mean time to failure,MTTF)的计算,建立失效率和可靠度的时间函数,与目前国内工程实践中常用的失效率经验模型法以及设备可靠性强化试验的结果进行了对比分析。结果表明,该方法不仅可以计算可靠性参数,而且通过分析与计算过程可发现设计薄弱环节与可靠性参数的定量关系,有效指导设计改进。
基金supported by the National Natural Science Foundation of China (6150301462073009)。
文摘Recently, the physics-of-failure(PoF) method has been more and more popular in engineering to understand the failure mechanisms(FMs) of products.However, due to the lack of system modeling methods and problem-solving algorithms,the information of FMs cannot be used to evaluate system reliability.This paper presents a system reliability evaluation method with failure mechanism tree(FMT) considering physical dependency(PDEP) such as competition, trigger, acceleration, inhibition, damage accumulation, and parameter combination.And the binary decision diagram(BDD) analytical algorithm is developed to establish a system reliability model.The operation rules of ite operators for generating BDD are discussed.The flow chart of system reliability evaluation method based on FMT and BDD is proposed.The proposed method is applied in the case of an electronic controller drive unit.Results show that the method is effective to evaluate system reliability from the perspective of FM.
