This study examines the effects of friction stir welding(FSW)and post-weld heat treatment(PWHT)on the grain boundary character distribution and corrosion resistance of cross sectional(top and bottom)regions of nickel-...This study examines the effects of friction stir welding(FSW)and post-weld heat treatment(PWHT)on the grain boundary character distribution and corrosion resistance of cross sectional(top and bottom)regions of nickel-and molybdenum-free high-nitrogen austenitic stainless steel(HNASS).FSW at 400 rpm and 30 mm/min resulted in finer grains(4.18μm)and higher coincident site lattice(CSL)boundaries(32.3%)at the top of the stir zone(SZ)due to dynamic recrystallization(DRX).PWHT at 900℃for 1 h led to grain coarsening(12.91μm the bottom SZ)but enhanced CSL boundaries from 24.6%to 30.2%,improving grain boundary stability.PWHT reduced the kernel average misorientation(KAM)by 14.9%in the SZ-top layer and 20.4%in the SZ-bottom layer,accompanied by a 25%decrease in hardness in the SZ-top layer and 26.7%in the SZ-bottom layer,indicating strain recovery and reduced dislocation density.Potentiodynamic polarization tests(PDP)showed a 18%increase in pitting potential and a 76%reduction in corrosion rate after PWHT.The improvement in corrosion resistance is attributed to the increase inΣ3 twin boundaries,which enhance grain boundary stability and reduce susceptibility to localized corrosion.These findings highlight the role of PWHT in refining the microstructure and strengthening corrosion resistance,making HNASS a promising material for demanding applications.展开更多
An effective flotation approach is proposed for improving the recovery of molybdenite fines from a finely-disseminated molybdenum ore. To maximize the flotation recovery of molybdenum, process mineralogy of raw ore, c...An effective flotation approach is proposed for improving the recovery of molybdenite fines from a finely-disseminated molybdenum ore. To maximize the flotation recovery of molybdenum, process mineralogy of raw ore, contrast tests, optimization of operation conditions and particle size analysis were systematically investigated. Process mineralogy suggests that in the raw ore, 61.63% of molybdenite particles distribute in the 〈20 pm size fraction, and intergrow with muscovite and pyrite as the contained and disseminated type. Contrast tests indicate that conventional flotation responds to poor collection efficiency for particles less than 25 pm. Oil agglomerate flotation （OAF） process demonstrates an obvious superiority in improving the flotation recovery of molybdenite fines. Furthermore, the flotation results of OAF process reveal that the dosage of transformer oil plays a critical role on the average size of collected mineral particles （d（0）, agglomerates （d^0） and the molybdenum recovery. In addition, industrial tests illustrate that compared with the Mo-S bulk flotation approach, OAF process not only increases Mo recovery and grade of molybdenum concentrate by 22.75% and 17.47% respectively, but also achieves a sulfur concentrate with a superior grade of 38.92%.展开更多
The leaching results of bismuth sulfide concentrate containing molybdenum and tungsten in air-H2O2-NaOH system, pressure-O2-Na2CO3 system and pressure-O2-NaOH system were investigated. The results show that the extrac...The leaching results of bismuth sulfide concentrate containing molybdenum and tungsten in air-H2O2-NaOH system, pressure-O2-Na2CO3 system and pressure-O2-NaOH system were investigated. The results show that the extraction of molybdenum, tungsten and sulfur goes up with the increase of NaOH concentration, oxygen partial pressure and reaction time. The extraction of molybdenum and tungsten also rises up with temperature, but the leaching ratio of sulfur increases initially to a peak of 98% at 150℃ and then decreases with the increase of temperature. Under the optimal conditions, the extraction of molybdenum, tungsten and sulfur is more than 95.6%, 93.8% and 96.0%, respectively, and the main phases of residue are Bi2O3 and Fe2O3. Therefore, the method of pressure leaching in alkaline solution is provided as an effective separation of molybdenum, tungsten and sulfur from bismuth and a beneficial pretreatment for consequent process.展开更多
Ab initio calculations are used to understand the fundamental mechanism of the solid solution softening/hardening of the Mo-binary system.The results reveal that the Mo-Ti,Mo-Ta,Mo-Nb,and Mo-W interactions are primari...Ab initio calculations are used to understand the fundamental mechanism of the solid solution softening/hardening of the Mo-binary system.The results reveal that the Mo-Ti,Mo-Ta,Mo-Nb,and Mo-W interactions are primarily attractive with negative heats of formation,while the interactions of Mo-Re,and Mo-Zr would be mainly repulsive with positive heats of formation.It is also shown that the addition of Re and Zr would cause the solid solution softening of Mo by the decrease of the unstable stacking fault energy and the increase of ductility.On the contrary,the elements of W,Ta,Ti,and Nb could bring about the solid-solution hardening of Mo through the impediment of the slip of the dislocation and the decrease of ductility.Electronic structures indicate that the weaker/stronger chemical bonding due to the alloying elements should fundamentally induce the solid solution softening/hardening of Mo.The results are discussed and compared with available evidence in literatures,which could deepen the fundamental understanding of the solid solution softening/hardening of the binary metallic system.展开更多
The leaching kinetics of molybdenum from Ni-Mo ore in sulfuric acid solution with sodium peroxodisulfate was studied.The effects including leaching temperature, reaction time, particle size, stirring speed, and concen...The leaching kinetics of molybdenum from Ni-Mo ore in sulfuric acid solution with sodium peroxodisulfate was studied.The effects including leaching temperature, reaction time, particle size, stirring speed, and concentrations of sulfuric acid and sodium peroxodisulfate were investigated. The leaching process of molybdenum from Ni-Mo ore is controlled by the chemical reaction through the solid layer across the unreacted shrinking core. The apparent activation energy of the leaching of molybdenum is calculated to be 41.0 k J/mol and the leaching kinetics equation of molybdenum from Ni-Mo ore is expressed as1-(1-a)1/3=3405.7exp[-41030.0/(RT)]t.展开更多
A new technology of treating molybdenum residues by simultaneous ultrafine milling and alkali leaching was put forward to recover molybdenum from metallurgical residues. The effects of residue size, milling time, soli...A new technology of treating molybdenum residues by simultaneous ultrafine milling and alkali leaching was put forward to recover molybdenum from metallurgical residues. The effects of residue size, milling time, solid content, n (Na 2CO 3)/ n (Mo) and slurry pH value on molybdenum leaching rate were investigated. The results indicate that a simpler process, lower slurry temperature, 50% shorter treating time, 60% decrease of Na 2CO 3 content and 15% increase of molybdenum leaching rate can be obtained by the new technology compared with the traditional process. The leaching kinetic equation was determined, and calculation of active energy ( E =56.2 kJ/mol) shows that the leaching process of molybdenum residues by simultaneous ultrafine milling and alkali leaching is controlled by chemical reaction. Potential exists for the new process to form the basis for an economically viable, environmentally friendly process to recover valuable elements from residues.展开更多
The adsorption behavior of molybdenum onto D314 was studied with the static adsorption method. The adsorption process was analyzed from thermodynamic and kinetic aspects. The experimental results show that the equilib...The adsorption behavior of molybdenum onto D314 was studied with the static adsorption method. The adsorption process was analyzed from thermodynamic and kinetic aspects. The experimental results show that the equilibrium adsorption data conform satisfactorily to the Langmuir equation. In the adsorption process of D314 for molybdenum, the enthalpy change ΔH is positive when temperature is in the range of 298-338 K, which indicates that the adsorption is an endothermic process, and the elevated temperature benefits to the adsorption. Kinetic analysis shows that the adsorption rate is controlled by intraparticle diffusion and chemical diffusion at the same time. The adsorption mechanism of molybdenum onto D314 was discussed based on IR spectra.展开更多
The Shiyaogou deposit,located in Songxian,Henan Province,China,is a medium-sized Molybdenum deposit newly discovered in the East Qinling molybdenum belt.Occurring in the altered Proterozoic Xionger Group,mineralizatio...The Shiyaogou deposit,located in Songxian,Henan Province,China,is a medium-sized Molybdenum deposit newly discovered in the East Qinling molybdenum belt.Occurring in the altered Proterozoic Xionger Group,mineralization of the deposit consists of molybedenite disseminations and quartz -molybdenite veinlets and stockworks.Hydrothermal alteration is well developed and is composed of potassic alteration,silicification,sericitization,pyriti-展开更多
Transition metal molybdenum phosphides were prepared by direct reduction of an amorphous phosphate precursor in hydrogen at relatively low temperature (650 ℃). XRD (X ray diffraction analysis) measurements showed tha...Transition metal molybdenum phosphides were prepared by direct reduction of an amorphous phosphate precursor in hydrogen at relatively low temperature (650 ℃). XRD (X ray diffraction analysis) measurements showed that pure molybdenum phosphide formed after the reduction with H 2. The reactivity was determined in a continuous flow microreactor at a H 2 pressure of 3.0 MPa. A sample of prepared molybdenum phosphide catalyst diluted with γ Al 2O 3 (20% phosphate precursor) was used for simultaneous HDN (Hydrodenitrogenation), HDS (Hydrodesulfurization) and HDY(Hydrogenation of aromatics). The influences of space velocity, flow rate of hydrogen, reaction time and temperature on hydrotreating performance were studied. Pyridine, thiophene and cyclohexene were used as model compounds, their contents were respectively 5%, 5% and 20%. Cyclohexane was used as the solvent.展开更多
文摘This study examines the effects of friction stir welding(FSW)and post-weld heat treatment(PWHT)on the grain boundary character distribution and corrosion resistance of cross sectional(top and bottom)regions of nickel-and molybdenum-free high-nitrogen austenitic stainless steel(HNASS).FSW at 400 rpm and 30 mm/min resulted in finer grains(4.18μm)and higher coincident site lattice(CSL)boundaries(32.3%)at the top of the stir zone(SZ)due to dynamic recrystallization(DRX).PWHT at 900℃for 1 h led to grain coarsening(12.91μm the bottom SZ)but enhanced CSL boundaries from 24.6%to 30.2%,improving grain boundary stability.PWHT reduced the kernel average misorientation(KAM)by 14.9%in the SZ-top layer and 20.4%in the SZ-bottom layer,accompanied by a 25%decrease in hardness in the SZ-top layer and 26.7%in the SZ-bottom layer,indicating strain recovery and reduced dislocation density.Potentiodynamic polarization tests(PDP)showed a 18%increase in pitting potential and a 76%reduction in corrosion rate after PWHT.The improvement in corrosion resistance is attributed to the increase inΣ3 twin boundaries,which enhance grain boundary stability and reduce susceptibility to localized corrosion.These findings highlight the role of PWHT in refining the microstructure and strengthening corrosion resistance,making HNASS a promising material for demanding applications.
基金Project（2016zztsl03） supported by the Fundamental Research Funds for the Central Universities, China Project（51374249） supported by the National Natural Science Foundation of China+1 种基金 Project（2015BAB12B02） supported by the National Key Technology R＆D Program of China Project（2013B090800016） supported by Guangdong Provincial Science and Technology Plan, China
文摘An effective flotation approach is proposed for improving the recovery of molybdenite fines from a finely-disseminated molybdenum ore. To maximize the flotation recovery of molybdenum, process mineralogy of raw ore, contrast tests, optimization of operation conditions and particle size analysis were systematically investigated. Process mineralogy suggests that in the raw ore, 61.63% of molybdenite particles distribute in the 〈20 pm size fraction, and intergrow with muscovite and pyrite as the contained and disseminated type. Contrast tests indicate that conventional flotation responds to poor collection efficiency for particles less than 25 pm. Oil agglomerate flotation （OAF） process demonstrates an obvious superiority in improving the flotation recovery of molybdenite fines. Furthermore, the flotation results of OAF process reveal that the dosage of transformer oil plays a critical role on the average size of collected mineral particles （d（0）, agglomerates （d^0） and the molybdenum recovery. In addition, industrial tests illustrate that compared with the Mo-S bulk flotation approach, OAF process not only increases Mo recovery and grade of molybdenum concentrate by 22.75% and 17.47% respectively, but also achieves a sulfur concentrate with a superior grade of 38.92%.
文摘The leaching results of bismuth sulfide concentrate containing molybdenum and tungsten in air-H2O2-NaOH system, pressure-O2-Na2CO3 system and pressure-O2-NaOH system were investigated. The results show that the extraction of molybdenum, tungsten and sulfur goes up with the increase of NaOH concentration, oxygen partial pressure and reaction time. The extraction of molybdenum and tungsten also rises up with temperature, but the leaching ratio of sulfur increases initially to a peak of 98% at 150℃ and then decreases with the increase of temperature. Under the optimal conditions, the extraction of molybdenum, tungsten and sulfur is more than 95.6%, 93.8% and 96.0%, respectively, and the main phases of residue are Bi2O3 and Fe2O3. Therefore, the method of pressure leaching in alkaline solution is provided as an effective separation of molybdenum, tungsten and sulfur from bismuth and a beneficial pretreatment for consequent process.
基金Project(51801129)supported by the National Natural Science Foundation of ChinaProject supported by the State Key Laboratory of Powder Metallurgy,China。
文摘Ab initio calculations are used to understand the fundamental mechanism of the solid solution softening/hardening of the Mo-binary system.The results reveal that the Mo-Ti,Mo-Ta,Mo-Nb,and Mo-W interactions are primarily attractive with negative heats of formation,while the interactions of Mo-Re,and Mo-Zr would be mainly repulsive with positive heats of formation.It is also shown that the addition of Re and Zr would cause the solid solution softening of Mo by the decrease of the unstable stacking fault energy and the increase of ductility.On the contrary,the elements of W,Ta,Ti,and Nb could bring about the solid-solution hardening of Mo through the impediment of the slip of the dislocation and the decrease of ductility.Electronic structures indicate that the weaker/stronger chemical bonding due to the alloying elements should fundamentally induce the solid solution softening/hardening of Mo.The results are discussed and compared with available evidence in literatures,which could deepen the fundamental understanding of the solid solution softening/hardening of the binary metallic system.
基金Project(51364009) supported by the National Natural Science Foundation of ChinaProject(JSU071302) supported by the Construct Program of the Key Discipline in Hunan Province,ChinaProject(2015JJ2115) supported by the Natural Science Foundation of Hunan Province,China
文摘The leaching kinetics of molybdenum from Ni-Mo ore in sulfuric acid solution with sodium peroxodisulfate was studied.The effects including leaching temperature, reaction time, particle size, stirring speed, and concentrations of sulfuric acid and sodium peroxodisulfate were investigated. The leaching process of molybdenum from Ni-Mo ore is controlled by the chemical reaction through the solid layer across the unreacted shrinking core. The apparent activation energy of the leaching of molybdenum is calculated to be 41.0 k J/mol and the leaching kinetics equation of molybdenum from Ni-Mo ore is expressed as1-(1-a)1/3=3405.7exp[-41030.0/(RT)]t.
文摘A new technology of treating molybdenum residues by simultaneous ultrafine milling and alkali leaching was put forward to recover molybdenum from metallurgical residues. The effects of residue size, milling time, solid content, n (Na 2CO 3)/ n (Mo) and slurry pH value on molybdenum leaching rate were investigated. The results indicate that a simpler process, lower slurry temperature, 50% shorter treating time, 60% decrease of Na 2CO 3 content and 15% increase of molybdenum leaching rate can be obtained by the new technology compared with the traditional process. The leaching kinetic equation was determined, and calculation of active energy ( E =56.2 kJ/mol) shows that the leaching process of molybdenum residues by simultaneous ultrafine milling and alkali leaching is controlled by chemical reaction. Potential exists for the new process to form the basis for an economically viable, environmentally friendly process to recover valuable elements from residues.
基金Project(51104186)supported by the National Natural Science Foundation of China
文摘The adsorption behavior of molybdenum onto D314 was studied with the static adsorption method. The adsorption process was analyzed from thermodynamic and kinetic aspects. The experimental results show that the equilibrium adsorption data conform satisfactorily to the Langmuir equation. In the adsorption process of D314 for molybdenum, the enthalpy change ΔH is positive when temperature is in the range of 298-338 K, which indicates that the adsorption is an endothermic process, and the elevated temperature benefits to the adsorption. Kinetic analysis shows that the adsorption rate is controlled by intraparticle diffusion and chemical diffusion at the same time. The adsorption mechanism of molybdenum onto D314 was discussed based on IR spectra.
文摘The Shiyaogou deposit,located in Songxian,Henan Province,China,is a medium-sized Molybdenum deposit newly discovered in the East Qinling molybdenum belt.Occurring in the altered Proterozoic Xionger Group,mineralization of the deposit consists of molybedenite disseminations and quartz -molybdenite veinlets and stockworks.Hydrothermal alteration is well developed and is composed of potassic alteration,silicification,sericitization,pyriti-
文摘Transition metal molybdenum phosphides were prepared by direct reduction of an amorphous phosphate precursor in hydrogen at relatively low temperature (650 ℃). XRD (X ray diffraction analysis) measurements showed that pure molybdenum phosphide formed after the reduction with H 2. The reactivity was determined in a continuous flow microreactor at a H 2 pressure of 3.0 MPa. A sample of prepared molybdenum phosphide catalyst diluted with γ Al 2O 3 (20% phosphate precursor) was used for simultaneous HDN (Hydrodenitrogenation), HDS (Hydrodesulfurization) and HDY(Hydrogenation of aromatics). The influences of space velocity, flow rate of hydrogen, reaction time and temperature on hydrotreating performance were studied. Pyridine, thiophene and cyclohexene were used as model compounds, their contents were respectively 5%, 5% and 20%. Cyclohexane was used as the solvent.
