Reaxgen program for the pyrolysis mechanism of cycloalkanes was adopted to simulate the heat sink of substituted cyclohexanes. Thermal cracking of cyclohexanes was performed to examine the cracking performance, wherei...Reaxgen program for the pyrolysis mechanism of cycloalkanes was adopted to simulate the heat sink of substituted cyclohexanes. Thermal cracking of cyclohexanes was performed to examine the cracking performance, wherein the substituent effects were detailedly discussed under supercritical condition. It was found that Reaxgen program played a good part in the screening and optimization of cyclohexanes. A good agreement with the experimental data for the mono-substituted and bi-substituted cyclohexanes was demonstrated, however, some deviation for the tri-substituted cyclohexanes were observed. The experiment results indicated that the gaseous product yield increased sharply for mono- substituted cyclohexanes with short substituents containing no more than two carbons. Nevertheless, continuous increase in the alkyl chain depressed the gaseous product yield smoothly. The cyclic substituent dramatically inhibited the pyrolysis of cyclohexanes. All the substituents but cyclohexyl had no obvious effect on the yield of hydrogen and olefins （≤C4）. For bi-substituted cyclohexanes, the more close the distance between the two substituents, the higher the gaseous product yield was obtained. However, opposite result on the selectivity to hydrogen and olefins （≤C4） was generally obtained except 1,3-dimethylcyclohexane. The position of tri-substituents acted little significance on the gaseous product yield, as well as the selectivity to hydrogen and olefins （≤C4）.展开更多
An actively water-cooled limiter has been designed for the long pulse operation of an HT-7 device, by adopting an integrated structure-doped graphite and a copper alloy heat sink with a super carbon sheet serving as a...An actively water-cooled limiter has been designed for the long pulse operation of an HT-7 device, by adopting an integrated structure-doped graphite and a copper alloy heat sink with a super carbon sheet serving as a compliant layer between them. The behaviors of the integrated structure were evaluated in an electron beam facility under different heat loads and cooling conditions. The surface temperature and bulk temperature distribution were carefully measured by optical pyrometers and thermocouples under a steady state heat flux of 1 to 5 MW/m^2 and a water flow rate of 3 m^3/h, 4.5 m^3/h and 6 m^3/h, respectively. It was found that the surface temperature increased rapidly with the heat flux rising, but decreased only slightly with the water flow rate rising. The surface temperature reached approximately 1200℃ at 5 MW/m^2 of heat flux and 6 m^3/h of water flow. The primary experimental results indicate that the integrated design meets the requirements for the heat expelling capacity of the HT-7 device. A set of numerical simulations was also completed, whose outcome was in good accord with the experimental results.展开更多
A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance ...A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance of the thermal conductive adhesive. Influence disciplines of those parameters on temperatures of the solar cell and heat sink are obtained. With optimized number, height and thickness of fins, and the thickness values of base of 8, 1.4 cm, 1.5 mm, and 2 mm, the lowest temperatures of the solar cell and heat sink are 41.7 ~C and 36.3 ~C respectively. A concentrator solar cell prototype with a heat sink fabricated based on the simulation optimized structure is built. Outdoor temperatures of the prototype are tested. Temperatures of the solar cell and heat sink are stabilized with time continuing at about 37 ℃-38 ℃ and 35 ℃-36 ℃respectively, slightly lower than the simulation results because of effects of the wind and cloud. Thus the simulation model enables to predict the thermal performance of the system, and the simulation results can be a reference for designing heat sinks in the field of single concentrator solar cells.展开更多
Considering utilization of the original chromium-bronze material, two processing techniques including hydraulic expansion and high temperature vacuum welding were proposed for the optimization of heat-sink structure i...Considering utilization of the original chromium-bronze material, two processing techniques including hydraulic expansion and high temperature vacuum welding were proposed for the optimization of heat-sink structure in EAST. The heat transfer performance of heat-sink with or without cooling tube was calculated and different types of connection between tube and heat-sink were compared by conducting a special test. It is shown from numerical analysis that the diameter of heat-sink channel can be reduced from 12 mm to 10 mm. Compared with the original sample, the thermal contact resistance between tube and heat-sink for welding sample can reduce the heat transfer performance by 10%, while by 20% for the hydraulic expansion sample. However, the welding technique is more complicated and expensive than hydraulic expansion technique. Both the processing technique and the heat transfer performance of heat-sink prototype should be further considered for the optimization of heat-sink structure in EAST.展开更多
We present a micro-Pirani vacuum gauge using the low-resistivity monocrystal silicon as the heaters and heat sinks fabricated by the post complementary metal oxide semiconductor （CMOS） microelectromechanical system ...We present a micro-Pirani vacuum gauge using the low-resistivity monocrystal silicon as the heaters and heat sinks fabricated by the post complementary metal oxide semiconductor （CMOS） microelectromechanical system （MEMS） process. The metal interconnection of the device is fabricated by a 0.5 μm standard CMOS process on 8-inch silicon wafer. Then, a SiO2-Si low-temperature fusion bonding is developed to bond the CMOS wafer and the MEMS wafer, with the electrical connection realized by the tungsten through silicon via process. Wafer- level A1Ge euteetic bonding is adopted to package the Pirani gauge in a non-hermetic cavity to protect the gauge from being damaged or contaminated in the dicing and assembling process, and to make it suitable for actual applications. To increase the accuracy of the test and restrain negative influence of temperature drift, the Wheatstone bridge structure is introduced. The test results show that before capping, the gauge has an average sensitivity of 1.04 × 104 K.W-1Torr-1 in dynamic range of 0.01 20 Torr. After capping, the sensitivity of the gauge does not decrease but increases to 1.12 × 104 K.W-1 Torr-1.展开更多
聚变堆主机关键系统综合研究设施(Comprehensive Research Facility for Fusion Technology,CRAFT)超临界氦阀箱内的超临界氦循环泵为超导磁体提供大流量超临界氦,根据功能要求对超临界氦泵体的隔热区域进行了隔热设计。确定了氦循环泵...聚变堆主机关键系统综合研究设施(Comprehensive Research Facility for Fusion Technology,CRAFT)超临界氦阀箱内的超临界氦循环泵为超导磁体提供大流量超临界氦,根据功能要求对超临界氦泵体的隔热区域进行了隔热设计。确定了氦循环泵的隔热结构,计算分析了热沉位置范围,对氦循环泵的漏热量进行了核算;采用仿真软件ANSYS,数值分析了氦循环泵的隔热性能和热沉位置对泵体漏热的影响,结果显示热沉位置H为0.064 m时,可保证液氦质量流量,泵体漏热达到最小值8.71 W,满足此值小于10 W的指标要求。展开更多
Multi-element doped graphite, GBST1308 has been developed as a plasma facing material (PFM) for high heat flux components of the HT-7U device. The thermal performance of the material under steady-state (SS) high heat ...Multi-element doped graphite, GBST1308 has been developed as a plasma facing material (PFM) for high heat flux components of the HT-7U device. The thermal performance of the material under steady-state (SS) high heat flux was evaluated under actively cooling conditions, the specimens were mechanically joined to copper heat sink with supercarbon sheet as a compliant layer between the interfaces. The experiments have been performed in a facility of ACT (actively cooling test stand) with a 100 kW electron gun in order to test the suitability and the loading limit of such materials. The surface temperature and bulk temperature distribution of the specimens were investigated. The experimental results are very encouraging that when heat flux is not more than 6 MW/m2, the surface temperature of GBST1308 is less than 1000℃, which is the lowest, compared with IG-430U and even with CX-2002U (CFC); The primary results indicate that the mechanically-joined material system by such a proper design as thin tile, super compliant layer, GBST as a PFM and copper-alloy heat sink, can be used as divertor plates for HT-7U in the first phase.展开更多
Radiative heat transfer in the steady two-dimensional flow of Walters＇ B fluid with a non-uniform heat source/sink is investigated. An incompressible fluid is bounded by a stretching porous surface. The convective bo...Radiative heat transfer in the steady two-dimensional flow of Walters＇ B fluid with a non-uniform heat source/sink is investigated. An incompressible fluid is bounded by a stretching porous surface. The convective boundary condition is used for the thermal boundary layer problem. The relevant equations are first simplified under usual boundary layer assumptions and then transformed into a similar form by suitable transformations. Explicit series solutions of velocity and temperature are derived by the homotopy analysis method （HAM）. The dimensionless velocity and temperature gradients at the wall are calculated and discussed.展开更多
基金supported by the Special Program for Key Basic Research in China(Grant No.0040202204)
文摘Reaxgen program for the pyrolysis mechanism of cycloalkanes was adopted to simulate the heat sink of substituted cyclohexanes. Thermal cracking of cyclohexanes was performed to examine the cracking performance, wherein the substituent effects were detailedly discussed under supercritical condition. It was found that Reaxgen program played a good part in the screening and optimization of cyclohexanes. A good agreement with the experimental data for the mono-substituted and bi-substituted cyclohexanes was demonstrated, however, some deviation for the tri-substituted cyclohexanes were observed. The experiment results indicated that the gaseous product yield increased sharply for mono- substituted cyclohexanes with short substituents containing no more than two carbons. Nevertheless, continuous increase in the alkyl chain depressed the gaseous product yield smoothly. The cyclic substituent dramatically inhibited the pyrolysis of cyclohexanes. All the substituents but cyclohexyl had no obvious effect on the yield of hydrogen and olefins （≤C4）. For bi-substituted cyclohexanes, the more close the distance between the two substituents, the higher the gaseous product yield was obtained. However, opposite result on the selectivity to hydrogen and olefins （≤C4） was generally obtained except 1,3-dimethylcyclohexane. The position of tri-substituents acted little significance on the gaseous product yield, as well as the selectivity to hydrogen and olefins （≤C4）.
基金The project partially supported by National Natural Science Foundation of China (No. 10275069)
文摘An actively water-cooled limiter has been designed for the long pulse operation of an HT-7 device, by adopting an integrated structure-doped graphite and a copper alloy heat sink with a super carbon sheet serving as a compliant layer between them. The behaviors of the integrated structure were evaluated in an electron beam facility under different heat loads and cooling conditions. The surface temperature and bulk temperature distribution were carefully measured by optical pyrometers and thermocouples under a steady state heat flux of 1 to 5 MW/m^2 and a water flow rate of 3 m^3/h, 4.5 m^3/h and 6 m^3/h, respectively. It was found that the surface temperature increased rapidly with the heat flux rising, but decreased only slightly with the water flow rate rising. The surface temperature reached approximately 1200℃ at 5 MW/m^2 of heat flux and 6 m^3/h of water flow. The primary experimental results indicate that the integrated design meets the requirements for the heat expelling capacity of the HT-7 device. A set of numerical simulations was also completed, whose outcome was in good accord with the experimental results.
基金supported by the Doctoral Initial Fund of Beijing University of Technology,China(Grant No.X0006015201101)the National Natural Science Foundation of China(Grant Nos.60876006 and 51202007)
文摘A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance of the thermal conductive adhesive. Influence disciplines of those parameters on temperatures of the solar cell and heat sink are obtained. With optimized number, height and thickness of fins, and the thickness values of base of 8, 1.4 cm, 1.5 mm, and 2 mm, the lowest temperatures of the solar cell and heat sink are 41.7 ~C and 36.3 ~C respectively. A concentrator solar cell prototype with a heat sink fabricated based on the simulation optimized structure is built. Outdoor temperatures of the prototype are tested. Temperatures of the solar cell and heat sink are stabilized with time continuing at about 37 ℃-38 ℃ and 35 ℃-36 ℃respectively, slightly lower than the simulation results because of effects of the wind and cloud. Thus the simulation model enables to predict the thermal performance of the system, and the simulation results can be a reference for designing heat sinks in the field of single concentrator solar cells.
文摘Considering utilization of the original chromium-bronze material, two processing techniques including hydraulic expansion and high temperature vacuum welding were proposed for the optimization of heat-sink structure in EAST. The heat transfer performance of heat-sink with or without cooling tube was calculated and different types of connection between tube and heat-sink were compared by conducting a special test. It is shown from numerical analysis that the diameter of heat-sink channel can be reduced from 12 mm to 10 mm. Compared with the original sample, the thermal contact resistance between tube and heat-sink for welding sample can reduce the heat transfer performance by 10%, while by 20% for the hydraulic expansion sample. However, the welding technique is more complicated and expensive than hydraulic expansion technique. Both the processing technique and the heat transfer performance of heat-sink prototype should be further considered for the optimization of heat-sink structure in EAST.
基金Supported by the National High Technology Research and Development Program of China under Grant No 2015AA042602
文摘We present a micro-Pirani vacuum gauge using the low-resistivity monocrystal silicon as the heaters and heat sinks fabricated by the post complementary metal oxide semiconductor （CMOS） microelectromechanical system （MEMS） process. The metal interconnection of the device is fabricated by a 0.5 μm standard CMOS process on 8-inch silicon wafer. Then, a SiO2-Si low-temperature fusion bonding is developed to bond the CMOS wafer and the MEMS wafer, with the electrical connection realized by the tungsten through silicon via process. Wafer- level A1Ge euteetic bonding is adopted to package the Pirani gauge in a non-hermetic cavity to protect the gauge from being damaged or contaminated in the dicing and assembling process, and to make it suitable for actual applications. To increase the accuracy of the test and restrain negative influence of temperature drift, the Wheatstone bridge structure is introduced. The test results show that before capping, the gauge has an average sensitivity of 1.04 × 104 K.W-1Torr-1 in dynamic range of 0.01 20 Torr. After capping, the sensitivity of the gauge does not decrease but increases to 1.12 × 104 K.W-1 Torr-1.
文摘聚变堆主机关键系统综合研究设施(Comprehensive Research Facility for Fusion Technology,CRAFT)超临界氦阀箱内的超临界氦循环泵为超导磁体提供大流量超临界氦,根据功能要求对超临界氦泵体的隔热区域进行了隔热设计。确定了氦循环泵的隔热结构,计算分析了热沉位置范围,对氦循环泵的漏热量进行了核算;采用仿真软件ANSYS,数值分析了氦循环泵的隔热性能和热沉位置对泵体漏热的影响,结果显示热沉位置H为0.064 m时,可保证液氦质量流量,泵体漏热达到最小值8.71 W,满足此值小于10 W的指标要求。
基金This work was supported by National Meg-Science Engineering Project of Chinese Gevernment.
文摘Multi-element doped graphite, GBST1308 has been developed as a plasma facing material (PFM) for high heat flux components of the HT-7U device. The thermal performance of the material under steady-state (SS) high heat flux was evaluated under actively cooling conditions, the specimens were mechanically joined to copper heat sink with supercarbon sheet as a compliant layer between the interfaces. The experiments have been performed in a facility of ACT (actively cooling test stand) with a 100 kW electron gun in order to test the suitability and the loading limit of such materials. The surface temperature and bulk temperature distribution of the specimens were investigated. The experimental results are very encouraging that when heat flux is not more than 6 MW/m2, the surface temperature of GBST1308 is less than 1000℃, which is the lowest, compared with IG-430U and even with CX-2002U (CFC); The primary results indicate that the mechanically-joined material system by such a proper design as thin tile, super compliant layer, GBST as a PFM and copper-alloy heat sink, can be used as divertor plates for HT-7U in the first phase.
文摘Radiative heat transfer in the steady two-dimensional flow of Walters＇ B fluid with a non-uniform heat source/sink is investigated. An incompressible fluid is bounded by a stretching porous surface. The convective boundary condition is used for the thermal boundary layer problem. The relevant equations are first simplified under usual boundary layer assumptions and then transformed into a similar form by suitable transformations. Explicit series solutions of velocity and temperature are derived by the homotopy analysis method （HAM）. The dimensionless velocity and temperature gradients at the wall are calculated and discussed.
