稻谷籽粒内部水分扩散的快慢决定了干燥速率。本文基于Logarithmic方程,建立稻谷水分传递动力学模型,并分析热风温度(40、50、60、70℃)和风速(0.3、0.4、0.5 m/s)对稻谷(湿基水分含量23.4%)有效水分扩散系数和扩散活化能的影响。结果表...稻谷籽粒内部水分扩散的快慢决定了干燥速率。本文基于Logarithmic方程,建立稻谷水分传递动力学模型,并分析热风温度(40、50、60、70℃)和风速(0.3、0.4、0.5 m/s)对稻谷(湿基水分含量23.4%)有效水分扩散系数和扩散活化能的影响。结果表明:随着干燥温度和风速的上升,稻谷干燥速率提高,同时对应的有效水分扩散系数越大,分别为5.123×10-12~2.141×10-11m^2/s;扩散活化能从32.94 k J/mol增加至36.30 k J/mol;对比常用的5种谷物干燥模型发现,Logarithmic模型对稻谷薄层干燥的拟合度较好,R2>0.997,RMSE<2.810×10^(-3),同时该模型模拟得出的有效水分扩散系数与实际差值均低于3.8×10^(-13)m^2/s,扩散活化能均低于2.53 k J/mol,与实际值基本吻合。展开更多
A complete mathematical model for logarithmic spiral type sprag one-way clutch design and analysis is given.It assumes that the motion of all clutch components can be expressed by a model of epicyclic gearing.It takes...A complete mathematical model for logarithmic spiral type sprag one-way clutch design and analysis is given.It assumes that the motion of all clutch components can be expressed by a model of epicyclic gearing.It takes advantage of Hunt-Crossley contact impact theory to calculate the contact forces between sprags and races,and it can be used for optimization of design and comparison with other types of sprag clutches.A good deal of analysis shows that the parameters of the steady windup angle,the steady contact force,the natural frequency and natural cycle of clutch have nothing to do with the initial velocity of outer race,while the parameters of the maximum transient windup angle,the maximum transient impact force and the steady engagement time increase linearly in the mode of engaging operation of clutch.It is also shown that the strut angle has great influence on the dynamic engagement performance of clutch.The parameters of the steady windup angle,the maximum transient windup angle,the steady engaging time,the steady contact force,the maximum transient impact force and the natural cycle of clutch decrease linearly nearly with the inner strut angle,while the natural frequency of the system increases linearly with the inner strut angle.展开更多
Form milling cutter is built-for-purpose cutter which process the form surface, for example, usually process male and female circular arc face and form trench and so on. From the traditional concept, form milling cutt...Form milling cutter is built-for-purpose cutter which process the form surface, for example, usually process male and female circular arc face and form trench and so on. From the traditional concept, form milling cutter is divided into pointed tooth and relieving follow its structure. Relieving shaped cutter is more convenient than pointed tooth milling cutter, because only its rake face is needed to grind after it turn into blunting, so the current books which are used in college almost select relieving shaped cutter in order to introduce how to design the form milling cutter.The curve of the back of tooth of relieving cutter is the transversal which is formed by the rear face of tooth in the end cut plane of the milling cutter. In the past, because of the limit of the manufacturing technology, the curve of the back of tooth is often selected Archimedes’ curve, in order that the shovel-nose tool acquire the uniform motion when the cutter shovel the back, in other word, the rear face of the milling cutter rotate its axis by the new cutting lip, in the same time, it move uniformly to the axis in order to form the surface. Although this curve of the back of tooth meet the fixedness of the form of blade around grinding the cutter, the rear angle of the dot of the cutting lip don’t keep fixedness. With the development of the modern manufacturing technology, the unmanageable problem of many complex curves is already easily solved. So it is need to study the optimum profile of the curve of the back of tooth in theory, and study the design theory of the relieving shaped cutter under the condition of new manufacture, in order to ensure that the rear angle of the dot of the cutting lip keep fixedness after the relieving shaped cutter is grinded. The paper derive the curve profile of tooth of the form cutter and the modifier calculation formula of the profile of the cutter edge from the definition of the rear angle of the cutter, which establish the foundation for the precision design and manufacture of other form cutter.展开更多
The logarithmic model is often used to describe the relationships between factors.It often gives good statistical characteristics.Yet,in the process of modeling of soil and water conservation,we find out that this“g...The logarithmic model is often used to describe the relationships between factors.It often gives good statistical characteristics.Yet,in the process of modeling of soil and water conservation,we find out that this“good”model cannot guarantee good result.In this paper we make an inquiry into the intrinsic reasons.It is shown that the logarithmic model has the property of enlarging or reducing model errors,and the disadvantages of the logarithmic model are analyzed.展开更多
Considering the variation of cohesion along the depth,the upper bound solution of active earth pressure for a rough inclined wall with sloped backfill is formulated based on a log-spiral failure mechanism.For a more a...Considering the variation of cohesion along the depth,the upper bound solution of active earth pressure for a rough inclined wall with sloped backfill is formulated based on a log-spiral failure mechanism.For a more accurate prediction,the influence of intermediate principal stress is taken into consideration using the unified strength theory.Converting the search for the active pressure to an optimization problem,the most critical failure surface can be located by a natural selection-based gravitational search algorithm(GSA).The proposed method is validated compared with existing methods for noncohesive and cohesive cases and proved to be more accordance with the limit equilibrium solution.The influences of the variation of soil cohesion and intermediate principal stress on active earth pressure coefficient are then fully studied.It can be concluded that both the variations of soil cohesion and intermediate principal stress have a significant influence on the active earth pressure coefficient.展开更多
A minimum geometric power distortionless response beamforming approach against impulsive noise （including all α- stable noise） of unknown statistics is proposed. Due to that definite logarithmic moments require no ...A minimum geometric power distortionless response beamforming approach against impulsive noise （including all α- stable noise） of unknown statistics is proposed. Due to that definite logarithmic moments require no priori knowledge of impulsive noise, this new beamformer substitutes the logarithmic moments for the second-order moments and iteratively minimizes the ＂ge- ometric power＂ of the beamformer.s output snapshots, subjected to a linear constraint. Therefore, the proposed beamformer can provide significantly higher output geometric signal-to-noise-andinterference ratio. Moreover, the optimum weight vector is obtained by using a new iteration process. The simulation results prove that the new method is effective.展开更多
To overcome the shortcomings of the Lee image enhancement algorithm and its improvement based on the logarithmic image processing(LIP) model, this paper proposes what we believe to be an effective image enhancement al...To overcome the shortcomings of the Lee image enhancement algorithm and its improvement based on the logarithmic image processing(LIP) model, this paper proposes what we believe to be an effective image enhancement algorithm. This algorithm introduces fuzzy entropy, makes full use of neighborhood information, fuzzy information and human visual characteristics.To enhance an image, this paper first carries out the reasonable fuzzy-3 partition of its histogram into the dark region, intermediate region and bright region. It then extracts the statistical characteristics of the three regions and adaptively selects the parameter αaccording to the statistical characteristics of the image’s gray-scale values. It also adds a useful nonlinear transform, thus increasing the ubiquity of the algorithm. Finally, the causes for the gray-scale value overcorrection that occurs in the traditional image enhancement algorithms are analyzed and their solutions are proposed.The simulation results show that our image enhancement algorithm can effectively suppress the noise of an image, enhance its contrast and visual effect, sharpen its edge and adjust its dynamic range.展开更多
The theoretical statistical model of sea clutter is a key issue for maritime surveillance. In recent years, the statistical model of sea clutter has attracted much attention to design the detector well. Meanwhile, the...The theoretical statistical model of sea clutter is a key issue for maritime surveillance. In recent years, the statistical model of sea clutter has attracted much attention to design the detector well. Meanwhile, the circular scanning synthetic aperture radar(SAR) has been applied to wide surveillance of the sea surface.Therefore, the paper analyzes the validity of available sea clutter models for range Doppler images from different scan angles for moderate sea state in the medium grazing angle. The parameter estimation method for different distribution models employs the method of logarithmic cumulant(MoLC) based on Mellin transform uniformly. By the analysis of the fitting performance between the histogram of real data and the amplitude probability density function(PDF) of empirical distribution models and the goodness-of-fit(GoF) test for real data from different scan angles, it is indicated the generalized K(GK) distribution with generalized Gamma texture distribution can fit the sea clutter well for different scan angles in the medium grazing angle.展开更多
From the view of both objective and subjective factors,the indoor air quality(IAQ)evaluation was considered.Carbon dioxide(CO2)and formaldehyde(HCHO)were selected as the typical contaminants of indoor air,and the eval...From the view of both objective and subjective factors,the indoor air quality(IAQ)evaluation was considered.Carbon dioxide(CO2)and formaldehyde(HCHO)were selected as the typical contaminants of indoor air,and the evaluation method of logarithmic index was adopted as the evaluation means of IAQ.Then the recommended limits(RL)of typical contaminants CO2 and HCHO were given through analysis and calculation.The limits of CO2 and HCHO in Indoor Air Quality Standard of China or other existing standards probably correspond to the level of PD=25(%).The result shows that the existing standards fail to meet the requirement of the definition of "acceptable indoor air quality",that is to say,less than 20% of the people express dissatisfaction.When PD=20%,RL of CO2 and HCHO are 728×10-6 and 0.068×10-6 respectively,which are stricter than the limits in the existing standards.The method proposed in this paper is applicable to 13.1%≤PD≤86.7%.展开更多
06001 The Exposure Standard. Lin Yunzhu,MaRunshan,. Guo Zhengqiang:1(4). 1980. pp.258--265.An exposure Standard apparatus developed in NIM ispresented, The exposure range of this apparatus isfrom 0.001 to 10 lux·...06001 The Exposure Standard. Lin Yunzhu,MaRunshan,. Guo Zhengqiang:1(4). 1980. pp.258--265.An exposure Standard apparatus developed in NIM ispresented, The exposure range of this apparatus isfrom 0.001 to 10 lux·second. and the uncertainty ofthe exposure is not exceed ±0.01 logarithmic unit. Itbasically satisfies the requirements of Sensitometry andCan be used to calibrate different types ofsensitometers.展开更多
The paper is devoted to the analytic theory of differential equations.In paper shown that how to establish the analytical properties of solutions of an autonomous system of the third order special type(meromorphy of g...The paper is devoted to the analytic theory of differential equations.In paper shown that how to establish the analytical properties of solutions of an autonomous system of the third order special type(meromorphy of general solutions,instances of availability logarithmic branch points).The method for constructing the first integrals of the systems under consideration is indicated.展开更多
The accuracy of background clutter model is a key factor which determines the performance of a constant false alarm rate(CFAR) target detection method. G0 distribution is one of the optimal statistic models in the syn...The accuracy of background clutter model is a key factor which determines the performance of a constant false alarm rate(CFAR) target detection method. G0 distribution is one of the optimal statistic models in the synthetic aperture radar(SAR) image background clutter modeling and can accurately model various complex background clutters in the SAR images. But the application of the distribution is greatly limited by its disadvantages that the parameter estimation is complex and the local detection threshold is difficult to be obtained. In order to solve the above-mentioned problems, an synthetic aperture radar CFAR target detection method using the logarithmic cumulant(Mo LC) + method of moment(Mo M)-based G0 distribution clutter model is proposed. In the method, G0 distribution is used for modeling the background clutters, a new Mo LC+Mo M-based parameter estimation method coupled with a fast iterative algorithm is used for estimating the parameters of G0 distribution and an exquisite dichotomy method is used for obtaining the local detection threshold of CFAR detection, which greatly improves the computational efficiency, detection performance and environmental adaptability of CFAR detection. Experimental results show that the proposed SAR CFAR target detection method has good target detection performance in various complex background clutter environments.展开更多
文摘稻谷籽粒内部水分扩散的快慢决定了干燥速率。本文基于Logarithmic方程,建立稻谷水分传递动力学模型,并分析热风温度(40、50、60、70℃)和风速(0.3、0.4、0.5 m/s)对稻谷(湿基水分含量23.4%)有效水分扩散系数和扩散活化能的影响。结果表明:随着干燥温度和风速的上升,稻谷干燥速率提高,同时对应的有效水分扩散系数越大,分别为5.123×10-12~2.141×10-11m^2/s;扩散活化能从32.94 k J/mol增加至36.30 k J/mol;对比常用的5种谷物干燥模型发现,Logarithmic模型对稻谷薄层干燥的拟合度较好,R2>0.997,RMSE<2.810×10^(-3),同时该模型模拟得出的有效水分扩散系数与实际差值均低于3.8×10^(-13)m^2/s,扩散活化能均低于2.53 k J/mol,与实际值基本吻合。
基金Project(2011CB706800)supported by the National Basic Research Program of China
文摘A complete mathematical model for logarithmic spiral type sprag one-way clutch design and analysis is given.It assumes that the motion of all clutch components can be expressed by a model of epicyclic gearing.It takes advantage of Hunt-Crossley contact impact theory to calculate the contact forces between sprags and races,and it can be used for optimization of design and comparison with other types of sprag clutches.A good deal of analysis shows that the parameters of the steady windup angle,the steady contact force,the natural frequency and natural cycle of clutch have nothing to do with the initial velocity of outer race,while the parameters of the maximum transient windup angle,the maximum transient impact force and the steady engagement time increase linearly in the mode of engaging operation of clutch.It is also shown that the strut angle has great influence on the dynamic engagement performance of clutch.The parameters of the steady windup angle,the maximum transient windup angle,the steady engaging time,the steady contact force,the maximum transient impact force and the natural cycle of clutch decrease linearly nearly with the inner strut angle,while the natural frequency of the system increases linearly with the inner strut angle.
文摘Form milling cutter is built-for-purpose cutter which process the form surface, for example, usually process male and female circular arc face and form trench and so on. From the traditional concept, form milling cutter is divided into pointed tooth and relieving follow its structure. Relieving shaped cutter is more convenient than pointed tooth milling cutter, because only its rake face is needed to grind after it turn into blunting, so the current books which are used in college almost select relieving shaped cutter in order to introduce how to design the form milling cutter.The curve of the back of tooth of relieving cutter is the transversal which is formed by the rear face of tooth in the end cut plane of the milling cutter. In the past, because of the limit of the manufacturing technology, the curve of the back of tooth is often selected Archimedes’ curve, in order that the shovel-nose tool acquire the uniform motion when the cutter shovel the back, in other word, the rear face of the milling cutter rotate its axis by the new cutting lip, in the same time, it move uniformly to the axis in order to form the surface. Although this curve of the back of tooth meet the fixedness of the form of blade around grinding the cutter, the rear angle of the dot of the cutting lip don’t keep fixedness. With the development of the modern manufacturing technology, the unmanageable problem of many complex curves is already easily solved. So it is need to study the optimum profile of the curve of the back of tooth in theory, and study the design theory of the relieving shaped cutter under the condition of new manufacture, in order to ensure that the rear angle of the dot of the cutting lip keep fixedness after the relieving shaped cutter is grinded. The paper derive the curve profile of tooth of the form cutter and the modifier calculation formula of the profile of the cutter edge from the definition of the rear angle of the cutter, which establish the foundation for the precision design and manufacture of other form cutter.
基金Supported by the Ministry of Educational,China(2003-58)the Research Fund for thr Doctoral Programs of the Ministry of Education,China(2002-173)
文摘The logarithmic model is often used to describe the relationships between factors.It often gives good statistical characteristics.Yet,in the process of modeling of soil and water conservation,we find out that this“good”model cannot guarantee good result.In this paper we make an inquiry into the intrinsic reasons.It is shown that the logarithmic model has the property of enlarging or reducing model errors,and the disadvantages of the logarithmic model are analyzed.
基金Project(2016YFC0800200)supported by the National Key Research Plan of China。
文摘Considering the variation of cohesion along the depth,the upper bound solution of active earth pressure for a rough inclined wall with sloped backfill is formulated based on a log-spiral failure mechanism.For a more accurate prediction,the influence of intermediate principal stress is taken into consideration using the unified strength theory.Converting the search for the active pressure to an optimization problem,the most critical failure surface can be located by a natural selection-based gravitational search algorithm(GSA).The proposed method is validated compared with existing methods for noncohesive and cohesive cases and proved to be more accordance with the limit equilibrium solution.The influences of the variation of soil cohesion and intermediate principal stress on active earth pressure coefficient are then fully studied.It can be concluded that both the variations of soil cohesion and intermediate principal stress have a significant influence on the active earth pressure coefficient.
基金supported by the National High Technology Research and Development Program of China (863 Program) (2007AA701403)
文摘A minimum geometric power distortionless response beamforming approach against impulsive noise （including all α- stable noise） of unknown statistics is proposed. Due to that definite logarithmic moments require no priori knowledge of impulsive noise, this new beamformer substitutes the logarithmic moments for the second-order moments and iteratively minimizes the ＂ge- ometric power＂ of the beamformer.s output snapshots, subjected to a linear constraint. Therefore, the proposed beamformer can provide significantly higher output geometric signal-to-noise-andinterference ratio. Moreover, the optimum weight vector is obtained by using a new iteration process. The simulation results prove that the new method is effective.
基金supported by the National Natural Science Foundation of China(61472324)
文摘To overcome the shortcomings of the Lee image enhancement algorithm and its improvement based on the logarithmic image processing(LIP) model, this paper proposes what we believe to be an effective image enhancement algorithm. This algorithm introduces fuzzy entropy, makes full use of neighborhood information, fuzzy information and human visual characteristics.To enhance an image, this paper first carries out the reasonable fuzzy-3 partition of its histogram into the dark region, intermediate region and bright region. It then extracts the statistical characteristics of the three regions and adaptively selects the parameter αaccording to the statistical characteristics of the image’s gray-scale values. It also adds a useful nonlinear transform, thus increasing the ubiquity of the algorithm. Finally, the causes for the gray-scale value overcorrection that occurs in the traditional image enhancement algorithms are analyzed and their solutions are proposed.The simulation results show that our image enhancement algorithm can effectively suppress the noise of an image, enhance its contrast and visual effect, sharpen its edge and adjust its dynamic range.
基金supported by the National Natural Science Foundation of China(61621005 61671352)+2 种基金the Key Laboratory of Cognitive Radio and Information Processing,Ministry of Education(Guilin University of Electronic Technology)(CRKL160206)the Innovational Foundation of Shanghai Academy of Space Technology(SAST2016027SAST2016033)
文摘The theoretical statistical model of sea clutter is a key issue for maritime surveillance. In recent years, the statistical model of sea clutter has attracted much attention to design the detector well. Meanwhile, the circular scanning synthetic aperture radar(SAR) has been applied to wide surveillance of the sea surface.Therefore, the paper analyzes the validity of available sea clutter models for range Doppler images from different scan angles for moderate sea state in the medium grazing angle. The parameter estimation method for different distribution models employs the method of logarithmic cumulant(MoLC) based on Mellin transform uniformly. By the analysis of the fitting performance between the histogram of real data and the amplitude probability density function(PDF) of empirical distribution models and the goodness-of-fit(GoF) test for real data from different scan angles, it is indicated the generalized K(GK) distribution with generalized Gamma texture distribution can fit the sea clutter well for different scan angles in the medium grazing angle.
文摘From the view of both objective and subjective factors,the indoor air quality(IAQ)evaluation was considered.Carbon dioxide(CO2)and formaldehyde(HCHO)were selected as the typical contaminants of indoor air,and the evaluation method of logarithmic index was adopted as the evaluation means of IAQ.Then the recommended limits(RL)of typical contaminants CO2 and HCHO were given through analysis and calculation.The limits of CO2 and HCHO in Indoor Air Quality Standard of China or other existing standards probably correspond to the level of PD=25(%).The result shows that the existing standards fail to meet the requirement of the definition of "acceptable indoor air quality",that is to say,less than 20% of the people express dissatisfaction.When PD=20%,RL of CO2 and HCHO are 728×10-6 and 0.068×10-6 respectively,which are stricter than the limits in the existing standards.The method proposed in this paper is applicable to 13.1%≤PD≤86.7%.
文摘06001 The Exposure Standard. Lin Yunzhu,MaRunshan,. Guo Zhengqiang:1(4). 1980. pp.258--265.An exposure Standard apparatus developed in NIM ispresented, The exposure range of this apparatus isfrom 0.001 to 10 lux·second. and the uncertainty ofthe exposure is not exceed ±0.01 logarithmic unit. Itbasically satisfies the requirements of Sensitometry andCan be used to calibrate different types ofsensitometers.
文摘The paper is devoted to the analytic theory of differential equations.In paper shown that how to establish the analytical properties of solutions of an autonomous system of the third order special type(meromorphy of general solutions,instances of availability logarithmic branch points).The method for constructing the first integrals of the systems under consideration is indicated.
基金Project(61105020)supported by the National Natural Science Foundation of ChinaProject(13zxtk08)supported by the Key Research Platform for Research Projects of Southwest University of Science and Technology,China
文摘The accuracy of background clutter model is a key factor which determines the performance of a constant false alarm rate(CFAR) target detection method. G0 distribution is one of the optimal statistic models in the synthetic aperture radar(SAR) image background clutter modeling and can accurately model various complex background clutters in the SAR images. But the application of the distribution is greatly limited by its disadvantages that the parameter estimation is complex and the local detection threshold is difficult to be obtained. In order to solve the above-mentioned problems, an synthetic aperture radar CFAR target detection method using the logarithmic cumulant(Mo LC) + method of moment(Mo M)-based G0 distribution clutter model is proposed. In the method, G0 distribution is used for modeling the background clutters, a new Mo LC+Mo M-based parameter estimation method coupled with a fast iterative algorithm is used for estimating the parameters of G0 distribution and an exquisite dichotomy method is used for obtaining the local detection threshold of CFAR detection, which greatly improves the computational efficiency, detection performance and environmental adaptability of CFAR detection. Experimental results show that the proposed SAR CFAR target detection method has good target detection performance in various complex background clutter environments.
基金Supported by General items of Liaoning Provincial Department of Education of China(JL202016,LJKZ0732)the National Natural Science Foundation of China(11801054)。
