Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,lim...Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,limiting their practical applications.Herein,we propose a hierarchical salt-rejection(HSR)strategy to prevent salt precipitation during long-term evaporation while maintaining a rapid evaporation rate,even in high-salinity brine.The salt diffusion process is segmented into three steps—insulation,branching diffusion,and arterial transport—that significantly enhance the salt-resistance properties of the evaporator.Moreover,the HSR strategy overcomes the tradeoff between salt resistance and evaporation rate.Consequently,a high evaporation rate of 2.84 kg m^(-2) h^(-1),stable evaporation for 7 days cyclic tests in 20 wt%NaCl solution,and continuous operation for 170 h in natural seawater under 1 sun illumination were achieved.Compared with control evaporators,the HSR evaporator exhibited a>54%enhancement in total water evaporation mass during 24 h continuous evaporation in 20 wt%salt water.Furthermore,a water collection device equipped with the HSR evaporator realized a high water purification rate(1.1 kg m^(-2) h^(-1)),highlighting its potential for agricultural applications.展开更多
Based on reserve abundance,large gas fields in China can be divided into two types：type one of high abundance large gas fields,dominated by structural gas reservoirs; type two of low abundance large gas fields,domina...Based on reserve abundance,large gas fields in China can be divided into two types：type one of high abundance large gas fields,dominated by structural gas reservoirs; type two of low abundance large gas fields,dominated by stratigraphic and lithologic gas reservoirs.The formation of these two types of large gas fields is related to the highly efficient accumulation of natural gas.The accumulation of high abundance gas fields is dependent on the rapid maturation of the source kitchen and huge residual pressure difference between the gas source kitchen and reservoir,which is the strong driving force for natural gas migration to traps.Whereas the accumulation of low abundance gas fields is more complicated,involving both volume flow charge during the burial stage and diffusion flow charge during the uplift stage,which results in large area accumulation and preservation of natural gas in low porosity and low permeability reservoirs.This conclusion should assist gas exploration in different geological settings.展开更多
Perovskite/silicon tandem solar cells(PSTSCs) have exhibited huge technological potential for breaking the Shockley-Queisser limit of single-junction solar cells. The efficiency of P-I-N type PSTSCs has surpassed the ...Perovskite/silicon tandem solar cells(PSTSCs) have exhibited huge technological potential for breaking the Shockley-Queisser limit of single-junction solar cells. The efficiency of P-I-N type PSTSCs has surpassed the single-junction limit, while the performance of N-I-P type PSTSCs is far below the theoretical value. Here, we developed a composite electron transport layer for N-I-P type monolithic PSTSCs with enhanced open-circuit voltage(VOC) and power conversion efficiency(PCE). Lithium chloride(Li Cl) was added into the tin oxide(SnO_(2)) precursor solution, which simultaneously passivated the defects and increased the electron injection driving force at the electron transfer layer(ETL)/perovskite interface.Eventually, we achieved monolithic PSTSCs with an efficiency of 25.42% and V_(OC) of 1.92 V, which is the highest PCE and VOCin N-I-P type perovskite/Si tandem devices. This work on interface engineering for improving the PCE of monolithic PSTSCs may bring a new hot point about perovskite-based tandem devices.展开更多
A cyclometalated greenish-yellow emitter 2,3-diphenylimidazo[1,2-a]pyridine iridium（Ill） complex is successfully synthesized and used to fabricate phosphorescent organic light-emitting diodes. The optimized device e...A cyclometalated greenish-yellow emitter 2,3-diphenylimidazo[1,2-a]pyridine iridium（Ill） complex is successfully synthesized and used to fabricate phosphorescent organic light-emitting diodes. The optimized device exhibits a greenish-yellow emission with the peak at 523nm and a strong shoulder at 557nm, corresponding to Commission Internationale de l＇Eclairage coordinates of （0.38, 0.68）. The full width at half maximum of the device is 93 nm, which is broader than the fac-tris（2-phenylpyridine）iridium [Ir（ppy）3] based reference device of 78 nm. Meanwhile, a maximum current efficiency of 62.6 cd/A （47.51m/W） is obtained. This result is higher than a maximum current efficiency of 54.8 cd/A （431m/W） of the Ir（ppy）a based device. The results indicate that this new iridium complex may have potential applications in fabricating high color rendering index white organic light emitting diodes.展开更多
A distinctive method is proposed by simply utilizing ultrasonic technique in Ti02 electrode fabrication in order to improve the optoelectronic performance of dye-sensitized solar cells （DSSCs）. Dye molecules are at ...A distinctive method is proposed by simply utilizing ultrasonic technique in Ti02 electrode fabrication in order to improve the optoelectronic performance of dye-sensitized solar cells （DSSCs）. Dye molecules are at random and single molecular state in the ultrasonic field and the ultrasonic wave favors the diffusion and adsorption processes of dye molecules. As a result, the introduction of ultrasonic technique at room temperature leads to faster and more well-distributed dye adsorption on TiO2 as well as higher cell efficiency than regular deposition, thus the fabrication time is markedly reduced. It is found that the device based on 40 kHz ultrasonic （within 1 h） with N719 exhibits a Voc of 789 mV, Jsc of 14.94 mA]cm2 and fill factor （FF） of 69.3, yielding power conversion efficiency （PCE） of 8.16%, which is higher than device regularly dyed for 12 h （PCE = 8.06%）. In addition, the DSSC devices obtain the best efficiency （PCE = 8.68%） when the ultrasonic deposition time increases to 2.5 h. The DSSCs fabricated via ultrasonic technique presents more dye loading, larger photocurrent, less charge recombination and higher photovoltage. The charge extraction and electron impedance spectroscopy （EIS） were performed to understand the influence of ultrasonic technique on the electron recombination and performance of DSSCs.展开更多
The geochemical analysis and experimental simulation are comprehensively used to systematically study the hydrocarbon generation material,organic matter enrichment and hydrocarbon generation model of Paleogene source ...The geochemical analysis and experimental simulation are comprehensively used to systematically study the hydrocarbon generation material,organic matter enrichment and hydrocarbon generation model of Paleogene source rock in the Western Qaidam Depression,Qaidam Basin,NW China.Three main factors result in low TOC values of saline lacustrine source rock of the Qaidam Basin:relatively poor nutrient supply inhibits the algal bloom,too fast deposition rate causes the dilution of organic matter,and high organic matter conversion efficiency causes the low residual organic carbon.For this type of hydrogen-rich organic matter,due to the reduction of organic carbon during hydrocarbon generation,TOC needs to be restored based on maturity before evaluating organic matter abundance.The hydrocarbon generation of saline lacustrine source rocks of the Qaidam Basin is from two parts:soluble organic matter and insoluble organic matter.The soluble organic matter is inherited from organisms and preserved in saline lacustrine basins.It generates hydrocarbons during low-maturity stage,and the formed hydrocarbons are rich in complex compounds such as NOS,and undergo secondary cracking to form light components in the later stage;the hydrocarbon generation model of insoluble organic matter conforms to the traditional“Tissot”model,with an oil generation peak corresponding to Ro of 1.0%.展开更多
Interfacial layer has a significant impact on the achievement of highly efficient organic–inorganic hybrid perovskite solar cells(PSCs). Here, we introduced a nano-ZnMgO(magnesium doped ZnO, abbreviated as ZnMgO) as ...Interfacial layer has a significant impact on the achievement of highly efficient organic–inorganic hybrid perovskite solar cells(PSCs). Here, we introduced a nano-ZnMgO(magnesium doped ZnO, abbreviated as ZnMgO) as interfacial layer between [6, 6]-Phenyl C_(61) butyric acid methyl ester(PC_(61) BM) layer and Al electrode to replace LiF or ZnO interlayer and enhance device performance. The device efficiency has been improved from 11.43% to 15.61% and the hysteresis was decreased dramatically. Such huge enhancement of power convert efficiency(PCE) can be attributed to the low dark current density, enhancement of electron-selective contact, and low energy barrier at the PC_(61) BM/Al interface. We suggest that this simple nano-scale interlayer can provide an efficient charge transport and extraction for highly efficient PSCs.展开更多
We propose an effective method to fabricate highly efficient organic photovoltaic cells based on poly[N−9"-hepta-decanyl-2,7-carbazole-alt-5,5-(4'7'-di-2-thienyl-2'1'3'-b-enzothiadiazole):[6,6...We propose an effective method to fabricate highly efficient organic photovoltaic cells based on poly[N−9"-hepta-decanyl-2,7-carbazole-alt-5,5-(4'7'-di-2-thienyl-2'1'3'-b-enzothiadiazole):[6,6]-phenyl C71−butyric acid methyl ester(PCDTBT:PC71BM).A power conversion efficiency of as high as 5.6%and a fill factor of 53.7%are achieved from the optimized cells.The influence of surface morphology of the active layer on the performance of the cells is also investigated.展开更多
A polymeric nanopore membrane with selective ionic transport has been proposed as a potential device to convert the chemical potential energy in salinity gradients to electrical power. However, its energy conversion e...A polymeric nanopore membrane with selective ionic transport has been proposed as a potential device to convert the chemical potential energy in salinity gradients to electrical power. However, its energy conversion efficiency and power density are often limited due to the challenge in reliably controlling the size of the nanopores with the conventional chemical etching method. Here we report that without chemical etching, polyimide （PI） membranes irradiated with GeV heavy ions have negatively charged nanopores, showing nearly perfect selectivity for cations over anions, and they can generate electrical power from salinity gradients. We further demonstrate that the power generation efficiency of the PI membrane approaches the theoretical limit, and the maximum power density reaches 130m W/m2 with a modified etching method, outperforming the previous energy conversion device that was made of polymeric nanopore membranes.展开更多
In order to overcome the efficiency problem of the conventional gradient-based optimal design method,a highly-efficient viscous adjoint-based RANS equations method is applied to the aerodynamic optimal design of hover...In order to overcome the efficiency problem of the conventional gradient-based optimal design method,a highly-efficient viscous adjoint-based RANS equations method is applied to the aerodynamic optimal design of hovering rotor airfoil.The C-shaped body-fitted mesh is firstly automatically generated around the airfoil by solving the Poisson equations,and the Navier-Stokes(N-S)equations combined with Spalart-Allmaras(S-A)one-equation turbulence model are used as the governing equations to acquire the reliable flowfield variables.Then,according to multi-constrained characteristics of the optimization of high lift/drag ratio for hovering rotor airfoil,its corresponding adjoint equations,boundary conditions and gradient expressions are newly derived.On these bases,two representative rotor airfoils,NACA0012 airfoil and SC1095 airfoil,are selected as numerical examples to optimize their synthesized aerodynamic characteristics about lift/drag ratio in hover,and better aerodynamic performance of optimal airfoils are obtained compared with the baseline.Furthermore,the new designed rotor with the optimized rotor airfoil has better hover aerodynamic characteristics compared with the baseline rotor.In contrast to the baseline airfoils optimized by the finite difference method,it is demonstrated that the adjoint optimal algorithm itself is practical and highly-efficient for the aerodynamic optimization of hover rotor airfoil.展开更多
Highly efficient and stable hybrid white organic light-emitting diodes （HWOLEDs） with a mixed bipolar interlayer between fluorescent blue and phosphorescent yellow emitting layers are demonstrated. The bipolar inter...Highly efficient and stable hybrid white organic light-emitting diodes （HWOLEDs） with a mixed bipolar interlayer between fluorescent blue and phosphorescent yellow emitting layers are demonstrated. The bipolar interlayer is a mixture of p-type diphenyl （l0-phenyl-lOH-spiro [acridine-9,9＇-fluoren]-3Lyl） phosphine oxide and n-type 2＇,2- （1,3,5-benzinetriyl）-tris（1-phenyl-l-H-benzimidazole）. The electroluminance and Commission Internationale de l＇Eclairage （CIE1931） coordinates＇ characteristics can be modulated easily by adjusting the ratio of the hole- predominated material to the electron-predominated material in the interlayer. The hybrid WOLED with a p-type：n-type ratio of 1：3 shows a maximum current efficiency and power efficiency of 61.1 ed/A and 55.8 lm/W, respectively, with warm white CIE coordinates of （0.34, 0.43）. The excellent efficiency and adaptive CIE coordi- nates are attributed to the mixed interlayer with improved charge carrier balance, optimized exciton distribution, and enhanced harvesting of singlet and triplet excitons.展开更多
The in.jection of charge carriers from the electron/hole injection or transport layers in polymer light-emitting diodes potentially increases the device efficiency not by changing of charge intensity but by lattice di...The in.jection of charge carriers from the electron/hole injection or transport layers in polymer light-emitting diodes potentially increases the device efficiency not by changing of charge intensity but by lattice distortion variation and quasi-particle interactions. From the low-dimensional condensed matter physics perspective, a valid mechanism is proposed to bring a type of novel channels that, under a proper external electric field, transition- forbidden triplet excitons are transformed and partially charged by charge carriers （polarons/bipolarons）, thus are able to emit light and to enhance fluorescence greatly.展开更多
Wavelength demultiplexing waveguide couplers have important applications in integrated nanophotonic devices. Two of the most important indicators of the quality of a wavelength demultiplexing coupler are coupling effi...Wavelength demultiplexing waveguide couplers have important applications in integrated nanophotonic devices. Two of the most important indicators of the quality of a wavelength demultiplexing coupler are coupling efficiency and splitting ratio. In this study, we utilize two asymmetric high-index dielectric nanoantennas directly positioned on top of a silicon-on insulator waveguide to realize a compact wavelength demultiplexing coupler in a communication band, which is based on the interference of the waveguide modes coupled by the two nanoantennas. We add a Au substrate for further increasing the coupling efficiency. This has constructive and destructive influences on the antenna＇s in-coupling efficiency owing to the Fabry-Perot（FP） resonance in the SiO2 layer. Therefore, we can realize a wavelength demultiplexing coupler with compact size and high coupling efficiency. This coupler has widespread applications in the areas of wavelength filters,on-chip signal processing, and integrated nanophotonic circuits.展开更多
Two new AlTiN coated cemented carbide drills with Al content of 40% and 55% in weight are developed for high efficiency dry drilling of 40Cr. By studying tool durability, machined hole quality, tool wear mechanism, ch...Two new AlTiN coated cemented carbide drills with Al content of 40% and 55% in weight are developed for high efficiency dry drilling of 40Cr. By studying tool durability, machined hole quality, tool wear mechanism, chip deformation, and lubrication, the dry drilling performance of the two kinds of coated drills is analyzed. Experimental results show that the AlTiN coated drills are suitable for high efficiency dry drilling and can obtain higher quality of machined holes. The tool durability of the drill with 55% Al content is 1. 3 times of that of the drill with 40% Al content at the cutting speed of 90 m/min. The wear mechanism of two AlTiN coatings are studied in experiments. During dry drilling process, oxidative wear appears in both two kinds of drills. The oxide film is formed on the top of the coated drill containing Al content of 55%. And the oxide film helps to increase its high temperature resistance and decrease the coating flaking, thus the drill is failed because of coating subsidence. The drill with less Al content is failed due to peeling and breakage. The lubricated condition in dry drilling is improved by the high Al content coating. It helps to reduce the cutting deformation and benefits to improve the quality of machined holes. The AlTiN coating with higher Al content shows longer tool life and higher quality of machined holes in high efficiency dry drilling. Its tool life increases by 30% compared with that of the coating with less Al content.展开更多
Green manufacturing （GM） and high efficiency machining technology are inevitable trends in the field of advanced manufacturing of the 21st century. To ensure green and high-efficiency machining, a new high efficienc...Green manufacturing （GM） and high efficiency machining technology are inevitable trends in the field of advanced manufacturing of the 21st century. To ensure green and high-efficiency machining, a new high efficiency cooling technology-cryogenic pneumatic mist jet impinging cooling （CPMJI） technology is presented. For obtaining the best cooling effect, a little quantity of coolant is carried by high speed cryogenic air （-20 C ） and reaches the machining zone in the form of mist jet to enhance heat transfer. Experimental results indicate that under the conditions of 40 m/s in the jet impinging speed and 10 mm in the jet impinging distance, the critical heat flux（CHF） nearly reaches 6× 10^7 W/m^2, more than six times of the CHF of the grinding burn with a value of （8～10）×10^6 W/m^2.展开更多
The lead-free perovskite solar cells(PSCs) have drawn a great deal of research interest due to the Pb toxicity of the lead halide perovskite.CHNHSnIis a viable alternative to CHNHPbX,because it has a narrower band gap...The lead-free perovskite solar cells(PSCs) have drawn a great deal of research interest due to the Pb toxicity of the lead halide perovskite.CHNHSnIis a viable alternative to CHNHPbX,because it has a narrower band gap of 1.3 eV and a wider visible absorption spectrum than the lead halide perovskite.The progress of fabricating tin iodide PSCs with good stability has stimulated the studies of these CHNHSnIbased cells greatly.In the paper,we study the influences of various parameters on the solar cell performance through theoretical analysis and device simulation.It is found in the simulation that the solar cell performance can be improved to some extent by adjusting the doping concentration of the perovskite absorption layer and the electron affinity of the buffer and HTM,while the reduction of the defect density of the perovskite absorption layer significantly improves the cell performance.By further optimizing the parameters of the doping concentration(1.3 × 10cm~3) and the defect density(1 × 10cm~3) of perovskite absorption layer,and the electron affinity of buffer(4.0 eV) and HTM(2.6 eV),we finally obtain some encouraging results of the Jof 31.59 mA/cm~2,Vof 0.92 V,FF of 79.99%,and PCE of 23.36%.The results show that the lead-free CHNHSnIPSC is a potential environmentally friendly solar cell with high efficiency.Improving the Snstability and reducing the defect density of CHNHSnIare key issues for the future research,which can be solved by improving the fabrication and encapsulation process of the cell.展开更多
High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes （HWOLEDs） with the configuration of indium tin oxide （ITO）/ N, N, N, N-tetrakis（4-methoxyphenyl）-benzidine （MeO-TPD）：...High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes （HWOLEDs） with the configuration of indium tin oxide （ITO）/ N, N, N, N-tetrakis（4-methoxyphenyl）-benzidine （MeO-TPD）： tetrafluoro-tetracyanoqino dimethane （F4-TCNQ）/N,N-di（naphthalene-1-yl）-N,N-diphenyl-benzidine （NPB）/ 4,4-N,N-dicarbazolebiphenyl （CBP）： iridium （III） diazine complexes （MPPZ） 2 Ir（acac）/NPB/2-methyl-9,10-di（2-naphthyl）anthracene （MADN）： p-bis（p-N,N-di-phenyl-aminostyryl）benzene （DSA-ph）/bis（10-hydroxybenzo[h] quino-linato）beryllium complex （Bebq2）/LiF/Al have been fabricated and characterized. The optimal brightness of the device is 69932 cd/m2 at a voltage of 13 V, and the Commission Internationale de l’Eclairage （CIE） chromaticity coordinates are almost constant during a large voltage change of 6–12 V. Furthermore, a current efficiency of 15.3 cd/A at an illumination-relevant brightness of 1000 cd/m2 is obtained, which rolls off slightly to 13.0 cd/A at an ultra high brightness of 50000 cd/m2. We attribute this great performance to wisely selecting an appropriate spacer together with effectively utilizing the combinations of exciton-harvested orange-phosphorescence/blue-fluorescence in the device. Undoubtedly, this is one of the most exciting results in two-wavelength HWOLEDs up to now.展开更多
To master theoretical calculation for dust removal efficiency of high pressure atomization in an underground coal mine, the corresponding atomization characteristics and dust removal efficiency were both comprehensive...To master theoretical calculation for dust removal efficiency of high pressure atomization in an underground coal mine, the corresponding atomization characteristics and dust removal efficiency were both comprehensively studied in theory by virtue of related theories of hydromechanics and aerosol.According to actual measurements of flow coefficients and atomization angles of X-type swirl nozzle,computational formula was derived for atomized particle sizes of such a nozzle in conjunction with relevant empirical equation. Moreover, a mathematical model for applying high pressure atomization to dust removal in underground coal mine was also established to deduce theoretical computation formula of fractional efficiency. Then, Matlab was adopted to portray the relation curve between fractional efficiency and influence factors. In addition, a theoretical formula was also set up for removal efficiency of respirable dust and total coal dust based on dust size and frequency distribution equations. In the end,impacts of dust characteristic parameters on various dust removal efficiencies were analyzed.展开更多
Sodium-ion capacitors(SICs)have attracted appreciable attention in virtue of the higher energy and power densities compared with their rivals,supercapacitors and sodium-ion batteries.Due to the lack of sodium resource...Sodium-ion capacitors(SICs)have attracted appreciable attention in virtue of the higher energy and power densities compared with their rivals,supercapacitors and sodium-ion batteries.Due to the lack of sodium resources in cathode,presodiation is critical for SICs to further augment performances.However,current presodiation strategy utilizes metallic sodium as the presodiation material.In this strategy,assembling/disassembling of half-cells is required,which is dangerous and in creases the time and cost of SIC leading to the restriction of their industrialization and commercialization.Herein we present a safe,low-cost and high-efficiency presodiation strategy by first employing Na_(2)C_(2)O_(4) as the sacrificial salt applied in SICs.Na_(2)C_(2)O_(4) is environmentally friendly and possesses considerably low expenditure.No additional residues remain after sodium extraction ascribed to its"zero dead mass"property.When paired with commercial activated carb on as the cathode and commercial hard carbon as the ano de,the constructed pouch-type SICs exhibit high energy and power densities of 91.7 Wh/kg and 13.1 kW/kg,respectively.This work shows a prospect of realizing the safe and low-cost manufacturing for high-performance SICs commercially.展开更多
In this paper, we present a high-efficiency S-band gallium nitride （GaN） power amplifier （PA）. This amplifier is fabri- cated based on a self-developed GaN high-electron-mobility transistor （HEMT） with 10 mm gat...In this paper, we present a high-efficiency S-band gallium nitride （GaN） power amplifier （PA）. This amplifier is fabri- cated based on a self-developed GaN high-electron-mobility transistor （HEMT） with 10 mm gate width on SiC substrate. Harmonic manipulation circuits are presented in the amplifier. The matching networks consist of microstrip lines and discrete components. Open-circuited stub lines in both input and output are used to tune the 2rid harmonic wave and match the GaN HEMT to the highest efficiency condition. The developed amplifier delivers an output power of 48.5 dBm （70 W） with a power-added efficiency （PAE） of 72.2% at 2 GHz in pulse condition. When operating at 1.8-2.2 GHz （20% relative bandwidth）, the amplifier provides an output power higher than 48 dBm （,-~ 65 W）, with a PAE over 70% and a power gain above 15 dB. When operating in continuous-wave （CW） operating conditions, the amplifier gives an output power over 46 dBm （40 W） with PAE beyond 60% over the whole operation frequency range.展开更多
基金support provided by the Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone Shenzhen Park Project(HZQB-KCZYB-2020030)the Research Grants Council of Hong Kong(Project No:AoE/M-402/20.)+1 种基金the Open Project of Yunnan Precious Metals Laboratory Co.,Ltd(YPML-2023050248)the Hong Kong Innovation and Technology Commission via the Hong Kong Branch of National Precious Metals Material Engineering Research Center.
文摘Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,limiting their practical applications.Herein,we propose a hierarchical salt-rejection(HSR)strategy to prevent salt precipitation during long-term evaporation while maintaining a rapid evaporation rate,even in high-salinity brine.The salt diffusion process is segmented into three steps—insulation,branching diffusion,and arterial transport—that significantly enhance the salt-resistance properties of the evaporator.Moreover,the HSR strategy overcomes the tradeoff between salt resistance and evaporation rate.Consequently,a high evaporation rate of 2.84 kg m^(-2) h^(-1),stable evaporation for 7 days cyclic tests in 20 wt%NaCl solution,and continuous operation for 170 h in natural seawater under 1 sun illumination were achieved.Compared with control evaporators,the HSR evaporator exhibited a>54%enhancement in total water evaporation mass during 24 h continuous evaporation in 20 wt%salt water.Furthermore,a water collection device equipped with the HSR evaporator realized a high water purification rate(1.1 kg m^(-2) h^(-1)),highlighting its potential for agricultural applications.
基金sponsored by the National Key Basic Research Program of China(2007CB2095)
文摘Based on reserve abundance,large gas fields in China can be divided into two types：type one of high abundance large gas fields,dominated by structural gas reservoirs; type two of low abundance large gas fields,dominated by stratigraphic and lithologic gas reservoirs.The formation of these two types of large gas fields is related to the highly efficient accumulation of natural gas.The accumulation of high abundance gas fields is dependent on the rapid maturation of the source kitchen and huge residual pressure difference between the gas source kitchen and reservoir,which is the strong driving force for natural gas migration to traps.Whereas the accumulation of low abundance gas fields is more complicated,involving both volume flow charge during the burial stage and diffusion flow charge during the uplift stage,which results in large area accumulation and preservation of natural gas in low porosity and low permeability reservoirs.This conclusion should assist gas exploration in different geological settings.
基金supported by the National Key Research and Development Program of China (Grant No.2018YFB1500103)the National Natural Science Foundation of China (Grant No.61674084)+4 种基金the Overseas Expertise Introduction Project for Discipline Innovation of Higher Education of China (Grant No.B16027)the Tianjin Science and Technology Project (Grant No.18ZXJMTG00220)the Fundamental Research Funds for the Central Universities of Nankai University (Grant Nos.63191736,ZB19500204)the Natural Science Foundation of Tianjin (Grant No.20JCQNJC02070)the China Postdoctoral Science Foundation (Grant No.2020T130317)。
文摘Perovskite/silicon tandem solar cells(PSTSCs) have exhibited huge technological potential for breaking the Shockley-Queisser limit of single-junction solar cells. The efficiency of P-I-N type PSTSCs has surpassed the single-junction limit, while the performance of N-I-P type PSTSCs is far below the theoretical value. Here, we developed a composite electron transport layer for N-I-P type monolithic PSTSCs with enhanced open-circuit voltage(VOC) and power conversion efficiency(PCE). Lithium chloride(Li Cl) was added into the tin oxide(SnO_(2)) precursor solution, which simultaneously passivated the defects and increased the electron injection driving force at the electron transfer layer(ETL)/perovskite interface.Eventually, we achieved monolithic PSTSCs with an efficiency of 25.42% and V_(OC) of 1.92 V, which is the highest PCE and VOCin N-I-P type perovskite/Si tandem devices. This work on interface engineering for improving the PCE of monolithic PSTSCs may bring a new hot point about perovskite-based tandem devices.
文摘A cyclometalated greenish-yellow emitter 2,3-diphenylimidazo[1,2-a]pyridine iridium（Ill） complex is successfully synthesized and used to fabricate phosphorescent organic light-emitting diodes. The optimized device exhibits a greenish-yellow emission with the peak at 523nm and a strong shoulder at 557nm, corresponding to Commission Internationale de l＇Eclairage coordinates of （0.38, 0.68）. The full width at half maximum of the device is 93 nm, which is broader than the fac-tris（2-phenylpyridine）iridium [Ir（ppy）3] based reference device of 78 nm. Meanwhile, a maximum current efficiency of 62.6 cd/A （47.51m/W） is obtained. This result is higher than a maximum current efficiency of 54.8 cd/A （431m/W） of the Ir（ppy）a based device. The results indicate that this new iridium complex may have potential applications in fabricating high color rendering index white organic light emitting diodes.
基金supported by the Science Fund for Creative Research Groups(21421004)the National Basic Research 973 Program(2013CB733700)NSFC/China(21172073,21372082,21572062 and 91233207)
文摘A distinctive method is proposed by simply utilizing ultrasonic technique in Ti02 electrode fabrication in order to improve the optoelectronic performance of dye-sensitized solar cells （DSSCs）. Dye molecules are at random and single molecular state in the ultrasonic field and the ultrasonic wave favors the diffusion and adsorption processes of dye molecules. As a result, the introduction of ultrasonic technique at room temperature leads to faster and more well-distributed dye adsorption on TiO2 as well as higher cell efficiency than regular deposition, thus the fabrication time is markedly reduced. It is found that the device based on 40 kHz ultrasonic （within 1 h） with N719 exhibits a Voc of 789 mV, Jsc of 14.94 mA]cm2 and fill factor （FF） of 69.3, yielding power conversion efficiency （PCE） of 8.16%, which is higher than device regularly dyed for 12 h （PCE = 8.06%）. In addition, the DSSC devices obtain the best efficiency （PCE = 8.68%） when the ultrasonic deposition time increases to 2.5 h. The DSSCs fabricated via ultrasonic technique presents more dye loading, larger photocurrent, less charge recombination and higher photovoltage. The charge extraction and electron impedance spectroscopy （EIS） were performed to understand the influence of ultrasonic technique on the electron recombination and performance of DSSCs.
基金Supported by the PetroChina Science and Technology Project(2021DJ1808).
文摘The geochemical analysis and experimental simulation are comprehensively used to systematically study the hydrocarbon generation material,organic matter enrichment and hydrocarbon generation model of Paleogene source rock in the Western Qaidam Depression,Qaidam Basin,NW China.Three main factors result in low TOC values of saline lacustrine source rock of the Qaidam Basin:relatively poor nutrient supply inhibits the algal bloom,too fast deposition rate causes the dilution of organic matter,and high organic matter conversion efficiency causes the low residual organic carbon.For this type of hydrogen-rich organic matter,due to the reduction of organic carbon during hydrocarbon generation,TOC needs to be restored based on maturity before evaluating organic matter abundance.The hydrocarbon generation of saline lacustrine source rocks of the Qaidam Basin is from two parts:soluble organic matter and insoluble organic matter.The soluble organic matter is inherited from organisms and preserved in saline lacustrine basins.It generates hydrocarbons during low-maturity stage,and the formed hydrocarbons are rich in complex compounds such as NOS,and undergo secondary cracking to form light components in the later stage;the hydrocarbon generation model of insoluble organic matter conforms to the traditional“Tissot”model,with an oil generation peak corresponding to Ro of 1.0%.
基金financially supported by the National Basic Research Program of China, Fundamental Studies of Perovskite Solar Cells (Grant 2015CB932200)the Natural Science Foundation of China (Grants 51602149 and 61705102)+4 种基金Natural Science Foundation of Jiangsu Province, China(Grants BK20161011 and BK20161010)Young 1000 Talents Global Recruitment Program of ChinaJiangsu Specially-Appointed Professor program"Six talent peaks" Project in Jiangsu Province, ChinaStartup from Nanjing Tech University
文摘Interfacial layer has a significant impact on the achievement of highly efficient organic–inorganic hybrid perovskite solar cells(PSCs). Here, we introduced a nano-ZnMgO(magnesium doped ZnO, abbreviated as ZnMgO) as interfacial layer between [6, 6]-Phenyl C_(61) butyric acid methyl ester(PC_(61) BM) layer and Al electrode to replace LiF or ZnO interlayer and enhance device performance. The device efficiency has been improved from 11.43% to 15.61% and the hysteresis was decreased dramatically. Such huge enhancement of power convert efficiency(PCE) can be attributed to the low dark current density, enhancement of electron-selective contact, and low energy barrier at the PC_(61) BM/Al interface. We suggest that this simple nano-scale interlayer can provide an efficient charge transport and extraction for highly efficient PSCs.
基金Supported by the Natural Science Foundation of Hebei Province under Grant No F20010000306.
文摘We propose an effective method to fabricate highly efficient organic photovoltaic cells based on poly[N−9"-hepta-decanyl-2,7-carbazole-alt-5,5-(4'7'-di-2-thienyl-2'1'3'-b-enzothiadiazole):[6,6]-phenyl C71−butyric acid methyl ester(PCDTBT:PC71BM).A power conversion efficiency of as high as 5.6%and a fill factor of 53.7%are achieved from the optimized cells.The influence of surface morphology of the active layer on the performance of the cells is also investigated.
基金Supported by the National Natural Science Foundation of China under Grant No 11335003
文摘A polymeric nanopore membrane with selective ionic transport has been proposed as a potential device to convert the chemical potential energy in salinity gradients to electrical power. However, its energy conversion efficiency and power density are often limited due to the challenge in reliably controlling the size of the nanopores with the conventional chemical etching method. Here we report that without chemical etching, polyimide （PI） membranes irradiated with GeV heavy ions have negatively charged nanopores, showing nearly perfect selectivity for cations over anions, and they can generate electrical power from salinity gradients. We further demonstrate that the power generation efficiency of the PI membrane approaches the theoretical limit, and the maximum power density reaches 130m W/m2 with a modified etching method, outperforming the previous energy conversion device that was made of polymeric nanopore membranes.
文摘In order to overcome the efficiency problem of the conventional gradient-based optimal design method,a highly-efficient viscous adjoint-based RANS equations method is applied to the aerodynamic optimal design of hovering rotor airfoil.The C-shaped body-fitted mesh is firstly automatically generated around the airfoil by solving the Poisson equations,and the Navier-Stokes(N-S)equations combined with Spalart-Allmaras(S-A)one-equation turbulence model are used as the governing equations to acquire the reliable flowfield variables.Then,according to multi-constrained characteristics of the optimization of high lift/drag ratio for hovering rotor airfoil,its corresponding adjoint equations,boundary conditions and gradient expressions are newly derived.On these bases,two representative rotor airfoils,NACA0012 airfoil and SC1095 airfoil,are selected as numerical examples to optimize their synthesized aerodynamic characteristics about lift/drag ratio in hover,and better aerodynamic performance of optimal airfoils are obtained compared with the baseline.Furthermore,the new designed rotor with the optimized rotor airfoil has better hover aerodynamic characteristics compared with the baseline rotor.In contrast to the baseline airfoils optimized by the finite difference method,it is demonstrated that the adjoint optimal algorithm itself is practical and highly-efficient for the aerodynamic optimization of hover rotor airfoil.
基金Supported by the National Natural Science Foundation of China under Grant No 91441201
文摘Highly efficient and stable hybrid white organic light-emitting diodes （HWOLEDs） with a mixed bipolar interlayer between fluorescent blue and phosphorescent yellow emitting layers are demonstrated. The bipolar interlayer is a mixture of p-type diphenyl （l0-phenyl-lOH-spiro [acridine-9,9＇-fluoren]-3Lyl） phosphine oxide and n-type 2＇,2- （1,3,5-benzinetriyl）-tris（1-phenyl-l-H-benzimidazole）. The electroluminance and Commission Internationale de l＇Eclairage （CIE1931） coordinates＇ characteristics can be modulated easily by adjusting the ratio of the hole- predominated material to the electron-predominated material in the interlayer. The hybrid WOLED with a p-type：n-type ratio of 1：3 shows a maximum current efficiency and power efficiency of 61.1 ed/A and 55.8 lm/W, respectively, with warm white CIE coordinates of （0.34, 0.43）. The excellent efficiency and adaptive CIE coordi- nates are attributed to the mixed interlayer with improved charge carrier balance, optimized exciton distribution, and enhanced harvesting of singlet and triplet excitons.
文摘The in.jection of charge carriers from the electron/hole injection or transport layers in polymer light-emitting diodes potentially increases the device efficiency not by changing of charge intensity but by lattice distortion variation and quasi-particle interactions. From the low-dimensional condensed matter physics perspective, a valid mechanism is proposed to bring a type of novel channels that, under a proper external electric field, transition- forbidden triplet excitons are transformed and partially charged by charge carriers （polarons/bipolarons）, thus are able to emit light and to enhance fluorescence greatly.
基金Project supported by the National Key Research and Development Program of China(Grant Nos.2017YFA0205700 and 2015CB932403)the National Natural Science Foundation of China(Grant Nos.11174062,51472057,and 21790364)
文摘Wavelength demultiplexing waveguide couplers have important applications in integrated nanophotonic devices. Two of the most important indicators of the quality of a wavelength demultiplexing coupler are coupling efficiency and splitting ratio. In this study, we utilize two asymmetric high-index dielectric nanoantennas directly positioned on top of a silicon-on insulator waveguide to realize a compact wavelength demultiplexing coupler in a communication band, which is based on the interference of the waveguide modes coupled by the two nanoantennas. We add a Au substrate for further increasing the coupling efficiency. This has constructive and destructive influences on the antenna＇s in-coupling efficiency owing to the Fabry-Perot（FP） resonance in the SiO2 layer. Therefore, we can realize a wavelength demultiplexing coupler with compact size and high coupling efficiency. This coupler has widespread applications in the areas of wavelength filters,on-chip signal processing, and integrated nanophotonic circuits.
文摘Two new AlTiN coated cemented carbide drills with Al content of 40% and 55% in weight are developed for high efficiency dry drilling of 40Cr. By studying tool durability, machined hole quality, tool wear mechanism, chip deformation, and lubrication, the dry drilling performance of the two kinds of coated drills is analyzed. Experimental results show that the AlTiN coated drills are suitable for high efficiency dry drilling and can obtain higher quality of machined holes. The tool durability of the drill with 55% Al content is 1. 3 times of that of the drill with 40% Al content at the cutting speed of 90 m/min. The wear mechanism of two AlTiN coatings are studied in experiments. During dry drilling process, oxidative wear appears in both two kinds of drills. The oxide film is formed on the top of the coated drill containing Al content of 55%. And the oxide film helps to increase its high temperature resistance and decrease the coating flaking, thus the drill is failed because of coating subsidence. The drill with less Al content is failed due to peeling and breakage. The lubricated condition in dry drilling is improved by the high Al content coating. It helps to reduce the cutting deformation and benefits to improve the quality of machined holes. The AlTiN coating with higher Al content shows longer tool life and higher quality of machined holes in high efficiency dry drilling. Its tool life increases by 30% compared with that of the coating with less Al content.
文摘Green manufacturing （GM） and high efficiency machining technology are inevitable trends in the field of advanced manufacturing of the 21st century. To ensure green and high-efficiency machining, a new high efficiency cooling technology-cryogenic pneumatic mist jet impinging cooling （CPMJI） technology is presented. For obtaining the best cooling effect, a little quantity of coolant is carried by high speed cryogenic air （-20 C ） and reaches the machining zone in the form of mist jet to enhance heat transfer. Experimental results indicate that under the conditions of 40 m/s in the jet impinging speed and 10 mm in the jet impinging distance, the critical heat flux（CHF） nearly reaches 6× 10^7 W/m^2, more than six times of the CHF of the grinding burn with a value of （8～10）×10^6 W/m^2.
基金supported by the Graduate Student Education Teaching Reform Project,China(Grant No.JG201512)the Young Teachers Research Project of Yanshan University,China(Grant No.13LGB028)
文摘The lead-free perovskite solar cells(PSCs) have drawn a great deal of research interest due to the Pb toxicity of the lead halide perovskite.CHNHSnIis a viable alternative to CHNHPbX,because it has a narrower band gap of 1.3 eV and a wider visible absorption spectrum than the lead halide perovskite.The progress of fabricating tin iodide PSCs with good stability has stimulated the studies of these CHNHSnIbased cells greatly.In the paper,we study the influences of various parameters on the solar cell performance through theoretical analysis and device simulation.It is found in the simulation that the solar cell performance can be improved to some extent by adjusting the doping concentration of the perovskite absorption layer and the electron affinity of the buffer and HTM,while the reduction of the defect density of the perovskite absorption layer significantly improves the cell performance.By further optimizing the parameters of the doping concentration(1.3 × 10cm~3) and the defect density(1 × 10cm~3) of perovskite absorption layer,and the electron affinity of buffer(4.0 eV) and HTM(2.6 eV),we finally obtain some encouraging results of the Jof 31.59 mA/cm~2,Vof 0.92 V,FF of 79.99%,and PCE of 23.36%.The results show that the lead-free CHNHSnIPSC is a potential environmentally friendly solar cell with high efficiency.Improving the Snstability and reducing the defect density of CHNHSnIare key issues for the future research,which can be solved by improving the fabrication and encapsulation process of the cell.
基金the National Basic Research Program of China(Grant No.2009CB623604)the National Natural Science Foundation of China(Grant Nos.61204087,51173049,U0634003,61036007,and 60937001)+1 种基金the Fundamental Research Funds for the Central Universities,China(Grant Nos.2011ZB0002 and 2011ZM0009)China Postdoctoral Science Foundation
文摘High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes （HWOLEDs） with the configuration of indium tin oxide （ITO）/ N, N, N, N-tetrakis（4-methoxyphenyl）-benzidine （MeO-TPD）： tetrafluoro-tetracyanoqino dimethane （F4-TCNQ）/N,N-di（naphthalene-1-yl）-N,N-diphenyl-benzidine （NPB）/ 4,4-N,N-dicarbazolebiphenyl （CBP）： iridium （III） diazine complexes （MPPZ） 2 Ir（acac）/NPB/2-methyl-9,10-di（2-naphthyl）anthracene （MADN）： p-bis（p-N,N-di-phenyl-aminostyryl）benzene （DSA-ph）/bis（10-hydroxybenzo[h] quino-linato）beryllium complex （Bebq2）/LiF/Al have been fabricated and characterized. The optimal brightness of the device is 69932 cd/m2 at a voltage of 13 V, and the Commission Internationale de l’Eclairage （CIE） chromaticity coordinates are almost constant during a large voltage change of 6–12 V. Furthermore, a current efficiency of 15.3 cd/A at an illumination-relevant brightness of 1000 cd/m2 is obtained, which rolls off slightly to 13.0 cd/A at an ultra high brightness of 50000 cd/m2. We attribute this great performance to wisely selecting an appropriate spacer together with effectively utilizing the combinations of exciton-harvested orange-phosphorescence/blue-fluorescence in the device. Undoubtedly, this is one of the most exciting results in two-wavelength HWOLEDs up to now.
基金Financial provided by the National Natural Science Foundation of China (Nos. 51574123 and U1361118)the China Postdoctoral Science Foundation (No. 2015M 582118)
文摘To master theoretical calculation for dust removal efficiency of high pressure atomization in an underground coal mine, the corresponding atomization characteristics and dust removal efficiency were both comprehensively studied in theory by virtue of related theories of hydromechanics and aerosol.According to actual measurements of flow coefficients and atomization angles of X-type swirl nozzle,computational formula was derived for atomized particle sizes of such a nozzle in conjunction with relevant empirical equation. Moreover, a mathematical model for applying high pressure atomization to dust removal in underground coal mine was also established to deduce theoretical computation formula of fractional efficiency. Then, Matlab was adopted to portray the relation curve between fractional efficiency and influence factors. In addition, a theoretical formula was also set up for removal efficiency of respirable dust and total coal dust based on dust size and frequency distribution equations. In the end,impacts of dust characteristic parameters on various dust removal efficiencies were analyzed.
基金supported by the National Science Foundation of China(No.51907193,51822706 and 51777200)the Beijing Natural Science foundation(JQ19012)+2 种基金the Key Research Program of Frontier Sciences,CAS(No.ZDBS-LY-JSC047)the Youth Innovation Promotion Association,CAS(No.2020145)the Dalian National Laboratory for Clean Energy Cooperation Fund,the CAS(Nos.DNL201912,DNL201915).
文摘Sodium-ion capacitors(SICs)have attracted appreciable attention in virtue of the higher energy and power densities compared with their rivals,supercapacitors and sodium-ion batteries.Due to the lack of sodium resources in cathode,presodiation is critical for SICs to further augment performances.However,current presodiation strategy utilizes metallic sodium as the presodiation material.In this strategy,assembling/disassembling of half-cells is required,which is dangerous and in creases the time and cost of SIC leading to the restriction of their industrialization and commercialization.Herein we present a safe,low-cost and high-efficiency presodiation strategy by first employing Na_(2)C_(2)O_(4) as the sacrificial salt applied in SICs.Na_(2)C_(2)O_(4) is environmentally friendly and possesses considerably low expenditure.No additional residues remain after sodium extraction ascribed to its"zero dead mass"property.When paired with commercial activated carb on as the cathode and commercial hard carbon as the ano de,the constructed pouch-type SICs exhibit high energy and power densities of 91.7 Wh/kg and 13.1 kW/kg,respectively.This work shows a prospect of realizing the safe and low-cost manufacturing for high-performance SICs commercially.
基金Project supported by the National Natural Science Foundation of China(Grant No.61203211)the Natural Science Foundation of Jiangsu Higher Education Institutions of China(Grant No.13KJB140006)the Foundation for Outstanding Young Teachers of Nanjing University of Information Science&Technology,China(Grant No.20110423)
文摘In this paper, we present a high-efficiency S-band gallium nitride （GaN） power amplifier （PA）. This amplifier is fabri- cated based on a self-developed GaN high-electron-mobility transistor （HEMT） with 10 mm gate width on SiC substrate. Harmonic manipulation circuits are presented in the amplifier. The matching networks consist of microstrip lines and discrete components. Open-circuited stub lines in both input and output are used to tune the 2rid harmonic wave and match the GaN HEMT to the highest efficiency condition. The developed amplifier delivers an output power of 48.5 dBm （70 W） with a power-added efficiency （PAE） of 72.2% at 2 GHz in pulse condition. When operating at 1.8-2.2 GHz （20% relative bandwidth）, the amplifier provides an output power higher than 48 dBm （,-~ 65 W）, with a PAE over 70% and a power gain above 15 dB. When operating in continuous-wave （CW） operating conditions, the amplifier gives an output power over 46 dBm （40 W） with PAE beyond 60% over the whole operation frequency range.
