The sublevel top coal caving(SLTCC)mining technology is extensively employed in steeply inclined thick coal seams.Because of the typical characteristics of the short coal face in this mining method,a signifi-cant port...The sublevel top coal caving(SLTCC)mining technology is extensively employed in steeply inclined thick coal seams.Because of the typical characteristics of the short coal face in this mining method,a signifi-cant portion of the top coal is lost at the face end.For reducing the coal loss,the partially reverse drawing technique(PRDT)is proposed as a novel top coal drawing technique.Meanwhile,based on the Bergmark-Roos model(B-R model),a theoretical method for calculating the recovery ratio of top coal based on the top coal boundary equation and residual top coal amount is proposed.The mechanism of PRDT to reduce top coal loss at the face end is revealed by comparing with single-round sequential drawing technique(SSDT).Physical experiments and in-site observation data were used to verify the theoretical model.The results show that PRDT can effectively reduce the amount of residual coal near the roof by optimizing the shape characteristics of top coal boundary.Suggestions for improve recovery ratio in Wudong Coal Mine were given based on its face parameters.展开更多
When mining the fully-mechanized longwall caving face along strike, the unstable equipment, the low top-coal recovery ratio and the difficulty in controlling surrounding rock may occur due to large dip angle. Consider...When mining the fully-mechanized longwall caving face along strike, the unstable equipment, the low top-coal recovery ratio and the difficulty in controlling surrounding rock may occur due to large dip angle. Considering the effects of strike angle on support stability, the ‘‘support-surrounding rock"mechanical models of support topple and support slip were established in this paper. On the basis, the influencing factors of support stability were analyzed and the technical measures of controlling support and surrounding rock stability were put forward. Then the loose particles simulation experiment was conducted to analyze the impacts of caving directions and methods on the top-coal recovery in large dip angle fully-mechanized caving face. Finally, the ‘‘upward sequence and double-openings doublerounds" caving technology was determined. The research results are of great scientific significance and practical values to improve large dip thick seam mining technology.展开更多
Characteristics of gas emission at the K8206 working face in the Third mine of the Yangquan Coal Group were investigated. The effects of strata movement,advancing velocity of working face,production capacity of workin...Characteristics of gas emission at the K8206 working face in the Third mine of the Yangquan Coal Group were investigated. The effects of strata movement,advancing velocity of working face,production capacity of working face and gas extraction capability of strike high-level entry on gas emission at K8206 working face were analyzed. A regression equation,reflecting the relationship between relative gas emission rate and the production capacity of work-ing faces,was established. Another regression equation showing the relationship between the gas emission rate from adjacent layers when the working face was advancing for one metre and advancing velocity was derived. It can be con-cluded that,1) the amount of gas emitted at the K8206 working face is far greater than that of ordinary top coal caving faces with a dip length of 180-190 m; 2) the dynamic process of gas emission from adjacent layers during the initial mining stage is controlled by the movement of key strata; 3) the amount of gas emitted that needs to be forced out by air is greatly affected by the capability of gas extraction; 4) when the advancing velocity is between 3.5-5.5 m/d or when the output is up to 8-12 kt/d,the gas emission from adjacent layers is almost constant.展开更多
Based on the engineering background of gob-side entry retaining in fully-mechanized longwall with top coal caving(GER-FLTC) on N2105 working face of Yuwu coal mine, by adopting the methods of theoretical analysis and ...Based on the engineering background of gob-side entry retaining in fully-mechanized longwall with top coal caving(GER-FLTC) on N2105 working face of Yuwu coal mine, by adopting the methods of theoretical analysis and numerical calculation, the control techniques of surrounding rocks in GER-FLTC working face are studied in this paper. The two main difficulties of stability of surrounding rocks at gob-side retained entry in fully-mechanized longwall working face are the stability control of top coal and control of large deformation of GER-FLTC working face. Interaction mechanical model between roofing and roadside backfilling in GER-FLTC is established and the equations for the calculation of roof-cutting resistance of roadside backfilling are derived. Results of numerical calculation show that the damage zones of top coal can be categorized into the delaminating zone of top coal above the backfilling, tensile damage zone of top coal above the retained roadway and shear damage zone of the upper rib of the solid coal. Stability control of top coal is the critical part to success of GER-FLTC. With consideration of large deformation of surrounding rocks of gob-side retained entry in fully-mechanized longwall, the support technique of‘‘roofing control and wall strengthening'' is proposed where high strength and highly prestressed anchor rods and diagonal tensile anchor cables support are used for top coal, high strength and highly prestressed yielding anchor rod support is used for solid coal and roadside prestressed load-carrying backfilling is constructed by high-water material, in order to maintain the integrity of the top coal, transfer load, high resistance yielding load-carrying of solid coal, roof-cutting of roadside backfilling and support,and to achieve GER-FLTC. Results from this study are successfully applied in engineering practice.展开更多
The thick-san top-ctal catrig technology has been in use in China for over a decade,and has given rise to siguscant economic efficiendes. Eftorts in reeent years to extend its applica tion to more complex mining condi...The thick-san top-ctal catrig technology has been in use in China for over a decade,and has given rise to siguscant economic efficiendes. Eftorts in reeent years to extend its applica tion to more complex mining conditions, mostly high-gas seams , with or without proneness ofspontaneous combustion. have brought about new safety problems This paper will highlight thefcatures and problems retared with thick-seam top-coal caving systems, compared with conventionai, fully-mecbanized longwall systems , particularly issues retated to methane, spontaneous combustion and dust,and disam the methods and measures to ded with them.展开更多
基金supported by the Beijing Natural Science Foundation(No.2232059)the National Natural Science Foundation of China(Nos.52121003,52374148,52204163 and 51934008)+1 种基金the Fundamental Research Funds for the Central Universities(Nos.2023JCCXNY04 and 2023YQTD02)the Open Fund of Key laboratory of Xinjiang Coal Resources Green Mining,Ministry of Education(No.KLXGY-KB2408)。
文摘The sublevel top coal caving(SLTCC)mining technology is extensively employed in steeply inclined thick coal seams.Because of the typical characteristics of the short coal face in this mining method,a signifi-cant portion of the top coal is lost at the face end.For reducing the coal loss,the partially reverse drawing technique(PRDT)is proposed as a novel top coal drawing technique.Meanwhile,based on the Bergmark-Roos model(B-R model),a theoretical method for calculating the recovery ratio of top coal based on the top coal boundary equation and residual top coal amount is proposed.The mechanism of PRDT to reduce top coal loss at the face end is revealed by comparing with single-round sequential drawing technique(SSDT).Physical experiments and in-site observation data were used to verify the theoretical model.The results show that PRDT can effectively reduce the amount of residual coal near the roof by optimizing the shape characteristics of top coal boundary.Suggestions for improve recovery ratio in Wudong Coal Mine were given based on its face parameters.
基金provided by the National Key Basic Research Program of China (973 Program) (No. 2015CB251600)the Qing Lan Projectthe Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD)
文摘When mining the fully-mechanized longwall caving face along strike, the unstable equipment, the low top-coal recovery ratio and the difficulty in controlling surrounding rock may occur due to large dip angle. Considering the effects of strike angle on support stability, the ‘‘support-surrounding rock"mechanical models of support topple and support slip were established in this paper. On the basis, the influencing factors of support stability were analyzed and the technical measures of controlling support and surrounding rock stability were put forward. Then the loose particles simulation experiment was conducted to analyze the impacts of caving directions and methods on the top-coal recovery in large dip angle fully-mechanized caving face. Finally, the ‘‘upward sequence and double-openings doublerounds" caving technology was determined. The research results are of great scientific significance and practical values to improve large dip thick seam mining technology.
基金Projects 50374066 supported by the National Natural Science Foundation of ChinaNCET-05-0478 by the Program for New Century Excellent Talents in University
文摘Characteristics of gas emission at the K8206 working face in the Third mine of the Yangquan Coal Group were investigated. The effects of strata movement,advancing velocity of working face,production capacity of working face and gas extraction capability of strike high-level entry on gas emission at K8206 working face were analyzed. A regression equation,reflecting the relationship between relative gas emission rate and the production capacity of work-ing faces,was established. Another regression equation showing the relationship between the gas emission rate from adjacent layers when the working face was advancing for one metre and advancing velocity was derived. It can be con-cluded that,1) the amount of gas emitted at the K8206 working face is far greater than that of ordinary top coal caving faces with a dip length of 180-190 m; 2) the dynamic process of gas emission from adjacent layers during the initial mining stage is controlled by the movement of key strata; 3) the amount of gas emitted that needs to be forced out by air is greatly affected by the capability of gas extraction; 4) when the advancing velocity is between 3.5-5.5 m/d or when the output is up to 8-12 kt/d,the gas emission from adjacent layers is almost constant.
基金supported by Chinese National Programs for Fundamental Research and Development(973 Program)(2013CB227905)Natural Science Foundation of Jiangsu Province of China(BK20140210)
文摘Based on the engineering background of gob-side entry retaining in fully-mechanized longwall with top coal caving(GER-FLTC) on N2105 working face of Yuwu coal mine, by adopting the methods of theoretical analysis and numerical calculation, the control techniques of surrounding rocks in GER-FLTC working face are studied in this paper. The two main difficulties of stability of surrounding rocks at gob-side retained entry in fully-mechanized longwall working face are the stability control of top coal and control of large deformation of GER-FLTC working face. Interaction mechanical model between roofing and roadside backfilling in GER-FLTC is established and the equations for the calculation of roof-cutting resistance of roadside backfilling are derived. Results of numerical calculation show that the damage zones of top coal can be categorized into the delaminating zone of top coal above the backfilling, tensile damage zone of top coal above the retained roadway and shear damage zone of the upper rib of the solid coal. Stability control of top coal is the critical part to success of GER-FLTC. With consideration of large deformation of surrounding rocks of gob-side retained entry in fully-mechanized longwall, the support technique of‘‘roofing control and wall strengthening'' is proposed where high strength and highly prestressed anchor rods and diagonal tensile anchor cables support are used for top coal, high strength and highly prestressed yielding anchor rod support is used for solid coal and roadside prestressed load-carrying backfilling is constructed by high-water material, in order to maintain the integrity of the top coal, transfer load, high resistance yielding load-carrying of solid coal, roof-cutting of roadside backfilling and support,and to achieve GER-FLTC. Results from this study are successfully applied in engineering practice.
文摘The thick-san top-ctal catrig technology has been in use in China for over a decade,and has given rise to siguscant economic efficiendes. Eftorts in reeent years to extend its applica tion to more complex mining conditions, mostly high-gas seams , with or without proneness ofspontaneous combustion. have brought about new safety problems This paper will highlight thefcatures and problems retared with thick-seam top-coal caving systems, compared with conventionai, fully-mecbanized longwall systems , particularly issues retated to methane, spontaneous combustion and dust,and disam the methods and measures to ded with them.
