The melt stirring in a large copper smelting oxygen bottom-blown furnace is caused by the large amount of gas movement blown in by two rows of oxygen lances.At present,the two rows of oxygen lances provide oxygen of e...The melt stirring in a large copper smelting oxygen bottom-blown furnace is caused by the large amount of gas movement blown in by two rows of oxygen lances.At present,the two rows of oxygen lances provide oxygen of equal strength,and the stirring in the central area of the melt is insufficient,which restricts the efficient progress of the smelting reaction.This study proposes a strong-weak coupling oxygen supply method and establishes an equivalent model based on a large bottom-blown furnace(LBBF)of an enterprise to simulate the bubble characteristics and flow characteristics of the molten pool.The results show that adjusting the flow ratio between the two rows of oxygen lances can create a“strong”and a“weak”coexisting source of disturbance in an LBBF.It is worth noting that when the flow rate ratio of the two rows of oxygen lances is 1.6,the peak velocity generated by the“strong”distur bance source in the molten pool increases by 18.92%,and the disturbance range increases.This method effectively strengthens the stirring in the central area of the molten pool,improves smelting efficiency,and does not produce harmful melt splashes.It provides important guidance for optimizing production practice.展开更多
Ferrite-rich calcium sulfoaluminate(FCSA)cement is often used in special projects such as marine engineering due to its excellent resistance of seawater attack although the cost is a little high.Ground granulated blas...Ferrite-rich calcium sulfoaluminate(FCSA)cement is often used in special projects such as marine engineering due to its excellent resistance of seawater attack although the cost is a little high.Ground granulated blast furnace slag(GGBS),a byproduct of industrial production,is used as a mineral admixture to reduce concrete costs and provide excellent performance.This study aimed to investigate the impact of GGBS on the hydration properties of FCSA cement in seawater.Tests were conducted on heat of hydration,compressive strength,mass change,and pH value of pore solution of FCSA cement paste with a water-to-binder ratio of 0.45.X-ray diffraction(XRD)analysis and thermogravimetric analysis were used to determine the hydration products,while mercury intrusion porosimetry(MIP)was used to measure pore structure.The results indicated that the FCSA cement hydration showed a concentrated heat release at early age.The compressive strength of specimens consistently increased over time,where seawater curing enhanced the compressive strength of control samples.The pH value of pore solution decreased to 10.7−10.9 at 90 d when cured in seawater.The primary hydration products of FCSA cement included ettringite,iron hydroxide gel(FH_(3)),and aluminum hydroxide gel(AH_(3)).Moreover,when cured in seawater,Friedel’s salt was formed,which enhanced the compressive strength of the specimen and increased its coefficient of corrosion.Seawater curing gradually increased sample mass,and GGBS refined pore structure while reducing harmful pore proportions.These results suggest that while GGBS can refine pore structure and improve certain aspects of performance,its inclusion may also reduce compressive strength,highlighting the need for a balanced approach in its use for marine applications.展开更多
As to solve the online monitoring of the inner temperatur e and freezing profile of the reaction shaft of flash smelting furnace, simulation of the wall in the reaction shaft in a flash smelting furnace was made throu...As to solve the online monitoring of the inner temperatur e and freezing profile of the reaction shaft of flash smelting furnace, simulation of the wall in the reaction shaft in a flash smelting furnace was made through numerical computation. The computational results are very near the data got in s ite. The error of the moving boundary is approximately 3%, and that of the tempe rature is less than 5%. It is proved that the simulation software is applicable for practice to monitor the temperature and moving boundary inside the hearth on line. Based on a large number of the data computed, the relation between the cha nge of the moving boundary and inner temperature is summarized, and the great in fluence of the cooling system on the forming and stability of the moving boundar y inside the hearth is emphasized, which provide the theoretical bases for optim izing the flash smelting operation.展开更多
To predict three-dimensional temperature distribution of molten aluminum and its influencing factors inside an industrial aluminum holding furnace,a fluid-solid coupled method was presented.The fluid-solid coupled mat...To predict three-dimensional temperature distribution of molten aluminum and its influencing factors inside an industrial aluminum holding furnace,a fluid-solid coupled method was presented.The fluid-solid coupled mathematics models of aluminum holding furnace in the premixed combustion processing were established based on mass conservation,moment conservation,momentum conservation,energy conservation and chemistry species conservation.Computational results agree well with the test data of the typical condition.The maximum combustion temperature is 1 850 K.The average temperature of the molten aluminum is 1 158 K,and the maximum temperature difference is about 240 K.The average temperature increases 0.3 ℃ while the temperature of combustion air increases 1 ℃.The optimal excess air ratio is 1.25-1.30.展开更多
To simulate the process of electrode operation, a dynamic model describing the electrode system of three-phase electric arc furnace was developed. This new model can be divided into three submodels in terms of the pra...To simulate the process of electrode operation, a dynamic model describing the electrode system of three-phase electric arc furnace was developed. This new model can be divided into three submodels in terms of the practical situation. They are the power supply system model the electric arc model and the hydraulic actuator system model. According to the basic circuit theory, the power supply system model where the high voltage transmission circuit and mutual inductances were considered, was set up. The electric arc model, which was novel for the electrode control, served as the electrical load and was connected to the power supply system model. The hydraulic actuator system model consists of the proportional valve part that is modeled to capture the dead-zone nonlinear characteristics and the hydraulic cylinder part where the impact of the load force is taken into account. By comparing simulation data and actual data, the results show that the electrode system model is proved to be accurate.展开更多
In an anode baking horizontal flue ring furnace, the temperature distribution is one of the key factors influencing the quality of baked anode and is closely correlated with the gas flow. To understand the gas flow di...In an anode baking horizontal flue ring furnace, the temperature distribution is one of the key factors influencing the quality of baked anode and is closely correlated with the gas flow. To understand the gas flow distribution in the flue, Navier Stokes equation with " k ε " two equation turbulence model was adopted and the simulation on the gas flow was performed. The numerical simulation results showed that the even direction of gas flow should be considered in the design of flue baffles and the gas flow distribution was really uneven in the flue in practical use. By adjusting the number and location of flue baffles rationally, the even distribution of gas flow can be improved obviously.展开更多
In this paper, the structure and function of the IDSS in the operation process of electric furnace for cleaning slag are presented and the fuzzy neural network decision model (FNNDM) in the IDSS is specially suggested...In this paper, the structure and function of the IDSS in the operation process of electric furnace for cleaning slag are presented and the fuzzy neural network decision model (FNNDM) in the IDSS is specially suggested. The IDSS possesses selflearning and adaptive properties, and has been used for managing and analyzing the optimal operational conditions since June 1992. Electric energy consumption has been reduced remarkably and the coefficient of recovery of cobalt and nickel has been increased.展开更多
To recover zinc from electric arc furnace(EAF)dust,a process of primary normal pressure leaching and secondary alkaline pressure leaching is proposed.First,under the alkaline pressure leaching system,the experiment of...To recover zinc from electric arc furnace(EAF)dust,a process of primary normal pressure leaching and secondary alkaline pressure leaching is proposed.First,under the alkaline pressure leaching system,the experiment of pure zinc ferrite being reduced by iron powder was carried out.Under the optimal reduction conditions(i.e.,temperature of 260℃,NaOH concentration of 6 mol/L,liquid-to-solid ratio of 50 mL/g,and a 5-fold excess of iron powder),89%of zinc was extracted.The iron in the reduced residue exists as a magnetite phase.Subsequently,the normal pressure leaching experiment was carried out with EAF dust as raw material,and 66%zinc was leached.The main phase of zinc in normal leaching residue was determined to be zinc ferrite.Then,the normal leaching residue was reduced by iron powder under the alkaline pressure leaching system,and 66.5%of zinc was extracted.After the two-stage leaching process,the leaching rate of zinc in EAF dust can achieve 88.7%.The alkaline pressure leaching solution can be returned as the normal pressure leaching solution,and the magnetite in the alkaline pressure leaching residue can be recovered by magnetic separation.展开更多
Taking three-phase electrode adjusting system of submerged arc furnace as study object which has nonlinear, time-variant, multivariable and strong coupling features, a neural adaptive PSD(proportion, sum and different...Taking three-phase electrode adjusting system of submerged arc furnace as study object which has nonlinear, time-variant, multivariable and strong coupling features, a neural adaptive PSD(proportion, sum and differential) dispersive decoupling controller was developed by combining neural adaptive PSD algorithm with dispersive decoupling network. In this work, the production technology process and control difficulties of submerged arc furnace were simply introduced, the necessity of establishing a neural adaptive PSD dispersive decoupling controller was discussed, the design method and the implementation steps of the controller are expounded in detail, and the block diagram of the controlled system is presented. By comparison with experimental results of the conventional PID controller and the adaptive PSD controller, the decoupling ability, adaptive ability, self-learning ability and robustness of the neural adaptive PSD dispersive decoupling controller have been testified effectively. The controller is applicable to the three-phase electrode adjusting system of submerged arc furnace, and it will play an important role for achieving the power balance of three-phrase electrodes, saving energy and reducing consumption in the process of smelting.展开更多
By analyzing the characteristics of combustion and billet heating process, a 3-D transient computer fluid dynamic simulation system based on commercial software CFX4.3 and some self-programmed codes were developed to ...By analyzing the characteristics of combustion and billet heating process, a 3-D transient computer fluid dynamic simulation system based on commercial software CFX4.3 and some self-programmed codes were developed to simulate the thermal process in a continuous heating furnace using high temperature air combustion technology. The effects of different switching modes on injection entrancement of multi burners, combustion and billet heating process in furnace were analyzed numerically, and the computational results were compared with on-site measurement, which verified the practicability of this numerical simulation system. The results indicate that the flow pattern and distribution of temperature in regenerative reheating furnace with partial same-side-switching combustion mode are favorable to satisfy the high quality requirements of reheating, in which the terminal heating temperature of billets is more than 1 460 K and the temperature difference between two nodes is not more than 10 K. But since the surface average temperature of billets apart fi＇om heating zone is only about 1 350 K and continued heating is needed in soaking zone, the design and operation of current state are still needed to be optimized to improve the temperature schedule of billet heating. The distribution of velocity and temperature in regenerative reheating furnace with same-side-switching combustion mode cannot satisfy the even and fast heating process. The terminal heating temperature of billets is lower than that of the former case by 30 K. The distribution of flow and temperature can be improved by using cross-switching combustion mode, whose terminal temperature of billets is about 1 470 K with small temperature difference within 10 K.展开更多
The combustion process of pulverized coal injected into blast furnace involves a lot of physical and chemical reactions. Based on the combustion behaviors of pulverized coal, the conception of coal effective calorific...The combustion process of pulverized coal injected into blast furnace involves a lot of physical and chemical reactions. Based on the combustion behaviors of pulverized coal, the conception of coal effective calorific value representing the actual thermal energy provided for blast furnace was proposed. A cost performance evaluation model of coal injection was built up for the optimal selection of various kinds of coal based on effective calorific value. The model contains two indicators: coal effective calorific value which has eight sub-indicators and coal injection cost which includes four sub-indicators. In addition, the calculation principle and application of cost performance evaluation model in a Chinese large-scale iron and steel company were comprehensively introduced. The evaluation results finally confirm that this novel model is of great significance to the optimal selection of blast furnace pulverized coal.展开更多
A heat transfer model of furnace roller cooling process was established based on analysis of furnace roller＇s structure. The complicated model was solved with iteration planning algorithm based on Newton search. The ...A heat transfer model of furnace roller cooling process was established based on analysis of furnace roller＇s structure. The complicated model was solved with iteration planning algorithm based on Newton search. The model is proved logical and credible by comparing calculated results and measured data. Then, the relationship between water flow velocity, inlet water temperature, furnace temperature and roller cross section temperature, outlet water temperature, water temperature rise, cooling water heat absorption was studied. The conclusions and recommendations are mainly as follows： l） Cooling water temperature rise decreases with the increase of water flow velocity, but it has small relationship with inlet water temperature; 2） In order to get little water scale, inlet water temperature should be controlled below 30 ℃. 3） The cooling water flow velocity should be greater than critical velocity. The critical velocity is 0.07 m/s and water flow velocity should be controlled within 0.4-0.8 m/s. Within this velocity range, water cooling efficiency is high and water temperature rise is little. If cooling water velocity increases again, heat loss will increase, leading to energy wasting.展开更多
For acquiring the details in aluminum holding furnace with bottom porous brick purging system,efforts were performed to try to find out the potential optimal operation schemes.By adopting transient analysis scheme and...For acquiring the details in aluminum holding furnace with bottom porous brick purging system,efforts were performed to try to find out the potential optimal operation schemes.By adopting transient analysis scheme and constant boundary temperature,combustion in the furnace was investigated numerically using computational fluid dynamics(CFD).The predicted gas temperature shows good agreement with the measured results,and the predicted energy distribution of the furnace is consistent with that obtained from energy balance experiment,which confirms the reliability of the numerical solution.The results show that as the fuel-air mixture temperature rises up from 300 K to 500 K,the energy utilization of the furnace could increase from 34.55% to 37.14%.However,as the excess air coefficient increases from 1.0 to 1.4,energy utilization drops from 34.55% to 29.56%.Increasing the combustion temperature is the most effective way to improve the energy efficiency of the furnace.High reactant temperature and medium excess air coefficient are recommended for high operation performance,and keeping the furnace jamb sealed well for avoiding leakage has to be emphasized.展开更多
The traditional prediction methods of element yield rate can be divided into experience method and data-driven method.But in practice,the experience formulae are found to work only under some specific conditions,and t...The traditional prediction methods of element yield rate can be divided into experience method and data-driven method.But in practice,the experience formulae are found to work only under some specific conditions,and the sample data that are used to establish data-driven models are always insufficient.Aiming at this problem,a combined method of genetic algorithm(GA) and adaptive neuro-fuzzy inference system(ANFIS) is proposed and applied to element yield rate prediction in ladle furnace(LF).In order to get rid of the over reliance upon data in data-driven method and act as a supplement of inadequate samples,smelting experience is integrated into prediction model as fuzzy empirical rules by using the improved ANFIS method.For facilitating the combination of fuzzy rules,feature construction method based on GA is used to reduce input dimension,and the selection operation in GA is improved to speed up the convergence rate and to avoid trapping into local optima.The experimental and practical testing results show that the proposed method is more accurate than other prediction methods.展开更多
The temperature control of the large-scale vertical quench furnace is very difficult due to its huge volume and complex thermal exchanges. To meet the technical requirement of the quenching process, a temperature cont...The temperature control of the large-scale vertical quench furnace is very difficult due to its huge volume and complex thermal exchanges. To meet the technical requirement of the quenching process, a temperature control system which integrates temperature calibration and temperature uniformity control is developed for the thermal treatment of aluminum alloy workpieces in the large-scale vertical quench furnace. To obtain the aluminum alloy workpiece temperature, an air heat transfer model is newly established to describe the temperature gradient distribution so that the immeasurable workpiece temperature can be calibrated from the available thermocouple temperature. To satisfy the uniformity control of the furnace temperature, a second order partial differential equation(PDE) is derived to describe the thermal dynamics inside the vertical quench furnace. Based on the PDE, a decoupling matrix is constructed to solve the coupling issue and decouple the heating process into multiple independent heating subsystems. Then, using the expert control rule to find a compromise of temperature rising time and overshoot during the quenching process. The developed temperature control system has been successfully applied to a 31 m large-scale vertical quench furnace, and the industrial running results show the significant improvement of the temperature uniformity, lower overshoot and shortened processing time.展开更多
Physical and chemical properties of electric arc furnace （EAF） dust from Tianjin seamless Pipe Company were measured and analyzed. The zinc leaching tests in alkaline medium were carried out under variation of leach...Physical and chemical properties of electric arc furnace （EAF） dust from Tianjin seamless Pipe Company were measured and analyzed. The zinc leaching tests in alkaline medium were carried out under variation of leaching agent concentration, leaching temperature, leaching cumulative time and solid-to-liquid ratio. The thermodynamics and kinetics of the zinc leaching process were also analyzed. The results show that the EAF dust contains 10% （mass fraction） zinc and the median particle size is 0.69 μm. The zinc recovery of 73.4% is obtained tinder the condition of 90 ℃, 6 mol/L NaOH, and 60 min leaching time. With the increase of concentration of NaOH and the cumulative time, zinc leaching will be significantly increased. The kinetics study demonstrates that the leaching reaction is chemically controlled and the reaction activation energy is 15.73 kJ/mol.展开更多
Using fixed-bed reaction method and changing the gas composition and dust content,the influence of blast furnace top gas composition and dust on HCl removal with low temperature Ca-based antichlor was studied.It was f...Using fixed-bed reaction method and changing the gas composition and dust content,the influence of blast furnace top gas composition and dust on HCl removal with low temperature Ca-based antichlor was studied.It was found that,when the content of CO2 in blast furnace top gas increased,the dechlorination efficiency was getting worse obviously;when the contents of CO and N2 increased,the dechlorination efficiency was getting better to a certain extent;when the content of H2 changed,the dechlorination efficiency got no significant change;as the content of dust increased,the dechlorination efficiency got better obviously when the content was less than 15 g/m3,but it would be got worse quickly when the content was more than 20 g/m3,and the best content was 15–20 g/m3;the suitable site of the process of dechlorination was after gravity dust collector and before bag dust collector.展开更多
In order to know the ventilating capacity of imperial smelt furnace(ISF), and increase the output of plumbum, an intelligent modeling method based on gray theory and artificial neural networks(ANN) is proposed, in whi...In order to know the ventilating capacity of imperial smelt furnace(ISF), and increase the output of plumbum, an intelligent modeling method based on gray theory and artificial neural networks(ANN) is proposed, in which the weight values in the integrated model can be adjusted automatically. An intelligent predictive model of the ventilating capacity of the ISF is established and analyzed by the method. The simulation results and industrial applications demonstrate that the predictive model is close to the real plant, the relative predictive error is 0.72%, which is 50% less than the single model, leading to a notable increase of the output of plumbum.展开更多
The simulation of blast furnace slag was prepared by pure chemical reagents.Test methods like DSC,XRD and SEM were used to study the effect of Al2O3 and MgO content on crystallization of blast furnace slag during fibe...The simulation of blast furnace slag was prepared by pure chemical reagents.Test methods like DSC,XRD and SEM were used to study the effect of Al2O3 and MgO content on crystallization of blast furnace slag during fiber formation.The results show that as Al2O3 and MgO contents in the sample changed,blast furnace slag was crystallized at the average temperature below 1232 K.When the ratio of Mg/Al in the samples is 0.6 calculated by Kissinger equation,crystallization activation energy is at the maximum value and the system is in the most stable condition.The sample crystallization phases are mainly calcium akermanite(2CaO?MgO?2SiO2)and gehlenite(2CaO?Al2O3?SiO2).Secondary crystallization phases are anorthite(CaAl2Si2O8),wollastonite minerals(WOLLA)and pyroxene minerals(cPyrA).Meanwhile,the principal crystallization phases of the samples are different types and have different contents,and the microstructures of the sample sections are different due to the difference between MgO/Al2O3 ratio.展开更多
In order to investigate Joule heating power,a three-dimensional finite element model(FEM) was developed to predict Joule heating power in the channels of double-loop inductor. The simulated results were compared with ...In order to investigate Joule heating power,a three-dimensional finite element model(FEM) was developed to predict Joule heating power in the channels of double-loop inductor. The simulated results were compared with experimental data from low load trials for a 400 kW inductor. The results,such as power factor and Joule heating power,show reasonable correlation with experimental data,and Joule heating rate reaches the maximum at the corners and the minimum at the centre of the cross-section area. With increasing relative permeability of iron core,length of coils,current frequency and resistivity of metal melt,the power factor and Joule heating power change. It is concluded that current frequency,the resistivity and length of the coil play a critical role in determining the power factor and Joule heating power,whereas relative permeability of the magnetic core shows no significant influence on them.展开更多
基金Project(2022YFC3901501)supported by the National Key R&D Program of ChinaProject(U20A20273)supported by the National Natural Science Foundation of China+1 种基金Project(2022JJ10078)supported by the Natural Science Foundation for Distinguished Young Scholars of Hunan Province,ChinaProject(2021RC3005)supported by the Science and Technology Innovation Program of Hunan Province,China。
文摘The melt stirring in a large copper smelting oxygen bottom-blown furnace is caused by the large amount of gas movement blown in by two rows of oxygen lances.At present,the two rows of oxygen lances provide oxygen of equal strength,and the stirring in the central area of the melt is insufficient,which restricts the efficient progress of the smelting reaction.This study proposes a strong-weak coupling oxygen supply method and establishes an equivalent model based on a large bottom-blown furnace(LBBF)of an enterprise to simulate the bubble characteristics and flow characteristics of the molten pool.The results show that adjusting the flow ratio between the two rows of oxygen lances can create a“strong”and a“weak”coexisting source of disturbance in an LBBF.It is worth noting that when the flow rate ratio of the two rows of oxygen lances is 1.6,the peak velocity generated by the“strong”distur bance source in the molten pool increases by 18.92%,and the disturbance range increases.This method effectively strengthens the stirring in the central area of the molten pool,improves smelting efficiency,and does not produce harmful melt splashes.It provides important guidance for optimizing production practice.
基金Project(2023DJC182)supported by the Department of Science and Technology of Hubei Province,ChinaProjects(51608402,51602229)supported by the National Natural Science Foundation of ChinaProject(2021-2075-38)supported by the Department of Housing and Urban-Rural Development of Hubei Province,China。
文摘Ferrite-rich calcium sulfoaluminate(FCSA)cement is often used in special projects such as marine engineering due to its excellent resistance of seawater attack although the cost is a little high.Ground granulated blast furnace slag(GGBS),a byproduct of industrial production,is used as a mineral admixture to reduce concrete costs and provide excellent performance.This study aimed to investigate the impact of GGBS on the hydration properties of FCSA cement in seawater.Tests were conducted on heat of hydration,compressive strength,mass change,and pH value of pore solution of FCSA cement paste with a water-to-binder ratio of 0.45.X-ray diffraction(XRD)analysis and thermogravimetric analysis were used to determine the hydration products,while mercury intrusion porosimetry(MIP)was used to measure pore structure.The results indicated that the FCSA cement hydration showed a concentrated heat release at early age.The compressive strength of specimens consistently increased over time,where seawater curing enhanced the compressive strength of control samples.The pH value of pore solution decreased to 10.7−10.9 at 90 d when cured in seawater.The primary hydration products of FCSA cement included ettringite,iron hydroxide gel(FH_(3)),and aluminum hydroxide gel(AH_(3)).Moreover,when cured in seawater,Friedel’s salt was formed,which enhanced the compressive strength of the specimen and increased its coefficient of corrosion.Seawater curing gradually increased sample mass,and GGBS refined pore structure while reducing harmful pore proportions.These results suggest that while GGBS can refine pore structure and improve certain aspects of performance,its inclusion may also reduce compressive strength,highlighting the need for a balanced approach in its use for marine applications.
文摘As to solve the online monitoring of the inner temperatur e and freezing profile of the reaction shaft of flash smelting furnace, simulation of the wall in the reaction shaft in a flash smelting furnace was made through numerical computation. The computational results are very near the data got in s ite. The error of the moving boundary is approximately 3%, and that of the tempe rature is less than 5%. It is proved that the simulation software is applicable for practice to monitor the temperature and moving boundary inside the hearth on line. Based on a large number of the data computed, the relation between the cha nge of the moving boundary and inner temperature is summarized, and the great in fluence of the cooling system on the forming and stability of the moving boundar y inside the hearth is emphasized, which provide the theoretical bases for optim izing the flash smelting operation.
基金Project(2006AA03Z523) supported by the National High-Tech Research and Development Program of ChinaProject(08C26224302178) supported by the Innovation Foundation of Central South University,China
文摘To predict three-dimensional temperature distribution of molten aluminum and its influencing factors inside an industrial aluminum holding furnace,a fluid-solid coupled method was presented.The fluid-solid coupled mathematics models of aluminum holding furnace in the premixed combustion processing were established based on mass conservation,moment conservation,momentum conservation,energy conservation and chemistry species conservation.Computational results agree well with the test data of the typical condition.The maximum combustion temperature is 1 850 K.The average temperature of the molten aluminum is 1 158 K,and the maximum temperature difference is about 240 K.The average temperature increases 0.3 ℃ while the temperature of combustion air increases 1 ℃.The optimal excess air ratio is 1.25-1.30.
基金Projects(2007AA04Z194, 2007AA041401) supported by the National High-Tech Research and Development Program of China
文摘To simulate the process of electrode operation, a dynamic model describing the electrode system of three-phase electric arc furnace was developed. This new model can be divided into three submodels in terms of the practical situation. They are the power supply system model the electric arc model and the hydraulic actuator system model. According to the basic circuit theory, the power supply system model where the high voltage transmission circuit and mutual inductances were considered, was set up. The electric arc model, which was novel for the electrode control, served as the electrical load and was connected to the power supply system model. The hydraulic actuator system model consists of the proportional valve part that is modeled to capture the dead-zone nonlinear characteristics and the hydraulic cylinder part where the impact of the load force is taken into account. By comparing simulation data and actual data, the results show that the electrode system model is proved to be accurate.
文摘In an anode baking horizontal flue ring furnace, the temperature distribution is one of the key factors influencing the quality of baked anode and is closely correlated with the gas flow. To understand the gas flow distribution in the flue, Navier Stokes equation with " k ε " two equation turbulence model was adopted and the simulation on the gas flow was performed. The numerical simulation results showed that the even direction of gas flow should be considered in the design of flue baffles and the gas flow distribution was really uneven in the flue in practical use. By adjusting the number and location of flue baffles rationally, the even distribution of gas flow can be improved obviously.
文摘In this paper, the structure and function of the IDSS in the operation process of electric furnace for cleaning slag are presented and the fuzzy neural network decision model (FNNDM) in the IDSS is specially suggested. The IDSS possesses selflearning and adaptive properties, and has been used for managing and analyzing the optimal operational conditions since June 1992. Electric energy consumption has been reduced remarkably and the coefficient of recovery of cobalt and nickel has been increased.
基金Project(51504292)supported by National Natural Science Foundation of ChinaProject(2018JJ3678)supported by the Natural Science Foundation of Hunan Province,China。
文摘To recover zinc from electric arc furnace(EAF)dust,a process of primary normal pressure leaching and secondary alkaline pressure leaching is proposed.First,under the alkaline pressure leaching system,the experiment of pure zinc ferrite being reduced by iron powder was carried out.Under the optimal reduction conditions(i.e.,temperature of 260℃,NaOH concentration of 6 mol/L,liquid-to-solid ratio of 50 mL/g,and a 5-fold excess of iron powder),89%of zinc was extracted.The iron in the reduced residue exists as a magnetite phase.Subsequently,the normal pressure leaching experiment was carried out with EAF dust as raw material,and 66%zinc was leached.The main phase of zinc in normal leaching residue was determined to be zinc ferrite.Then,the normal leaching residue was reduced by iron powder under the alkaline pressure leaching system,and 66.5%of zinc was extracted.After the two-stage leaching process,the leaching rate of zinc in EAF dust can achieve 88.7%.The alkaline pressure leaching solution can be returned as the normal pressure leaching solution,and the magnetite in the alkaline pressure leaching residue can be recovered by magnetic separation.
基金Project(61174132) supported by the National Natural Science Foundation of ChinaProject(09JJ6098) supported by the Natural Science Foundation of Hunan Province, China
文摘Taking three-phase electrode adjusting system of submerged arc furnace as study object which has nonlinear, time-variant, multivariable and strong coupling features, a neural adaptive PSD(proportion, sum and differential) dispersive decoupling controller was developed by combining neural adaptive PSD algorithm with dispersive decoupling network. In this work, the production technology process and control difficulties of submerged arc furnace were simply introduced, the necessity of establishing a neural adaptive PSD dispersive decoupling controller was discussed, the design method and the implementation steps of the controller are expounded in detail, and the block diagram of the controlled system is presented. By comparison with experimental results of the conventional PID controller and the adaptive PSD controller, the decoupling ability, adaptive ability, self-learning ability and robustness of the neural adaptive PSD dispersive decoupling controller have been testified effectively. The controller is applicable to the three-phase electrode adjusting system of submerged arc furnace, and it will play an important role for achieving the power balance of three-phrase electrodes, saving energy and reducing consumption in the process of smelting.
基金Project(20010533009) supported by the Special Foundation for Doctorate Discipline of China
文摘By analyzing the characteristics of combustion and billet heating process, a 3-D transient computer fluid dynamic simulation system based on commercial software CFX4.3 and some self-programmed codes were developed to simulate the thermal process in a continuous heating furnace using high temperature air combustion technology. The effects of different switching modes on injection entrancement of multi burners, combustion and billet heating process in furnace were analyzed numerically, and the computational results were compared with on-site measurement, which verified the practicability of this numerical simulation system. The results indicate that the flow pattern and distribution of temperature in regenerative reheating furnace with partial same-side-switching combustion mode are favorable to satisfy the high quality requirements of reheating, in which the terminal heating temperature of billets is more than 1 460 K and the temperature difference between two nodes is not more than 10 K. But since the surface average temperature of billets apart fi＇om heating zone is only about 1 350 K and continued heating is needed in soaking zone, the design and operation of current state are still needed to be optimized to improve the temperature schedule of billet heating. The distribution of velocity and temperature in regenerative reheating furnace with same-side-switching combustion mode cannot satisfy the even and fast heating process. The terminal heating temperature of billets is lower than that of the former case by 30 K. The distribution of flow and temperature can be improved by using cross-switching combustion mode, whose terminal temperature of billets is about 1 470 K with small temperature difference within 10 K.
基金Project(51134008)supported by the National Natural Science Foundation of ChinaProject(2012CB720401)supported by the National Basic Research Program of China
文摘The combustion process of pulverized coal injected into blast furnace involves a lot of physical and chemical reactions. Based on the combustion behaviors of pulverized coal, the conception of coal effective calorific value representing the actual thermal energy provided for blast furnace was proposed. A cost performance evaluation model of coal injection was built up for the optimal selection of various kinds of coal based on effective calorific value. The model contains two indicators: coal effective calorific value which has eight sub-indicators and coal injection cost which includes four sub-indicators. In addition, the calculation principle and application of cost performance evaluation model in a Chinese large-scale iron and steel company were comprehensively introduced. The evaluation results finally confirm that this novel model is of great significance to the optimal selection of blast furnace pulverized coal.
基金Project(2010CB630800) supported by the National Basic Research Program of China
文摘A heat transfer model of furnace roller cooling process was established based on analysis of furnace roller＇s structure. The complicated model was solved with iteration planning algorithm based on Newton search. The model is proved logical and credible by comparing calculated results and measured data. Then, the relationship between water flow velocity, inlet water temperature, furnace temperature and roller cross section temperature, outlet water temperature, water temperature rise, cooling water heat absorption was studied. The conclusions and recommendations are mainly as follows： l） Cooling water temperature rise decreases with the increase of water flow velocity, but it has small relationship with inlet water temperature; 2） In order to get little water scale, inlet water temperature should be controlled below 30 ℃. 3） The cooling water flow velocity should be greater than critical velocity. The critical velocity is 0.07 m/s and water flow velocity should be controlled within 0.4-0.8 m/s. Within this velocity range, water cooling efficiency is high and water temperature rise is little. If cooling water velocity increases again, heat loss will increase, leading to energy wasting.
基金Project(2009GK2009) supported by the Science and Technology Program of Hunan Province,China
文摘For acquiring the details in aluminum holding furnace with bottom porous brick purging system,efforts were performed to try to find out the potential optimal operation schemes.By adopting transient analysis scheme and constant boundary temperature,combustion in the furnace was investigated numerically using computational fluid dynamics(CFD).The predicted gas temperature shows good agreement with the measured results,and the predicted energy distribution of the furnace is consistent with that obtained from energy balance experiment,which confirms the reliability of the numerical solution.The results show that as the fuel-air mixture temperature rises up from 300 K to 500 K,the energy utilization of the furnace could increase from 34.55% to 37.14%.However,as the excess air coefficient increases from 1.0 to 1.4,energy utilization drops from 34.55% to 29.56%.Increasing the combustion temperature is the most effective way to improve the energy efficiency of the furnace.High reactant temperature and medium excess air coefficient are recommended for high operation performance,and keeping the furnace jamb sealed well for avoiding leakage has to be emphasized.
基金Projects(2007AA041401,2007AA04Z194) supported by the National High Technology Research and Development Program of China
文摘The traditional prediction methods of element yield rate can be divided into experience method and data-driven method.But in practice,the experience formulae are found to work only under some specific conditions,and the sample data that are used to establish data-driven models are always insufficient.Aiming at this problem,a combined method of genetic algorithm(GA) and adaptive neuro-fuzzy inference system(ANFIS) is proposed and applied to element yield rate prediction in ladle furnace(LF).In order to get rid of the over reliance upon data in data-driven method and act as a supplement of inadequate samples,smelting experience is integrated into prediction model as fuzzy empirical rules by using the improved ANFIS method.For facilitating the combination of fuzzy rules,feature construction method based on GA is used to reduce input dimension,and the selection operation in GA is improved to speed up the convergence rate and to avoid trapping into local optima.The experimental and practical testing results show that the proposed method is more accurate than other prediction methods.
基金Project(61174132)supported by the National Natural Science Foundation of ChinaProject(2015zzts047)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(20130162110067)supported by the Research Fund for the Doctoral Program of Higher Education of China
文摘The temperature control of the large-scale vertical quench furnace is very difficult due to its huge volume and complex thermal exchanges. To meet the technical requirement of the quenching process, a temperature control system which integrates temperature calibration and temperature uniformity control is developed for the thermal treatment of aluminum alloy workpieces in the large-scale vertical quench furnace. To obtain the aluminum alloy workpiece temperature, an air heat transfer model is newly established to describe the temperature gradient distribution so that the immeasurable workpiece temperature can be calibrated from the available thermocouple temperature. To satisfy the uniformity control of the furnace temperature, a second order partial differential equation(PDE) is derived to describe the thermal dynamics inside the vertical quench furnace. Based on the PDE, a decoupling matrix is constructed to solve the coupling issue and decouple the heating process into multiple independent heating subsystems. Then, using the expert control rule to find a compromise of temperature rising time and overshoot during the quenching process. The developed temperature control system has been successfully applied to a 31 m large-scale vertical quench furnace, and the industrial running results show the significant improvement of the temperature uniformity, lower overshoot and shortened processing time.
基金Project(20876014) supported by the National Natural Science Foundation of China
文摘Physical and chemical properties of electric arc furnace （EAF） dust from Tianjin seamless Pipe Company were measured and analyzed. The zinc leaching tests in alkaline medium were carried out under variation of leaching agent concentration, leaching temperature, leaching cumulative time and solid-to-liquid ratio. The thermodynamics and kinetics of the zinc leaching process were also analyzed. The results show that the EAF dust contains 10% （mass fraction） zinc and the median particle size is 0.69 μm. The zinc recovery of 73.4% is obtained tinder the condition of 90 ℃, 6 mol/L NaOH, and 60 min leaching time. With the increase of concentration of NaOH and the cumulative time, zinc leaching will be significantly increased. The kinetics study demonstrates that the leaching reaction is chemically controlled and the reaction activation energy is 15.73 kJ/mol.
基金Project(51274080)supported by the National Natural Science Foundation of ChinaProject(E2013209051)supported by the Hebei Science Foundation and the Steel and Iron Joint Research Foundation Project,China+1 种基金Project(U1502273)supported by the Joint Funds of the Natural Science Foundation of China and Yunnan Provincial GovernmentProjects(N150202001,N150203003)supported by the Fundamental Research Funds for the Central Universities,China
文摘Using fixed-bed reaction method and changing the gas composition and dust content,the influence of blast furnace top gas composition and dust on HCl removal with low temperature Ca-based antichlor was studied.It was found that,when the content of CO2 in blast furnace top gas increased,the dechlorination efficiency was getting worse obviously;when the contents of CO and N2 increased,the dechlorination efficiency was getting better to a certain extent;when the content of H2 changed,the dechlorination efficiency got no significant change;as the content of dust increased,the dechlorination efficiency got better obviously when the content was less than 15 g/m3,but it would be got worse quickly when the content was more than 20 g/m3,and the best content was 15–20 g/m3;the suitable site of the process of dechlorination was after gravity dust collector and before bag dust collector.
文摘In order to know the ventilating capacity of imperial smelt furnace(ISF), and increase the output of plumbum, an intelligent modeling method based on gray theory and artificial neural networks(ANN) is proposed, in which the weight values in the integrated model can be adjusted automatically. An intelligent predictive model of the ventilating capacity of the ISF is established and analyzed by the method. The simulation results and industrial applications demonstrate that the predictive model is close to the real plant, the relative predictive error is 0.72%, which is 50% less than the single model, leading to a notable increase of the output of plumbum.
基金Project(51474090)supported by the National Natural Science Foundation of China
文摘The simulation of blast furnace slag was prepared by pure chemical reagents.Test methods like DSC,XRD and SEM were used to study the effect of Al2O3 and MgO content on crystallization of blast furnace slag during fiber formation.The results show that as Al2O3 and MgO contents in the sample changed,blast furnace slag was crystallized at the average temperature below 1232 K.When the ratio of Mg/Al in the samples is 0.6 calculated by Kissinger equation,crystallization activation energy is at the maximum value and the system is in the most stable condition.The sample crystallization phases are mainly calcium akermanite(2CaO?MgO?2SiO2)and gehlenite(2CaO?Al2O3?SiO2).Secondary crystallization phases are anorthite(CaAl2Si2O8),wollastonite minerals(WOLLA)and pyroxene minerals(cPyrA).Meanwhile,the principal crystallization phases of the samples are different types and have different contents,and the microstructures of the sample sections are different due to the difference between MgO/Al2O3 ratio.
基金Project(50876116) supported by the National Natural Science Foundation of ChinaProject(2007CK3077) supported by Innovative Program of Hunan Science and Technology AgencyProject(1343-77225) supported by the Graduate School of Central South University
文摘In order to investigate Joule heating power,a three-dimensional finite element model(FEM) was developed to predict Joule heating power in the channels of double-loop inductor. The simulated results were compared with experimental data from low load trials for a 400 kW inductor. The results,such as power factor and Joule heating power,show reasonable correlation with experimental data,and Joule heating rate reaches the maximum at the corners and the minimum at the centre of the cross-section area. With increasing relative permeability of iron core,length of coils,current frequency and resistivity of metal melt,the power factor and Joule heating power change. It is concluded that current frequency,the resistivity and length of the coil play a critical role in determining the power factor and Joule heating power,whereas relative permeability of the magnetic core shows no significant influence on them.
