An optimized device structure for reducing the RESET current of phase-change random access memory （PCRAM） with blade-type like （BTL） phase change layer is proposed. The electrical thermal analysis of the BTL cell ...An optimized device structure for reducing the RESET current of phase-change random access memory （PCRAM） with blade-type like （BTL） phase change layer is proposed. The electrical thermal analysis of the BTL cell and the blade heater contactor structure by three-dimensional finite element modeling are compared with each other during RESET operation. The simulation results show that the programming region of the phase change layer in the BTL cell is much smaller, and thermal electrical distributions of the BTL cell are more concentrated on the TiN/GST interface. The results indicate that the BTL cell has the superiorities of increasing the heating efficiency, decreasing the power consumption and reducing the RESET current from 0.67mA to 0.32mA. Therefore, the BTL cell will be appropriate for high performance PCRAM device with lower power consumption and lower RESET current.展开更多
In this paper, we established a finite element (FEM) model to analyze the dynamic characteristics of arch bridges. In this model, the effects of adjustment to the length of a suspender on its geometry stiffness matrix...In this paper, we established a finite element (FEM) model to analyze the dynamic characteristics of arch bridges. In this model, the effects of adjustment to the length of a suspender on its geometry stiffness matrix are stressed. The FEM equations of mechanics characteristics, natural frequency and main mode are set up based on the first order matrix perturbation theory. Applicantion of the proposed model to analyze a real arch bridge proved the improvement in the simulation precision of dynamical characteristics of the arch bridge by considering the effects of suspender length variation.展开更多
A method of constructing three-dimensional process model for the punching cartridge cases is presented based on DEFORM simulation analysis. Using DEFORM software,the finite element simulation models for the punching a...A method of constructing three-dimensional process model for the punching cartridge cases is presented based on DEFORM simulation analysis. Using DEFORM software,the finite element simulation models for the punching and forming process of cartridge cases are established,and the corresponding simulation result model of each intermediate procedure is obtained by continuously performing the forming process simulation. The simulation model cannot annotate size and process information due to poor interface between DEFORM software and CAD software. Thus,a 3D annotation module is developed with secondary development technology of UG NX software. Consequently,the final process model with dimension and process information is obtained. Then,with the current 3D process management system,the 3D punching and forming process design of cartridge cases can be completed further. An example is also provided to illustrate that the relative error between the simulation process model and the physical model is less than 2%,which proves the validity and reliability of the proposed method in this study.展开更多
A new model is proposed to improve the efficiency of structural modeling. In this model, the bridge structural components are expressed with component description, parametric description and geometric description in a...A new model is proposed to improve the efficiency of structural modeling. In this model, the bridge structural components are expressed with component description, parametric description and geometric description in a software system. This model provides both convenience and flexibility for users in structural modeling process. The object-oriented method is applied in the model implementation. A bridge analysis preprocessor is developed on the basis of this model. It provides an effective way for bridge modeling.展开更多
为准确预报船舶在不同厚度海冰下的阻力性能,基于FEM/SPH(Finite Element Method/Smoothed Particle Hydrodynamics)耦合方法开展不同冰级船舶冰阻力预报研究。采用线弹性与非线性软化相结合的方式构建黏聚单元损伤模型,以冰层厚度为基...为准确预报船舶在不同厚度海冰下的阻力性能,基于FEM/SPH(Finite Element Method/Smoothed Particle Hydrodynamics)耦合方法开展不同冰级船舶冰阻力预报研究。采用线弹性与非线性软化相结合的方式构建黏聚单元损伤模型,以冰层厚度为基础尺寸建立海冰数值模型,通过弯曲强度测试标定相应的力学参数。同时,考虑船舶破冰过程中海水的影响,分别选择低冰级、中冰级和高冰级极地船舶开展破冰过程数值模拟并预报船舶冰阻力。将冰阻力数值计算结果与模型试验结果相对比,结果表明二者的最大偏差不超过12%,证明该数值预报方法可行。展开更多
现有大跨径桥梁有限元模型修正(finite element model updating,FEMU)方法一般未考虑运营荷载对结构动力特性的影响,导致修正后模型的参数变异性大。鉴于此,提出了一种考虑运营荷载的层次贝叶斯有限元模型修正方法,该方法包含考虑温度...现有大跨径桥梁有限元模型修正(finite element model updating,FEMU)方法一般未考虑运营荷载对结构动力特性的影响,导致修正后模型的参数变异性大。鉴于此,提出了一种考虑运营荷载的层次贝叶斯有限元模型修正方法,该方法包含考虑温度和交通荷载的概率参数修正、概率响应预测和结构状态评估。首先,根据监测数据的相关性分析结果确定了计算理论频率时需要考虑的荷载。随后,建立了温度-弹性模量线性关系,并基于动态称重(weigh-in-motion,WIM)数据,提出一种车辆荷载估计方法,以在有限元模型中定量考虑运营荷载对结构频率的影响。同时,引入两阶段马尔科夫链蒙特卡洛(Markov chain Monte Carlo,MCMC)采样方法和响应面代理模型,以提高概率模型修正的计算速率。该方法在一座采集了两年监测数据的大跨径拱桥上得到了验证。结果表明,在考虑运营荷载、参数不确定性和建模误差后,实测频率基本处于预测频率的95%置信区间内。最后,基于实测响应和预测响应置信区间提出了一个结构状态指标,并利用该指标检测出该桥的路面铺装更换过程。展开更多
基金Supported by the Strategic Priority Research Program of the Chinese Academy of Sciences under Grant No XDA09020402the National Integrate Circuit Research Program of China under Grant No 2009ZX02023-003+1 种基金the National Natural Science Foundation of China under Grant Nos 61261160500,61376006,61401444 and 61504157the Science and Technology Council of Shanghai under Grant Nos 14DZ2294900,15DZ2270900 and 14ZR1447500
文摘An optimized device structure for reducing the RESET current of phase-change random access memory （PCRAM） with blade-type like （BTL） phase change layer is proposed. The electrical thermal analysis of the BTL cell and the blade heater contactor structure by three-dimensional finite element modeling are compared with each other during RESET operation. The simulation results show that the programming region of the phase change layer in the BTL cell is much smaller, and thermal electrical distributions of the BTL cell are more concentrated on the TiN/GST interface. The results indicate that the BTL cell has the superiorities of increasing the heating efficiency, decreasing the power consumption and reducing the RESET current from 0.67mA to 0.32mA. Therefore, the BTL cell will be appropriate for high performance PCRAM device with lower power consumption and lower RESET current.
基金Supported by the Key Teacher Foundation of Chongqing University (No. 717411067)
文摘In this paper, we established a finite element (FEM) model to analyze the dynamic characteristics of arch bridges. In this model, the effects of adjustment to the length of a suspender on its geometry stiffness matrix are stressed. The FEM equations of mechanics characteristics, natural frequency and main mode are set up based on the first order matrix perturbation theory. Applicantion of the proposed model to analyze a real arch bridge proved the improvement in the simulation precision of dynamical characteristics of the arch bridge by considering the effects of suspender length variation.
基金Supported by the National Defense Basic Scientific Research Project(A1020131011)
文摘A method of constructing three-dimensional process model for the punching cartridge cases is presented based on DEFORM simulation analysis. Using DEFORM software,the finite element simulation models for the punching and forming process of cartridge cases are established,and the corresponding simulation result model of each intermediate procedure is obtained by continuously performing the forming process simulation. The simulation model cannot annotate size and process information due to poor interface between DEFORM software and CAD software. Thus,a 3D annotation module is developed with secondary development technology of UG NX software. Consequently,the final process model with dimension and process information is obtained. Then,with the current 3D process management system,the 3D punching and forming process design of cartridge cases can be completed further. An example is also provided to illustrate that the relative error between the simulation process model and the physical model is less than 2%,which proves the validity and reliability of the proposed method in this study.
文摘A new model is proposed to improve the efficiency of structural modeling. In this model, the bridge structural components are expressed with component description, parametric description and geometric description in a software system. This model provides both convenience and flexibility for users in structural modeling process. The object-oriented method is applied in the model implementation. A bridge analysis preprocessor is developed on the basis of this model. It provides an effective way for bridge modeling.
文摘为准确预报船舶在不同厚度海冰下的阻力性能,基于FEM/SPH(Finite Element Method/Smoothed Particle Hydrodynamics)耦合方法开展不同冰级船舶冰阻力预报研究。采用线弹性与非线性软化相结合的方式构建黏聚单元损伤模型,以冰层厚度为基础尺寸建立海冰数值模型,通过弯曲强度测试标定相应的力学参数。同时,考虑船舶破冰过程中海水的影响,分别选择低冰级、中冰级和高冰级极地船舶开展破冰过程数值模拟并预报船舶冰阻力。将冰阻力数值计算结果与模型试验结果相对比,结果表明二者的最大偏差不超过12%,证明该数值预报方法可行。
文摘现有大跨径桥梁有限元模型修正(finite element model updating,FEMU)方法一般未考虑运营荷载对结构动力特性的影响,导致修正后模型的参数变异性大。鉴于此,提出了一种考虑运营荷载的层次贝叶斯有限元模型修正方法,该方法包含考虑温度和交通荷载的概率参数修正、概率响应预测和结构状态评估。首先,根据监测数据的相关性分析结果确定了计算理论频率时需要考虑的荷载。随后,建立了温度-弹性模量线性关系,并基于动态称重(weigh-in-motion,WIM)数据,提出一种车辆荷载估计方法,以在有限元模型中定量考虑运营荷载对结构频率的影响。同时,引入两阶段马尔科夫链蒙特卡洛(Markov chain Monte Carlo,MCMC)采样方法和响应面代理模型,以提高概率模型修正的计算速率。该方法在一座采集了两年监测数据的大跨径拱桥上得到了验证。结果表明,在考虑运营荷载、参数不确定性和建模误差后,实测频率基本处于预测频率的95%置信区间内。最后,基于实测响应和预测响应置信区间提出了一个结构状态指标,并利用该指标检测出该桥的路面铺装更换过程。
