In this work,the effect of ultrasonic vibration modes on the mechanical properties and relaxation of residual stress in 6061-T6 aluminum alloy was studied.A new ultrasonic vibration Johnson-Cook model was proposed,and...In this work,the effect of ultrasonic vibration modes on the mechanical properties and relaxation of residual stress in 6061-T6 aluminum alloy was studied.A new ultrasonic vibration Johnson-Cook model was proposed,and the relaxation and distribution of residual stress under ultrasonic vibration were predicted and analyzed using the finite element method(FEM).The mechanical properties of 6061-T6 aluminum alloy under different ultrasonic vibration modes were analyzed through experiments involving notched specimen tensile testing and scanning electron microscopy(SEM)analysis.The findings indicate that ultrasonic vibration treatment during deformation,unloading,and load-holding,as well as treatment with its natural ultrasonic frequency,can effectively release residual stress;however,treatment with its natural frequency has the highest rate of release up to 65.4%.Ultrasonic vibration treatment during deformation better inhibits fracture under the same conditions.The FEM results are in good agreement with the experimental results,and it can be used as a valid tool for predicting residual stress release under ultrasonic vibration.展开更多
The compaction and stress generation on terrain were always investigated based on empirical approaches or testing methods for tire/soil interaction.However,the analysis should be performed for various tires and at dif...The compaction and stress generation on terrain were always investigated based on empirical approaches or testing methods for tire/soil interaction.However,the analysis should be performed for various tires and at different soil strengths.With the increasing capacity of numerical computers and simulation software,finite element modeling of tire/terrain interaction seems a good approach for predicting the effect of change on the parameters.In this work,an elaborated 3D model fully complianning with the geometry of radial tire 115/60R13 was established,using commercial code Solidwork Simulation.The hyper-elastic and incompressible rubber as tire main material was analyzed by Moony-Rivlin model.The Drucker-Prager yield criterion was used to model the soil compaction.Results show that the model realistically predicts the laboratory tests outputs of the modeled tire on the soft soil.展开更多
Practical experiences gained in the past several years show that the thermal residual stress(TRS) is a main cause leading polycrystalline diamond compacts(PDC) to premature failure.It is the very important to measure ...Practical experiences gained in the past several years show that the thermal residual stress(TRS) is a main cause leading polycrystalline diamond compacts(PDC) to premature failure.It is the very important to measure the TRS accurately for optimizing the interface and improving the service performance of PDC.In this paper,the TRS in 1913 flat-interface PDC was measured using improved stress-release method(ISRM). The TRS on the surface of polycrystalline diamond(PCD) table was obtained,which can be used to calculate the radial thermal residual stress(RTRS) at the interface of PCD table via a refutation process.The obtained results show that there are compressive residual stress at the PCD table interface and in the most region of PCD table surface.The exception occurs near the outer diameter of the PCD table,where the PDC begins to bend and put the PCD table surface into a tension state,an undesirable state for a brittle material.The ISRM has covered the shortage existing in traditional stress-release method,in which only finite points on the surface of PCD table can be tested for one specimen and one time.Simple as the experimental procedures are,the test results are also very accurate and reliable.This method provides the theoretical and experimental basis for testing TRS of PDC accurately.展开更多
针对以往有限元模型中弹丸数量较少且为规则阵列排布的缺陷,采用光滑粒子流体动力学法(Smoothed particle hydrodynamics,SPH)与有限元法(Finite element method,FEM)相结合的方法,对喷丸过程进行数值模拟;使用MATLAB对弹丸空间位置坐...针对以往有限元模型中弹丸数量较少且为规则阵列排布的缺陷,采用光滑粒子流体动力学法(Smoothed particle hydrodynamics,SPH)与有限元法(Finite element method,FEM)相结合的方法,对喷丸过程进行数值模拟;使用MATLAB对弹丸空间位置坐标进行随机化处理,形成了大量丸粒冲击工件表面的随机喷丸仿真模型。通过分析确定了喷丸饱和时间,研究了喷射角度、弹丸流量对残余应力场的影响。结果表明:在喷丸参数一定的条件下,存在相应的饱和喷丸时间;研究喷丸参数对残余应力的影响时,应在喷丸达到饱和时间之后提取残余应力值;喷射角度增大,残余压应力增大;开始时弹丸流量增大,残余压应力会有所增大,但当其达到饱和值后,残余压应力不再变化。展开更多
基金Project(51775480)supported by the National Natural Science Foundation of ChinaProjects(E2018203143,E2022203050)supported by the Natural Science Foundation of Hebei Province,China。
文摘In this work,the effect of ultrasonic vibration modes on the mechanical properties and relaxation of residual stress in 6061-T6 aluminum alloy was studied.A new ultrasonic vibration Johnson-Cook model was proposed,and the relaxation and distribution of residual stress under ultrasonic vibration were predicted and analyzed using the finite element method(FEM).The mechanical properties of 6061-T6 aluminum alloy under different ultrasonic vibration modes were analyzed through experiments involving notched specimen tensile testing and scanning electron microscopy(SEM)analysis.The findings indicate that ultrasonic vibration treatment during deformation,unloading,and load-holding,as well as treatment with its natural ultrasonic frequency,can effectively release residual stress;however,treatment with its natural frequency has the highest rate of release up to 65.4%.Ultrasonic vibration treatment during deformation better inhibits fracture under the same conditions.The FEM results are in good agreement with the experimental results,and it can be used as a valid tool for predicting residual stress release under ultrasonic vibration.
文摘The compaction and stress generation on terrain were always investigated based on empirical approaches or testing methods for tire/soil interaction.However,the analysis should be performed for various tires and at different soil strengths.With the increasing capacity of numerical computers and simulation software,finite element modeling of tire/terrain interaction seems a good approach for predicting the effect of change on the parameters.In this work,an elaborated 3D model fully complianning with the geometry of radial tire 115/60R13 was established,using commercial code Solidwork Simulation.The hyper-elastic and incompressible rubber as tire main material was analyzed by Moony-Rivlin model.The Drucker-Prager yield criterion was used to model the soil compaction.Results show that the model realistically predicts the laboratory tests outputs of the modeled tire on the soft soil.
基金supported by the Natural Science of Hunan(06JJ4062)
文摘Practical experiences gained in the past several years show that the thermal residual stress(TRS) is a main cause leading polycrystalline diamond compacts(PDC) to premature failure.It is the very important to measure the TRS accurately for optimizing the interface and improving the service performance of PDC.In this paper,the TRS in 1913 flat-interface PDC was measured using improved stress-release method(ISRM). The TRS on the surface of polycrystalline diamond(PCD) table was obtained,which can be used to calculate the radial thermal residual stress(RTRS) at the interface of PCD table via a refutation process.The obtained results show that there are compressive residual stress at the PCD table interface and in the most region of PCD table surface.The exception occurs near the outer diameter of the PCD table,where the PDC begins to bend and put the PCD table surface into a tension state,an undesirable state for a brittle material.The ISRM has covered the shortage existing in traditional stress-release method,in which only finite points on the surface of PCD table can be tested for one specimen and one time.Simple as the experimental procedures are,the test results are also very accurate and reliable.This method provides the theoretical and experimental basis for testing TRS of PDC accurately.
文摘针对以往有限元模型中弹丸数量较少且为规则阵列排布的缺陷,采用光滑粒子流体动力学法(Smoothed particle hydrodynamics,SPH)与有限元法(Finite element method,FEM)相结合的方法,对喷丸过程进行数值模拟;使用MATLAB对弹丸空间位置坐标进行随机化处理,形成了大量丸粒冲击工件表面的随机喷丸仿真模型。通过分析确定了喷丸饱和时间,研究了喷射角度、弹丸流量对残余应力场的影响。结果表明:在喷丸参数一定的条件下,存在相应的饱和喷丸时间;研究喷丸参数对残余应力的影响时,应在喷丸达到饱和时间之后提取残余应力值;喷射角度增大,残余压应力增大;开始时弹丸流量增大,残余压应力会有所增大,但当其达到饱和值后,残余压应力不再变化。
