Due to the presence of nitro groups, the dust generated during the production and utilization of energetic materials may potentially lead to dust explosion even under low-oxygen or anaerobic conditions.Considering the...Due to the presence of nitro groups, the dust generated during the production and utilization of energetic materials may potentially lead to dust explosion even under low-oxygen or anaerobic conditions.Considering the high energy density of energetic materials, dust explosion can cause serious production safety accidents. Therefore, it is necessary to understand the dust explosion characteristics of energetic materials and the mechanism of dust explosion. According to the literature review, among various influencing factors, the physical and chemical properties of dust are the decisive factors affecting the explosion characteristics of dust. In addition to experimental studies, numerical simulation is another important tool. However, it is subjected to certain limitations. Moreover, it is essential but challenging to fully understand the underlying mechanism. In addition, given the safety hazards posed by dust explosion, explosion suppression has attracted extensive attention for research. Depending on the medium used, there are different forms of suppression, including powder explosion suppression, water spray explosion suppression, inert gas explosion suppression, porous material explosion suppression, and vacuum chamber explosion suppression. As for the selection of explosion suppression agent, consideration must be given to the characteristics of the material. Furthermore, the above research has laid a foundation for discussing the future progress in studying dust explosion of energetic materials, with nano dust and the constraints of existing technology as the focal point.展开更多
RDX/Al mixtures are widely utilized in energetic materials,yet their hybrid dust generated during production and application poses potential explosion hazards.Moreover,the synergistic explosion mechanisms remain poorl...RDX/Al mixtures are widely utilized in energetic materials,yet their hybrid dust generated during production and application poses potential explosion hazards.Moreover,the synergistic explosion mechanisms remain poorly understood,particularly at varying dust concentrations.This study systematically investigates the effects of different aluminum powder mass percentages and dust concentrations(300 g/m^(3),600 g/m^(3),900 g/m^(3))on RDX dust explosion severity,flame propagation behavior,and gaseous products.The results indicate that the maximum explosion pressure peaks at 35%RDX,65%RDX,and 80%RDX at 300 g/m^(3),600 g/m^(3),and 900 g/m^(3),respectively.Concurrently,the time for the flame to propagate to the wall(t1)reaches minimum values of 34.8 ms,25.66 ms,and 23.93 ms.The maximum rate of pressure rise is observed for pure RDX at 900 g/m^(3).Aluminum powder enhances flame propagation velocity and combustion duration,as validated by the flame propagation system.Overall,the concentrations of carbon oxides(CO+CO_(2))decrease significantly with increasing aluminum mass percentage.At 20%RDX,the concentrations decreased by 51.64%,72.31%,and 79.55%compared to pure RDX at 300 g/m^(3),600 g/m^(3),and 900 g/m^(3),respectively.Notably,N_(2)O concentration only at 300 g/m^(3)showed such a trend.It rises first and then falls at 35%RDX at 600 g/m^(3)and 900 g/m^(3).These findings elucidate the synergistic explosion mechanisms and provide critical guidelines for safe production and handling.展开更多
Urban growth has promoted the use of underground spaces,where explosion accidents can be catastrophic.In this study,we investigated the effect of placing flexible construction in front of rigid obstacles on methane ex...Urban growth has promoted the use of underground spaces,where explosion accidents can be catastrophic.In this study,we investigated the effect of placing flexible construction in front of rigid obstacles on methane explosion protection by using an experimental platform and adjusting the blockage rate and spacing of the obstacles.It aims to reduce the risk of gas explosions in urban underground spaces.The results of the study show that the flame propagation peak speed and peak overpressure are reduced with the decrease in the blocking rate of the flexible obstacle when the blocking rate of the flexible obstacle is less than or equal to the blocking rate of the rigid obstacle,with the decrease in the spacing,the better the protection effect of the methane explosion.When the blockage rate of the flexible obstacle is greater than the blockage rate of the rigid obstacle and spacing is less than the height of the flexible obstacle,rigid and flexible obstacles are connected as a whole,increasing the strength of the explosion.This study can provide a theoretical basis and scientific guidance for optimizing rigid and flexible object hybrid layouts and methane explosion protection technology in urban underground spaces.展开更多
Gas explosion in confined space often leads to significant pressure oscillation.It is widely recognized that structural damage can be severe when the oscillation frequency of the load resonates with the natural vibrat...Gas explosion in confined space often leads to significant pressure oscillation.It is widely recognized that structural damage can be severe when the oscillation frequency of the load resonates with the natural vibration frequency of the structure.To reveal the oscillation mechanism of gas explosion load,the experiment of gas explosion was conducted in a large-scale confined tube with the length of 30 m,and the explosion process was numerically analyzed using FLACS.The results show that the essential cause of oscillation effect is the reflection of the pressure wave.In addition,due to the difference in the propagation path of the pressure wave,the load oscillation frequency at the middle position of the tunnel is twice that at the end position.The average sound velocity can be used to calculate the oscillation frequency of overpressure accurately,and the error is less than 15%.The instability of the flame surface and the increase of flame turbulence caused by the interaction between the pressure wave and the flame surface are the main contributors to the increase in overpressure and amplitude.The overpressure peaks calculated by the existing flame instability model and turbulence disturbance model are 31.7%and 34.7%lower than the numerical results,respectively.The turbulence factor model established in this work can describe the turbulence enhancement effect caused by flame instability and oscillatory load,and the difference between the theoretical and numerical results is only 4.6%.In the theoretical derivation of the overpressure model,an improved model of dynamic turbulence factor is established,which can describe the enhancement effect of turbulence factor caused by flame instability and self-turbulence.Based on the one-dimensional propagation theory of pressure wave,the oscillatory effect of the load is derived to calculate the frequency and amplitude of pressure oscillation.The average error of amplitude and frequency is less than 20%.展开更多
The gas explosion in residential building has always been a highly concerned problem.Explosions in homogeneous mixtures have been extensively studied.However,mixtures are often inhomogeneous in the practical scenarios...The gas explosion in residential building has always been a highly concerned problem.Explosions in homogeneous mixtures have been extensively studied.However,mixtures are often inhomogeneous in the practical scenarios due to the differences in the densities of methane and air.In order to investigate the effects of gas explosions in inhomogeneous mixtures,experimental studies involving gas leakage and explosion are conducted in a full-scale residential building to reproduce the process of gas explosion.By fitting the dimensionless buoyancy as a function of dimensionless height and dimensionless time,a distribution model of gas in large-scale spaces is established,and the mechanism of inhomogeneous distribution of methane is also be revealed.Furthermore,the stratified reconstruction method(SRM)is introduced for efficiently setting up inhomogeneous concentration fields in FLACS.The simulation results highlight that for the internal overpressure,the distribution of methane has no effect on the first overpressure peak(ΔP1),while it significantly influences the subsequent overpressure peak(ΔP2),and the maximum difference between the overpressure of homogeneous and inhomogeneous distribution is174.3%.Moreover,the initial concentration distribution also has a certain impact on the external overpressure.展开更多
The internal and external flow fields during vented explosions of methane were characterized through numerical simulation,and the capability of numerical simulation thereof was validated by previous experimental data ...The internal and external flow fields during vented explosions of methane were characterized through numerical simulation,and the capability of numerical simulation thereof was validated by previous experimental data at three ignition positions.The venting mechanism was revealed by the simulated concentration distribution,temperature profile,and airflow velocity.The results show rear ignition results in the external methane mass distribution taking the form of"mushroom"and columnar flames in the external space,which can be expressed as a third-order polynomial relationship with distance;central ignition forms a relationship of the form y=AxB.Front ignition causes the temperature to show a tendency to repeated oscillations(rising,falling,and rising).Central ignition generates the maximum vented airflow velocity(V_(max)=320 m/s)upon vent opening.The results indicate that it is acceptable to apply numerical simulation of methane explosions in practice.展开更多
The afterburning of TNT and structural constraints in confined spaces significantly amplify the blast load,leading to severe structural damage. This study investigates the mechanisms underlying the enhanced dynamic re...The afterburning of TNT and structural constraints in confined spaces significantly amplify the blast load,leading to severe structural damage. This study investigates the mechanisms underlying the enhanced dynamic response of reinforced concrete blast doors with four-sided restraints in confined space. Explosion tests with TNT charges ranging from 0.15 kg to 0.4 kg were conducted in a confined space,capturing overpressure loads and the dynamic response of the blast door. An internal explosion model incorporating the afterburning effect was developed using LS-DYNA software and validated against experimental data. The results reveal that the TNT afterburning effect amplifies both the initial peak overpressure and the quasi-static overpressure, resulting in increased deformation of the blast door.Within the 0.15-0.4 kg charge range, the initial overpressure peak and quasi-static overpressure increased by an average of 1.79 times and 2.21 times, respectively. Additionally, the afterburning effect enhanced the blast door's deflection by 177%. Compared to open-space scenarios, the cumulative deflection of the blast door due to repeated shock wave impacts is significantly greater in confined spaces. Furthermore, the quasi-static pressure arising from the structural constraints sustains the blast door's deflection at a high level.展开更多
Investigating the blast effects and mechanisms on typical finite-sized obstacles is essential for optimizing defense strategies and designing more robust barriers to deter terrorists and protect critical locations.Thi...Investigating the blast effects and mechanisms on typical finite-sized obstacles is essential for optimizing defense strategies and designing more robust barriers to deter terrorists and protect critical locations.This study investigates the blasting effects and underlying mechanisms of concrete frustums subjected to contact explosions,employing both numerical simulations and field tests.It focuses on the effects of top and side blasting,with particular emphasis on fracture modes,damage patterns,and fragment sizes,as well as the causes of different failure modes and the propagation of stress waves.The study also explores the blasting effects of detonating explosives at varying positions along the side and with different charge amounts.The results show that side-blasting leads to complete fragmentation,with tensile waves playing a significant role in creating extensive damage zones that propagate parallel to the frustum's outer surface,concentrating damage near the surface.During top-blasting,the upper half of the frustum undergoes fragmentation,while the lower half experiences cracking.Tensile waves propagate from the top to the bottom surface,forming larger blocks in regions with lower wave intensity.Three distinct damage zones within the frustum were identified,and a series of mathematical formulas were derived to describe the relationship between the maximum fragment size and charge mass.As the charge mass increased from 1.0 kg to 4.0 kg,the maximum fragment size decreased.Detonation at the center of the frustum's side resulted in the most severe fragmentation,with a 51.8%reduction in fragment size compared to other detonation positions.Finally,four broken modes were classified,each influenced by charge mass and explosive location.This study provides valuable insights for optimizing civil blasting operations and designing protective engineering structures.展开更多
To investigate the explosion load characteristics and structural response law in a water mist environment in a cabin,explosion experiments are carried out.The weakening rates of the initial peak overpressure,quasistat...To investigate the explosion load characteristics and structural response law in a water mist environment in a cabin,explosion experiments are carried out.The weakening rates of the initial peak overpressure,quasistatic pressure and structural residual deflection increase with increasing working pressure of the water mist nozzle.Specifically,the weakening rate of the initial peak overpressure ranges from 7.8%to 31.0%,the quasistatic pressure weakening rate ranges from 29.2%to 41.0%,and the weakening rate of the center of the plate residual deflection ranges from 10.8%to 34.4%under the various working pressures of the nozzles.To further explore the effect of water mist explosion suppression,a method for three-dimensional numerical simulations of water mist weakening the explosion shock wave is established to explore the explosion load characteristics of the compartment and the bulkhead response law.On the basis of the dimension analysis method,empirical formulas are derived to predict the residual deflection thickness in the center of the bulkheads.These findings provide the fundamental basis for the appli-cation of water mist in anti-explosive protection.展开更多
Shock wave caused by a sudden release of high-energy,such as explosion and blast,usually affects a significant range of areas.The utilization of a uniform fine mesh to capture sharp shock wave and to obtain precise re...Shock wave caused by a sudden release of high-energy,such as explosion and blast,usually affects a significant range of areas.The utilization of a uniform fine mesh to capture sharp shock wave and to obtain precise results is inefficient in terms of computational resource.This is particularly evident when large-scale fluid field simulations are conducted with significant differences in computational domain size.In this work,a variable-domain-size adaptive mesh enlargement(vAME)method is developed based on the proposed adaptive mesh enlargement(AME)method for modeling multi-explosives explosion problems.The vAME method reduces the division of numerous empty areas or unnecessary computational domains by adaptively suspending enlargement operation in one or two directions,rather than in all directions as in AME method.A series of numerical tests via AME and vAME with varying nonintegral enlargement ratios and different mesh numbers are simulated to verify the efficiency and order of accuracy.An estimate of speedup ratio is analyzed for further efficiency comparison.Several large-scale near-ground explosion experiments with single/multiple explosives are performed to analyze the shock wave superposition formed by the incident wave,reflected wave,and Mach wave.Additionally,the vAME method is employed to validate the accuracy,as well as to investigate the performance of the fluid field and shock wave propagation,considering explosive quantities ranging from 1 to 5 while maintaining a constant total mass.The results show a satisfactory correlation between the overpressure versus time curves for experiments and numerical simulations.The vAME method yields a competitive efficiency,increasing the computational speed to 3.0 and approximately 120,000 times in comparison to AME and the fully fine mesh method,respectively.It indicates that the vAME method reduces the computational cost with minimal impact on the results for such large-scale high-energy release problems with significant differences in computational domain size.展开更多
In this study, we focused on the effect of the underwater explosion parameters of multi-point array explosion. The shock wave and bubble parameters of aggregate charge, two charges, and four charges were measured thro...In this study, we focused on the effect of the underwater explosion parameters of multi-point array explosion. The shock wave and bubble parameters of aggregate charge, two charges, and four charges were measured through an underwater explosion test, and their influence on the explosion power field of charge quantity and array distance was analyzed. Results show that the multi-shock wave collision of array explosion can be approximated to a linear superposition, and the interaction of delayed shock wave can be deemed as the increase of the shock wave baseline. Shock wave focusing and delayed superposition increase the shock wave peak pressure. Compared with the aggregate charge, the greater the number of array explosion points is, the higher the impulse and the gain of the bubble peak pressure are. At the same array distance, the smaller the charge quantity is, the higher the bubble impulse will be. At the same charge quantity, the smaller the array distance is, the higher the bubble impulse will be. The bubble period decreases gradually with the increase of the charge quantity, but the test orientation has little effect on the bubble period.展开更多
While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and ...While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and numerical study has been carried out to characterize the effect of SCW on transferred impulse and loading magnitude of shallow buried explosives.Firstly,blast tests of shallow buried explosives were conducted,with and without the SCW,to quantitatively assess the blast loading impulse.Subsequently,finite element(FE)simulations were performed and validated against experimental measurement,with good agreement achieved.The validated FE model was then employed to predict the dynamic response of a fully-clamped metallic circular target,subjected to the explosive impact of shallow buried explosives with SCW,and explore the corresponding physical mechanisms.It was demonstrated that shallow buried explosives in saturated soil generate a greater impulse transferred towards the target relative to those in dry soil.The deformation displacement of the target plate is doubled.Increasing the height of SCW results in enhanced center peak deflection of the loaded target,accompanied by subsequent fall,due to the variation of deformation pattern of the loaded target from concentrated load to uniform load.Meanwhile,the presence of SCW increases the blast impulse transferred towards the target by three times.In addition,there exists a threshold value of the burial depth that maximizes the impact impulse.This threshold exhibits a strong sensitivity to SCW height,decreasing with increasing SCW height.An empirical formula for predicting threshold has been provided.Similar conclusions can be drawn for different explosive masses.The results provide technical guidance on blast loading intensity and its spatial distribution considering shallow buried explosives in coast-land battlefields,which can ultimately contribute to better protective designs.展开更多
In the study,the two-color pyrometer technique was used to measure the transient temperature field of emulsion explosives with different contents of TiH_(2)powders.The experimental results showed that the introduction...In the study,the two-color pyrometer technique was used to measure the transient temperature field of emulsion explosives with different contents of TiH_(2)powders.The experimental results showed that the introduction of TiH_(2)powders could significantly increase the explosion temperature and fireball duration of emulsion explosive.When emulsion explosives were ignited,the average explosion temperature of pure emulsion explosive continuously decreased while emulsion explosives added with TiH_(2)powders increased at first and then decreased.When the content of TiH_(2)powders was 6 mass%,the explosion average temperature reached its maximum value of 3095 K,increasing by 43.7%as compared with that of pure emulsion explosive.In addition,the results of air blast experiment and explosion heat test showed that the variation trends of shock wave parameters,explosion heat and theoretical explosion temperature of emulsion explosives with different contents of TiH_(2)powders were basically consistent with that of explosion temperature measured by the two-color pyrometer technique.In conclusion,the two-color pyrometer technique would be conducive to the formula design of emulsion explosive by understanding the explosion temperature characteristics.展开更多
Measuring the dust explosion characteristics of aluminum-based activated fuels was a prerequisite for developing effective prevention and control measures.In this paper,ignition sensitivity,flame propagation behaviors...Measuring the dust explosion characteristics of aluminum-based activated fuels was a prerequisite for developing effective prevention and control measures.In this paper,ignition sensitivity,flame propagation behaviors and explosion severity of aluminum/polytetrafluoroethylene(Al/PTFE)compositions including 2 PT(2.80 wt.%F),4 PT(7.18 wt.%F)and 8 PT(11.90 wt.%F)were studied.When the content of F increased from 2.80 wt.%to 11.90 wt.%,the minimum explosive concentration MEC decreased from380 g/m^(3)to 140 g/m^(3),due to the dual effects of increased internal active aluminum and enhanced reactivity.The average flame propagation velocities increased as the percentage of F increased.The maximum explosion pressure Pmof 500 g/m3aluminum-based activated fuels increased from 247 k Pa to299 kPa.Scanning electron microscopy demonstrated that with the increase of PTFE content,the reaction was more complete.On this basis,the explosion mechanism of aluminum-based activated fuels was revealed.展开更多
An infrared colorimetric radiation thermometrical system was established based on the theory of optical radiation. The dynamic temperature history of fuel air explosive (FAE) was measured to obtain the temperature res...An infrared colorimetric radiation thermometrical system was established based on the theory of optical radiation. The dynamic temperature history of fuel air explosive (FAE) was measured to obtain the temperature responses of primary initiation FAE and secondary initiation FAE in real time. And the characteristics of their temperature history curves were compared and analyzed. The results show that the primary initiation FAE has higher explosion temperature and longer duration compared to the secondary initiation FAE.展开更多
The combustion and explosion characteristics of lithium-ion battery vent gas is a key factor in determining the fire hazard of lithium-ion batteries.Investigating the combustion and explosion hazards of lithium-ion ba...The combustion and explosion characteristics of lithium-ion battery vent gas is a key factor in determining the fire hazard of lithium-ion batteries.Investigating the combustion and explosion hazards of lithium-ion batteries vent gas can provide guidance for rescue and protection in explosion accidents in energy storage stations and new energy vehicles,thereby promoting the application and development of lithium-ion batteries.Based on this understanding and combined with previous research on gas production from lithium-ion batteries,this article conducted a study on the combustion and explosion risks of vent gas from thermal runaway of 18650 LFP batteries with different states of charge(SOCs).The explosion limit of mixed gases affected by carbon dioxide inert gas is calculated through the“elimination”method,and the Chemkin-Pro software is used to numerically simulate the laminar flame speed and adiabatic flame temperature of the battery vent gas.And the concentration of free radicals and sensitivity coefficients of major elementary reactions in the system are analyzed to comprehensively evaluate the combustion explosion hazard of battery vent gas.The study found that the 100%SOC battery has the lowest explosion limit of the vent gas.The inhibitory elementary reaction sensitivity coefficient in the reaction system is lower and the concentration of free radicals is higher.Therefore,it has the maximum laminar flame speed and adiabatic flame temperature.The combustion and explosion hazard of battery vent gas increases with the increase of SOC,and the risk of explosion is the greatest and most harmful when SOC reaches 100%.However,the related hazards decrease to varying degrees with overcharging of the battery.This article provides a feasible method for analyzing the combustion mechanism of vent gas from lithium-ion batteries,revealing the impact of SOC on the hazardousness of battery vent gas.It provides references for the safety of storage and transportation of lithium-ion batteries,safety protection of energy storage stations,and the selection of related fire extinguishing agents.展开更多
Autoclaved aerated concrete(AAC) panels have ultra-light weight,excellent thermal insulation and energy absorption,so it is an ideal building material for protective structures.To improve the blast resistance of the A...Autoclaved aerated concrete(AAC) panels have ultra-light weight,excellent thermal insulation and energy absorption,so it is an ideal building material for protective structures.To improve the blast resistance of the AAC panels,three schemes are applied to strengthen the AAC panels through spraying 4 mm thick polyurea coating from top,bottom and double-sides.In three-point bending tests,the polyurea-coated AAC panels have much higher ultimate loads than the un-coated panels,but slightly lower than those strengthened by the carbon fiber reinforced plastics(CEFRPs).Close-in explosion experiments reveal the dynamic strengthening effect of the polyurea coating.Critical scaled distances of the strengthened AAC panels are acquired,which are valuable for the engineering application of the AAC panels in the extreme loading conditions.Polyurea coatings efficiently enhance the blast resistance of the bottom and double-sided polyurea-coated AAC panels.It is interesting that the polyurea-coated AAC panels have much more excellent blast resistance than the CFRP reinforced AAC panels,although the latter have better static mechanical properties.展开更多
Pressure histories were tested in a 500-L chamber to identify the pressure load in confined explosion from aluminized explosives. Different aluminized explosives with Al/O, ranging from 0.25 to 1.23, were used. The re...Pressure histories were tested in a 500-L chamber to identify the pressure load in confined explosion from aluminized explosives. Different aluminized explosives with Al/O, ranging from 0.25 to 1.23, were used. The recorded pressure curves could express the reflection of initial shock wave and the after burning combustion of aluminum. As there is no objective way to gain quasi-static pressure(P_(QS)),method of multipoint averaging was used in smoothing the original pressure curves to gain the P_(QS). The P_(QS),rising time of pressure(t_(QS)) which stands for the duration of the initial reflected shock wave, and attenuation coefficient(ω) which stands for the supportive effects of the combustion of aluminum to the P_(QS) are used to characterize the pressure load in the confined explosion from aluminized explosives. The research results showed that the Al/O significantly affected the three characteristic quantities. With the increase of Al/O, the P_(QS) increased at first and decreased later, gaining maximum at Al/O=0.99; the t_(QS)sustained growth and the ω decreased at first and increased later, gaining minimum at AI/O=0.99.展开更多
This paper presents the results of an experimental investigation on explosive breaching of p-section concrete beams. Twenty three p-section concrete beams with a 100 cm length were tested. TNT charges were placed at t...This paper presents the results of an experimental investigation on explosive breaching of p-section concrete beams. Twenty three p-section concrete beams with a 100 cm length were tested. TNT charges were placed at three positions: contact detonation in the center, contact detonation above the web and close-in detonation in the center. The external and internal breach parameters of the panels were evaluated by measuring the diameter of the ejection crater, spalling crater and breach hole created by the charge detonation. The experimental results were compared to predict values obtained by the analytical models proposed by McVay, Morishita and Remennikov. A modified breach with crater limit line and breach without crater limit line were put forward based on the experimental results. The maximum cross-sectional destruction area ratio(MCDAR) values were used to evaluate the damage degree. The maximum value of MCDAR reached 0.331 corresponding to the C5 experimental condition, of which explosion occurred above the web.展开更多
Blast vibration analysis is one of the important foundations for studying the control technology of blast vibration damage. According to blast vibration live data that have been collected and the characteristics of sh...Blast vibration analysis is one of the important foundations for studying the control technology of blast vibration damage. According to blast vibration live data that have been collected and the characteristics of short-time non-stationary random signals, the wavelet packet energy spectrum analysis for blast vibration signal has made by wavelet packet analysis technology and the signals were measured under different explosion parameters （the maximal section dose, the distance of blast source to measuring point and the section number of millisecond detonator）. The results show that more than 95% frequency band energy of the signals sl-s8 concentrates at 0-200 Hz and the main vibration frequency bands of the signals sl-s8 are 70.313-125, 46.875-93.75, 15.625-93.75, 0-62.5, 42.969-125, 15.625-82.031, 7.813-62.5 and 0-62.5 Hz. Energy distributions for different frequency bands of blast vibration signal are obtained and the characteristics of energy distributions for blast vibration signal measured under different explosion parameters are analyzed. From blast vibration signal energy, the decreasing law of blast seismic waves measured under different explosion parameters was studied and the wavelet packet analysis is an effective means for studying seismic effect induced by blast.展开更多
基金the financial support of the Shanxi Fire & Explosion-Proofing Safety Engineering and Technology Research Center, North University of China。
文摘Due to the presence of nitro groups, the dust generated during the production and utilization of energetic materials may potentially lead to dust explosion even under low-oxygen or anaerobic conditions.Considering the high energy density of energetic materials, dust explosion can cause serious production safety accidents. Therefore, it is necessary to understand the dust explosion characteristics of energetic materials and the mechanism of dust explosion. According to the literature review, among various influencing factors, the physical and chemical properties of dust are the decisive factors affecting the explosion characteristics of dust. In addition to experimental studies, numerical simulation is another important tool. However, it is subjected to certain limitations. Moreover, it is essential but challenging to fully understand the underlying mechanism. In addition, given the safety hazards posed by dust explosion, explosion suppression has attracted extensive attention for research. Depending on the medium used, there are different forms of suppression, including powder explosion suppression, water spray explosion suppression, inert gas explosion suppression, porous material explosion suppression, and vacuum chamber explosion suppression. As for the selection of explosion suppression agent, consideration must be given to the characteristics of the material. Furthermore, the above research has laid a foundation for discussing the future progress in studying dust explosion of energetic materials, with nano dust and the constraints of existing technology as the focal point.
基金the financial support of the Shanxi Fire&Explosion-Proofing Safety Engineering and Technology Research Center,North University of China。
文摘RDX/Al mixtures are widely utilized in energetic materials,yet their hybrid dust generated during production and application poses potential explosion hazards.Moreover,the synergistic explosion mechanisms remain poorly understood,particularly at varying dust concentrations.This study systematically investigates the effects of different aluminum powder mass percentages and dust concentrations(300 g/m^(3),600 g/m^(3),900 g/m^(3))on RDX dust explosion severity,flame propagation behavior,and gaseous products.The results indicate that the maximum explosion pressure peaks at 35%RDX,65%RDX,and 80%RDX at 300 g/m^(3),600 g/m^(3),and 900 g/m^(3),respectively.Concurrently,the time for the flame to propagate to the wall(t1)reaches minimum values of 34.8 ms,25.66 ms,and 23.93 ms.The maximum rate of pressure rise is observed for pure RDX at 900 g/m^(3).Aluminum powder enhances flame propagation velocity and combustion duration,as validated by the flame propagation system.Overall,the concentrations of carbon oxides(CO+CO_(2))decrease significantly with increasing aluminum mass percentage.At 20%RDX,the concentrations decreased by 51.64%,72.31%,and 79.55%compared to pure RDX at 300 g/m^(3),600 g/m^(3),and 900 g/m^(3),respectively.Notably,N_(2)O concentration only at 300 g/m^(3)showed such a trend.It rises first and then falls at 35%RDX at 600 g/m^(3)and 900 g/m^(3).These findings elucidate the synergistic explosion mechanisms and provide critical guidelines for safe production and handling.
基金supported by the National Natural Science Foundation of China(Grant No.52274177)Science and Technology Research Program of Chongqing Municipal Education Commission(Grant No.KJZD-K202401501)+1 种基金Chongqing Graduate Student Research Innovation Program(Grant No.CYS240800)The Science and Technology Innovation Project for Graduate Students of Chongqing University of Science and Technology(Grant No.YKJCX2420702).
文摘Urban growth has promoted the use of underground spaces,where explosion accidents can be catastrophic.In this study,we investigated the effect of placing flexible construction in front of rigid obstacles on methane explosion protection by using an experimental platform and adjusting the blockage rate and spacing of the obstacles.It aims to reduce the risk of gas explosions in urban underground spaces.The results of the study show that the flame propagation peak speed and peak overpressure are reduced with the decrease in the blocking rate of the flexible obstacle when the blocking rate of the flexible obstacle is less than or equal to the blocking rate of the rigid obstacle,with the decrease in the spacing,the better the protection effect of the methane explosion.When the blockage rate of the flexible obstacle is greater than the blockage rate of the rigid obstacle and spacing is less than the height of the flexible obstacle,rigid and flexible obstacles are connected as a whole,increasing the strength of the explosion.This study can provide a theoretical basis and scientific guidance for optimizing rigid and flexible object hybrid layouts and methane explosion protection technology in urban underground spaces.
基金financial support from National Natural Science Foundation of China(Grant No.52378488)Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYCX22_0222).
文摘Gas explosion in confined space often leads to significant pressure oscillation.It is widely recognized that structural damage can be severe when the oscillation frequency of the load resonates with the natural vibration frequency of the structure.To reveal the oscillation mechanism of gas explosion load,the experiment of gas explosion was conducted in a large-scale confined tube with the length of 30 m,and the explosion process was numerically analyzed using FLACS.The results show that the essential cause of oscillation effect is the reflection of the pressure wave.In addition,due to the difference in the propagation path of the pressure wave,the load oscillation frequency at the middle position of the tunnel is twice that at the end position.The average sound velocity can be used to calculate the oscillation frequency of overpressure accurately,and the error is less than 15%.The instability of the flame surface and the increase of flame turbulence caused by the interaction between the pressure wave and the flame surface are the main contributors to the increase in overpressure and amplitude.The overpressure peaks calculated by the existing flame instability model and turbulence disturbance model are 31.7%and 34.7%lower than the numerical results,respectively.The turbulence factor model established in this work can describe the turbulence enhancement effect caused by flame instability and oscillatory load,and the difference between the theoretical and numerical results is only 4.6%.In the theoretical derivation of the overpressure model,an improved model of dynamic turbulence factor is established,which can describe the enhancement effect of turbulence factor caused by flame instability and self-turbulence.Based on the one-dimensional propagation theory of pressure wave,the oscillatory effect of the load is derived to calculate the frequency and amplitude of pressure oscillation.The average error of amplitude and frequency is less than 20%.
基金the financial support from National Natural Science Foundation of China(Grant No.52378488)Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYCX22_0222)。
文摘The gas explosion in residential building has always been a highly concerned problem.Explosions in homogeneous mixtures have been extensively studied.However,mixtures are often inhomogeneous in the practical scenarios due to the differences in the densities of methane and air.In order to investigate the effects of gas explosions in inhomogeneous mixtures,experimental studies involving gas leakage and explosion are conducted in a full-scale residential building to reproduce the process of gas explosion.By fitting the dimensionless buoyancy as a function of dimensionless height and dimensionless time,a distribution model of gas in large-scale spaces is established,and the mechanism of inhomogeneous distribution of methane is also be revealed.Furthermore,the stratified reconstruction method(SRM)is introduced for efficiently setting up inhomogeneous concentration fields in FLACS.The simulation results highlight that for the internal overpressure,the distribution of methane has no effect on the first overpressure peak(ΔP1),while it significantly influences the subsequent overpressure peak(ΔP2),and the maximum difference between the overpressure of homogeneous and inhomogeneous distribution is174.3%.Moreover,the initial concentration distribution also has a certain impact on the external overpressure.
基金supported by the Young Scientists Fund of National Natural Science Foundation of China(Grant Nos.12202202 and 12202494)the National Key Research and Development Program of China(Grant No.2021YFC3100700)。
文摘The internal and external flow fields during vented explosions of methane were characterized through numerical simulation,and the capability of numerical simulation thereof was validated by previous experimental data at three ignition positions.The venting mechanism was revealed by the simulated concentration distribution,temperature profile,and airflow velocity.The results show rear ignition results in the external methane mass distribution taking the form of"mushroom"and columnar flames in the external space,which can be expressed as a third-order polynomial relationship with distance;central ignition forms a relationship of the form y=AxB.Front ignition causes the temperature to show a tendency to repeated oscillations(rising,falling,and rising).Central ignition generates the maximum vented airflow velocity(V_(max)=320 m/s)upon vent opening.The results indicate that it is acceptable to apply numerical simulation of methane explosions in practice.
基金financially supported by the National Natural Science Foundation of China (Grant No. 52278504)the Natural Science Foundation of Jiangsu Province (Grant No. BK20220141)。
文摘The afterburning of TNT and structural constraints in confined spaces significantly amplify the blast load,leading to severe structural damage. This study investigates the mechanisms underlying the enhanced dynamic response of reinforced concrete blast doors with four-sided restraints in confined space. Explosion tests with TNT charges ranging from 0.15 kg to 0.4 kg were conducted in a confined space,capturing overpressure loads and the dynamic response of the blast door. An internal explosion model incorporating the afterburning effect was developed using LS-DYNA software and validated against experimental data. The results reveal that the TNT afterburning effect amplifies both the initial peak overpressure and the quasi-static overpressure, resulting in increased deformation of the blast door.Within the 0.15-0.4 kg charge range, the initial overpressure peak and quasi-static overpressure increased by an average of 1.79 times and 2.21 times, respectively. Additionally, the afterburning effect enhanced the blast door's deflection by 177%. Compared to open-space scenarios, the cumulative deflection of the blast door due to repeated shock wave impacts is significantly greater in confined spaces. Furthermore, the quasi-static pressure arising from the structural constraints sustains the blast door's deflection at a high level.
基金the support provided by the Technology Innovation Project (Grant No. KYGYZB002201) for the research work
文摘Investigating the blast effects and mechanisms on typical finite-sized obstacles is essential for optimizing defense strategies and designing more robust barriers to deter terrorists and protect critical locations.This study investigates the blasting effects and underlying mechanisms of concrete frustums subjected to contact explosions,employing both numerical simulations and field tests.It focuses on the effects of top and side blasting,with particular emphasis on fracture modes,damage patterns,and fragment sizes,as well as the causes of different failure modes and the propagation of stress waves.The study also explores the blasting effects of detonating explosives at varying positions along the side and with different charge amounts.The results show that side-blasting leads to complete fragmentation,with tensile waves playing a significant role in creating extensive damage zones that propagate parallel to the frustum's outer surface,concentrating damage near the surface.During top-blasting,the upper half of the frustum undergoes fragmentation,while the lower half experiences cracking.Tensile waves propagate from the top to the bottom surface,forming larger blocks in regions with lower wave intensity.Three distinct damage zones within the frustum were identified,and a series of mathematical formulas were derived to describe the relationship between the maximum fragment size and charge mass.As the charge mass increased from 1.0 kg to 4.0 kg,the maximum fragment size decreased.Detonation at the center of the frustum's side resulted in the most severe fragmentation,with a 51.8%reduction in fragment size compared to other detonation positions.Finally,four broken modes were classified,each influenced by charge mass and explosive location.This study provides valuable insights for optimizing civil blasting operations and designing protective engineering structures.
基金supported by the National Natural Science Foundation of China(grant numbers:52201334)sup-ported by National Key Laboratory of Ship Structural Safety(grant numbers:Naklas2024-KF015-s).
文摘To investigate the explosion load characteristics and structural response law in a water mist environment in a cabin,explosion experiments are carried out.The weakening rates of the initial peak overpressure,quasistatic pressure and structural residual deflection increase with increasing working pressure of the water mist nozzle.Specifically,the weakening rate of the initial peak overpressure ranges from 7.8%to 31.0%,the quasistatic pressure weakening rate ranges from 29.2%to 41.0%,and the weakening rate of the center of the plate residual deflection ranges from 10.8%to 34.4%under the various working pressures of the nozzles.To further explore the effect of water mist explosion suppression,a method for three-dimensional numerical simulations of water mist weakening the explosion shock wave is established to explore the explosion load characteristics of the compartment and the bulkhead response law.On the basis of the dimension analysis method,empirical formulas are derived to predict the residual deflection thickness in the center of the bulkheads.These findings provide the fundamental basis for the appli-cation of water mist in anti-explosive protection.
基金supported by the National Natural Science Foundation of China(Grant Nos.12302435 and 12221002)。
文摘Shock wave caused by a sudden release of high-energy,such as explosion and blast,usually affects a significant range of areas.The utilization of a uniform fine mesh to capture sharp shock wave and to obtain precise results is inefficient in terms of computational resource.This is particularly evident when large-scale fluid field simulations are conducted with significant differences in computational domain size.In this work,a variable-domain-size adaptive mesh enlargement(vAME)method is developed based on the proposed adaptive mesh enlargement(AME)method for modeling multi-explosives explosion problems.The vAME method reduces the division of numerous empty areas or unnecessary computational domains by adaptively suspending enlargement operation in one or two directions,rather than in all directions as in AME method.A series of numerical tests via AME and vAME with varying nonintegral enlargement ratios and different mesh numbers are simulated to verify the efficiency and order of accuracy.An estimate of speedup ratio is analyzed for further efficiency comparison.Several large-scale near-ground explosion experiments with single/multiple explosives are performed to analyze the shock wave superposition formed by the incident wave,reflected wave,and Mach wave.Additionally,the vAME method is employed to validate the accuracy,as well as to investigate the performance of the fluid field and shock wave propagation,considering explosive quantities ranging from 1 to 5 while maintaining a constant total mass.The results show a satisfactory correlation between the overpressure versus time curves for experiments and numerical simulations.The vAME method yields a competitive efficiency,increasing the computational speed to 3.0 and approximately 120,000 times in comparison to AME and the fully fine mesh method,respectively.It indicates that the vAME method reduces the computational cost with minimal impact on the results for such large-scale high-energy release problems with significant differences in computational domain size.
文摘In this study, we focused on the effect of the underwater explosion parameters of multi-point array explosion. The shock wave and bubble parameters of aggregate charge, two charges, and four charges were measured through an underwater explosion test, and their influence on the explosion power field of charge quantity and array distance was analyzed. Results show that the multi-shock wave collision of array explosion can be approximated to a linear superposition, and the interaction of delayed shock wave can be deemed as the increase of the shock wave baseline. Shock wave focusing and delayed superposition increase the shock wave peak pressure. Compared with the aggregate charge, the greater the number of array explosion points is, the higher the impulse and the gain of the bubble peak pressure are. At the same array distance, the smaller the charge quantity is, the higher the bubble impulse will be. At the same charge quantity, the smaller the array distance is, the higher the bubble impulse will be. The bubble period decreases gradually with the increase of the charge quantity, but the test orientation has little effect on the bubble period.
基金supported by the National Natural Science Foundation of China(Grant Nos.12002156,11972185,12372136)Research Fund of State Key Laboratory of Mechanics and Control for Aerospace Structures(Grant No.MCMS-I-0222K01)。
文摘While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and numerical study has been carried out to characterize the effect of SCW on transferred impulse and loading magnitude of shallow buried explosives.Firstly,blast tests of shallow buried explosives were conducted,with and without the SCW,to quantitatively assess the blast loading impulse.Subsequently,finite element(FE)simulations were performed and validated against experimental measurement,with good agreement achieved.The validated FE model was then employed to predict the dynamic response of a fully-clamped metallic circular target,subjected to the explosive impact of shallow buried explosives with SCW,and explore the corresponding physical mechanisms.It was demonstrated that shallow buried explosives in saturated soil generate a greater impulse transferred towards the target relative to those in dry soil.The deformation displacement of the target plate is doubled.Increasing the height of SCW results in enhanced center peak deflection of the loaded target,accompanied by subsequent fall,due to the variation of deformation pattern of the loaded target from concentrated load to uniform load.Meanwhile,the presence of SCW increases the blast impulse transferred towards the target by three times.In addition,there exists a threshold value of the burial depth that maximizes the impact impulse.This threshold exhibits a strong sensitivity to SCW height,decreasing with increasing SCW height.An empirical formula for predicting threshold has been provided.Similar conclusions can be drawn for different explosive masses.The results provide technical guidance on blast loading intensity and its spatial distribution considering shallow buried explosives in coast-land battlefields,which can ultimately contribute to better protective designs.
基金supported by the National Natural Science Foundation of China(No.11972046)Outstanding Youth Project of Natural Science Foundation of Anhui Province(No.2108085Y02)+1 种基金Major Project of Anhui University Natural Science Foundation(No.KJ2020ZD30)Anhui University of Science and Technology Postgraduate Innovation Fund(No.2020CX2066)。
文摘In the study,the two-color pyrometer technique was used to measure the transient temperature field of emulsion explosives with different contents of TiH_(2)powders.The experimental results showed that the introduction of TiH_(2)powders could significantly increase the explosion temperature and fireball duration of emulsion explosive.When emulsion explosives were ignited,the average explosion temperature of pure emulsion explosive continuously decreased while emulsion explosives added with TiH_(2)powders increased at first and then decreased.When the content of TiH_(2)powders was 6 mass%,the explosion average temperature reached its maximum value of 3095 K,increasing by 43.7%as compared with that of pure emulsion explosive.In addition,the results of air blast experiment and explosion heat test showed that the variation trends of shock wave parameters,explosion heat and theoretical explosion temperature of emulsion explosives with different contents of TiH_(2)powders were basically consistent with that of explosion temperature measured by the two-color pyrometer technique.In conclusion,the two-color pyrometer technique would be conducive to the formula design of emulsion explosive by understanding the explosion temperature characteristics.
基金financially supported by National Natural Science Foundation of China(No.51922025 and No.51874066)China Postdoctoral Science Foundation(No.2020M670759)the Fundamental Research Funds for the Central Universities(No.DUT20GJ201)。
文摘Measuring the dust explosion characteristics of aluminum-based activated fuels was a prerequisite for developing effective prevention and control measures.In this paper,ignition sensitivity,flame propagation behaviors and explosion severity of aluminum/polytetrafluoroethylene(Al/PTFE)compositions including 2 PT(2.80 wt.%F),4 PT(7.18 wt.%F)and 8 PT(11.90 wt.%F)were studied.When the content of F increased from 2.80 wt.%to 11.90 wt.%,the minimum explosive concentration MEC decreased from380 g/m^(3)to 140 g/m^(3),due to the dual effects of increased internal active aluminum and enhanced reactivity.The average flame propagation velocities increased as the percentage of F increased.The maximum explosion pressure Pmof 500 g/m3aluminum-based activated fuels increased from 247 k Pa to299 kPa.Scanning electron microscopy demonstrated that with the increase of PTFE content,the reaction was more complete.On this basis,the explosion mechanism of aluminum-based activated fuels was revealed.
基金Sponsored by the National Natural Science Foundation of China (10772032)
文摘An infrared colorimetric radiation thermometrical system was established based on the theory of optical radiation. The dynamic temperature history of fuel air explosive (FAE) was measured to obtain the temperature responses of primary initiation FAE and secondary initiation FAE in real time. And the characteristics of their temperature history curves were compared and analyzed. The results show that the primary initiation FAE has higher explosion temperature and longer duration compared to the secondary initiation FAE.
基金supported by the National Natural Science Foundation of China(52106284)the Natural Science Foundation of Hebei Province(B2021507001)support of Project to Promote Innovation in Doctoral Research at CPPU(BSKY202302).
文摘The combustion and explosion characteristics of lithium-ion battery vent gas is a key factor in determining the fire hazard of lithium-ion batteries.Investigating the combustion and explosion hazards of lithium-ion batteries vent gas can provide guidance for rescue and protection in explosion accidents in energy storage stations and new energy vehicles,thereby promoting the application and development of lithium-ion batteries.Based on this understanding and combined with previous research on gas production from lithium-ion batteries,this article conducted a study on the combustion and explosion risks of vent gas from thermal runaway of 18650 LFP batteries with different states of charge(SOCs).The explosion limit of mixed gases affected by carbon dioxide inert gas is calculated through the“elimination”method,and the Chemkin-Pro software is used to numerically simulate the laminar flame speed and adiabatic flame temperature of the battery vent gas.And the concentration of free radicals and sensitivity coefficients of major elementary reactions in the system are analyzed to comprehensively evaluate the combustion explosion hazard of battery vent gas.The study found that the 100%SOC battery has the lowest explosion limit of the vent gas.The inhibitory elementary reaction sensitivity coefficient in the reaction system is lower and the concentration of free radicals is higher.Therefore,it has the maximum laminar flame speed and adiabatic flame temperature.The combustion and explosion hazard of battery vent gas increases with the increase of SOC,and the risk of explosion is the greatest and most harmful when SOC reaches 100%.However,the related hazards decrease to varying degrees with overcharging of the battery.This article provides a feasible method for analyzing the combustion mechanism of vent gas from lithium-ion batteries,revealing the impact of SOC on the hazardousness of battery vent gas.It provides references for the safety of storage and transportation of lithium-ion batteries,safety protection of energy storage stations,and the selection of related fire extinguishing agents.
基金Supports from the National Natural Science Foundation of China(11672130,51508567,51478465,and 51308544)the State Key Laboratory of Mechanics and Control of Mechanical Structures(MCMS-0217G03)the State Key Laboratory for Disaster Reduction in Civil Engineering(SLDRCE16-01)。
文摘Autoclaved aerated concrete(AAC) panels have ultra-light weight,excellent thermal insulation and energy absorption,so it is an ideal building material for protective structures.To improve the blast resistance of the AAC panels,three schemes are applied to strengthen the AAC panels through spraying 4 mm thick polyurea coating from top,bottom and double-sides.In three-point bending tests,the polyurea-coated AAC panels have much higher ultimate loads than the un-coated panels,but slightly lower than those strengthened by the carbon fiber reinforced plastics(CEFRPs).Close-in explosion experiments reveal the dynamic strengthening effect of the polyurea coating.Critical scaled distances of the strengthened AAC panels are acquired,which are valuable for the engineering application of the AAC panels in the extreme loading conditions.Polyurea coatings efficiently enhance the blast resistance of the bottom and double-sided polyurea-coated AAC panels.It is interesting that the polyurea-coated AAC panels have much more excellent blast resistance than the CFRP reinforced AAC panels,although the latter have better static mechanical properties.
文摘Pressure histories were tested in a 500-L chamber to identify the pressure load in confined explosion from aluminized explosives. Different aluminized explosives with Al/O, ranging from 0.25 to 1.23, were used. The recorded pressure curves could express the reflection of initial shock wave and the after burning combustion of aluminum. As there is no objective way to gain quasi-static pressure(P_(QS)),method of multipoint averaging was used in smoothing the original pressure curves to gain the P_(QS). The P_(QS),rising time of pressure(t_(QS)) which stands for the duration of the initial reflected shock wave, and attenuation coefficient(ω) which stands for the supportive effects of the combustion of aluminum to the P_(QS) are used to characterize the pressure load in the confined explosion from aluminized explosives. The research results showed that the Al/O significantly affected the three characteristic quantities. With the increase of Al/O, the P_(QS) increased at first and decreased later, gaining maximum at Al/O=0.99; the t_(QS)sustained growth and the ω decreased at first and increased later, gaining minimum at AI/O=0.99.
基金supported by The National Natural Science Foundation of China under Grant No.11390362 and No. 11221202
文摘This paper presents the results of an experimental investigation on explosive breaching of p-section concrete beams. Twenty three p-section concrete beams with a 100 cm length were tested. TNT charges were placed at three positions: contact detonation in the center, contact detonation above the web and close-in detonation in the center. The external and internal breach parameters of the panels were evaluated by measuring the diameter of the ejection crater, spalling crater and breach hole created by the charge detonation. The experimental results were compared to predict values obtained by the analytical models proposed by McVay, Morishita and Remennikov. A modified breach with crater limit line and breach without crater limit line were put forward based on the experimental results. The maximum cross-sectional destruction area ratio(MCDAR) values were used to evaluate the damage degree. The maximum value of MCDAR reached 0.331 corresponding to the C5 experimental condition, of which explosion occurred above the web.
基金Foundation item: Project(51064009) supported by the National Natural Science Foundation of ChinaProject(201104356) supported by the China Postdoctoral Science FoundationProject(20114BAB206030) supported by the Natural Science Foundation of Jiangxi Province,China
文摘Blast vibration analysis is one of the important foundations for studying the control technology of blast vibration damage. According to blast vibration live data that have been collected and the characteristics of short-time non-stationary random signals, the wavelet packet energy spectrum analysis for blast vibration signal has made by wavelet packet analysis technology and the signals were measured under different explosion parameters （the maximal section dose, the distance of blast source to measuring point and the section number of millisecond detonator）. The results show that more than 95% frequency band energy of the signals sl-s8 concentrates at 0-200 Hz and the main vibration frequency bands of the signals sl-s8 are 70.313-125, 46.875-93.75, 15.625-93.75, 0-62.5, 42.969-125, 15.625-82.031, 7.813-62.5 and 0-62.5 Hz. Energy distributions for different frequency bands of blast vibration signal are obtained and the characteristics of energy distributions for blast vibration signal measured under different explosion parameters are analyzed. From blast vibration signal energy, the decreasing law of blast seismic waves measured under different explosion parameters was studied and the wavelet packet analysis is an effective means for studying seismic effect induced by blast.
