Aqueous zinc metal batteries(ZMBs)which are environmentally benign and cheap can be used for grid-scale energy storage,but have a short cycling life mainly due to the poor reversibility of zinc metal anodes in mild aq...Aqueous zinc metal batteries(ZMBs)which are environmentally benign and cheap can be used for grid-scale energy storage,but have a short cycling life mainly due to the poor reversibility of zinc metal anodes in mild aqueous electrolytes.A zincophilic carbon(ZC)layer was deposited on a Zn metal foil at 450°C by the up-stream pyrolysis of a hydrogen-bonded supramolecular substance framework,as-sembled from melamine(ME)and cyanuric acid(CA).The zincophilic groups(C=O and C=N)in the ZC layer guide uniform zinc plating/stripping and eliminate dendrites and side reactions.so that assembled symmetrical batteries(ZC@Zn//ZC@Zn)have a long-term service life of 2500 h at 1 mA cm^(−2) and 1 mAh cm^(−2),which is much longer than that of bare Zn anodes(180 h).In addition,ZC@Zn//V2O5 full batteries have a higher capacity of 174 mAh g^(−1) after 1200 cycles at 2 A g^(−1) than a Zn//V_(2)O_(5) counterpart(100 mAh g^(−1)).The strategy developed for the low-temperat-ure deposition of the ZC layer is a new way to construct advanced zinc metal anodes for ZMBs.展开更多
A process was proposed to convert and separate selenium and arsenic in copper anode slime(CAS) by low-temperature alkali fusion process.Central composite design was employed to optimize the effective parameters,in whi...A process was proposed to convert and separate selenium and arsenic in copper anode slime(CAS) by low-temperature alkali fusion process.Central composite design was employed to optimize the effective parameters,in which Na OH/CAS mass ratio,fusion temperature and fusion time were selected as variables,and the conversion ratio of selenium and arsenic as responses.Second-order polynomial models of high significance and 3D response surface plots were constructed to show the relationship between the responses and the variables.Optimum area of >90% selenium conversion ratio and >90% arsenic conversion ratio was obtained by the overlaid contours at Na OH/CAS mass ratio of 0.65-0.75,fusion temperature of 803-823 K and fusion time of 20-30 min.The models are validated by experiments in the optimum area,and the results demonstrate that these models are reliable and accurate in predicting the fusion process.展开更多
Asphalt mixture pavement reheating is one of the important steps in hot in-place recycling(HIR).To improve the heating speed of asphalt pavement in HIR,based on the numerical analysis model of asphalt mixture heating ...Asphalt mixture pavement reheating is one of the important steps in hot in-place recycling(HIR).To improve the heating speed of asphalt pavement in HIR,based on the numerical analysis model of asphalt mixture heating process,a new multi-layer low-temperature heating method(MLHM)was proposed.Considering input heat flux,the thermal capacity and thermal resistance of asphalt mixture,the heat transfer model was established based on energy conservation law.By heating the asphalt mixture in layers,it changes the situation that the heat energy can only be input from the upper surface of the asphalt mixture pavement.Through the simulation of the heating method of asphalt mixture in the existing technology,the result shows that the existing heating methods lead to serious aging or charring of the asphalt mixture.By MLHM,the upper and the bottom of the asphalt mixture are heated at the same time,and the heating temperature is lower than other heat methods,which not only reduces the heating thickness and increases the heating area of the asphalt mixture pavement,but also improves the heating speed,saves the energy resource and ensures the heating quality.Especially,by MLHM,the heating uniformity is better and speed is faster.展开更多
Three varieties were employed as materials to study changes of photosynthetic traits under low-temperature stress. The results showed that Pn, Gs and Tr decreased under low-temperature treatment. Ci decreased under lo...Three varieties were employed as materials to study changes of photosynthetic traits under low-temperature stress. The results showed that Pn, Gs and Tr decreased under low-temperature treatment. Ci decreased under low-temperature treatment 18℃/ 9℃, and 16℃/7℃, and it decreased in earlier stage after increased under 14℃/5℃. WUE was increased in earlier stage and after stabilized. The order of the three varieties of cold resistance were Jinyu 5〉Xingken 3〉Jidan 198. They could make self-regulation through adjusting Gs, Tr, Ci and WUE.展开更多
The influences of BaCu（B2O5） （BCB） addition on sintering, microstructure and microwave dielectric properties of Li2MgTi308 ceramics were investigated using X-ray diffractometry, scanning electron microscopy and mi...The influences of BaCu（B2O5） （BCB） addition on sintering, microstructure and microwave dielectric properties of Li2MgTi308 ceramics were investigated using X-ray diffractometry, scanning electron microscopy and microwave dielectric measurements. The experimental results show that a small amount of BaCu（B2O5） addition can effectively reduce the sintering temperature to 900℃, and induce only a limited degradation of the microwave dielectric properties. Typically, the best microwave dielectric properties of er24.5, Q×f =24 622 GHz, rf=4.2×10-6℃ -1 are obtained for 1.0% BCB-doped Li2MgTi3O8 ceramics sintered at 900℃ for 3 h. The BCB-doped Li2MgTi3O8 ceramics can be compatible with Ag electrode, which may be a strong candidate for low temperature co-fired ceramics applications.展开更多
A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used t...A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.展开更多
Considering that Fe,Al elements in bauxite residue are active components for water purification,an effective polyaluminum ferric chloride(PAFC)coagulant derived from bauxite residue,with Fe2O3 content>5.1%,Al2O3%&g...Considering that Fe,Al elements in bauxite residue are active components for water purification,an effective polyaluminum ferric chloride(PAFC)coagulant derived from bauxite residue,with Fe2O3 content>5.1%,Al2O3%>6.5%,basicity>65%,was successfully prepared.The effect of as-prepared PAFC on the zeta potential for printing and dyeing wastewater was investigated.Comparing with polyferric chloride(PFC)and polyferric sulfate(PFS)for printing and dyeing wastewater treatment,prepared bauxite residue-based PAFC exhibited the optimal performance in the aspects of chromaticity and chemical oxygen demand(COD)removal rate.Furthermore,the combination of bauxite residue-based PAFC and PFS for synergy coagulation of such wastewater demonstrated an obvious positive effect.With the proportion between as-prepared PAFC and PFS to be 2.5:1,the COD of treated wastewater could be further reduced to meet the national level A standard of China,providing a promising route to solve the problem of substandard printing and dyeing sewage outfall by a simple coagulation strategy.展开更多
The hot compression test of 6063 Al alloy was performed on a Gleeble-1500 thermo-simulation machine, and the forming of 6063 rod cxtrudate in low-temperature high-speed extrusion was simulated with extrusion ratio of ...The hot compression test of 6063 Al alloy was performed on a Gleeble-1500 thermo-simulation machine, and the forming of 6063 rod cxtrudate in low-temperature high-speed extrusion was simulated with extrusion ratio of 25 on the platform of DEFORM 2D successfully. From the compression experimental results, the flow stress model of this Al alloy is obtained which could be the constitutive equation in the simulation of low-temperature high-speed extrusion process. From the numerical simulation results, there is a higher strain concentration at the entrance of the die and the exit temperature reaches up to 522 ℃ in low-temperature high-speed extrusion, which approaches to the quenching temperature of the 6063 Al alloy. The results show that the low-temperature high-speed extrusion method as a promsing one can reduce energy consumption effectively.展开更多
Studies on the cold-responsive genes and cold signaling of woody species drop far behind in comparison to herbaceous plants.Due to similar lignified structure,perennial characteristic,and enhanced tolerance,it seems m...Studies on the cold-responsive genes and cold signaling of woody species drop far behind in comparison to herbaceous plants.Due to similar lignified structure,perennial characteristic,and enhanced tolerance,it seems much easier to find strongly antifreeze genes and obtain effective results in transgenic woody plants.In this study,Ammopiptanthus mongolicus,an evergreen,broadleaf and cold-resist leguminous shrub growing in the desert of Inner Mongolia,was used as a material for low-temperature induced gene isolation.Through differential expression analysis induced by low-temperature,thirteen up-regulated cDNAs were identified.One of them,AmEBP1,(accession number:DQ519359)confers enhanced cold-tolerance to both transgenic E.coli and transgenic Arabidopsis.Results suggest that AmEBP1 can stimulate the synthesis of ribosome and the dephosphyration of the α-subunit of initiation factor 2(eIF2α),and subsequently promote the translation process.By which the transgenic plants obtained increased cold-resistant ability.展开更多
1IntroductionThe dyeing and finishing process is animportant step in textile processing,which makes great contribution to theadded-value of textile and garment.The Chinese government and the textilecircles attach grea...1IntroductionThe dyeing and finishing process is animportant step in textile processing,which makes great contribution to theadded-value of textile and garment.The Chinese government and the textilecircles attach great importance to thedevelopment of the dyeing and finishingindustry.It has been listed as one of in-dustries that will get major support fromthe state In the last few years,sincethe government has given it展开更多
Coacervation of oxidized glutathione(GSSG)and a cationic surfactant,didodecyldimethylammonium bromide(DDAB),was constructed mainly driven by the electrostatic and hydrophobic interactions.The pH-dependent coacervate o...Coacervation of oxidized glutathione(GSSG)and a cationic surfactant,didodecyldimethylammonium bromide(DDAB),was constructed mainly driven by the electrostatic and hydrophobic interactions.The pH-dependent coacervate of GSSG-DDAB(1∶4,mol/mol)was analyzed.Under acidic and neutral conditions,a turbid suspension of droplets is observed,and alkaline pH results in the phase separation of coacervates as the top phase.The coacervate phase exhibits good performance(extraction efficiency>85%)in extracting several dyes from water,including brilliant yellow,acid red 13,cresyl violet acetate,eriochrom blue SE,and 4-hydroxyazobenzene.The dyes are added into the suspension in acidic conditions.Then,the dyes are enriched and extracted along with the coacervates as the top phase when pH is adjusted to~10.Coacervation of GSSG with DDAB provides a simple approach to extract organic pollutants in wastewater treatment.展开更多
基金partially supported by the National Natural Science Foundation of China(22479022)Liaoning Revitalization Talents Program(XLYC2007129)。
文摘Aqueous zinc metal batteries(ZMBs)which are environmentally benign and cheap can be used for grid-scale energy storage,but have a short cycling life mainly due to the poor reversibility of zinc metal anodes in mild aqueous electrolytes.A zincophilic carbon(ZC)layer was deposited on a Zn metal foil at 450°C by the up-stream pyrolysis of a hydrogen-bonded supramolecular substance framework,as-sembled from melamine(ME)and cyanuric acid(CA).The zincophilic groups(C=O and C=N)in the ZC layer guide uniform zinc plating/stripping and eliminate dendrites and side reactions.so that assembled symmetrical batteries(ZC@Zn//ZC@Zn)have a long-term service life of 2500 h at 1 mA cm^(−2) and 1 mAh cm^(−2),which is much longer than that of bare Zn anodes(180 h).In addition,ZC@Zn//V2O5 full batteries have a higher capacity of 174 mAh g^(−1) after 1200 cycles at 2 A g^(−1) than a Zn//V_(2)O_(5) counterpart(100 mAh g^(−1)).The strategy developed for the low-temperat-ure deposition of the ZC layer is a new way to construct advanced zinc metal anodes for ZMBs.
基金Project(51234009)supported by the National Natural Science Foundation of ChinaProject(2014DFA90520)supported by International Cooperation Program of Ministry of Science of ChinaProject(2013A100003)supported by the Production,Teaching and Research Program of Guangdong Province,China
文摘A process was proposed to convert and separate selenium and arsenic in copper anode slime(CAS) by low-temperature alkali fusion process.Central composite design was employed to optimize the effective parameters,in which Na OH/CAS mass ratio,fusion temperature and fusion time were selected as variables,and the conversion ratio of selenium and arsenic as responses.Second-order polynomial models of high significance and 3D response surface plots were constructed to show the relationship between the responses and the variables.Optimum area of >90% selenium conversion ratio and >90% arsenic conversion ratio was obtained by the overlaid contours at Na OH/CAS mass ratio of 0.65-0.75,fusion temperature of 803-823 K and fusion time of 20-30 min.The models are validated by experiments in the optimum area,and the results demonstrate that these models are reliable and accurate in predicting the fusion process.
基金Project(2017JM5077)supported by the Natural Science Basic Research Plan in Shaanxi Province,ChinaProjects(300102259109,300102259306)supported by the Fundamental Research Funds for the Central Universities,China。
文摘Asphalt mixture pavement reheating is one of the important steps in hot in-place recycling(HIR).To improve the heating speed of asphalt pavement in HIR,based on the numerical analysis model of asphalt mixture heating process,a new multi-layer low-temperature heating method(MLHM)was proposed.Considering input heat flux,the thermal capacity and thermal resistance of asphalt mixture,the heat transfer model was established based on energy conservation law.By heating the asphalt mixture in layers,it changes the situation that the heat energy can only be input from the upper surface of the asphalt mixture pavement.Through the simulation of the heating method of asphalt mixture in the existing technology,the result shows that the existing heating methods lead to serious aging or charring of the asphalt mixture.By MLHM,the upper and the bottom of the asphalt mixture are heated at the same time,and the heating temperature is lower than other heat methods,which not only reduces the heating thickness and increases the heating area of the asphalt mixture pavement,but also improves the heating speed,saves the energy resource and ensures the heating quality.Especially,by MLHM,the heating uniformity is better and speed is faster.
基金Supported by the Science and Technology Foundation(2008BADB3B09-03)
文摘Three varieties were employed as materials to study changes of photosynthetic traits under low-temperature stress. The results showed that Pn, Gs and Tr decreased under low-temperature treatment. Ci decreased under low-temperature treatment 18℃/ 9℃, and 16℃/7℃, and it decreased in earlier stage after increased under 14℃/5℃. WUE was increased in earlier stage and after stabilized. The order of the three varieties of cold resistance were Jinyu 5〉Xingken 3〉Jidan 198. They could make self-regulation through adjusting Gs, Tr, Ci and WUE.
基金Project(2010GXNSFA013029) supported by the Natural Science Foundation of Guangxi Province,ChinaProject(101059529) supported by National Undergraduate Innovation Program of the Ministry of Education of China
文摘The influences of BaCu（B2O5） （BCB） addition on sintering, microstructure and microwave dielectric properties of Li2MgTi308 ceramics were investigated using X-ray diffractometry, scanning electron microscopy and microwave dielectric measurements. The experimental results show that a small amount of BaCu（B2O5） addition can effectively reduce the sintering temperature to 900℃, and induce only a limited degradation of the microwave dielectric properties. Typically, the best microwave dielectric properties of er24.5, Q×f =24 622 GHz, rf=4.2×10-6℃ -1 are obtained for 1.0% BCB-doped Li2MgTi3O8 ceramics sintered at 900℃ for 3 h. The BCB-doped Li2MgTi3O8 ceramics can be compatible with Ag electrode, which may be a strong candidate for low temperature co-fired ceramics applications.
基金Projects(51074190,51234009)supported by the National Natural Science Foundation of ChinaProject(2014DFA90520)supported by International Cooperation Program of Ministry of Science of ChinaProject(20110162110049)supported by the Doctoral Scientific Fund Project of the Ministry of Education of China
文摘A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.
基金Project(BE2015628)supported by Jiangsu Province Science and Technology Support Program,China
文摘Considering that Fe,Al elements in bauxite residue are active components for water purification,an effective polyaluminum ferric chloride(PAFC)coagulant derived from bauxite residue,with Fe2O3 content>5.1%,Al2O3%>6.5%,basicity>65%,was successfully prepared.The effect of as-prepared PAFC on the zeta potential for printing and dyeing wastewater was investigated.Comparing with polyferric chloride(PFC)and polyferric sulfate(PFS)for printing and dyeing wastewater treatment,prepared bauxite residue-based PAFC exhibited the optimal performance in the aspects of chromaticity and chemical oxygen demand(COD)removal rate.Furthermore,the combination of bauxite residue-based PAFC and PFS for synergy coagulation of such wastewater demonstrated an obvious positive effect.With the proportion between as-prepared PAFC and PFS to be 2.5:1,the COD of treated wastewater could be further reduced to meet the national level A standard of China,providing a promising route to solve the problem of substandard printing and dyeing sewage outfall by a simple coagulation strategy.
基金Project(2008A09030004) supported by the Major Science and Technology Project of Guangdong Province,ChinaProject(30815009) supported by the Foundation of State Key Laboratory of Advanced Design and Manufacture for Vehicle Body
文摘The hot compression test of 6063 Al alloy was performed on a Gleeble-1500 thermo-simulation machine, and the forming of 6063 rod cxtrudate in low-temperature high-speed extrusion was simulated with extrusion ratio of 25 on the platform of DEFORM 2D successfully. From the compression experimental results, the flow stress model of this Al alloy is obtained which could be the constitutive equation in the simulation of low-temperature high-speed extrusion process. From the numerical simulation results, there is a higher strain concentration at the entrance of the die and the exit temperature reaches up to 522 ℃ in low-temperature high-speed extrusion, which approaches to the quenching temperature of the 6063 Al alloy. The results show that the low-temperature high-speed extrusion method as a promsing one can reduce energy consumption effectively.
文摘Studies on the cold-responsive genes and cold signaling of woody species drop far behind in comparison to herbaceous plants.Due to similar lignified structure,perennial characteristic,and enhanced tolerance,it seems much easier to find strongly antifreeze genes and obtain effective results in transgenic woody plants.In this study,Ammopiptanthus mongolicus,an evergreen,broadleaf and cold-resist leguminous shrub growing in the desert of Inner Mongolia,was used as a material for low-temperature induced gene isolation.Through differential expression analysis induced by low-temperature,thirteen up-regulated cDNAs were identified.One of them,AmEBP1,(accession number:DQ519359)confers enhanced cold-tolerance to both transgenic E.coli and transgenic Arabidopsis.Results suggest that AmEBP1 can stimulate the synthesis of ribosome and the dephosphyration of the α-subunit of initiation factor 2(eIF2α),and subsequently promote the translation process.By which the transgenic plants obtained increased cold-resistant ability.
文摘1IntroductionThe dyeing and finishing process is animportant step in textile processing,which makes great contribution to theadded-value of textile and garment.The Chinese government and the textilecircles attach great importance to thedevelopment of the dyeing and finishingindustry.It has been listed as one of in-dustries that will get major support fromthe state In the last few years,sincethe government has given it
文摘Coacervation of oxidized glutathione(GSSG)and a cationic surfactant,didodecyldimethylammonium bromide(DDAB),was constructed mainly driven by the electrostatic and hydrophobic interactions.The pH-dependent coacervate of GSSG-DDAB(1∶4,mol/mol)was analyzed.Under acidic and neutral conditions,a turbid suspension of droplets is observed,and alkaline pH results in the phase separation of coacervates as the top phase.The coacervate phase exhibits good performance(extraction efficiency>85%)in extracting several dyes from water,including brilliant yellow,acid red 13,cresyl violet acetate,eriochrom blue SE,and 4-hydroxyazobenzene.The dyes are added into the suspension in acidic conditions.Then,the dyes are enriched and extracted along with the coacervates as the top phase when pH is adjusted to~10.Coacervation of GSSG with DDAB provides a simple approach to extract organic pollutants in wastewater treatment.
