To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a b...To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a benchmark scramjet performance evaluation model.Based on the test data of typical flying point of Mach 7 with the altitude of 29 km,the reliability of the model was verified.The deviations of parameters such as the to⁃tal pressure loss of combustor between the model and the test data were analyzed.Furtherly,an analytical method for post-combustion magnetohydrodynamic power generation was established;by embedding the above method into the overall performance evaluation model,performance prediction considering the power generation effect was realized.Finally,based on the above model,variety regulations of the inlet and the outlet parameters of the power generation channel and performance parameters including the engine specific impulse and the unit thrust under different enthalpy extraction ratios and load factors were analyzed.It could be concluded that the model can reliably predict the variations of key parameters.As the value of the load factor increases,the value of the conduc⁃tivity required to reach the specified enthalpy extraction ratio first decreases and then increases,which is approxi⁃mately parabolic.In order to reduce the demand for the gas conductivity for MHD power generation,the load fac⁃tor should be around 0.5.When the load factor is 0.4 and the magnetic induction intensity is 2.5 T,if the enthalpy extraction ratio reaches 0.5%,the engine specific impulse performance reduces about 3.58%.展开更多
To scientifically evaluate the restoration performance of ancient city walls,Terahertz time-domain spectroscopy(THz-TDS)and infrared thermal imaging technology were applied to assess the Desheng Fortress(Ming Dynasty)...To scientifically evaluate the restoration performance of ancient city walls,Terahertz time-domain spectroscopy(THz-TDS)and infrared thermal imaging technology were applied to assess the Desheng Fortress(Ming Dynasty).Three representative sections were examined:adobe brick masonry repaired(Area 1),well-preserved original(Area 2),and layer-by-layer ramming repaired(Area 3).THz spectral data revealed significant differences between Area 1(time delay:3.72 ps;refractive index:2.224)and Area 2(time delay:3.02 ps;refractive index:2.107),while Area 3(time delay:3.12 ps;refractive index:2.098)demonstrated nearly identical THz spectral data to Area 2.Infrared thermal imaging also showed that the Area 3 restored by layer-by-layer ramming exhibited greater uniformity with fewer instances of cracks,capillary phenomena,or biological diseases.The proposed point-surface integrated evaluation methodology synergistically combines infrared thermography mapping of heritage surfaces with THz spectral datasets acquired through in-situ micro-sampling,enabling quantitative restoration assessment and providing a novel approach for scientifically validating traditional conservation techniques.展开更多
The use of ultra-high molecular weight polyethylene(UHMWPE)composite in the design of lightweight protective equipment,has gained a lot of interest.However,there is an urgent need to understand the ballistic response ...The use of ultra-high molecular weight polyethylene(UHMWPE)composite in the design of lightweight protective equipment,has gained a lot of interest.However,there is an urgent need to understand the ballistic response mechanism and theoretical prediction model of performance.This paper explores the ballistic response mechanism of UHMWPE composite through experimental and simulation analyses.Then,a resistance-driven modeling method was proposed to establish a theoretical model for predicting the bulletproof performance.The ballistic response mechanism of UHMWPE composite encompassed three fundamental modes:local response,structural response,and coupled response.The occurrence ratio of these fundamental response modes during impact was dependent on the projectile velocity and laminate thickness.The bulletproof performance of laminate under different response modes was assessed based on the penetration depth of the projectile,the bulging height on the rear face of the laminate,the thickness of remaining sub-laminate,and residual velocity of the projectile.The absolute deviations of bulletproof performance indicator between theoretical value and experimental value were well within 11.13%,demonstrating that the established evaluation model possessed high degree of prediction accuracy.展开更多
The combustion process of pulverized coal injected into blast furnace involves a lot of physical and chemical reactions. Based on the combustion behaviors of pulverized coal, the conception of coal effective calorific...The combustion process of pulverized coal injected into blast furnace involves a lot of physical and chemical reactions. Based on the combustion behaviors of pulverized coal, the conception of coal effective calorific value representing the actual thermal energy provided for blast furnace was proposed. A cost performance evaluation model of coal injection was built up for the optimal selection of various kinds of coal based on effective calorific value. The model contains two indicators: coal effective calorific value which has eight sub-indicators and coal injection cost which includes four sub-indicators. In addition, the calculation principle and application of cost performance evaluation model in a Chinese large-scale iron and steel company were comprehensively introduced. The evaluation results finally confirm that this novel model is of great significance to the optimal selection of blast furnace pulverized coal.展开更多
The optimal selection of radar clutter model is the premise of target detection,tracking,recognition,and cognitive waveform design in clutter background.Clutter characterization models are usually derived by mathemati...The optimal selection of radar clutter model is the premise of target detection,tracking,recognition,and cognitive waveform design in clutter background.Clutter characterization models are usually derived by mathematical simplification or empirical data fitting.However,the lack of standard model labels is a challenge in the optimal selection process.To solve this problem,a general three-level evaluation system for the model selection performance is proposed,including model selection accuracy index based on simulation data,fit goodness indexs based on the optimally selected model,and evaluation index based on the supporting performance to its third-party.The three-level evaluation system can more comprehensively and accurately describe the selection performance of the radar clutter model in different ways,and can be popularized and applied to the evaluation of other similar characterization model selection.展开更多
On the basis of analyzing the typical waste collection and transportation mode,the evaluation index system for performance of the waste collection and transportation system was proposed with three grades,which related...On the basis of analyzing the typical waste collection and transportation mode,the evaluation index system for performance of the waste collection and transportation system was proposed with three grades,which related to six factors,such as economic evaluation,high efficient evaluation,environmental impact assessment,resource evaluation,evaluation of security and emergency,evaluation of management and society. With the performance evaluation theory,the performance evaluation model of waste collection and transportation system was constructed,which quantified the grading standard of index and determined the index weight in analytic hierarchy process (AHP). After evaluating the waste collection and transportation system of the main districts of Chongqing city,the results show that the it has an excellent performance evaluation grade with very high performance level of three indices involving evaluation of management and society,environmental impact assessment,evaluation of security and emergency and quite low performance level of two indices that include high efficient evaluation and economic evaluation.展开更多
This paper,using pseudo-conservation laws in cyclic-service systems, derives some expressions for the weighted sum of the mean waiting time token ring networks with exhaustive limitedservice policies on condition that...This paper,using pseudo-conservation laws in cyclic-service systems, derives some expressions for the weighted sum of the mean waiting time token ring networks with exhaustive limitedservice policies on condition that messages arrived with batch Poisson, and discusses boundary conditions. At the same time, the results of the token ring network with exhaustive and non-exhaustiveservice strategy are obtained. Finally the exact expression of mean waiting time in symmetric ringnetwork with same service strategy is given.展开更多
To evaluate the performance of real time kinematic (RTK) network algorithms without applying actual measurements, a new method called geometric precision evaluation methodology (GPEM) based on covariance analysis was ...To evaluate the performance of real time kinematic (RTK) network algorithms without applying actual measurements, a new method called geometric precision evaluation methodology (GPEM) based on covariance analysis was presented. Three types of multiple reference station interpolation algorithms, including partial derivation algorithm (PDA), linear interpolation algorithms (LIA) and least squares condition (LSC) were discussed and analyzed. The geometric dilution of precision (GDOP) was defined to describe the influence of the network geometry on the interpolation precision, and the different GDOP expressions of above-mentioned algorithms were deduced. In order to compare geometric precision characteristics among different multiple reference station network algorithms, a simulation was conducted, and the GDOP contours of these algorithms were enumerated. Finally, to confirm the validation of GPEM, an experiment was conducted using data from Unite State Continuously Operating Reference Stations (US-CORS), and the precision performances were calculated according to the real test data and GPEM, respectively. The results show that GPEM generates very accurate estimation of the performance compared to the real data test.展开更多
A set of water powered excavation test system was developed for the comprehensive performance testing and evaluation of water powered percussive rock drill indoors. The whole system contains hydraulic power section, e...A set of water powered excavation test system was developed for the comprehensive performance testing and evaluation of water powered percussive rock drill indoors. The whole system contains hydraulic power section, electronic control system, test and data acquisition system, and assistant devices, such as guideway and drilling bench. Parameters of the water powered percussive rock drill can be obtained by analyzing testing data, which contain impact energy, front and back cavity pressure, pressure and flow in each working part, drilling velocity, frequency and energy efficiency etc. The system is applied to test the self-designed water powered percussive rock drill SYYG65. The parameters of water powered percussive rock drill with impact pressure of about 8.9 MPa are 58.93 J for impact energy, and 8.97% for energy efficiency, which prove the effectiveness of system.展开更多
Satellite constellation design for space optical systems is essentially a multiple-objective optimization problem. In this work, to tackle this challenge, we first categorize the performance metrics of the space optic...Satellite constellation design for space optical systems is essentially a multiple-objective optimization problem. In this work, to tackle this challenge, we first categorize the performance metrics of the space optical system by taking into account the system tasks（i.e., target detection and tracking）. We then propose a new non-dominated sorting genetic algorithm（NSGA） to maximize the system surveillance performance. Pareto optimal sets are employed to deal with the conflicts due to the presence of multiple cost functions. Simulation results verify the validity and the improved performance of the proposed technique over benchmark methods.展开更多
To generate a test set for a given circuit (including both combinational and sequential circuits), choice of an algorithm within a number of existing test generation algorithms to apply is bound to vary from circuit t...To generate a test set for a given circuit (including both combinational and sequential circuits), choice of an algorithm within a number of existing test generation algorithms to apply is bound to vary from circuit to circuit. In this paper, the genetic algorithms are used to construct the models of existing test generation algorithms in making such choice more easily. Therefore, we may forecast the testability parameters of a circuit before using the real test generation algorithm. The results also can be used to evaluate the efficiency of the existing test generation algorithms. Experimental results are given to convince the readers of the truth and the usefulness of this approach.展开更多
To develop a better approach for spatial evaluation of drinking water quality, an intelligent evaluation method integrating a geographical information system(GIS) and an ant colony clustering algorithm(ACCA) was used....To develop a better approach for spatial evaluation of drinking water quality, an intelligent evaluation method integrating a geographical information system(GIS) and an ant colony clustering algorithm(ACCA) was used. Drinking water samples from 29 wells in Zhenping County, China, were collected and analyzed. 35 parameters on water quality were selected, such as chloride concentration, sulphate concentration, total hardness, nitrate concentration, fluoride concentration, turbidity, pH, chromium concentration, COD, bacterium amount, total coliforms and color. The best spatial interpolation methods for the 35 parameters were found and selected from all types of interpolation methods in GIS environment according to the minimum cross-validation errors. The ACCA was improved through three strategies, namely mixed distance function, average similitude degree and probability conversion functions. Then, the ACCA was carried out to obtain different water quality grades in the GIS environment. In the end, the result from the ACCA was compared with those from the competitive Hopfield neural network(CHNN) to validate the feasibility and effectiveness of the ACCA according to three evaluation indexes, which are stochastic sampling method, pixel amount and convergence speed. It is shown that the spatial water quality grades obtained from the ACCA were more effective, accurate and intelligent than those obtained from the CHNN.展开更多
System-of-systems （SOS） engineering involves a com- plex process of refining high-level SoS requirements into more detailed systems requirements and assessing the extent to which the performances of to-be systems ma...System-of-systems （SOS） engineering involves a com- plex process of refining high-level SoS requirements into more detailed systems requirements and assessing the extent to which the performances of to-be systems may possibly satisfy SoS capa- bility objectives. The key issue is how to model such requirements to automate the process of analysis and assessment. This paper suggests a meta-model that defines both functional and non- functional features of SoS requirements for command and control, communication, computer, intelligence, surveillance reconnais- sance （C41SR） systems. A domain-specific modeling language is defined by extending unified modeling language （UML） con- structed of class and association with fuzzy theory in order to model the fuzzy concepts of performance requirements. An effi- ciency evaluation function is introduced, based on Bezier curves, to predict the effectiveness of systems. An algorithm is presented to transform domain models in fuzzy UML into a requirements ontology in description logic （DL） so that requirements verification can be automated with a popular DL reasoner such as Pellet.展开更多
Automatic modulation classification is the process of identification of the modulation type of a signal in a general environment. This paper proposes a new method to evaluate the tracking performance of large margin c...Automatic modulation classification is the process of identification of the modulation type of a signal in a general environment. This paper proposes a new method to evaluate the tracking performance of large margin classifier against signal-tonoise ratio （SNR）, and classifies all forms of primary user＇s signals in a cognitive radio environment. For achieving this objective, two structures of a large margin are developed in additive white Gaussian noise （AWGN） channels with priori unknown SNR. A combination of higher order statistics and instantaneous characteristics is selected as effective features. Simulation results show that the classification rates of the proposed structures are well robust against environmental SNR changes.展开更多
A projection pursuit model is presented in this paper for comprehensive evaluation of benefits of small watershed control.By using the model,small watershed control samples with many benefit evaluation indexes can be ...A projection pursuit model is presented in this paper for comprehensive evaluation of benefits of small watershed control.By using the model,small watershed control samples with many benefit evaluation indexes can be synthesized projective values with one dimension.The samples can be naturally evaluated according to the projective values.The parameters of the model is optimized by using real coding beased accelerating genetic aglrothm,which overcomes the shortcomings of large computation amount and difficulty of computer programming in traditional projection prusuit methods,and provides a new way for wide applications of projection pursuit technique to different evaluation problems in agricultural systems engineering.展开更多
The widespread 5G base stations can be potential jammers for the vulnerable BeiDou B1I receivers due to its low power.Therefore,a novel analytical model is derived for the 5G signal to evaluate its impact on acquisiti...The widespread 5G base stations can be potential jammers for the vulnerable BeiDou B1I receivers due to its low power.Therefore,a novel analytical model is derived for the 5G signal to evaluate its impact on acquisition performance under three decision methods.The good agreement between the Monte Carlo method(MCM)through software defined receiver(SDR)and the derived expressions validates the effectiveness of the proposed algorithm.It can be found that the receivers exhibit varied responses for different 5G waveforms and decision strategies.The receiver also shows the least endurances for some kind of 5G waveforms,however,this kind of adverse effect can be cancelled by a reduced interference signal ratio(ISR),an increased integration time or a larger accumulation times.展开更多
文摘To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a benchmark scramjet performance evaluation model.Based on the test data of typical flying point of Mach 7 with the altitude of 29 km,the reliability of the model was verified.The deviations of parameters such as the to⁃tal pressure loss of combustor between the model and the test data were analyzed.Furtherly,an analytical method for post-combustion magnetohydrodynamic power generation was established;by embedding the above method into the overall performance evaluation model,performance prediction considering the power generation effect was realized.Finally,based on the above model,variety regulations of the inlet and the outlet parameters of the power generation channel and performance parameters including the engine specific impulse and the unit thrust under different enthalpy extraction ratios and load factors were analyzed.It could be concluded that the model can reliably predict the variations of key parameters.As the value of the load factor increases,the value of the conduc⁃tivity required to reach the specified enthalpy extraction ratio first decreases and then increases,which is approxi⁃mately parabolic.In order to reduce the demand for the gas conductivity for MHD power generation,the load fac⁃tor should be around 0.5.When the load factor is 0.4 and the magnetic induction intensity is 2.5 T,if the enthalpy extraction ratio reaches 0.5%,the engine specific impulse performance reduces about 3.58%.
文摘To scientifically evaluate the restoration performance of ancient city walls,Terahertz time-domain spectroscopy(THz-TDS)and infrared thermal imaging technology were applied to assess the Desheng Fortress(Ming Dynasty).Three representative sections were examined:adobe brick masonry repaired(Area 1),well-preserved original(Area 2),and layer-by-layer ramming repaired(Area 3).THz spectral data revealed significant differences between Area 1(time delay:3.72 ps;refractive index:2.224)and Area 2(time delay:3.02 ps;refractive index:2.107),while Area 3(time delay:3.12 ps;refractive index:2.098)demonstrated nearly identical THz spectral data to Area 2.Infrared thermal imaging also showed that the Area 3 restored by layer-by-layer ramming exhibited greater uniformity with fewer instances of cracks,capillary phenomena,or biological diseases.The proposed point-surface integrated evaluation methodology synergistically combines infrared thermography mapping of heritage surfaces with THz spectral datasets acquired through in-situ micro-sampling,enabling quantitative restoration assessment and providing a novel approach for scientifically validating traditional conservation techniques.
基金supported by the National Key Research and Development of China(Grant No.2022YFB4601901)the National Natural Science Foundation of China(Grant No.12122202)。
文摘The use of ultra-high molecular weight polyethylene(UHMWPE)composite in the design of lightweight protective equipment,has gained a lot of interest.However,there is an urgent need to understand the ballistic response mechanism and theoretical prediction model of performance.This paper explores the ballistic response mechanism of UHMWPE composite through experimental and simulation analyses.Then,a resistance-driven modeling method was proposed to establish a theoretical model for predicting the bulletproof performance.The ballistic response mechanism of UHMWPE composite encompassed three fundamental modes:local response,structural response,and coupled response.The occurrence ratio of these fundamental response modes during impact was dependent on the projectile velocity and laminate thickness.The bulletproof performance of laminate under different response modes was assessed based on the penetration depth of the projectile,the bulging height on the rear face of the laminate,the thickness of remaining sub-laminate,and residual velocity of the projectile.The absolute deviations of bulletproof performance indicator between theoretical value and experimental value were well within 11.13%,demonstrating that the established evaluation model possessed high degree of prediction accuracy.
基金Project(51134008)supported by the National Natural Science Foundation of ChinaProject(2012CB720401)supported by the National Basic Research Program of China
文摘The combustion process of pulverized coal injected into blast furnace involves a lot of physical and chemical reactions. Based on the combustion behaviors of pulverized coal, the conception of coal effective calorific value representing the actual thermal energy provided for blast furnace was proposed. A cost performance evaluation model of coal injection was built up for the optimal selection of various kinds of coal based on effective calorific value. The model contains two indicators: coal effective calorific value which has eight sub-indicators and coal injection cost which includes four sub-indicators. In addition, the calculation principle and application of cost performance evaluation model in a Chinese large-scale iron and steel company were comprehensively introduced. The evaluation results finally confirm that this novel model is of great significance to the optimal selection of blast furnace pulverized coal.
基金the National Natural Science Foundation of China(6187138461921001).
文摘The optimal selection of radar clutter model is the premise of target detection,tracking,recognition,and cognitive waveform design in clutter background.Clutter characterization models are usually derived by mathematical simplification or empirical data fitting.However,the lack of standard model labels is a challenge in the optimal selection process.To solve this problem,a general three-level evaluation system for the model selection performance is proposed,including model selection accuracy index based on simulation data,fit goodness indexs based on the optimally selected model,and evaluation index based on the supporting performance to its third-party.The three-level evaluation system can more comprehensively and accurately describe the selection performance of the radar clutter model in different ways,and can be popularized and applied to the evaluation of other similar characterization model selection.
基金Project (2006BAC06B02-01) supported by the National Key Technology R&D Program in the 11th Five-Year Plan Period of China
文摘On the basis of analyzing the typical waste collection and transportation mode,the evaluation index system for performance of the waste collection and transportation system was proposed with three grades,which related to six factors,such as economic evaluation,high efficient evaluation,environmental impact assessment,resource evaluation,evaluation of security and emergency,evaluation of management and society. With the performance evaluation theory,the performance evaluation model of waste collection and transportation system was constructed,which quantified the grading standard of index and determined the index weight in analytic hierarchy process (AHP). After evaluating the waste collection and transportation system of the main districts of Chongqing city,the results show that the it has an excellent performance evaluation grade with very high performance level of three indices involving evaluation of management and society,environmental impact assessment,evaluation of security and emergency and quite low performance level of two indices that include high efficient evaluation and economic evaluation.
文摘This paper,using pseudo-conservation laws in cyclic-service systems, derives some expressions for the weighted sum of the mean waiting time token ring networks with exhaustive limitedservice policies on condition that messages arrived with batch Poisson, and discusses boundary conditions. At the same time, the results of the token ring network with exhaustive and non-exhaustiveservice strategy are obtained. Finally the exact expression of mean waiting time in symmetric ringnetwork with same service strategy is given.
基金Project(61273055) supported by the National Natural Science Foundation of ChinaProject(CX2010B012) supported by Hunan Provincial Innovation Foundation for Postgraduate Students, ChinaProject(B100302) supported by Innovation Foundation for Postgraduate Students of National University of Defense Technology, China
文摘To evaluate the performance of real time kinematic (RTK) network algorithms without applying actual measurements, a new method called geometric precision evaluation methodology (GPEM) based on covariance analysis was presented. Three types of multiple reference station interpolation algorithms, including partial derivation algorithm (PDA), linear interpolation algorithms (LIA) and least squares condition (LSC) were discussed and analyzed. The geometric dilution of precision (GDOP) was defined to describe the influence of the network geometry on the interpolation precision, and the different GDOP expressions of above-mentioned algorithms were deduced. In order to compare geometric precision characteristics among different multiple reference station network algorithms, a simulation was conducted, and the GDOP contours of these algorithms were enumerated. Finally, to confirm the validation of GPEM, an experiment was conducted using data from Unite State Continuously Operating Reference Stations (US-CORS), and the precision performances were calculated according to the real test data and GPEM, respectively. The results show that GPEM generates very accurate estimation of the performance compared to the real data test.
基金Project(2006AA06Z134) supported by the National High Technology Research and Development Program of ChinaProjects(50934006, 50904079) supported by the National Natural Science Foundation of China
文摘A set of water powered excavation test system was developed for the comprehensive performance testing and evaluation of water powered percussive rock drill indoors. The whole system contains hydraulic power section, electronic control system, test and data acquisition system, and assistant devices, such as guideway and drilling bench. Parameters of the water powered percussive rock drill can be obtained by analyzing testing data, which contain impact energy, front and back cavity pressure, pressure and flow in each working part, drilling velocity, frequency and energy efficiency etc. The system is applied to test the self-designed water powered percussive rock drill SYYG65. The parameters of water powered percussive rock drill with impact pressure of about 8.9 MPa are 58.93 J for impact energy, and 8.97% for energy efficiency, which prove the effectiveness of system.
文摘Satellite constellation design for space optical systems is essentially a multiple-objective optimization problem. In this work, to tackle this challenge, we first categorize the performance metrics of the space optical system by taking into account the system tasks（i.e., target detection and tracking）. We then propose a new non-dominated sorting genetic algorithm（NSGA） to maximize the system surveillance performance. Pareto optimal sets are employed to deal with the conflicts due to the presence of multiple cost functions. Simulation results verify the validity and the improved performance of the proposed technique over benchmark methods.
基金This work was supported by National Natural Science Foundation of China (NSFC) under the grant !No. 69873030
文摘To generate a test set for a given circuit (including both combinational and sequential circuits), choice of an algorithm within a number of existing test generation algorithms to apply is bound to vary from circuit to circuit. In this paper, the genetic algorithms are used to construct the models of existing test generation algorithms in making such choice more easily. Therefore, we may forecast the testability parameters of a circuit before using the real test generation algorithm. The results also can be used to evaluate the efficiency of the existing test generation algorithms. Experimental results are given to convince the readers of the truth and the usefulness of this approach.
基金Projects(41161020,41261026) supported by the National Natural Science Foundation of ChinaProject(BQD2012013) supported by the Research starting Funds for Imported Talents,Ningxia University,China+1 种基金Project(ZR1209) supported by the Natural Science Funds,Ningxia University,ChinaProject(NGY2013005) supported by the Key Science Project of Colleges and Universities in Ningxia,China
文摘To develop a better approach for spatial evaluation of drinking water quality, an intelligent evaluation method integrating a geographical information system(GIS) and an ant colony clustering algorithm(ACCA) was used. Drinking water samples from 29 wells in Zhenping County, China, were collected and analyzed. 35 parameters on water quality were selected, such as chloride concentration, sulphate concentration, total hardness, nitrate concentration, fluoride concentration, turbidity, pH, chromium concentration, COD, bacterium amount, total coliforms and color. The best spatial interpolation methods for the 35 parameters were found and selected from all types of interpolation methods in GIS environment according to the minimum cross-validation errors. The ACCA was improved through three strategies, namely mixed distance function, average similitude degree and probability conversion functions. Then, the ACCA was carried out to obtain different water quality grades in the GIS environment. In the end, the result from the ACCA was compared with those from the competitive Hopfield neural network(CHNN) to validate the feasibility and effectiveness of the ACCA according to three evaluation indexes, which are stochastic sampling method, pixel amount and convergence speed. It is shown that the spatial water quality grades obtained from the ACCA were more effective, accurate and intelligent than those obtained from the CHNN.
基金supported by the National Natural Science Foundation of China(61273210)
文摘System-of-systems （SOS） engineering involves a com- plex process of refining high-level SoS requirements into more detailed systems requirements and assessing the extent to which the performances of to-be systems may possibly satisfy SoS capa- bility objectives. The key issue is how to model such requirements to automate the process of analysis and assessment. This paper suggests a meta-model that defines both functional and non- functional features of SoS requirements for command and control, communication, computer, intelligence, surveillance reconnais- sance （C41SR） systems. A domain-specific modeling language is defined by extending unified modeling language （UML） con- structed of class and association with fuzzy theory in order to model the fuzzy concepts of performance requirements. An effi- ciency evaluation function is introduced, based on Bezier curves, to predict the effectiveness of systems. An algorithm is presented to transform domain models in fuzzy UML into a requirements ontology in description logic （DL） so that requirements verification can be automated with a popular DL reasoner such as Pellet.
文摘Automatic modulation classification is the process of identification of the modulation type of a signal in a general environment. This paper proposes a new method to evaluate the tracking performance of large margin classifier against signal-tonoise ratio （SNR）, and classifies all forms of primary user＇s signals in a cognitive radio environment. For achieving this objective, two structures of a large margin are developed in additive white Gaussian noise （AWGN） channels with priori unknown SNR. A combination of higher order statistics and instantaneous characteristics is selected as effective features. Simulation results show that the classification rates of the proposed structures are well robust against environmental SNR changes.
基金Foundation Item:Chinese N ational Natural Science Fund and Yantze Water Resouces Comm ission U nion Project(N o.5 0 0 996 2 0 ) Chinese National N atural Science Fund Project(No.4 98710 18)
文摘A projection pursuit model is presented in this paper for comprehensive evaluation of benefits of small watershed control.By using the model,small watershed control samples with many benefit evaluation indexes can be synthesized projective values with one dimension.The samples can be naturally evaluated according to the projective values.The parameters of the model is optimized by using real coding beased accelerating genetic aglrothm,which overcomes the shortcomings of large computation amount and difficulty of computer programming in traditional projection prusuit methods,and provides a new way for wide applications of projection pursuit technique to different evaluation problems in agricultural systems engineering.
文摘The widespread 5G base stations can be potential jammers for the vulnerable BeiDou B1I receivers due to its low power.Therefore,a novel analytical model is derived for the 5G signal to evaluate its impact on acquisition performance under three decision methods.The good agreement between the Monte Carlo method(MCM)through software defined receiver(SDR)and the derived expressions validates the effectiveness of the proposed algorithm.It can be found that the receivers exhibit varied responses for different 5G waveforms and decision strategies.The receiver also shows the least endurances for some kind of 5G waveforms,however,this kind of adverse effect can be cancelled by a reduced interference signal ratio(ISR),an increased integration time or a larger accumulation times.
