Multidimensional integration and multifunctional com-ponent assembly have been greatly explored in recent years to extend Moore’s Law of modern microelectronics.However,this inevitably exac-erbates the inhomogeneity ...Multidimensional integration and multifunctional com-ponent assembly have been greatly explored in recent years to extend Moore’s Law of modern microelectronics.However,this inevitably exac-erbates the inhomogeneity of temperature distribution in microsystems,making precise temperature control for electronic components extremely challenging.Herein,we report an on-chip micro temperature controller including a pair of thermoelectric legs with a total area of 50×50μm^(2),which are fabricated from dense and flat freestanding Bi2Te3-based ther-moelectric nano films deposited on a newly developed nano graphene oxide membrane substrate.Its tunable equivalent thermal resistance is controlled by electrical currents to achieve energy-efficient temperature control for low-power electronics.A large cooling temperature difference of 44.5 K at 380 K is achieved with a power consumption of only 445μW,resulting in an ultrahigh temperature control capability over 100 K mW^(-1).Moreover,an ultra-fast cooling rate exceeding 2000 K s^(-1) and excellent reliability of up to 1 million cycles are observed.Our proposed on-chip temperature controller is expected to enable further miniaturization and multifunctional integration on a single chip for microelectronics.展开更多
The sheet size of a graphene oxide （GO） can greatly influence its electrical, optical, mechanical, electrochemical and catalytic property. It is a key challenge to how to control the sheet size during its preparatio...The sheet size of a graphene oxide （GO） can greatly influence its electrical, optical, mechanical, electrochemical and catalytic property. It is a key challenge to how to control the sheet size during its preparation in different application fields. According to our previous theoretical calculations of the effect of temperature on the oxidation process of graphene, we use Hummers method to prepare GOs with different sheet sizes by simply controlling the temperature condition in the process of the oxidation reaction of potassium permanganate （KMnO4） with graphene and the dilution process with deionized water. The results detected by transmission electron microscopy （TEM） and atomic force microscopy （AFM） show that the average sizes of GO sheets prepared at different temperatures are about 1 μm and 7 μm respectively. The ultraviolet-visible spectroscopy （UV-vis） shows that lower temperature can lead to smaller oxidation degrees of GO and less oxygen functional groups on the surface. In addition, we prepare GO membranes to test their mechanical strengths by ultrasonic waves, and we find that the strengths of the GO membranes prepared under low temperatures are considerably higher than those prepared under high temperatures, showing the high mechanical strengths of larger GO sheets. Our experimental results testify our previous theoretical calculations. Compared with the traditional centrifugal separation and chemical cutting method, the preparation process of GO by temperature control is simple and low-cost and also enables large-size synthesis. These findings develop a new method to control GO sheet sizes for large-scale potential applications.展开更多
A neural adaptive proportion sum differential (PSD) algorithm with errors prediction is researched. It is applied in inertial navigation system(INS) temperature control. The algorithm do not need the process's pre...A neural adaptive proportion sum differential (PSD) algorithm with errors prediction is researched. It is applied in inertial navigation system(INS) temperature control. The algorithm do not need the process's precise mathematical model and can adapt to the process parameters changing, and can deal with the process with nonlinearity. According to the Smith predictor, author developed a method that takes the predicted process error and error change as neural adaptive PSD algorithm's input. The method is effective to the system with long dead time. The results of compute simulation show that this system has characters of quickly reaction, low overshoot and good stability. It can meet the requirements of temperature control of INS.展开更多
Temperature control curve is the key to achieving temperature control and crack prevention of high concrete dam during construction,and its rationality depends on the accurate measurement of temperature stress.With th...Temperature control curve is the key to achieving temperature control and crack prevention of high concrete dam during construction,and its rationality depends on the accurate measurement of temperature stress.With the simulation testing machine for the temperature stress,in the present study,we carried out the deformation process tests of concrete under three temperature curves:convex,straight and concave.Besides,we not only measured the early-age elastic modulus,creep parameters and stress process,but also proposed the preferred type.The results show that at early age,higher temperature always leads to greater elastic modulus and smaller creep.However,the traditional indoor experiments have underestimated the elastic modulus and creep development at early age,which makes the calculated value of temperature stress too small,thus increasing the cracking risk.In this study,the stress values of the three curves calculated based on the strain and early-age parameters are in good agreement with the temperature stress measured by the temperature stress testing machine,which verifies the method accuracy.When the temperature changes along the concave curve,the law of stress development is in consistent with that of strength.Under this condition,the stress fluctuation is small and the crack prevention safety of the concave type is higher,so the concave type is better.The test results provide a reliable basis and support for temperature control curve design and optimization of concrete dams.展开更多
A new intelligent temperature control system for stove was introduced. It could accomplish A/D conversion, data processing, output displaying and alarming while the temperature exceeds the given threshold. The tempera...A new intelligent temperature control system for stove was introduced. It could accomplish A/D conversion, data processing, output displaying and alarming while the temperature exceeds the given threshold. The temperature adjusting devices were bi direction SCR and heating resistor. The hardware and software were discussed in the paper.展开更多
Considering some characteristics of large-scale standing quench furnace, such as great heat inertia, evident time lag, strong coupling influence, hard to establish exact mathematical models of plant and etc, an artifi...Considering some characteristics of large-scale standing quench furnace, such as great heat inertia, evident time lag, strong coupling influence, hard to establish exact mathematical models of plant and etc, an artificial intelligent fuzzy control algorithm is put forward in this paper. Through adjusting the on-off ratio of electric heating elements, the temperature in furnace is controlled accurately. This paper describes structure and qualities of the large-scale standing quench furnace briefly, introduces constitution of control system, and expounds principle and implementation of intelligent control algorithm. The applied results prove that the intelligent control system can completely satisfy the technological requirements. Namely, it can realize fast increasing temperature with a little overshoot, exact holding temperature, and well-distributed temperature in quench furnace. It has raised the output and quality of aluminum material, and brought the outstanding economic and social benefits.展开更多
A structure of central air conditioning system in building and its running pattern are proposed in order to perform optimum energy saving strategy. The design of room temperature controller is taken as an example to d...A structure of central air conditioning system in building and its running pattern are proposed in order to perform optimum energy saving strategy. The design of room temperature controller is taken as an example to discuss the design of fuzzy controller using common microprogrammed control unit (MCU) in detail. Based on fuzzy theory the query control tables fixed in read only memory (ROM) of MCU are established to realize the energy saving in the room temperature controller and the reasoning procedure is analyzed. The diagram of hardware design and the flow chart of software of room temperature controller are presented. The results show that the proposed method is practical and effective to achieve the energy saving goal.展开更多
Combining oven controlled technique,digital compensation,high-resolution frequency difference measurement and self-calibration technique,a new design method of precise oven controlled crystal oscillator（OCXO） is pro...Combining oven controlled technique,digital compensation,high-resolution frequency difference measurement and self-calibration technique,a new design method of precise oven controlled crystal oscillator（OCXO） is proposed.Fine compensation is made in the vicinity of the crystal temperature inflection point by using the non-real-time temperature compensation strategy,and self-calibration system is integrated in the crystal.The method improves the digital compensated phase noise,simplifies the traditional OCXO development system,reduces the cost and shortens the developing cycle.Experiment results show that with a standard reference signal and self-calibration updated data,the oscillator can work stable and achieve its best performence.The performance index of crystal oscillator had an improvement with one to two orders of magnitude on the basis of original technical index.The method is widely used in the improvement of high-end crystal oscillator and atomic clock.展开更多
Prepreg stickiness is the adhesion between prepregs or between a prepreg and a mold in lay-up process.It is critical for automated fiber placement,because the stickiness should be small for smooth transport,as well as...Prepreg stickiness is the adhesion between prepregs or between a prepreg and a mold in lay-up process.It is critical for automated fiber placement,because the stickiness should be small for smooth transport,as well as large enough on the laying surface for a good placement performance.To ensure prepreg stickiness always being in the optimum laying window,placement temperature should be changed according to the laying speed.In our work,the relationship between laying speed and emissive power of heating lamp was studied.The heat transfer process between heating lamp and laying surface was analyzed and the control equation of dynamic temperature was derived.Finally,the infrared heating system was built and its effectiveness was verified based on placement experiment.展开更多
Thermoelectric devices(TEDs),including thermoelectric generators(TEGs) and thermoelectric coolers(TECs) based on the Seebeck and Peltier effects,respectively,are capable of converting heat directly into electricity an...Thermoelectric devices(TEDs),including thermoelectric generators(TEGs) and thermoelectric coolers(TECs) based on the Seebeck and Peltier effects,respectively,are capable of converting heat directly into electricity and vice versa.Tough suffering from low energy conversion efficiency and relatively high capital cost,TEDs have found niche applications,such as the remote power source for spacecraft,solid-state refrigerators,waste heat recycling,and so on.In particular,onchip integrable micro thermoelectric devices(μ-TEDs),which can realize local thermal management,on-site temperature sensing,and energy harvesting under minor temperature gradient,could play an important role in biological sensing and cell cultivation,self-powered Internet of Things(IoT),and wearable electronics.In this review,starting from the basic principles of thermoelectric devices,we summarize the most critical parameters for μ-TEDs,design guidelines,and most recent advances in the fabrication process.In addition,some innovative applications of μ-TEDs,such as in combination with microfluidics and photonics,are demonstrated in detail.展开更多
Heat conduction in single-walled carbon nanotubes （SWCNTs） has been investigated by using various methods, while less work has been focused on multi-walled carbon nanotubes （MWCNTs）. The thermal conductivities of ...Heat conduction in single-walled carbon nanotubes （SWCNTs） has been investigated by using various methods, while less work has been focused on multi-walled carbon nanotubes （MWCNTs）. The thermal conductivities of the double-walled carbon nanotubes （DWCNTs） with two different temperature control methods are studied by using molecular dynamics （MD） simulations. One case is that the heat baths （HBs） are imposed only on the outer wall, while the other is that the HBs are imposed on both the two walls. The results show that the ratio of the thermal conductivity of DWCNTs in the first case to that in the second case is inversely proportional to the ratio of the cross-sectional area of the DWCNT to that of its outer wall. In order to interpret the results and explore the heat conduction mechanisms, the inter-wall thermal transport of DWCNTs is simulated. Analyses of the temperature profiles of a DWCNT and its two walls in the two cases and the inter- wall thermal resistance show that in the first case heat is almost transported only along the outer wall, while in the second case a DWCNT behaves like parallel heat transport channels in which heat is transported along each wall independently. This gives a good explanation of our results and presents the heat conduction mechanisms of MWCNTs.展开更多
基金The authors thank D.Berger,D.Hofmann and C.Kupka in IFW Dresden for helpful technical support.H.R.acknowledges funding from the DFG(Deutsche Forschungsgemeinschaft)within grant number RE3973/1-1.Q.J.,H.R.and K.N.conceived the work.With the support from N.Y.and X.J.,Q.J.and T.G.fabricated the thermoelectric films and conducted the structural and compositional characterizations.Q.J.prepared microchips and fabricated the on-chip micro temperature controllers.Q.J.and N.P.carried out the temperature-dependent material and device performance measurements.Q.J.and H.R.performed the simulation and analytical calculations.Q.J.,H.R.and K.N.wrote the manuscript with input from the other coauthors.All the authors discussed the results and commented on the manuscript.
文摘Multidimensional integration and multifunctional com-ponent assembly have been greatly explored in recent years to extend Moore’s Law of modern microelectronics.However,this inevitably exac-erbates the inhomogeneity of temperature distribution in microsystems,making precise temperature control for electronic components extremely challenging.Herein,we report an on-chip micro temperature controller including a pair of thermoelectric legs with a total area of 50×50μm^(2),which are fabricated from dense and flat freestanding Bi2Te3-based ther-moelectric nano films deposited on a newly developed nano graphene oxide membrane substrate.Its tunable equivalent thermal resistance is controlled by electrical currents to achieve energy-efficient temperature control for low-power electronics.A large cooling temperature difference of 44.5 K at 380 K is achieved with a power consumption of only 445μW,resulting in an ultrahigh temperature control capability over 100 K mW^(-1).Moreover,an ultra-fast cooling rate exceeding 2000 K s^(-1) and excellent reliability of up to 1 million cycles are observed.Our proposed on-chip temperature controller is expected to enable further miniaturization and multifunctional integration on a single chip for microelectronics.
基金supported by the National Natural Science Foundation of China(Grant Nos.41473090,41430644,11675098,41373098,41430644,and 21490585)
文摘The sheet size of a graphene oxide （GO） can greatly influence its electrical, optical, mechanical, electrochemical and catalytic property. It is a key challenge to how to control the sheet size during its preparation in different application fields. According to our previous theoretical calculations of the effect of temperature on the oxidation process of graphene, we use Hummers method to prepare GOs with different sheet sizes by simply controlling the temperature condition in the process of the oxidation reaction of potassium permanganate （KMnO4） with graphene and the dilution process with deionized water. The results detected by transmission electron microscopy （TEM） and atomic force microscopy （AFM） show that the average sizes of GO sheets prepared at different temperatures are about 1 μm and 7 μm respectively. The ultraviolet-visible spectroscopy （UV-vis） shows that lower temperature can lead to smaller oxidation degrees of GO and less oxygen functional groups on the surface. In addition, we prepare GO membranes to test their mechanical strengths by ultrasonic waves, and we find that the strengths of the GO membranes prepared under low temperatures are considerably higher than those prepared under high temperatures, showing the high mechanical strengths of larger GO sheets. Our experimental results testify our previous theoretical calculations. Compared with the traditional centrifugal separation and chemical cutting method, the preparation process of GO by temperature control is simple and low-cost and also enables large-size synthesis. These findings develop a new method to control GO sheet sizes for large-scale potential applications.
文摘A neural adaptive proportion sum differential (PSD) algorithm with errors prediction is researched. It is applied in inertial navigation system(INS) temperature control. The algorithm do not need the process's precise mathematical model and can adapt to the process parameters changing, and can deal with the process with nonlinearity. According to the Smith predictor, author developed a method that takes the predicted process error and error change as neural adaptive PSD algorithm's input. The method is effective to the system with long dead time. The results of compute simulation show that this system has characters of quickly reaction, low overshoot and good stability. It can meet the requirements of temperature control of INS.
基金National Key R&D Plan Project(No.2021YFC3090102)。
文摘Temperature control curve is the key to achieving temperature control and crack prevention of high concrete dam during construction,and its rationality depends on the accurate measurement of temperature stress.With the simulation testing machine for the temperature stress,in the present study,we carried out the deformation process tests of concrete under three temperature curves:convex,straight and concave.Besides,we not only measured the early-age elastic modulus,creep parameters and stress process,but also proposed the preferred type.The results show that at early age,higher temperature always leads to greater elastic modulus and smaller creep.However,the traditional indoor experiments have underestimated the elastic modulus and creep development at early age,which makes the calculated value of temperature stress too small,thus increasing the cracking risk.In this study,the stress values of the three curves calculated based on the strain and early-age parameters are in good agreement with the temperature stress measured by the temperature stress testing machine,which verifies the method accuracy.When the temperature changes along the concave curve,the law of stress development is in consistent with that of strength.Under this condition,the stress fluctuation is small and the crack prevention safety of the concave type is higher,so the concave type is better.The test results provide a reliable basis and support for temperature control curve design and optimization of concrete dams.
文摘A new intelligent temperature control system for stove was introduced. It could accomplish A/D conversion, data processing, output displaying and alarming while the temperature exceeds the given threshold. The temperature adjusting devices were bi direction SCR and heating resistor. The hardware and software were discussed in the paper.
基金Supported by The National Natural Science Foundation of China (No. 59835170).
文摘Considering some characteristics of large-scale standing quench furnace, such as great heat inertia, evident time lag, strong coupling influence, hard to establish exact mathematical models of plant and etc, an artificial intelligent fuzzy control algorithm is put forward in this paper. Through adjusting the on-off ratio of electric heating elements, the temperature in furnace is controlled accurately. This paper describes structure and qualities of the large-scale standing quench furnace briefly, introduces constitution of control system, and expounds principle and implementation of intelligent control algorithm. The applied results prove that the intelligent control system can completely satisfy the technological requirements. Namely, it can realize fast increasing temperature with a little overshoot, exact holding temperature, and well-distributed temperature in quench furnace. It has raised the output and quality of aluminum material, and brought the outstanding economic and social benefits.
文摘A structure of central air conditioning system in building and its running pattern are proposed in order to perform optimum energy saving strategy. The design of room temperature controller is taken as an example to discuss the design of fuzzy controller using common microprogrammed control unit (MCU) in detail. Based on fuzzy theory the query control tables fixed in read only memory (ROM) of MCU are established to realize the energy saving in the room temperature controller and the reasoning procedure is analyzed. The diagram of hardware design and the flow chart of software of room temperature controller are presented. The results show that the proposed method is practical and effective to achieve the energy saving goal.
基金Supported by the National Natural Science Foundation of China (10978017)the Open Fund of Key Laboratory of Time and Frequency Primary Standards (CAS)+2 种基金the Postdoctoral Grant of China (94469)the Basic and Advanced Technology Research Foundation of Hennan Province (122300410169)the Fundamental Research Funds for the Central Universities
文摘Combining oven controlled technique,digital compensation,high-resolution frequency difference measurement and self-calibration technique,a new design method of precise oven controlled crystal oscillator（OCXO） is proposed.Fine compensation is made in the vicinity of the crystal temperature inflection point by using the non-real-time temperature compensation strategy,and self-calibration system is integrated in the crystal.The method improves the digital compensated phase noise,simplifies the traditional OCXO development system,reduces the cost and shortens the developing cycle.Experiment results show that with a standard reference signal and self-calibration updated data,the oscillator can work stable and achieve its best performence.The performance index of crystal oscillator had an improvement with one to two orders of magnitude on the basis of original technical index.The method is widely used in the improvement of high-end crystal oscillator and atomic clock.
基金supported by the Key Basic Research and Development Program(973)(No.2014CB046501)the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘Prepreg stickiness is the adhesion between prepregs or between a prepreg and a mold in lay-up process.It is critical for automated fiber placement,because the stickiness should be small for smooth transport,as well as large enough on the laying surface for a good placement performance.To ensure prepreg stickiness always being in the optimum laying window,placement temperature should be changed according to the laying speed.In our work,the relationship between laying speed and emissive power of heating lamp was studied.The heat transfer process between heating lamp and laying surface was analyzed and the control equation of dynamic temperature was derived.Finally,the infrared heating system was built and its effectiveness was verified based on placement experiment.
基金funding support of the National Key Research and Development Program of China(Grant No.2018YFA0702100)the National Natural Science Foundation of China(Grant No.52172259)。
文摘Thermoelectric devices(TEDs),including thermoelectric generators(TEGs) and thermoelectric coolers(TECs) based on the Seebeck and Peltier effects,respectively,are capable of converting heat directly into electricity and vice versa.Tough suffering from low energy conversion efficiency and relatively high capital cost,TEDs have found niche applications,such as the remote power source for spacecraft,solid-state refrigerators,waste heat recycling,and so on.In particular,onchip integrable micro thermoelectric devices(μ-TEDs),which can realize local thermal management,on-site temperature sensing,and energy harvesting under minor temperature gradient,could play an important role in biological sensing and cell cultivation,self-powered Internet of Things(IoT),and wearable electronics.In this review,starting from the basic principles of thermoelectric devices,we summarize the most critical parameters for μ-TEDs,design guidelines,and most recent advances in the fabrication process.In addition,some innovative applications of μ-TEDs,such as in combination with microfluidics and photonics,are demonstrated in detail.
基金supported by the National Natural Science Foundation of China(Grant Nos.51322603,51136001,and 51356001)the Program for New Century Excellent Talents in University,Science Fund for Creative Research Groups of China(Grant No.51321002)the Initiative Scientific Research Program of Tsinghua University,China
文摘Heat conduction in single-walled carbon nanotubes （SWCNTs） has been investigated by using various methods, while less work has been focused on multi-walled carbon nanotubes （MWCNTs）. The thermal conductivities of the double-walled carbon nanotubes （DWCNTs） with two different temperature control methods are studied by using molecular dynamics （MD） simulations. One case is that the heat baths （HBs） are imposed only on the outer wall, while the other is that the HBs are imposed on both the two walls. The results show that the ratio of the thermal conductivity of DWCNTs in the first case to that in the second case is inversely proportional to the ratio of the cross-sectional area of the DWCNT to that of its outer wall. In order to interpret the results and explore the heat conduction mechanisms, the inter-wall thermal transport of DWCNTs is simulated. Analyses of the temperature profiles of a DWCNT and its two walls in the two cases and the inter- wall thermal resistance show that in the first case heat is almost transported only along the outer wall, while in the second case a DWCNT behaves like parallel heat transport channels in which heat is transported along each wall independently. This gives a good explanation of our results and presents the heat conduction mechanisms of MWCNTs.
