This study investigates the paradoxical detonation behavior of TKX-50,a nitrogen-rich energetic material,exhibiting higher detonation velocities but lower metal acceleration ability compared to HMX.Through experimenta...This study investigates the paradoxical detonation behavior of TKX-50,a nitrogen-rich energetic material,exhibiting higher detonation velocities but lower metal acceleration ability compared to HMX.Through experimental measurements and theoretical calculations,we propose a novel three-factor competition mechanism to explain this phenomenon.TKX-50-based PBX formulations achieved detonation velocities up to 9100 m/s,surpassing HMX-based counterparts.However,cylinder expansion tests revealed a 15%reduction in metal acceleration ability.Thermochemical measurements showed lower detonation heat for TKX-50(4900 J/g)versus HMX(5645 J/g).Our mechanism involves:(1)compositional effects prevailing at high pressures;(2)Energy release becoming essential as pressure drops;(3)Pressure-dependent product composition evolution functioning at low pressure.VLW code calculations unveiled a"crossover"in Hugoniot curves,lending support to this mechanism.This study furnishes a new framework for comprehending the performance of nitrogen-rich energetic materials,with significant implications for the design and optimization of future high-energy density materials.展开更多
The acceleration of a high maneuvering target in signal processing is helpful to enhance the performance of the tracker and facilitate the classification of targets. At present, most of the research on acceleration es...The acceleration of a high maneuvering target in signal processing is helpful to enhance the performance of the tracker and facilitate the classification of targets. At present, most of the research on acceleration estimation is carried out in cases of a single target with time-frequency analysis methods such as fractional Fourier transform （FRFT）, Hough-ambiguity transform （HAT）, and Wigner-Vil e distribution （WVD）, which need to satisfy enough time duration and sampling theorem. Only one reference proposed a method of acceleration estimation for multiple targets based on modified polynomial phase transform （MPPT） in the lin-ear frequency modulation （LFM） continuous-wave （CW） radar. The method of acceleration estimation for multiple targets in the pulse Doppler （PD） radar has not been reported so far. Compressive sensing （CS） has the advantage of sampling at a low rate and short duration without sacrificing estimation performance. There-fore, this paper proposes a new method of acceleration estimation for multiple maneuvering targets with the unknown number based on CS with pulse Doppler signals. Simulation results validate the effectiveness of the proposed method under several conditions with different duration, measurement numbers, signal to noise ra-tios （SNR）, and regularization parameters, respectively. Simulation results also show that the performance of the proposed method is superior to that of FRFT and HAT in the condition of multiple targets.展开更多
Aiming at the problem of gliding near space hypersonic vehicle(NSHV)trajectory prediction,a trajectory prediction method based on aerodynamic acceleration empirical mode decomposition(EMD)is proposed.The method analyz...Aiming at the problem of gliding near space hypersonic vehicle(NSHV)trajectory prediction,a trajectory prediction method based on aerodynamic acceleration empirical mode decomposition(EMD)is proposed.The method analyzes the motion characteristics of the skipping gliding NSHV and verifies that the aerodynamic acceleration of the target has a relatively stable rule.On this basis,EMD is used to extract the trend of aerodynamic acceleration into multiple sub-items,and aggregate sub-items with similar attributes.Then,a prior basis function is set according to the aerodynamic acceleration stability rule,and the aggregated data are fitted by the basis function to predict its future state.After that,the prediction data of the aerodynamic acceleration are used to drive the system to predict the target trajectory.Finally,experiments verify the effectiveness of the method.In addition,the distribution of prediction errors in space is discussed,and the reasons are analyzed.展开更多
Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al wit...Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.展开更多
Respiratory monitoring is increasingly used in clinical and healthcare practices to diagnose chronic cardio-pulmonary functional diseases during various routine activities.Wearable medical devices have realized the po...Respiratory monitoring is increasingly used in clinical and healthcare practices to diagnose chronic cardio-pulmonary functional diseases during various routine activities.Wearable medical devices have realized the possibilities of ubiquitous respiratory monitoring,however,relatively little attention is paid to accuracy and reliability.In previous study,a wearable respiration biofeedback system was designed.In this work,three kinds of signals were mixed to extract respiratory rate,i.e.,respiration inductive plethysmography(RIP),3D-acceleration and ECG.In-situ experiments with twelve subjects indicate that the method significantly improves the accuracy and reliability over a dynamic range of respiration rate.It is possible to derive respiration rate from three signals within mean absolute percentage error 4.37%of a reference gold standard.Similarly studies derive respiratory rate from single-lead ECG within mean absolute percentage error 17%of a reference gold standard.展开更多
It has been said that,once a bomb casing has fractured, "detonation gases will then stream around the fragments or bypass them,and the acceleration process stops there." However,while apparently copious gas ...It has been said that,once a bomb casing has fractured, "detonation gases will then stream around the fragments or bypass them,and the acceleration process stops there." However,while apparently copious gas flow through casing fractures indicates some pressure release,it is also an indication of significant gas drive pressure,post casing fracture.This paper shows two approaches to the problem of calculating the actual loss of drive.One presents first-order analytical calculations,in cylindrical geometry,of pressure loss to the inside surface of a fractured casing.The second shows the modelling of a selected example in the CTH code.Both approaches reveal that gas escape,while occurring at its own soundspeed relative to the adjacent casing fragments,has to compete with rapid radial expansion of the casing.Together with some historic experiments now publicly available,our calculations indicate that post-fracture casing fragment acceleration is,for most systems,unlikely to be reduced significantly.展开更多
In recent years,heavy ion accelerator technology has been rapidly developing worldwide and widely applied in the fields of space radiation simulation and particle therapy.Usually,a very high uniformity in the irradiat...In recent years,heavy ion accelerator technology has been rapidly developing worldwide and widely applied in the fields of space radiation simulation and particle therapy.Usually,a very high uniformity in the irradiation area is required for the extracted ion beams,which is crucial because it directly affects the experimental precision and therapeutic effect.Specifically,ultra-large-area and high-uniformity scanning are crucial requirements for spacecraft radiation effects assessment and serve as core specification for beamline terminal design.In the 300 MeV proton and heavy ion accelerator complex at the Space Environment Simulation and Research Infrastructure(SESRI),proton and heavy ion beams will be accelerated and ultimately delivered to three irradiation terminals.In order to achieve the required large irradiation area of 320 mm×320 mm,horizontal and vertical scanning magnets are used in the extraction beam line.However,considering the various requirements for beam species and energies,the tracking accuracy of power supplies(PSs),the eddy current effect of scanning magnets,and the fluctuation of ion bunch structure will reduce the irradiation uniformity.To mitigate these effects,a beam uniformity optimization method based on the measured beam distribution was proposed and applied in the accelerator complex at SESRI.In the experiment,the uniformity is successfully optimized from 75%to over 90%after five iterations of adjustment to the PS waveforms.In this paper,the method and experimental results were introduced.展开更多
在这篇论文，一个概括加速反馈控制(声频抗流圈) 设计方法，命名声频抗流圈提高了 H ∞控制器，为两个被建议完整激活并且在激活的非线性的自治车辆系统下面。声频抗流圈基于已知的动力学作为柔韧的改进被设计到正常控制。首先，以便拒...在这篇论文，一个概括加速反馈控制(声频抗流圈) 设计方法，命名声频抗流圈提高了 H ∞控制器，为两个被建议完整激活并且在激活的非线性的自治车辆系统下面。声频抗流圈基于已知的动力学作为柔韧的改进被设计到正常控制。首先，以便拒绝不确定性和外部骚乱，线性 prefilter 在新声频抗流圈设计方法被使用在正常声频抗流圈代替高获得。然后，背走算法被用于 AFC 设计在激活的系统下面。两个的分析在有限获得 L2 稳定性显示出的频率领域和输入产量的骚乱变细新控制器设计方法是适用的。最后，模拟关于无人的模型直升飞机的追踪的控制被进行。结果与没有声频抗流圈，追踪的控制获得验证新方法的可行性的那些相比。展开更多
Intentional electromagnetic interference is a serious threat to the safety of electronic devices. Multiple electromagnetic pulses will be coupled and transmitted to electronic devices through the cables.Accumulative e...Intentional electromagnetic interference is a serious threat to the safety of electronic devices. Multiple electromagnetic pulses will be coupled and transmitted to electronic devices through the cables.Accumulative effects are generated, which make it easier for damage to occur in the electronic devices. In this article, the working principle of micro-silicon acceleration sensors is introduced. The accumulative effects of multiple pulses on acceleration sensors is studied by a large number of injection experiments.The accumulation trends of multiple pulses with different pulse numbers and intervals are analyzed. The damaged structures inside abnormal sensor amplifiers were observed via optical microscopy and scanning electron microscopy. The experimental results show that the accumulative effect is strengthened with increased pulse number or decreased pulse interval, and the threshold voltage for multiple pulses on the acceleration sensor decreases. The threshold voltage for a single pulse is 321.57 V. When the pulse interval is 1 μs and the pulse number is 5, the threshold voltage for multiple pulses is 163.42 V,which is reduced by 49.12% compared with a single pulse. These results provide a reference for the damage design of electromagnetic pulse weapons.展开更多
To find the distribution patterns of dynamic amplification coefficients for dams subjected to earthquake, 3D seismic responses of concrete-faced rockfill dams with different heights and different shapes of river valle...To find the distribution patterns of dynamic amplification coefficients for dams subjected to earthquake, 3D seismic responses of concrete-faced rockfill dams with different heights and different shapes of river valley were analyzed by using the equivalent-linear model. Statistical analysis was also made to the seismic coefficient, and an empirical formula for calculating the maximum acceleration was provided. The results indicate that under the condition of the same dam height and the same base acceleration excitations, with the increase of the river valley width, the position of the maximum acceleration on the axis of the top of the dam moves from the center to the riversides symmetrically. For the narrow valleys, the maximum acceleration occurs in the middle of the axis at the top of the dam; for wide valleys the maximum acceleration appears near the riversides. The result negates the application of 2D dynamical computation for wide valleys, and shows that for the seismic response of high concrete-faced rockfill dams, the seismic coefficient along the axis should be given, except for that along the dam height. Seismic stability analysis of rockfill dams using pseudo-static method can be modified according to the formula.展开更多
Many analytical methods have been adopted to estimate the slope stability by providing various stability numbers,e.g.static safety of factor(static FoS)or the critical seismic acceleration coefficient,while little att...Many analytical methods have been adopted to estimate the slope stability by providing various stability numbers,e.g.static safety of factor(static FoS)or the critical seismic acceleration coefficient,while little attention has been given to the relationship between the slope stability numbers and the critical seismic acceleration coefficient.This study aims to investigate the relationship between the static FoS and the critical seismic acceleration coefficient of soil slopes in the framework of the upper-bound limit analysis.Based on the 3D rotational failure mechanism,the critical seismic acceleration coefficient using the pseudo-static method and the static FoS using the strength reduction technique are first determined.Then,the relationship between the static FoS and the critical seismic acceleration coefficient is presented under considering the slope angleβ,the frictional angleφ,and the dimensionless coefficients B/H and c/γH.Finally,a fitting formula between the static FoS and the critical seismic acceleration coefficient is proposed and validated by analytical and numerical results.展开更多
基金support provided by the National Natural Science Foundation of China(Grant No.12102405)the Presidential Foundation of CAEP(Grant No.YZJJZQ2023008).
文摘This study investigates the paradoxical detonation behavior of TKX-50,a nitrogen-rich energetic material,exhibiting higher detonation velocities but lower metal acceleration ability compared to HMX.Through experimental measurements and theoretical calculations,we propose a novel three-factor competition mechanism to explain this phenomenon.TKX-50-based PBX formulations achieved detonation velocities up to 9100 m/s,surpassing HMX-based counterparts.However,cylinder expansion tests revealed a 15%reduction in metal acceleration ability.Thermochemical measurements showed lower detonation heat for TKX-50(4900 J/g)versus HMX(5645 J/g).Our mechanism involves:(1)compositional effects prevailing at high pressures;(2)Energy release becoming essential as pressure drops;(3)Pressure-dependent product composition evolution functioning at low pressure.VLW code calculations unveiled a"crossover"in Hugoniot curves,lending support to this mechanism.This study furnishes a new framework for comprehending the performance of nitrogen-rich energetic materials,with significant implications for the design and optimization of future high-energy density materials.
基金supported by the National Natural Science Foundation of China(6110216561102167)
文摘The acceleration of a high maneuvering target in signal processing is helpful to enhance the performance of the tracker and facilitate the classification of targets. At present, most of the research on acceleration estimation is carried out in cases of a single target with time-frequency analysis methods such as fractional Fourier transform （FRFT）, Hough-ambiguity transform （HAT）, and Wigner-Vil e distribution （WVD）, which need to satisfy enough time duration and sampling theorem. Only one reference proposed a method of acceleration estimation for multiple targets based on modified polynomial phase transform （MPPT） in the lin-ear frequency modulation （LFM） continuous-wave （CW） radar. The method of acceleration estimation for multiple targets in the pulse Doppler （PD） radar has not been reported so far. Compressive sensing （CS） has the advantage of sampling at a low rate and short duration without sacrificing estimation performance. There-fore, this paper proposes a new method of acceleration estimation for multiple maneuvering targets with the unknown number based on CS with pulse Doppler signals. Simulation results validate the effectiveness of the proposed method under several conditions with different duration, measurement numbers, signal to noise ra-tios （SNR）, and regularization parameters, respectively. Simulation results also show that the performance of the proposed method is superior to that of FRFT and HAT in the condition of multiple targets.
基金supported by the National High-Tech R&D Program of China(2015AA70560452015AA8017032P)the Postgraduate Funding Project(JW2018A039)。
文摘Aiming at the problem of gliding near space hypersonic vehicle(NSHV)trajectory prediction,a trajectory prediction method based on aerodynamic acceleration empirical mode decomposition(EMD)is proposed.The method analyzes the motion characteristics of the skipping gliding NSHV and verifies that the aerodynamic acceleration of the target has a relatively stable rule.On this basis,EMD is used to extract the trend of aerodynamic acceleration into multiple sub-items,and aggregate sub-items with similar attributes.Then,a prior basis function is set according to the aerodynamic acceleration stability rule,and the aggregated data are fitted by the basis function to predict its future state.After that,the prediction data of the aerodynamic acceleration are used to drive the system to predict the target trajectory.Finally,experiments verify the effectiveness of the method.In addition,the distribution of prediction errors in space is discussed,and the reasons are analyzed.
基金The authors would like to acknowledge National Natural Science Foundation of China(Grant No.11832006)Open Project of State Key Laboratory of Explosion Science and Technology in Beijing Institute of Technology(Grant No.KFJJ20-04 M)to provide fund for conducting experiments.
文摘Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.
基金Project(2012M510207)supported by the China Postdoctoral Science FoundationProjects(60932001,61072031)supported by the National Natural Science Foundation of China+2 种基金Project(2012AA02A604)supported by the National High Technology Research and Development Program of ChinaProject(2013ZX03005013)supported by the Next Generation Communication Technology Major Project of National Science and Technology,ChinaProject supported by the"One-hundred Talent"and the"Low-cost Healthcare"Programs of Chinese Academy of Sciences
文摘Respiratory monitoring is increasingly used in clinical and healthcare practices to diagnose chronic cardio-pulmonary functional diseases during various routine activities.Wearable medical devices have realized the possibilities of ubiquitous respiratory monitoring,however,relatively little attention is paid to accuracy and reliability.In previous study,a wearable respiration biofeedback system was designed.In this work,three kinds of signals were mixed to extract respiratory rate,i.e.,respiration inductive plethysmography(RIP),3D-acceleration and ECG.In-situ experiments with twelve subjects indicate that the method significantly improves the accuracy and reliability over a dynamic range of respiration rate.It is possible to derive respiration rate from three signals within mean absolute percentage error 4.37%of a reference gold standard.Similarly studies derive respiratory rate from single-lead ECG within mean absolute percentage error 17%of a reference gold standard.
基金sponsored by the NWIPT Department of the U.K.Ministry of Defence
文摘It has been said that,once a bomb casing has fractured, "detonation gases will then stream around the fragments or bypass them,and the acceleration process stops there." However,while apparently copious gas flow through casing fractures indicates some pressure release,it is also an indication of significant gas drive pressure,post casing fracture.This paper shows two approaches to the problem of calculating the actual loss of drive.One presents first-order analytical calculations,in cylindrical geometry,of pressure loss to the inside surface of a fractured casing.The second shows the modelling of a selected example in the CTH code.Both approaches reveal that gas escape,while occurring at its own soundspeed relative to the adjacent casing fragments,has to compete with rapid radial expansion of the casing.Together with some historic experiments now publicly available,our calculations indicate that post-fracture casing fragment acceleration is,for most systems,unlikely to be reduced significantly.
基金Supported by National Key R&D Program of China(2019YFA0405400)。
文摘In recent years,heavy ion accelerator technology has been rapidly developing worldwide and widely applied in the fields of space radiation simulation and particle therapy.Usually,a very high uniformity in the irradiation area is required for the extracted ion beams,which is crucial because it directly affects the experimental precision and therapeutic effect.Specifically,ultra-large-area and high-uniformity scanning are crucial requirements for spacecraft radiation effects assessment and serve as core specification for beamline terminal design.In the 300 MeV proton and heavy ion accelerator complex at the Space Environment Simulation and Research Infrastructure(SESRI),proton and heavy ion beams will be accelerated and ultimately delivered to three irradiation terminals.In order to achieve the required large irradiation area of 320 mm×320 mm,horizontal and vertical scanning magnets are used in the extraction beam line.However,considering the various requirements for beam species and energies,the tracking accuracy of power supplies(PSs),the eddy current effect of scanning magnets,and the fluctuation of ion bunch structure will reduce the irradiation uniformity.To mitigate these effects,a beam uniformity optimization method based on the measured beam distribution was proposed and applied in the accelerator complex at SESRI.In the experiment,the uniformity is successfully optimized from 75%to over 90%after five iterations of adjustment to the PS waveforms.In this paper,the method and experimental results were introduced.
文摘在这篇论文，一个概括加速反馈控制(声频抗流圈) 设计方法，命名声频抗流圈提高了 H ∞控制器，为两个被建议完整激活并且在激活的非线性的自治车辆系统下面。声频抗流圈基于已知的动力学作为柔韧的改进被设计到正常控制。首先，以便拒绝不确定性和外部骚乱，线性 prefilter 在新声频抗流圈设计方法被使用在正常声频抗流圈代替高获得。然后，背走算法被用于 AFC 设计在激活的系统下面。两个的分析在有限获得 L2 稳定性显示出的频率领域和输入产量的骚乱变细新控制器设计方法是适用的。最后，模拟关于无人的模型直升飞机的追踪的控制被进行。结果与没有声频抗流圈，追踪的控制获得验证新方法的可行性的那些相比。
基金funded by the National Natural Science Foundation of China(Grant No.11502118).
文摘Intentional electromagnetic interference is a serious threat to the safety of electronic devices. Multiple electromagnetic pulses will be coupled and transmitted to electronic devices through the cables.Accumulative effects are generated, which make it easier for damage to occur in the electronic devices. In this article, the working principle of micro-silicon acceleration sensors is introduced. The accumulative effects of multiple pulses on acceleration sensors is studied by a large number of injection experiments.The accumulation trends of multiple pulses with different pulse numbers and intervals are analyzed. The damaged structures inside abnormal sensor amplifiers were observed via optical microscopy and scanning electron microscopy. The experimental results show that the accumulative effect is strengthened with increased pulse number or decreased pulse interval, and the threshold voltage for multiple pulses on the acceleration sensor decreases. The threshold voltage for a single pulse is 321.57 V. When the pulse interval is 1 μs and the pulse number is 5, the threshold voltage for multiple pulses is 163.42 V,which is reduced by 49.12% compared with a single pulse. These results provide a reference for the damage design of electromagnetic pulse weapons.
基金Project(90815024) supported by the National Natural Science Foundation of China
文摘To find the distribution patterns of dynamic amplification coefficients for dams subjected to earthquake, 3D seismic responses of concrete-faced rockfill dams with different heights and different shapes of river valley were analyzed by using the equivalent-linear model. Statistical analysis was also made to the seismic coefficient, and an empirical formula for calculating the maximum acceleration was provided. The results indicate that under the condition of the same dam height and the same base acceleration excitations, with the increase of the river valley width, the position of the maximum acceleration on the axis of the top of the dam moves from the center to the riversides symmetrically. For the narrow valleys, the maximum acceleration occurs in the middle of the axis at the top of the dam; for wide valleys the maximum acceleration appears near the riversides. The result negates the application of 2D dynamical computation for wide valleys, and shows that for the seismic response of high concrete-faced rockfill dams, the seismic coefficient along the axis should be given, except for that along the dam height. Seismic stability analysis of rockfill dams using pseudo-static method can be modified according to the formula.
基金Project(2017YFB1201204)supported by the National Key R&D Program of ChinaProject(1053320190957)supported by the Fundamental Research Funds for the Central Universities,China。
文摘Many analytical methods have been adopted to estimate the slope stability by providing various stability numbers,e.g.static safety of factor(static FoS)or the critical seismic acceleration coefficient,while little attention has been given to the relationship between the slope stability numbers and the critical seismic acceleration coefficient.This study aims to investigate the relationship between the static FoS and the critical seismic acceleration coefficient of soil slopes in the framework of the upper-bound limit analysis.Based on the 3D rotational failure mechanism,the critical seismic acceleration coefficient using the pseudo-static method and the static FoS using the strength reduction technique are first determined.Then,the relationship between the static FoS and the critical seismic acceleration coefficient is presented under considering the slope angleβ,the frictional angleφ,and the dimensionless coefficients B/H and c/γH.Finally,a fitting formula between the static FoS and the critical seismic acceleration coefficient is proposed and validated by analytical and numerical results.
