In this study,samples obtained from 1.3343 high-speed steel punches with TiN coatings were tested.The samples were subjected to heat treatment at different cryogenic temperatures(<196℃)and durations(12,24 and 36 h...In this study,samples obtained from 1.3343 high-speed steel punches with TiN coatings were tested.The samples were subjected to heat treatment at different cryogenic temperatures(<196℃)and durations(12,24 and 36 h),followed by tempering at two different temperatures(200,500℃).For performance testing,a ball-on-disk wear test setup was utilized and a total of 6 groups of samples were examined.The effects of cryo-treatment and tempering on microstructure were revealed through microstructural analysis with scanning electron microscopy(SEM),X-ray(XRD diffraction),and Rietveld analysis.Additionally,the hardness of the punches was measured with microhardness measurements.The optimal wear resistance was observed in the 36 h deep cryo-treated and 200℃tempered samples.The characterization study indicates that by cryogenic treatment a significant portion of the retained austenite transformed into martensite and secondary carbides formed,resulting in improved wear resistance and a slight increase in hardness.展开更多
In the present study,the mechanical and ballistic properties of friction stir welded(FSW)aluminum alloy(AA5754)samples were investigated,both untreated and cryogenically treated,when impacted by a 7.62 mm armour-pierc...In the present study,the mechanical and ballistic properties of friction stir welded(FSW)aluminum alloy(AA5754)samples were investigated,both untreated and cryogenically treated,when impacted by a 7.62 mm armour-piercing(AP)bullet at an impact velocity of 682±20 m/s.The FSW technique was used to prepare the welded samples for AA5754,with an axial force of 7 kN,a feed rate of 20 mm/min,and a speed of 1200 rpm.The cryogenic treatments performed after welding,including deep cryogenic treatment(DCT)at196℃ and shallow cryogenic treatment(SCT)at80℃,for 6 and 72 h,respectively.The microstructure and mechanical characteristics of cryogenically treated and untreated joints were examined.The cryogenic treatment refined the grain size(1.05 μm)and enhanced the microhardness(93 Hv).Moreover,DCT-FSW significantly improved the tensile strength(13.93%)and impact strength(8.45%)compared to untreated FSW sample.Additionally,in untreated FSW samples,the fracture behaviour varied:the impact fracture mode primarily exhibited ductile failure,while the tensile fracture exhibited a mixed fracture mode.In contrast,the tensile and impact fracture modes of the DCT-FSWwere dominated by a ductile failure mode.The DCT-FSW target demonstrated a lower depth of penetration(DOP)of 31 mm compared to the SCT-FSWand untreated FSW targets.Post-ballistic SEM analysis in the crater region of all three zones revealed the formation of frictional grooves,small cracks,and adiabatic shear bands(ASBs).展开更多
The evaporative cooling,which assists the refrigeration machinery air-conditioning systems test-rig,has been designed.Its structure and working principle were described,and the performance test was conducted and analy...The evaporative cooling,which assists the refrigeration machinery air-conditioning systems test-rig,has been designed.Its structure and working principle were described,and the performance test was conducted and analyzed.The test shows that making full use of the evaporative cooling "free cooling" in Spring and Autumn seasons can fully meet the requirements of air-conditioned comfort through the switch of the function in different seasons.Taking into account the evaporative cooling fan and pump energy consumption,compared with the traditional mechanical refrigeration system,more than 80 percent of energy can be saved,and the energy efficiency ratio of the Unit(EER)is as high as 7.63.Using the two stages of indirect evaporative cooling to pre-cool the new wind in summer,under the conditions of the same air supply temperature requirements,0.83 kg/s chilled water saved can be equivalent to the traditional mechanical refrigeration system,and when the new wind ratio up to 50 percent,more than 10 percent load was reduced in mechanical refrigeration system.The overall EER increased about 35 percent.展开更多
Common insulation gas cannot normally work in refrigeration temperature range(153-243 K), especially in extremely cold regions. To solve this problem, this essay uses cubic equation combined with two-parameter model i...Common insulation gas cannot normally work in refrigeration temperature range(153-243 K), especially in extremely cold regions. To solve this problem, this essay uses cubic equation combined with two-parameter model in theorem of corresponding states to estimate dew-point of hybrid gas. The influence of temperature on mixing ratio is studied by using van der Waals equation. The result shows that the mixing ratio is stable during temperature-fall period. Insulation property of CF_4 and CF_4/N_2 in refrigeration temperature range is studied through self-designed low-temperature test system. The result shows when the density of hybrid gas is invariable, temperature changing has less influence on breakdown voltage, and when the mixing ratio is 20%, CF_4/N_2 is the greatest potential hybrid gas.展开更多
A model of quantum thermoacoustic refrigeration micro-cycle(QTARMC)is established in which heat leakage is considered.A single particle contained in a one-dimensional harmonic potential well is studied,and the system ...A model of quantum thermoacoustic refrigeration micro-cycle(QTARMC)is established in which heat leakage is considered.A single particle contained in a one-dimensional harmonic potential well is studied,and the system consists of countless replicas.Each particle is confined in its own potential well,whose occupation probabilities can be expressed by the thermal equilibrium Gibbs distributions.Based on the Schrodinger equation,the expressions of coefficient of performance(COP)and cooling rate for the refrigerator are obtained.Effects of heat leakage on the optimal performance are discussed.The optimal performance region of the refrigeration cycle is obtained by the using ofΩobjective function.The results obtained can enrich the thermoacoustic theory and expand the application of quantum thermodynamics.展开更多
Some magnetocaloric materials were used successfully in magnetic refrigeration application and became one of the critical parts of magnetic refrigeration technology whose delightful progresses were made worldwide in t...Some magnetocaloric materials were used successfully in magnetic refrigeration application and became one of the critical parts of magnetic refrigeration technology whose delightful progresses were made worldwide in the past 30 years. At the same time, the research on giant magnetocaloric materials will accelerate the development of room temperature magnetic refrigeration. In this paper, the new theoretical and experimental investigations on magnetic materials in room temperature application were described, including Gd and its binary and ternary intermetallic compounds, Mn-based compounds, La(Fe13-xMx)-based compounds and manganites. Based on the analysis of hysteresis, corrosion, cost and heat process, the comparison between different families of magnetic materials was discussed. Further research of room temperature magnetic refrigerant was suggested.展开更多
The mechanism of gas discharge in refrigeration temperature range is still not clear. N2, CF4, 20% CF4＋N2 and 50%CF4＋50%N2 binary gas mixtures were tested under the conditions of –153–25 ℃ and 50–2000 Pa. The ex...The mechanism of gas discharge in refrigeration temperature range is still not clear. N2, CF4, 20% CF4＋N2 and 50%CF4＋50%N2 binary gas mixtures were tested under the conditions of –153–25 ℃ and 50–2000 Pa. The experimental results show that the minimum of Paschen curves of all test samples shifts to low pressure, from 500 Pa to 200 Pa. The value of Paschen curve minimum of N2 shows remarkable fluctuation. This fluctuation is explained by molecule agglomeration and electronic mean energy. The fluctuation decreases with the increasing mixing ratio of CF4. What’s more, the value of Paschen curve minimum of CF4 decreases with temperature. This phenomenon is ascribed to attach-radiation and secondary process.展开更多
基金Project supported by the Haier GroupProject supported by the Eskisehir Osmangazi University,Türkiye。
文摘In this study,samples obtained from 1.3343 high-speed steel punches with TiN coatings were tested.The samples were subjected to heat treatment at different cryogenic temperatures(<196℃)and durations(12,24 and 36 h),followed by tempering at two different temperatures(200,500℃).For performance testing,a ball-on-disk wear test setup was utilized and a total of 6 groups of samples were examined.The effects of cryo-treatment and tempering on microstructure were revealed through microstructural analysis with scanning electron microscopy(SEM),X-ray(XRD diffraction),and Rietveld analysis.Additionally,the hardness of the punches was measured with microhardness measurements.The optimal wear resistance was observed in the 36 h deep cryo-treated and 200℃tempered samples.The characterization study indicates that by cryogenic treatment a significant portion of the retained austenite transformed into martensite and secondary carbides formed,resulting in improved wear resistance and a slight increase in hardness.
文摘In the present study,the mechanical and ballistic properties of friction stir welded(FSW)aluminum alloy(AA5754)samples were investigated,both untreated and cryogenically treated,when impacted by a 7.62 mm armour-piercing(AP)bullet at an impact velocity of 682±20 m/s.The FSW technique was used to prepare the welded samples for AA5754,with an axial force of 7 kN,a feed rate of 20 mm/min,and a speed of 1200 rpm.The cryogenic treatments performed after welding,including deep cryogenic treatment(DCT)at196℃ and shallow cryogenic treatment(SCT)at80℃,for 6 and 72 h,respectively.The microstructure and mechanical characteristics of cryogenically treated and untreated joints were examined.The cryogenic treatment refined the grain size(1.05 μm)and enhanced the microhardness(93 Hv).Moreover,DCT-FSW significantly improved the tensile strength(13.93%)and impact strength(8.45%)compared to untreated FSW sample.Additionally,in untreated FSW samples,the fracture behaviour varied:the impact fracture mode primarily exhibited ductile failure,while the tensile fracture exhibited a mixed fracture mode.In contrast,the tensile and impact fracture modes of the DCT-FSWwere dominated by a ductile failure mode.The DCT-FSW target demonstrated a lower depth of penetration(DOP)of 31 mm compared to the SCT-FSWand untreated FSW targets.Post-ballistic SEM analysis in the crater region of all three zones revealed the formation of frictional grooves,small cracks,and adiabatic shear bands(ASBs).
基金Xi'an Polytechnic University Graduate Innovational Foundation(chx080608)
文摘The evaporative cooling,which assists the refrigeration machinery air-conditioning systems test-rig,has been designed.Its structure and working principle were described,and the performance test was conducted and analyzed.The test shows that making full use of the evaporative cooling "free cooling" in Spring and Autumn seasons can fully meet the requirements of air-conditioned comfort through the switch of the function in different seasons.Taking into account the evaporative cooling fan and pump energy consumption,compared with the traditional mechanical refrigeration system,more than 80 percent of energy can be saved,and the energy efficiency ratio of the Unit(EER)is as high as 7.63.Using the two stages of indirect evaporative cooling to pre-cool the new wind in summer,under the conditions of the same air supply temperature requirements,0.83 kg/s chilled water saved can be equivalent to the traditional mechanical refrigeration system,and when the new wind ratio up to 50 percent,more than 10 percent load was reduced in mechanical refrigeration system.The overall EER increased about 35 percent.
基金Project(51277063)supported by the National Natural Science Foundation of China
文摘Common insulation gas cannot normally work in refrigeration temperature range(153-243 K), especially in extremely cold regions. To solve this problem, this essay uses cubic equation combined with two-parameter model in theorem of corresponding states to estimate dew-point of hybrid gas. The influence of temperature on mixing ratio is studied by using van der Waals equation. The result shows that the mixing ratio is stable during temperature-fall period. Insulation property of CF_4 and CF_4/N_2 in refrigeration temperature range is studied through self-designed low-temperature test system. The result shows when the density of hybrid gas is invariable, temperature changing has less influence on breakdown voltage, and when the mixing ratio is 20%, CF_4/N_2 is the greatest potential hybrid gas.
基金Project(51176143)supported by the National Natural Science Foundation of ChinaProject(K201919)supported by the Scientific Research Foundation of Wuhan Institute of TechnologyChina。
文摘A model of quantum thermoacoustic refrigeration micro-cycle(QTARMC)is established in which heat leakage is considered.A single particle contained in a one-dimensional harmonic potential well is studied,and the system consists of countless replicas.Each particle is confined in its own potential well,whose occupation probabilities can be expressed by the thermal equilibrium Gibbs distributions.Based on the Schrodinger equation,the expressions of coefficient of performance(COP)and cooling rate for the refrigerator are obtained.Effects of heat leakage on the optimal performance are discussed.The optimal performance region of the refrigeration cycle is obtained by the using ofΩobjective function.The results obtained can enrich the thermoacoustic theory and expand the application of quantum thermodynamics.
基金Project(50876082) supported by the National Natural Science Foundation of ChinaProject(IRT0746) supported by the Changjiang Scholars and Innovative Research Team in University
文摘Some magnetocaloric materials were used successfully in magnetic refrigeration application and became one of the critical parts of magnetic refrigeration technology whose delightful progresses were made worldwide in the past 30 years. At the same time, the research on giant magnetocaloric materials will accelerate the development of room temperature magnetic refrigeration. In this paper, the new theoretical and experimental investigations on magnetic materials in room temperature application were described, including Gd and its binary and ternary intermetallic compounds, Mn-based compounds, La(Fe13-xMx)-based compounds and manganites. Based on the analysis of hysteresis, corrosion, cost and heat process, the comparison between different families of magnetic materials was discussed. Further research of room temperature magnetic refrigerant was suggested.
基金Project(51277063) supported by the National Natural Science Foundation of ChinaProject(51407013) supported in part by the National Natural Science Foundation of China
文摘The mechanism of gas discharge in refrigeration temperature range is still not clear. N2, CF4, 20% CF4＋N2 and 50%CF4＋50%N2 binary gas mixtures were tested under the conditions of –153–25 ℃ and 50–2000 Pa. The experimental results show that the minimum of Paschen curves of all test samples shifts to low pressure, from 500 Pa to 200 Pa. The value of Paschen curve minimum of N2 shows remarkable fluctuation. This fluctuation is explained by molecule agglomeration and electronic mean energy. The fluctuation decreases with the increasing mixing ratio of CF4. What’s more, the value of Paschen curve minimum of CF4 decreases with temperature. This phenomenon is ascribed to attach-radiation and secondary process.
