In order to address the current inability of screen printing to monitor printing pressure online,an online printing pressure monitoring system applied to screen printing machines was designed in this study.In this stu...In order to address the current inability of screen printing to monitor printing pressure online,an online printing pressure monitoring system applied to screen printing machines was designed in this study.In this study,the consistency of printed electrodes was measured by using a confocal microscope and the pressure distribution detected by online pressure monitoring system was compared to investigate the relationship.The results demonstrated the relationship between printing pressure and the consistency of printed electrodes.As printing pressure increases,the ink layer at the corresponding position becomes thicker and that higher printing pressure enhances the consistency of the printed electrodes.The experiment confirms the feasibility of the online pressure monitoring system,which aids in predicting and controlling the consistency of printed electrodes,thereby improving their performance.展开更多
3D printing technology enhances the combustion characteristics of hybrid rocket fuels by enabling complex geometries. However, improvements in regression rates and energy properties of monotonous 3D printed fuels have...3D printing technology enhances the combustion characteristics of hybrid rocket fuels by enabling complex geometries. However, improvements in regression rates and energy properties of monotonous 3D printed fuels have been limited. This study explores the impact of poly(vinylidene fluoride) and polydopamine-coated aluminum particles on the thermal and combustion properties of 3D printed hybrid rocket fuels. Physical self-assembly and anti-solvent methods were employed for constructing composite μAl particles. Characterization using SEM, XRD, XPS, FTIR, and μCT revealed a core-shell structure and homogeneous elemental distribution. Thermal analysis showed that PVDF coatings significantly increased the heat of combustion for aluminum particles, with maximum enhancement observed in μAl@PDA@PVDF(denoted as μAl@PF) at 6.20 k J/g. Subsequently, 3D printed fuels with varying pure and composite μAl particle contents were prepared using 3D printing. Combustion tests indicated higher regression rates for Al@PF/Resin composites compared to pure resin, positively correlating with particle content. The fluorocarbon-alumina reaction during the combustion stage intensified Al particle combustion, reducing residue size. A comprehensive model based on experiments provides insights into the combustion process of PDA and PVDF-coated droplets. This study advances the design of 3D-printed hybrid rocket fuels, offering strategies to improve regression rates and energy release, crucial for enhancing solid fuel performance for hybrid propulsion.展开更多
In order to study the preferred skin color for printing images,two CMYK images from ISO 400 and one from iStock,including five skin color images of East Asian females was selected in this study.The images were adjuste...In order to study the preferred skin color for printing images,two CMYK images from ISO 400 and one from iStock,including five skin color images of East Asian females was selected in this study.The images were adjusted with the CMYK printing ink volume variation of the single,double and triple channels in the given 280%total ink limit conditions.A larger number of color vision normal observers were organized to carry out the color preference evaluation experiment,and the selected preferred skin colors were analyzed.The distribution range of the chromaticity values for skin color images were obtained and the results indicated that there are three regions for printing skin color preferences,and the observers have a memory preference for brighter,fairer skin colors in young female and a reddish skin colors in girl,which can provide the guidance for color adjustment of printed skin color images.展开更多
In order to improve the quality of 3D printed raspberry preserves after post-processing,microwave ovens combining infrared and microwave methods were utilized.The effects of infrared heating temperature,infrared heati...In order to improve the quality of 3D printed raspberry preserves after post-processing,microwave ovens combining infrared and microwave methods were utilized.The effects of infrared heating temperature,infrared heating time,microwave power,microwave heating time on the center temperature,moisture content,the chroma(C*),the total color difference(ΔE*),shape fidelity,hardness,and the total anthocyanin content of 3D printed raspberry preserves were analyzed by response surface method(RSM).The results showed that under combining with the two methods,infrared heating improved the fidelity and quality degradation of printed products,while microwave heating enhanced the efficiency of infrared heating.Infrared-microwave combination cooking could maintain relatively stable color appearance and shape of 3D printed raspberry preserves.The AHP–CRITIC hybrid weighting method combined with the response surface test to determine the comprehensive weights of the evaluation indicators optimized the process parameters,and the optimal process parameters were obtained:infrared heating temperature of 190℃,infrared heating time of 10 min and 30 s,microwave power of 300 W,and microwave heating time of 2 min and 6 s.The 3D printed raspberry cooking methods obtained under the optimal conditions seldom had color variation,porous structure,uniform texture,and high shape fidelity,which retained the characteristics of personalized manufacturing by 3D printing.This study could provide a reference for the postprocessing and quality control of 3D cooking methods.展开更多
Additive Manufacturing(AM)can provide customized parts that conventional techniques fail to deliver.One important parameter in AM is the quality of the parts,as a result of the material extrusion 3D printing(3D-P)proc...Additive Manufacturing(AM)can provide customized parts that conventional techniques fail to deliver.One important parameter in AM is the quality of the parts,as a result of the material extrusion 3D printing(3D-P)procedure.This can be very important in defense-related applications,where optimum performance needs to be guaranteed.The quality of the Polyetherimide 3D-P specimens was examined by considering six control parameters,namely,infill percentage,layer height,deposition angle,travel speed,nozzle,and bed temperature.The quality indicators were the root mean square(Rq)and average(Ra)roughness,porosity,and the actual to nominal dimensional deviation.The examination was performed with optical profilometry,optical microscopy,and micro-computed tomography scanning.The Taguchi design of experiments was applied,with twenty-five runs,five levels for each control parameter,on five replicas.Two additional confirmation runs were conducted,to ensure reliability.Prediction equations were constructed to express the quality indicators in terms of the control parameters.Three modeling approaches were applied to the experimental data,to compare their efficiency,i.e.,Linear Regression Model(LRM),Reduced Quadratic Regression Model,and Quadratic Regression Model(QRM).QRM was the most accurate one,still the differences were not high even considering the simpler LRM model.展开更多
Due to their high hardness and high strength,VC reinforced hard materials such as high vanadium high-speed steel(HVHSS)are not suitable for machining to obtain complex shape with low cost.Therefore,3D gel printing(3DG...Due to their high hardness and high strength,VC reinforced hard materials such as high vanadium high-speed steel(HVHSS)are not suitable for machining to obtain complex shape with low cost.Therefore,3D gel printing(3DGP)was employed to print HVHSS parts,using highly loaded slurry with 60%solid content as printing slurry.After printing parameters optimization,the printing sample had good surface quality,and obvious printing lines were observed.The extruded filament was in-situ cured,thus enough to maintain the designed shape.Uniform sintering shrinkage with a shrinkage rate of about 15%was obtained in the as-sintered sample with relative density of 99%.The surface roughness decreased from 6.5μm to 3.8μm.Fine carbides(<1μm)and dense microstructure were achieved.Besides,the as-sintered sample had comprehensive performance of HRC60 in hardness,3000 MPa in bend strength,and 20−26 J in impact energy.This study proposed one promising method to directly manufacture complex-shaped hard materials without subsequent machining.展开更多
Rheological properties of microemulsions(MEs) and their printability in three dimensional printing(3DP) systems were investigated.A series of MEs with different contents of oil phase were prepared using sonication met...Rheological properties of microemulsions(MEs) and their printability in three dimensional printing(3DP) systems were investigated.A series of MEs with different contents of oil phase were prepared using sonication method with ibuprofen as model drug and soybean lecithin as emulfier.Stationary and transient rheological properties of MEs were investigated by ARES-SRF using concentric cylinders measuring systems.3DP systems with piezoelectric drop-on-demand print heads were employed to test the printability of the MEs.Results demonstrate that the apparent viscosity and dynamic linear viscoelastic regions of the MEs are the most important parameters for continuous and stable printing of MEs by 3DP.The incorporation of drug in the MEs has little influence on the MEs' stationary rheological behaviors and dynamic viscoelasticity,but the concentration of oil phase has a strong influence on them.The rheological property of binder liquids has a close relationship with their printability in 3DP system.展开更多
A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used t...A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.展开更多
Conventional exploding foil initiator (EFI) in ignition or detonation applications hosts many performance advantages, but was hindered by the bulky, inaccurate, inefficient and expensive shortcomings. We highlight a n...Conventional exploding foil initiator (EFI) in ignition or detonation applications hosts many performance advantages, but was hindered by the bulky, inaccurate, inefficient and expensive shortcomings. We highlight a novel micro-chip exploding foil initiator (McEFI) using printed circuit board (PCB) technology. The structural parameters were determined based on energy coupling relationship at the component interfaces. Next, the prototype McEFI has been batch-fabricated using PCB technology, with a monolithic structure of 7.0 mm (l) × 4.5 mm (w) × 4.0 mm (δ). As expected, this PCB-McEFI illustrated the successful firing validations for explosives pellets. This paper has addressed the cost problem in both military munitions and civil markets wherever reliable, insensitive and timing-dependent ignition or detonation are involved.展开更多
The crushing performance of printed circuit board (PCB) was studied on several crushers. The results show that PCB is a material which is difficult to crush. The crushing performance of PCB with disk crusher, especial...The crushing performance of printed circuit board (PCB) was studied on several crushers. The results show that PCB is a material which is difficult to crush. The crushing performance of PCB with disk crusher, especially vibration grinding, which has cut or impact action, excels that of jaw crusher or roller crusher. The PCB scrap is worthwhile to recycle using variety of modern characterization methods. When compared with natural resources, this material stream remains a rich precious metal and nonferrous metals. In PCB scrap, metals account for 47% of the total material composition, in which there exists 19.66% copper, 11.47% iron, 3.93% lead, 300 g/t gold and 510 kg/t silver, etc. In addition, the PCB scrap contains 27% of plastics and 26% of refractory oxides.展开更多
Thermal decomposition of waste epoxy PCBs was performed in different atmospheres （nitrogen, argon, air and vacuum） at a heating rate of 10 ℃/rain by DSC-TGA, and the pyrolysis characteristic was analyzed. The gases...Thermal decomposition of waste epoxy PCBs was performed in different atmospheres （nitrogen, argon, air and vacuum） at a heating rate of 10 ℃/rain by DSC-TGA, and the pyrolysis characteristic was analyzed. The gases volatilized from the experiment were qualitatively analyzed by TG-FTIR. Kinetics study shows that pyrolysis reaction takes place between 300 and 400℃, and the activation energies are 256, 212 and 186.2 kJ/mol in nitrogen, argon and vacuum, respectively. There are two mass-loss processes in the decomposition under air atmosphere. In the first mass-loss process, the decomposition is the main reaction, and in the second process, the oxidation is the main reaction. The activation energy of the second mass-loss process is 99.6 kJ/mol by isothermal heat-treatments. TG-FTIR analysis shows carbon dioxide, carbon monoxide, hydrogen bromide, phenol and substituent phenol are given off during the pyrolysis of waste epoxy PCBs.展开更多
Additive manufacturing(AM),also known as 3D-printing(3DP)technology,is an advanced manufacturing technology that has developed rapidly in the past 40 years.However,the ceramic material printing is still challenging be...Additive manufacturing(AM),also known as 3D-printing(3DP)technology,is an advanced manufacturing technology that has developed rapidly in the past 40 years.However,the ceramic material printing is still challenging because of the issue of cracking.Indirect 3D printing has been designed and drawn attention because of its high manufacturing speed and low cost.Indirect 3D printing separates the one-step forming process of direct 3D printing into binding and material sintering,avoiding the internal stress caused by rapid cooling,making it possible to realize the highquality ceramic component with complex shape.This paper presents the research progress of leading indirect 3D printing technologies,including binder jetting(BJ),stereolithography(SLA),and fused deposition modeling(FDM).At present,the additive manufacturing of ceramic materials is mainly achieved through indirect 3D printing technology,and these materials include silicon nitride,hydroxyapatite functional ceramics,silicon carbide structural ceramics.展开更多
Three-dimensional(3D)micro-jet printing is a droplet deposition technique based on liquid-phase materials.To improve the deposition density and performance of energetic films with micro/nanoscale on an energetic chip,...Three-dimensional(3D)micro-jet printing is a droplet deposition technique based on liquid-phase materials.To improve the deposition density and performance of energetic films with micro/nanoscale on an energetic chip,polydopamine(PDA)was utilized as a linker bridge to induce the in-situ self-assembly of CL-20-based energetic film via 3D micro-jet printing.The self-assembly was extensively characterized by confocal laser scanning microscopy(CLSM),SEM,power-XRD,XPS,and DSC.The performance of the self-assembled film was verified by the mechanical properties and detonation properties,and a possible self-assembly mechanism in the layer-by-layer micro-jet printing process was proposed.The results indicated PDA-induced self-assembly enhanced the physical entanglement between the binders and energetic crystal,reduced the porosity from 15.87%to 11.28%,and improved the elastic modulus and the detonation performance of the CL-20-based energetic film.This work proposes a novel and promising energetic film design and fabrication strategy to enhance the interaction between the energetic composite layers in the micro-jet printing process.展开更多
Introduction:3D bio-printing technology<sup>[1-3]</sup>（Figure 1）capable of dispensing live cells,soluble factors,and phase-changing hydrogel in a desired pattern,has great potential in creating 3D tissu...Introduction:3D bio-printing technology<sup>[1-3]</sup>（Figure 1）capable of dispensing live cells,soluble factors,and phase-changing hydrogel in a desired pattern,has great potential in creating 3D tissue.However,maintaining the viability of a thick tissue structure during tissue growth and maturation is challenging due to lack of adequate vascular perfusion.In a simple tissue model with展开更多
文摘In order to address the current inability of screen printing to monitor printing pressure online,an online printing pressure monitoring system applied to screen printing machines was designed in this study.In this study,the consistency of printed electrodes was measured by using a confocal microscope and the pressure distribution detected by online pressure monitoring system was compared to investigate the relationship.The results demonstrated the relationship between printing pressure and the consistency of printed electrodes.As printing pressure increases,the ink layer at the corresponding position becomes thicker and that higher printing pressure enhances the consistency of the printed electrodes.The experiment confirms the feasibility of the online pressure monitoring system,which aids in predicting and controlling the consistency of printed electrodes,thereby improving their performance.
基金funded by the National Natural Science Foundation of China(Grant No.06101213)the National Natural Science Foundation of China(Grant No.22105160).
文摘3D printing technology enhances the combustion characteristics of hybrid rocket fuels by enabling complex geometries. However, improvements in regression rates and energy properties of monotonous 3D printed fuels have been limited. This study explores the impact of poly(vinylidene fluoride) and polydopamine-coated aluminum particles on the thermal and combustion properties of 3D printed hybrid rocket fuels. Physical self-assembly and anti-solvent methods were employed for constructing composite μAl particles. Characterization using SEM, XRD, XPS, FTIR, and μCT revealed a core-shell structure and homogeneous elemental distribution. Thermal analysis showed that PVDF coatings significantly increased the heat of combustion for aluminum particles, with maximum enhancement observed in μAl@PDA@PVDF(denoted as μAl@PF) at 6.20 k J/g. Subsequently, 3D printed fuels with varying pure and composite μAl particle contents were prepared using 3D printing. Combustion tests indicated higher regression rates for Al@PF/Resin composites compared to pure resin, positively correlating with particle content. The fluorocarbon-alumina reaction during the combustion stage intensified Al particle combustion, reducing residue size. A comprehensive model based on experiments provides insights into the combustion process of PDA and PVDF-coated droplets. This study advances the design of 3D-printed hybrid rocket fuels, offering strategies to improve regression rates and energy release, crucial for enhancing solid fuel performance for hybrid propulsion.
文摘In order to study the preferred skin color for printing images,two CMYK images from ISO 400 and one from iStock,including five skin color images of East Asian females was selected in this study.The images were adjusted with the CMYK printing ink volume variation of the single,double and triple channels in the given 280%total ink limit conditions.A larger number of color vision normal observers were organized to carry out the color preference evaluation experiment,and the selected preferred skin colors were analyzed.The distribution range of the chromaticity values for skin color images were obtained and the results indicated that there are three regions for printing skin color preferences,and the observers have a memory preference for brighter,fairer skin colors in young female and a reddish skin colors in girl,which can provide the guidance for color adjustment of printed skin color images.
基金Supported by the National Natural Science Foundation of China(32072352)。
文摘In order to improve the quality of 3D printed raspberry preserves after post-processing,microwave ovens combining infrared and microwave methods were utilized.The effects of infrared heating temperature,infrared heating time,microwave power,microwave heating time on the center temperature,moisture content,the chroma(C*),the total color difference(ΔE*),shape fidelity,hardness,and the total anthocyanin content of 3D printed raspberry preserves were analyzed by response surface method(RSM).The results showed that under combining with the two methods,infrared heating improved the fidelity and quality degradation of printed products,while microwave heating enhanced the efficiency of infrared heating.Infrared-microwave combination cooking could maintain relatively stable color appearance and shape of 3D printed raspberry preserves.The AHP–CRITIC hybrid weighting method combined with the response surface test to determine the comprehensive weights of the evaluation indicators optimized the process parameters,and the optimal process parameters were obtained:infrared heating temperature of 190℃,infrared heating time of 10 min and 30 s,microwave power of 300 W,and microwave heating time of 2 min and 6 s.The 3D printed raspberry cooking methods obtained under the optimal conditions seldom had color variation,porous structure,uniform texture,and high shape fidelity,which retained the characteristics of personalized manufacturing by 3D printing.This study could provide a reference for the postprocessing and quality control of 3D cooking methods.
文摘Additive Manufacturing(AM)can provide customized parts that conventional techniques fail to deliver.One important parameter in AM is the quality of the parts,as a result of the material extrusion 3D printing(3D-P)procedure.This can be very important in defense-related applications,where optimum performance needs to be guaranteed.The quality of the Polyetherimide 3D-P specimens was examined by considering six control parameters,namely,infill percentage,layer height,deposition angle,travel speed,nozzle,and bed temperature.The quality indicators were the root mean square(Rq)and average(Ra)roughness,porosity,and the actual to nominal dimensional deviation.The examination was performed with optical profilometry,optical microscopy,and micro-computed tomography scanning.The Taguchi design of experiments was applied,with twenty-five runs,five levels for each control parameter,on five replicas.Two additional confirmation runs were conducted,to ensure reliability.Prediction equations were constructed to express the quality indicators in terms of the control parameters.Three modeling approaches were applied to the experimental data,to compare their efficiency,i.e.,Linear Regression Model(LRM),Reduced Quadratic Regression Model,and Quadratic Regression Model(QRM).QRM was the most accurate one,still the differences were not high even considering the simpler LRM model.
基金Projects(2019-ZD08,2020-Z17)supported by the State Key Lab of Advanced Metals and Materials,ChinaProject(52004027)supported by the National Natural Science Foundation of China+2 种基金Project(GDOE[2019]A16)supported by the Guangdong MEPP Fund,ChinaProject(311020012)supported by the Innovation Group Project of Southern Marine Science and Engineering Guangdong Laboratory(Zhuhai),ChinaProject(FRF-GF-20-05A)supported by the Fundamental Research Funds for the Central Universities,China。
文摘Due to their high hardness and high strength,VC reinforced hard materials such as high vanadium high-speed steel(HVHSS)are not suitable for machining to obtain complex shape with low cost.Therefore,3D gel printing(3DGP)was employed to print HVHSS parts,using highly loaded slurry with 60%solid content as printing slurry.After printing parameters optimization,the printing sample had good surface quality,and obvious printing lines were observed.The extruded filament was in-situ cured,thus enough to maintain the designed shape.Uniform sintering shrinkage with a shrinkage rate of about 15%was obtained in the as-sintered sample with relative density of 99%.The surface roughness decreased from 6.5μm to 3.8μm.Fine carbides(<1μm)and dense microstructure were achieved.Besides,the as-sintered sample had comprehensive performance of HRC60 in hardness,3000 MPa in bend strength,and 20−26 J in impact energy.This study proposed one promising method to directly manufacture complex-shaped hard materials without subsequent machining.
基金Project(B07024) supported by Biomedical Textile Materials "111 Project" from Ministry of Education of ChinaProject(50773009) supported by the National Natural Science Foundation of ChinaProject(Grant IRT0526) supported by Program for Changjiang Scholars and Innovative Research Team in University
文摘Rheological properties of microemulsions(MEs) and their printability in three dimensional printing(3DP) systems were investigated.A series of MEs with different contents of oil phase were prepared using sonication method with ibuprofen as model drug and soybean lecithin as emulfier.Stationary and transient rheological properties of MEs were investigated by ARES-SRF using concentric cylinders measuring systems.3DP systems with piezoelectric drop-on-demand print heads were employed to test the printability of the MEs.Results demonstrate that the apparent viscosity and dynamic linear viscoelastic regions of the MEs are the most important parameters for continuous and stable printing of MEs by 3DP.The incorporation of drug in the MEs has little influence on the MEs' stationary rheological behaviors and dynamic viscoelasticity,but the concentration of oil phase has a strong influence on them.The rheological property of binder liquids has a close relationship with their printability in 3DP system.
基金Projects(51074190,51234009)supported by the National Natural Science Foundation of ChinaProject(2014DFA90520)supported by International Cooperation Program of Ministry of Science of ChinaProject(20110162110049)supported by the Doctoral Scientific Fund Project of the Ministry of Education of China
文摘A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.
基金We gratefully acknowledge the support from National Natural Science Foundation of China(Grant No.22075145).
文摘Conventional exploding foil initiator (EFI) in ignition or detonation applications hosts many performance advantages, but was hindered by the bulky, inaccurate, inefficient and expensive shortcomings. We highlight a novel micro-chip exploding foil initiator (McEFI) using printed circuit board (PCB) technology. The structural parameters were determined based on energy coupling relationship at the component interfaces. Next, the prototype McEFI has been batch-fabricated using PCB technology, with a monolithic structure of 7.0 mm (l) × 4.5 mm (w) × 4.0 mm (δ). As expected, this PCB-McEFI illustrated the successful firing validations for explosives pellets. This paper has addressed the cost problem in both military munitions and civil markets wherever reliable, insensitive and timing-dependent ignition or detonation are involved.
文摘The crushing performance of printed circuit board (PCB) was studied on several crushers. The results show that PCB is a material which is difficult to crush. The crushing performance of PCB with disk crusher, especially vibration grinding, which has cut or impact action, excels that of jaw crusher or roller crusher. The PCB scrap is worthwhile to recycle using variety of modern characterization methods. When compared with natural resources, this material stream remains a rich precious metal and nonferrous metals. In PCB scrap, metals account for 47% of the total material composition, in which there exists 19.66% copper, 11.47% iron, 3.93% lead, 300 g/t gold and 510 kg/t silver, etc. In addition, the PCB scrap contains 27% of plastics and 26% of refractory oxides.
基金Project(2006AA06Z375) supported by the National High-tech Research and Development Program of China
文摘Thermal decomposition of waste epoxy PCBs was performed in different atmospheres （nitrogen, argon, air and vacuum） at a heating rate of 10 ℃/rain by DSC-TGA, and the pyrolysis characteristic was analyzed. The gases volatilized from the experiment were qualitatively analyzed by TG-FTIR. Kinetics study shows that pyrolysis reaction takes place between 300 and 400℃, and the activation energies are 256, 212 and 186.2 kJ/mol in nitrogen, argon and vacuum, respectively. There are two mass-loss processes in the decomposition under air atmosphere. In the first mass-loss process, the decomposition is the main reaction, and in the second process, the oxidation is the main reaction. The activation energy of the second mass-loss process is 99.6 kJ/mol by isothermal heat-treatments. TG-FTIR analysis shows carbon dioxide, carbon monoxide, hydrogen bromide, phenol and substituent phenol are given off during the pyrolysis of waste epoxy PCBs.
基金Project(51901020)supported by the National Natural Science Foundation of ChinaProject(2019JZZY010327)supported by Shandong Key Research and Development Plan,China+1 种基金Project(201942074001)supported by Aeronautical Science Foundation of ChinaProject(FRF-IP-20-05)supported by the Fundamental Research Funds for the Central Universities,China。
文摘Additive manufacturing(AM),also known as 3D-printing(3DP)technology,is an advanced manufacturing technology that has developed rapidly in the past 40 years.However,the ceramic material printing is still challenging because of the issue of cracking.Indirect 3D printing has been designed and drawn attention because of its high manufacturing speed and low cost.Indirect 3D printing separates the one-step forming process of direct 3D printing into binding and material sintering,avoiding the internal stress caused by rapid cooling,making it possible to realize the highquality ceramic component with complex shape.This paper presents the research progress of leading indirect 3D printing technologies,including binder jetting(BJ),stereolithography(SLA),and fused deposition modeling(FDM).At present,the additive manufacturing of ceramic materials is mainly achieved through indirect 3D printing technology,and these materials include silicon nitride,hydroxyapatite functional ceramics,silicon carbide structural ceramics.
文摘Three-dimensional(3D)micro-jet printing is a droplet deposition technique based on liquid-phase materials.To improve the deposition density and performance of energetic films with micro/nanoscale on an energetic chip,polydopamine(PDA)was utilized as a linker bridge to induce the in-situ self-assembly of CL-20-based energetic film via 3D micro-jet printing.The self-assembly was extensively characterized by confocal laser scanning microscopy(CLSM),SEM,power-XRD,XPS,and DSC.The performance of the self-assembled film was verified by the mechanical properties and detonation properties,and a possible self-assembly mechanism in the layer-by-layer micro-jet printing process was proposed.The results indicated PDA-induced self-assembly enhanced the physical entanglement between the binders and energetic crystal,reduced the porosity from 15.87%to 11.28%,and improved the elastic modulus and the detonation performance of the CL-20-based energetic film.This work proposes a novel and promising energetic film design and fabrication strategy to enhance the interaction between the energetic composite layers in the micro-jet printing process.
基金funded by the American Heart Association Scientist Development Grant SDG12050083National Institutes of Health grant R21 HL102773
文摘Introduction:3D bio-printing technology<sup>[1-3]</sup>（Figure 1）capable of dispensing live cells,soluble factors,and phase-changing hydrogel in a desired pattern,has great potential in creating 3D tissue.However,maintaining the viability of a thick tissue structure during tissue growth and maturation is challenging due to lack of adequate vascular perfusion.In a simple tissue model with
