Because of an unfortunate mistake by authors,the Project(5227010679)of Foundation item was wrong.The corrected Project is shown as follows:Project(52271073).
The process of preparing anodic oxide film containing active sites and electroless nickel plating on highly active rare earth magnesium alloy was developed.The formation mechanism of electroless nickel plating on acti...The process of preparing anodic oxide film containing active sites and electroless nickel plating on highly active rare earth magnesium alloy was developed.The formation mechanism of electroless nickel plating on active anodic oxide film and the structure and properties of the composite coating were studied by several surface and electrochemical techniques.The results showed that Ag nanograins with an average size of 10 nm were embedded into the anodic oxide film with pores of 0.1−2μm.Ag nanoparticles provided a catalytic site for the deposition of Ni-B alloy,and the Ni crystal nucleus was first grown in horizontal mode and then in cylindrical mode.The corrosion potential of the composite coating increased by 1.37 V and the corrosion current reduced two orders of magnitude due to the subsequent deposition of Ni-P alloy.The high corrosion resistance was attributed to the misaligning of these micro defects in the three different layers and the amorphous structure of the Ni-P alloy in the outer layer.These findings provide a new idea for electroless nickel plating on anodic oxide film.展开更多
Ni/n-SiO2 composite coating was electrodeposited by brush-plating with pulse-reverse current（RC）. The morphology, hardness, and tribological properties of the coating were investigated and compared with those of Ni ...Ni/n-SiO2 composite coating was electrodeposited by brush-plating with pulse-reverse current（RC）. The morphology, hardness, and tribological properties of the coating were investigated and compared with those of Ni and composite coatings electrodeposited with direct current（DC）. The results indicate that Ni/n-SiO2 composite coating electrodeposited by RC, because of RC and the nano powders, has denser coating, finer crystal grains, higher hardness（HV650.0, nearly 1.5 times higher than that of Ni coating electrodeposited by DC） and lower friction coefficient（nearly 0.62）, as a result, in the wearing experiment, the Ni/n-SiO2 composite coating electrodeposited by RC has the least worn loss. So this kind of coating has better wear resistance. And RC electro brush-plating can be used as a new technology of brush-plating in the area of wear resistance.展开更多
To protect carbon/carbon (C/C) composites from oxidation, a SiC coating modified with SiO2 was prepared by a complex technology. The inner SiC coating with thickness varying from 150 to 300 μm was initially coated by...To protect carbon/carbon (C/C) composites from oxidation, a SiC coating modified with SiO2 was prepared by a complex technology. The inner SiC coating with thickness varying from 150 to 300 μm was initially coated by chemical vapor reaction (CVR): a simple and cheap technique to prepare the SiC coating via siliconizing the substrate that was exposed to the mixed vapor (Si and SiO2) at high temperatures (1 923?2 273 K). Then the as-prepared coating was processed by a dipping and drying procedure with tetraethoxysilane as source materials to form SiO2 to fill the cracks and holes. Oxidation tests show that, after oxidation in air at 1 623 K for 10 h and thermal cycling between 1 623 K and room temperature 5 times, the mass loss of the CVR coated sample is up to 18.21%, while the sample coated with modified coating is only 5.96%, exhibiting an obvious improvement of oxidation and thermal shock resistance of the coating. The mass loss of the modified sample is mainly contributed to the reaction of C/C substrate with oxygen diffusing through the penetrating cracks formed in thermal shock tests.展开更多
The electrical resistivity of TiB2/C cathode composite coating at different temperatures was measured with the electrical conductivity test device; the effects of TiB2 content and kinds of carbonaceous fillers as well...The electrical resistivity of TiB2/C cathode composite coating at different temperatures was measured with the electrical conductivity test device; the effects of TiB2 content and kinds of carbonaceous fillers as well as their mean particle size on their electrical resistivities were investigated. The results show that electrical resistivity of the coating decreases with the increase of TiB2 content and the decrease of its mean particle size. When the mass fraction of TiB2 increases from 30% to 60%, the electrical resistivity of the coating at room temperature decreases from 31.2μΩ·m to 23.8μΩ·m. The electrical resistivity of the coating at 960℃ lowers from 76.1μΩ· m to 38.4μΩ·m with the decrease of TiB2 mean particle size from 12μm to 1μm. The kinds of carbonaceous fillers have great influence on the electrical resistivity of TiB2/C composite coating at 960℃, when the graphite, petroleum coke and anthracite are used as fillers, the electrical resistivities of the coating are 20.3μΩ·m, 53.7μΩ·m and 87.2μΩ·m, respectively. For the coating with petroleum coke filler, its electrical resistivity decreases with the increase of the mean particle size of petroleum coke filler. The electrical resistivity at 960℃ decreases from 56.2μΩ·m to 48.2μΩ·m with the mean particle size of petroleum coke increasing from 44μm to 1200μm. However, too big carbonaceous particle size has adverse influence on the abrasion resistance of coating. Its proper mean particle size is 420μm.展开更多
Nanostructured FeS-SiC coating was deposited by atmospheric plasma spraying（APS）.The microstructure and phase composition of the coating were characterized with SEM and XRD,respectively.In addition,the size distribu...Nanostructured FeS-SiC coating was deposited by atmospheric plasma spraying（APS）.The microstructure and phase composition of the coating were characterized with SEM and XRD,respectively.In addition,the size distribution of the reconstituted powders and the porosity of the coating have been measured.It was found that the reconstitiuted powers with sizes in the range of 20 to 80 μm had excellent flowability and were suitable for plasma spraying process.The as-sprayed FeS-SiC composite coating exhibited a bimodal distribution with small grains（30～80nm） and large grains（100～200nm）.The coating was mainly composed of FeS and SiC,a small quantity of Fe1-xS and oxide were also found.The porosity of the coating was approximately 19%.展开更多
Fe-6.5Si soft magnetic composites(SMCs)with hybrid phosphate-silica insulation coatings have been designed to improve their comprehensive property via chemical coating combining sol-gel method in this work.The microst...Fe-6.5Si soft magnetic composites(SMCs)with hybrid phosphate-silica insulation coatings have been designed to improve their comprehensive property via chemical coating combining sol-gel method in this work.The microstructure and magnetic performance of the Fe-6.5Si SMCs with hybrid phosphate-silica insulation coatings were investigated.The hybrid phosphate-silica coatings with high heat resistance and high withstand pressure,formed on the surface of the Fe-6.5Si ferromagnetic powders,were found stable in the composites.Compared with Fe-6.5Si SMCs coated by single phosphate or single silica,Fe-6.5Si SMCs with hybrid phosphate-silica show much higher permeability and lower core loss.The work provides a new way to optimize the magnetic performance of soft magnetic composites.展开更多
Carbon-carbon composite （C/C） materials are prone to severe oxidation and volatilization problems. To address these issues, mullite （3Al2O3.2SiO2）/silicon carbide （SIC） coatings were deposited on C/C composite s...Carbon-carbon composite （C/C） materials are prone to severe oxidation and volatilization problems. To address these issues, mullite （3Al2O3.2SiO2）/silicon carbide （SIC） coatings were deposited on C/C composite substrates characterized into high and low densities. The coatings were applied by a two-step approach： pack cementation and silica sol based slurry coating processes. The relationship between the microstructure of 3Al2O3·2SiO2/SiC coatings and C/C substrates during isothermal oxidation cycle at 1 500 ℃ was investigated using X-ray diffractometer （XRD） and scanning electron microscope （SEM） mounted with energy dispersive spectrometer （EDS）. The results indicate that the density of the substrates has a marked effect on the coatings. Dense, thick and well-bonded coatings are obtained in the high density substrate. After 106 h of isothermal oxidation, the high density substrate with 3Al2O3-2SiO2/SiC coating offers effective protection as compared to low density substrate suffering recession.展开更多
Mg-6%Zn-10%β-Ca3(PO4)2 composite was prepared through powder metallurgy methods with different chitosan coatings on its surface. The properties of the chitosan coatings on the surface of Mg-6%Zn-10%β-Ca3(PO4)2 compo...Mg-6%Zn-10%β-Ca3(PO4)2 composite was prepared through powder metallurgy methods with different chitosan coatings on its surface. The properties of the chitosan coatings on the surface of Mg-6%Zn-10%β-Ca3(PO4)2 composite, such as the adhesion ability, the corrosion behavior and the cytotoxicity properties, were investigated, and the microstructure of the chitosan coating was observed by scanning electron microscope(SEM). The results show that chitosan coating improves the corrosion resistance of the magnesium composite specimens significantly. Mg-6%Zn-10%β-Ca3(PO4)2 composite specimens exhibit good corrosion resistance and low p H values in simulated body fluid(SBF) at 37 °C in the immersion test with 7-layer chitosan coating whose relative molecular mass is 30×104 Da. The cytotoxicity tests indicate that Mg-6%Zn-10%β-Ca3(PO4)2 with chitosan coating is nontoxic with a cytotoxicity grade of zero against L-929 cells, which is better than that of uncoated composites.展开更多
Ni-W-P composite coatings reinforced by Ce O2 and Si O2 nano-particles on the surface of common carbon steels, were prepared by double pulse electrodeposition. The crystallization course was characterized by phase str...Ni-W-P composite coatings reinforced by Ce O2 and Si O2 nano-particles on the surface of common carbon steels, were prepared by double pulse electrodeposition. The crystallization course was characterized by phase structures, crystallinity, grain sizes and microstructures. The results indicate that as-deposited composite coating is amorphous. Whereas it turns into the crystalline structure with 98.25% crystallinity, and Ni3 P, Ni2 P and Ni5P2 alloy phases precipitate from structures at 400 °C. Thereafter, Ni2 P and Ni5P2 metastable alloy phases turn into Ni3 P stable alloy phase at 500 °C. The crystallization course of the composite coating has finished when being heat-treated at 700 °C. The average sizes of Ni grains increase with the rise of heat treatment temperature from400 °C to 700 °C. Ce O2 and Si O2 nano-particles deposited into Ni-W-P alloys can delay the crystallization course and habit the growth of alloy phases.展开更多
The coating of Ni W P was deposited as base layer, and then the composite coating of Ni Ti(particles) Re(rare earth) was deposited subsequently on the surface of diamond using electroless plating by adding 2...The coating of Ni W P was deposited as base layer, and then the composite coating of Ni Ti(particles) Re(rare earth) was deposited subsequently on the surface of diamond using electroless plating by adding 2～3 μm Ti particles and trace rare earth salt to bath solution. Ti particles deposited on the surface of diamond were found by SEM and formation of TiC was verified by X ray diffraction analysis after heat treatment of the coatings in vacuum at 900 ℃. The binding strength between the coated diamond and the metal matrix was improved effectively in the diamond composite based on metal cement.展开更多
Fe-Al intermetallics with remarkable high-temperature intensity and excellent erosion, high-temperature oxidation and sulfuration resistance are potential low cost high-temperature structural materials. But the room t...Fe-Al intermetallics with remarkable high-temperature intensity and excellent erosion, high-temperature oxidation and sulfuration resistance are potential low cost high-temperature structural materials. But the room temperature brittleness induces shape difficult and limits its industrial application. The Fe-Al intermetallic coatings were prepared by high velocity arc spraying technology with cored wire on 20G steel, which will not only obviate the problems faced in fabrication of these alloys into useful shapes, but also allow the effective use of their outstanding high-temperature performance. The Fe-Al/WC intermetallic composite coatings were prepared by high velocity arc spraying technology on 20G steel and the oxidation performance of Fe-Al/WC composite coatings was studied by means of thermogrativmetic analyzer at 450, 650 and 800℃. The results demonstrate that the kinetics curve of oxidation at three temperatures approximately follows the logarithmic law. The composition of the oxidized coating is mainly composed of Al2O3, Fe2O3, Fe3O4 and FeO. These phases distribute unevenly. The protective Al2O3 film firstly forms and preserves the coatings from further oxidation.展开更多
Ni-Co-Fe2O3 composite coatings were electrodeposited using cetyltrimethylammonium bromide(CTAB)-modified Watt's nickel bath with Fe2O3 particles dispersed in it.The effects of the plating parameters on the chemica...Ni-Co-Fe2O3 composite coatings were electrodeposited using cetyltrimethylammonium bromide(CTAB)-modified Watt's nickel bath with Fe2O3 particles dispersed in it.The effects of the plating parameters on the chemical composition,structural and morphological characteristics of the electrodeposited Ni-Co-Fe2O3 composite coatings were investigated by energy dispersive X-ray(EDS) spectroscopy,X-ray diffractometry(XRD) and scanning electron microscopy(SEM).The results reveal that Fe2O3 particles can be codeposited in the Ni-Co matrix.The codeposition of Fe2O3 particles with Ni-Co is favoured at high Fe2O3 particle concentration and medium stirring,and the deposition of Co is favoured at high concentration of CTAB.Moreover,the study of the textural perfection of the deposits reveals that the presence of particles leads to the worsening of the quality of the observed <220> preferred orientation.Composites with high concentration of embedded particles exhibit a preferred crystal orientation of <111>.The more the embedded Fe2O3 particles in the metallic matrix,the smaller the sizes of the crystallite for the composite deposits.展开更多
Nano-SiO2 particles strengthened Ni-based composite coating was designed and prepared on steel substrate. The structures and nanoparticle content of the nano-SiO2/Ni composite coating were determined by SEM, EDS and T...Nano-SiO2 particles strengthened Ni-based composite coating was designed and prepared on steel substrate. The structures and nanoparticle content of the nano-SiO2/Ni composite coating were determined by SEM, EDS and TEM; and the micro mechanical properties were tested by nano-indentation technique. The results show that 56% of particles in the solution are dispersed in size of less than 100nm, the content of nanoparticles co-deposited in the coating doubles and structure of the coating is more compact and uniform than that of Ni coating. Nano-SiO2/Ni coating exhibits excellent micro mechanical properties, and the nanohardness and elastic modulus are 7.81GPa and 198GPa, respectively, which are attributed to finer crystal strengthening, dispersion strengthening and high-density dislocation strengthening of nano-SiO2 particles to the composite coatings.展开更多
The reactive process for Al/SiC P composite was studied. SiC particles were in situ coated by the exothermal reaction of SiC Ti powder compact in Al melt bath, and easily incorporated into Al melt. The detailed study ...The reactive process for Al/SiC P composite was studied. SiC particles were in situ coated by the exothermal reaction of SiC Ti powder compact in Al melt bath, and easily incorporated into Al melt. The detailed study was carried out to understand the microstructures of the reacted SiC particles. During the reaction and consequent mixing, the successive processes include in situ coating on the reacted SiC particles, coat dissolution and SiC P splitting. The tensile mechanical properties of 6013Al/SiC P composite processed by the present technology showed that the reacted SiC P considerably reinforced the 6013 matrix.展开更多
The electrodeposition of nickel-silicon carbide coatings on a copper electrode was done by mixing SiC particles in the nickel electrodeposition solution.The influence of surfactants and silicon carbide particle size o...The electrodeposition of nickel-silicon carbide coatings on a copper electrode was done by mixing SiC particles in the nickel electrodeposition solution.The influence of surfactants and silicon carbide particle size on uniformity and quantity of silicon carbide particles in nickel-silicon carbide composite coatings was investigated.It was found that particle size affects the nucleation overpotential,with 40 nm silicon carbide nanoparticles more effective in promoting nickel nucleation than 500 nm particles due to an increase in active nucleation sites.In terms of surfactants,anionic surfactant sodium dodecyl sulfate(SDS)produced better dispersion of 40 nm silicon carbide particles than cationic surfactant cetyltrimethyl ammonium bromide(CTAB),but little difference was found between the two when 500 nm silicon carbide particles were used.Thus,although the suspension of silicon carbide particles can be improved and their co-deposition can be promoted with a cationic surfactant CTAB,it is less effective than an anionic surfactant SDS in terms of surface finish.展开更多
Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide(2D-SiC/SiC)composites were molded by stacking method and densified through precursor infiltration and pyrolysis(PIP)process.SiC coati...Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide(2D-SiC/SiC)composites were molded by stacking method and densified through precursor infiltration and pyrolysis(PIP)process.SiC coating was deposited as the fiber/matrix interphase layer by chemical vapor deposition(CVD)technique.Fiber/matrix debonding and relatively long fiber pullouts were observed on the fracture surfaces.Additionally,the flexural strength and elastic modulus of the composites with and without fiber/matrix interphase layer were investigated using three-point bending test and single-edge notched beam test.The results show that the fiber fraction and the porosity of 2D-SiC/SiC composites with and without coating are 27.2%(volume fraction)and 11.1%,and 40.7%(volume fraction)and 7.5%,respectively.And the flexural strength and elastic modulus of 2D-SiC/SiC composites with and without coating are 363.3 MPa and 127.8 GPa,and 180.2 MPa and 97.2 GPa,respectively.With a proper thickness,the coating can effectively adjust the fiber/matrix interface,thus causing a dramatic increase in the mechanical properties of the composites.展开更多
以硅橡胶为基体,添加无机填料制备的耐热涂层在耐热防腐方面有重要应用前景。采用自制改性硅橡胶作基体,添加不同配比的高岭土、二氧化硅和氧化铝,制备了复合涂层。采用扫描电子显微镜(scanning electron microscopy,SEM)观察了硅橡胶...以硅橡胶为基体,添加无机填料制备的耐热涂层在耐热防腐方面有重要应用前景。采用自制改性硅橡胶作基体,添加不同配比的高岭土、二氧化硅和氧化铝,制备了复合涂层。采用扫描电子显微镜(scanning electron microscopy,SEM)观察了硅橡胶基体中无机填料的分散状况,采用热重分析仪(thermogravimetric analyzer,TGA)对复合涂层的热解温度和失重率进行了分析。结果表明:在复合体系中,无机填料与基体的相容性较好,分散均匀;与基体材料相比,无机填料的添加可有效提高复合材料的耐热性。填料质量分数为20%的复合涂层,其在800℃时质量残留率比自制改性硅橡胶的基体提高了10%以上。展开更多
文摘Because of an unfortunate mistake by authors,the Project(5227010679)of Foundation item was wrong.The corrected Project is shown as follows:Project(52271073).
基金Project(5227010679)supported by the National Natural Science Foundation of China。
文摘The process of preparing anodic oxide film containing active sites and electroless nickel plating on highly active rare earth magnesium alloy was developed.The formation mechanism of electroless nickel plating on active anodic oxide film and the structure and properties of the composite coating were studied by several surface and electrochemical techniques.The results showed that Ag nanograins with an average size of 10 nm were embedded into the anodic oxide film with pores of 0.1−2μm.Ag nanoparticles provided a catalytic site for the deposition of Ni-B alloy,and the Ni crystal nucleus was first grown in horizontal mode and then in cylindrical mode.The corrosion potential of the composite coating increased by 1.37 V and the corrosion current reduced two orders of magnitude due to the subsequent deposition of Ni-P alloy.The high corrosion resistance was attributed to the misaligning of these micro defects in the three different layers and the amorphous structure of the Ni-P alloy in the outer layer.These findings provide a new idea for electroless nickel plating on anodic oxide film.
文摘Ni/n-SiO2 composite coating was electrodeposited by brush-plating with pulse-reverse current（RC）. The morphology, hardness, and tribological properties of the coating were investigated and compared with those of Ni and composite coatings electrodeposited with direct current（DC）. The results indicate that Ni/n-SiO2 composite coating electrodeposited by RC, because of RC and the nano powders, has denser coating, finer crystal grains, higher hardness（HV650.0, nearly 1.5 times higher than that of Ni coating electrodeposited by DC） and lower friction coefficient（nearly 0.62）, as a result, in the wearing experiment, the Ni/n-SiO2 composite coating electrodeposited by RC has the least worn loss. So this kind of coating has better wear resistance. And RC electro brush-plating can be used as a new technology of brush-plating in the area of wear resistance.
基金Project(2006CB600901) supported by the National Basic Research Program of ChinaProject(50802115) supported by the National Natural Science Foundation of China
文摘To protect carbon/carbon (C/C) composites from oxidation, a SiC coating modified with SiO2 was prepared by a complex technology. The inner SiC coating with thickness varying from 150 to 300 μm was initially coated by chemical vapor reaction (CVR): a simple and cheap technique to prepare the SiC coating via siliconizing the substrate that was exposed to the mixed vapor (Si and SiO2) at high temperatures (1 923?2 273 K). Then the as-prepared coating was processed by a dipping and drying procedure with tetraethoxysilane as source materials to form SiO2 to fill the cracks and holes. Oxidation tests show that, after oxidation in air at 1 623 K for 10 h and thermal cycling between 1 623 K and room temperature 5 times, the mass loss of the CVR coated sample is up to 18.21%, while the sample coated with modified coating is only 5.96%, exhibiting an obvious improvement of oxidation and thermal shock resistance of the coating. The mass loss of the modified sample is mainly contributed to the reaction of C/C substrate with oxygen diffusing through the penetrating cracks formed in thermal shock tests.
基金Project(2005CB623703) supported by the State Key Fundamental Research and Development Programof China project(5JJ30103) supported by the Natural Science Foundation of Hunan Province
文摘The electrical resistivity of TiB2/C cathode composite coating at different temperatures was measured with the electrical conductivity test device; the effects of TiB2 content and kinds of carbonaceous fillers as well as their mean particle size on their electrical resistivities were investigated. The results show that electrical resistivity of the coating decreases with the increase of TiB2 content and the decrease of its mean particle size. When the mass fraction of TiB2 increases from 30% to 60%, the electrical resistivity of the coating at room temperature decreases from 31.2μΩ·m to 23.8μΩ·m. The electrical resistivity of the coating at 960℃ lowers from 76.1μΩ· m to 38.4μΩ·m with the decrease of TiB2 mean particle size from 12μm to 1μm. The kinds of carbonaceous fillers have great influence on the electrical resistivity of TiB2/C composite coating at 960℃, when the graphite, petroleum coke and anthracite are used as fillers, the electrical resistivities of the coating are 20.3μΩ·m, 53.7μΩ·m and 87.2μΩ·m, respectively. For the coating with petroleum coke filler, its electrical resistivity decreases with the increase of the mean particle size of petroleum coke filler. The electrical resistivity at 960℃ decreases from 56.2μΩ·m to 48.2μΩ·m with the mean particle size of petroleum coke increasing from 44μm to 1200μm. However, too big carbonaceous particle size has adverse influence on the abrasion resistance of coating. Its proper mean particle size is 420μm.
基金The authors would like to thank National Natural Science Foundation of China (No. 50375015) for supporting.
文摘Nanostructured FeS-SiC coating was deposited by atmospheric plasma spraying（APS）.The microstructure and phase composition of the coating were characterized with SEM and XRD,respectively.In addition,the size distribution of the reconstituted powders and the porosity of the coating have been measured.It was found that the reconstitiuted powers with sizes in the range of 20 to 80 μm had excellent flowability and were suitable for plasma spraying process.The as-sprayed FeS-SiC composite coating exhibited a bimodal distribution with small grains（30～80nm） and large grains（100～200nm）.The coating was mainly composed of FeS and SiC,a small quantity of Fe1-xS and oxide were also found.The porosity of the coating was approximately 19%.
基金Projects(2020GDSYL-20200402008,2018GDASCX-0117)supported by GDAS’Project of Science and Technology Development,ChinaProjects(2015B010136004,2019A1515010886)supported by Science and Technology Planning Project of Guangdong Province of ChinaProject(1920001001392)supported by Key Technology Project of Foshan,China。
文摘Fe-6.5Si soft magnetic composites(SMCs)with hybrid phosphate-silica insulation coatings have been designed to improve their comprehensive property via chemical coating combining sol-gel method in this work.The microstructure and magnetic performance of the Fe-6.5Si SMCs with hybrid phosphate-silica insulation coatings were investigated.The hybrid phosphate-silica coatings with high heat resistance and high withstand pressure,formed on the surface of the Fe-6.5Si ferromagnetic powders,were found stable in the composites.Compared with Fe-6.5Si SMCs coated by single phosphate or single silica,Fe-6.5Si SMCs with hybrid phosphate-silica show much higher permeability and lower core loss.The work provides a new way to optimize the magnetic performance of soft magnetic composites.
基金Project(2011CB605805) supported by the National Basic Research Program of ChinaProject(51021063) supported by the Creative Research Group of National Natural Science Foundation of China
文摘Carbon-carbon composite （C/C） materials are prone to severe oxidation and volatilization problems. To address these issues, mullite （3Al2O3.2SiO2）/silicon carbide （SIC） coatings were deposited on C/C composite substrates characterized into high and low densities. The coatings were applied by a two-step approach： pack cementation and silica sol based slurry coating processes. The relationship between the microstructure of 3Al2O3·2SiO2/SiC coatings and C/C substrates during isothermal oxidation cycle at 1 500 ℃ was investigated using X-ray diffractometer （XRD） and scanning electron microscope （SEM） mounted with energy dispersive spectrometer （EDS）. The results indicate that the density of the substrates has a marked effect on the coatings. Dense, thick and well-bonded coatings are obtained in the high density substrate. After 106 h of isothermal oxidation, the high density substrate with 3Al2O3-2SiO2/SiC coating offers effective protection as compared to low density substrate suffering recession.
基金Project(2012zzts068) supported by the Fundamental Research Funds for the Central Universities of Central South University,ChinaProject(2010fj3091) supported by the Open Funding of State Key Laboratory of Powder Metallurgy and Science&Technology Foundation,China
文摘Mg-6%Zn-10%β-Ca3(PO4)2 composite was prepared through powder metallurgy methods with different chitosan coatings on its surface. The properties of the chitosan coatings on the surface of Mg-6%Zn-10%β-Ca3(PO4)2 composite, such as the adhesion ability, the corrosion behavior and the cytotoxicity properties, were investigated, and the microstructure of the chitosan coating was observed by scanning electron microscope(SEM). The results show that chitosan coating improves the corrosion resistance of the magnesium composite specimens significantly. Mg-6%Zn-10%β-Ca3(PO4)2 composite specimens exhibit good corrosion resistance and low p H values in simulated body fluid(SBF) at 37 °C in the immersion test with 7-layer chitosan coating whose relative molecular mass is 30×104 Da. The cytotoxicity tests indicate that Mg-6%Zn-10%β-Ca3(PO4)2 with chitosan coating is nontoxic with a cytotoxicity grade of zero against L-929 cells, which is better than that of uncoated composites.
基金Project(20806035)supported by the National Natural Science Foundation of ChinaProject(2009CI026)supported by the Back-up Personnel Foundation of Academic and Technology Leaders of Yunnan Province,ChinaProject(KKZ6200927001)supported by the Opening Fund of Key Laboratory of Inorganic Coating Materials,Chinese Academy of Sciences
文摘Ni-W-P composite coatings reinforced by Ce O2 and Si O2 nano-particles on the surface of common carbon steels, were prepared by double pulse electrodeposition. The crystallization course was characterized by phase structures, crystallinity, grain sizes and microstructures. The results indicate that as-deposited composite coating is amorphous. Whereas it turns into the crystalline structure with 98.25% crystallinity, and Ni3 P, Ni2 P and Ni5P2 alloy phases precipitate from structures at 400 °C. Thereafter, Ni2 P and Ni5P2 metastable alloy phases turn into Ni3 P stable alloy phase at 500 °C. The crystallization course of the composite coating has finished when being heat-treated at 700 °C. The average sizes of Ni grains increase with the rise of heat treatment temperature from400 °C to 700 °C. Ce O2 and Si O2 nano-particles deposited into Ni-W-P alloys can delay the crystallization course and habit the growth of alloy phases.
文摘The coating of Ni W P was deposited as base layer, and then the composite coating of Ni Ti(particles) Re(rare earth) was deposited subsequently on the surface of diamond using electroless plating by adding 2～3 μm Ti particles and trace rare earth salt to bath solution. Ti particles deposited on the surface of diamond were found by SEM and formation of TiC was verified by X ray diffraction analysis after heat treatment of the coatings in vacuum at 900 ℃. The binding strength between the coated diamond and the metal matrix was improved effectively in the diamond composite based on metal cement.
文摘Fe-Al intermetallics with remarkable high-temperature intensity and excellent erosion, high-temperature oxidation and sulfuration resistance are potential low cost high-temperature structural materials. But the room temperature brittleness induces shape difficult and limits its industrial application. The Fe-Al intermetallic coatings were prepared by high velocity arc spraying technology with cored wire on 20G steel, which will not only obviate the problems faced in fabrication of these alloys into useful shapes, but also allow the effective use of their outstanding high-temperature performance. The Fe-Al/WC intermetallic composite coatings were prepared by high velocity arc spraying technology on 20G steel and the oxidation performance of Fe-Al/WC composite coatings was studied by means of thermogrativmetic analyzer at 450, 650 and 800℃. The results demonstrate that the kinetics curve of oxidation at three temperatures approximately follows the logarithmic law. The composition of the oxidized coating is mainly composed of Al2O3, Fe2O3, Fe3O4 and FeO. These phases distribute unevenly. The protective Al2O3 film firstly forms and preserves the coatings from further oxidation.
基金Project(2005CB623703) supported by the National Key Basic Research Program of ChinaProject(50474051) supported by the National Natural Science Foundation of China+2 种基金Project(CX2009B032) supported by Innovation Foundation for Postgraduate of Hunan Province of China Project(ZKJ2009024) supported by the Precious Apparatus Open Share Foundation of Central South University, ChinaProject(2009ybfz02) supported by Excellent Doctor Support Fund of Central South University,China
文摘Ni-Co-Fe2O3 composite coatings were electrodeposited using cetyltrimethylammonium bromide(CTAB)-modified Watt's nickel bath with Fe2O3 particles dispersed in it.The effects of the plating parameters on the chemical composition,structural and morphological characteristics of the electrodeposited Ni-Co-Fe2O3 composite coatings were investigated by energy dispersive X-ray(EDS) spectroscopy,X-ray diffractometry(XRD) and scanning electron microscopy(SEM).The results reveal that Fe2O3 particles can be codeposited in the Ni-Co matrix.The codeposition of Fe2O3 particles with Ni-Co is favoured at high Fe2O3 particle concentration and medium stirring,and the deposition of Co is favoured at high concentration of CTAB.Moreover,the study of the textural perfection of the deposits reveals that the presence of particles leads to the worsening of the quality of the observed <220> preferred orientation.Composites with high concentration of embedded particles exhibit a preferred crystal orientation of <111>.The more the embedded Fe2O3 particles in the metallic matrix,the smaller the sizes of the crystallite for the composite deposits.
文摘Nano-SiO2 particles strengthened Ni-based composite coating was designed and prepared on steel substrate. The structures and nanoparticle content of the nano-SiO2/Ni composite coating were determined by SEM, EDS and TEM; and the micro mechanical properties were tested by nano-indentation technique. The results show that 56% of particles in the solution are dispersed in size of less than 100nm, the content of nanoparticles co-deposited in the coating doubles and structure of the coating is more compact and uniform than that of Ni coating. Nano-SiO2/Ni coating exhibits excellent micro mechanical properties, and the nanohardness and elastic modulus are 7.81GPa and 198GPa, respectively, which are attributed to finer crystal strengthening, dispersion strengthening and high-density dislocation strengthening of nano-SiO2 particles to the composite coatings.
文摘The reactive process for Al/SiC P composite was studied. SiC particles were in situ coated by the exothermal reaction of SiC Ti powder compact in Al melt bath, and easily incorporated into Al melt. The detailed study was carried out to understand the microstructures of the reacted SiC particles. During the reaction and consequent mixing, the successive processes include in situ coating on the reacted SiC particles, coat dissolution and SiC P splitting. The tensile mechanical properties of 6013Al/SiC P composite processed by the present technology showed that the reacted SiC P considerably reinforced the 6013 matrix.
基金Project(20180550242)supported by the Liaoning Science and Technology Plan,China。
文摘The electrodeposition of nickel-silicon carbide coatings on a copper electrode was done by mixing SiC particles in the nickel electrodeposition solution.The influence of surfactants and silicon carbide particle size on uniformity and quantity of silicon carbide particles in nickel-silicon carbide composite coatings was investigated.It was found that particle size affects the nucleation overpotential,with 40 nm silicon carbide nanoparticles more effective in promoting nickel nucleation than 500 nm particles due to an increase in active nucleation sites.In terms of surfactants,anionic surfactant sodium dodecyl sulfate(SDS)produced better dispersion of 40 nm silicon carbide particles than cationic surfactant cetyltrimethyl ammonium bromide(CTAB),but little difference was found between the two when 500 nm silicon carbide particles were used.Thus,although the suspension of silicon carbide particles can be improved and their co-deposition can be promoted with a cationic surfactant CTAB,it is less effective than an anionic surfactant SDS in terms of surface finish.
基金Project(NCET-07-0228)support by the New Century Excellent Talents in University
文摘Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide(2D-SiC/SiC)composites were molded by stacking method and densified through precursor infiltration and pyrolysis(PIP)process.SiC coating was deposited as the fiber/matrix interphase layer by chemical vapor deposition(CVD)technique.Fiber/matrix debonding and relatively long fiber pullouts were observed on the fracture surfaces.Additionally,the flexural strength and elastic modulus of the composites with and without fiber/matrix interphase layer were investigated using three-point bending test and single-edge notched beam test.The results show that the fiber fraction and the porosity of 2D-SiC/SiC composites with and without coating are 27.2%(volume fraction)and 11.1%,and 40.7%(volume fraction)and 7.5%,respectively.And the flexural strength and elastic modulus of 2D-SiC/SiC composites with and without coating are 363.3 MPa and 127.8 GPa,and 180.2 MPa and 97.2 GPa,respectively.With a proper thickness,the coating can effectively adjust the fiber/matrix interface,thus causing a dramatic increase in the mechanical properties of the composites.
文摘以硅橡胶为基体,添加无机填料制备的耐热涂层在耐热防腐方面有重要应用前景。采用自制改性硅橡胶作基体,添加不同配比的高岭土、二氧化硅和氧化铝,制备了复合涂层。采用扫描电子显微镜(scanning electron microscopy,SEM)观察了硅橡胶基体中无机填料的分散状况,采用热重分析仪(thermogravimetric analyzer,TGA)对复合涂层的热解温度和失重率进行了分析。结果表明:在复合体系中,无机填料与基体的相容性较好,分散均匀;与基体材料相比,无机填料的添加可有效提高复合材料的耐热性。填料质量分数为20%的复合涂层,其在800℃时质量残留率比自制改性硅橡胶的基体提高了10%以上。
