The triaxial strength of twenty rockmass types was predicted using two non-linear triaxial strength criteria for rockmass i.e. Modified Mohr-Coulomb(MMC) criterion and Generalized Hoek-Brown(GHB)criterion. Four differ...The triaxial strength of twenty rockmass types was predicted using two non-linear triaxial strength criteria for rockmass i.e. Modified Mohr-Coulomb(MMC) criterion and Generalized Hoek-Brown(GHB)criterion. Four different rockmass classification systems were used for the calculation of MMC criterion parameters while only GSI classification system has been used for calculation of GHB parameters. The representative value of the uniaxial compressive strength and elastic modulus of rockmass have been estimated using probabilistic approach. A hypothetical case of an unsupported tunnel has been analyzed considering both MMC and GHB criteria. The analysis was done using the convergence-confinement method with two different approaches. The first approach predicts the tunnel response using GHB criterion directly. The second approach predicts the tunnel response using equivalent Mohr-Coulomb parameters obtained by linearization of triaxial data points obtained from MMC and GHB criteria. The tunnel response has been estimated in terms of radius of plastic zone, tunnel convergence and tunnel convergence strain. For very poor rockmasses the tunnel response predicted by MMC criterion is less than that predicted by GHB criterion. For poor and fair rockmass, the tunnel response estimated considering both the criteria are comparable except for few cases. Squeezing condition in rockmass has been also evaluated.展开更多
With the increase of mining depth of mineral resources,the rock mass stress state is being more and more complex.The rock mass show different features,namely,with the increase of hydrostatic pressure,rock mass failure...With the increase of mining depth of mineral resources,the rock mass stress state is being more and more complex.The rock mass show different features,namely,with the increase of hydrostatic pressure,rock mass failure mode turns from brittle tension failure to structure ductile failure and its limit strength also increases.The restriction of minimal principal stress on the initiation and development of microcrack and the change of micro-unit stress state by the intermediate principal stress play a decisive role in the increase of rock mass limit strength.Based on the rock mass failure behavior law under complex stress state and the σ2-dependence on the rock mass strength,we proposed a Modified Mohr-Coulomb(M-MC) strength criterion which is smooth and convex.Finally,the M-MC criterion is validated by multiaxial test data of eight kinds of rock mass.We also compared the fitting results with Mohr-Coulomb criterion(MC).It shows that the new criterion fits the test data better than the Mohr-Coulomb criterion.So the M-MC strength criterion well reveals the rock mass bearing behavior and can be widely used in the rock mass strength analysis.The results can provide theoretical foundations for stability analysis and reinforcement design of complex underground engineering.展开更多
Based on the dynamic loading(1-100 s^(-1)) experiments under different temperatures(223-298 K) and stress states, uniaxial and biaxial strength criterion of a Hydroxyl-terminated polybutadiene(HTPB)based composite sol...Based on the dynamic loading(1-100 s^(-1)) experiments under different temperatures(223-298 K) and stress states, uniaxial and biaxial strength criterion of a Hydroxyl-terminated polybutadiene(HTPB)based composite solid propellant were further investigated. These experiments were conducted through the use of a new uniaxial INSTRON testing machine, different new designed gripping apparatus and samples with different configurations. According to the test results, dynamic uniaxial tensile strength criterion of the propellant was directly constructed with the master curve of the uniaxial maximum tensile stress. Whereas, a new method was proposed to determine the dynamic uniaxial compressive strength of the propellant in this study. Then uniaxial compressive strength criterion of the propellant was constructed based on the related master curve. Moreover, it found that the uniaxial tensilecompressive strength ratio of the propellant is more sensitive to loading temperature under the test conditions. The value of this parameter is about 0.4 at room temperature, and it reduces to 0.2-0.3 at low temperatures. Finally, the theoretical biaxial strength criterion of HTPB propellant under dynamic loading was constructed with the unified strength theory, the uniaxial strength and the typical biaxial tensile strength. In addition, the theoretical limit lines of the principal stress plane for the propellant under dynamic loading at different temperatures were further plotted, and the scope of the limit line increases with decreasing temperature.展开更多
The paper presents an experimental investigation on the strength behaviour of natural rock subjected to polyaxial state of stress. The polyaxial tests were conducted on cubical specimens of sandstone obtained from the...The paper presents an experimental investigation on the strength behaviour of natural rock subjected to polyaxial state of stress. The polyaxial tests were conducted on cubical specimens of sandstone obtained from the Shivpuri district in Madhya Pradesh state of India, The specimens having nominal dimensions of100 mm x 100 mm x 100 mm were tested using a polyaxial testing machine. Twenty-five combinations of intermediate and minor principal stresses were applied and the specimens were loaded till failure occurs. It was observed that the intermediate principal stress has a substantial effect on the strength of the Shivpuri sandstone. A database of rock strength under various combinations of σ_2 and σ_3 was obtained for the Shivpuri sandstone. The database was used to study the predictability of five most commonly used strength criterion. Root mean square error(RMSE), average absolute relative error percentage(AAREP) and coefficient of accordance(COA) were used as indices for the measure of goodness of fit. It was observed that the least error in the prediction was shown by modified Mohr Coulomb criterion followed by modified Weibols and Cook criterion. A probability analysis of the error in prediction was also done.展开更多
In order to study the mechanism of water inrush from a concealed, confined karst cave, we established a fluid–solid coupling model of water inrush from a concealed karst cave ahead of a roadway and a strength reducti...In order to study the mechanism of water inrush from a concealed, confined karst cave, we established a fluid–solid coupling model of water inrush from a concealed karst cave ahead of a roadway and a strength reduction method in a rock pillar for preventing water inrush based on catastrophic theory. Fluid–solid coupling effects and safety margins in a rock pillar were studied. Analysis shows that rock pillar instability, exerted by disturbance stress and seepage stress, is the process of rock pillar catastrophic destabilization induced by nonlinear extension of plastic zones in the rock pillar. Seepage flow emerges in the rock pillar for preventing water inrush, accompanied by mechanical instability of the rock pillar. Taking the accident of a confined karst cave water-inrush of Qiyi Mine as an example, by studying the safety factor of the rock pillar and the relationship between karst cave water pressure and thickness of the rock pillar,it is proposed that rock pillar thickness with a safety factor equal to 1.5 is regarded as the calculated safety thickness of the rock pillar, which should be equal to the sum of the blasthole depth, blasting disturbance depth and the calculated safety thickness of the rock pillar. The cause of the karst water inrush at Qiyi Mine is that the rock pillar was so small that it did not possess a safety margin. Combining fluid–solid coupling theory, catastrophic theory and strength reduction method to study the nonlinear mechanical response of complicated rock engineering, new avenues for quantitative analysis of rock engineering stability evaluation should be forthcoming.展开更多
Gold powder is compressed non-hydrostatically up to 127 GPa in a diamond anvil cell （DAC）, and its angle dispersive X-ray diffraction patterns are recorded. The compressive strength of gold is investigated in a fram...Gold powder is compressed non-hydrostatically up to 127 GPa in a diamond anvil cell （DAC）, and its angle dispersive X-ray diffraction patterns are recorded. The compressive strength of gold is investigated in a framework of the lattice strain theory by the line shift analysis. The result shows that the compressive strength of gold increases continuously with the pressure up to 106 GPa and reaches 2.8 GPa at the highest experimental pressure （127 GPa） achieved in our study. This result is in good agreement with our previous experimental result in a relevant pressure range. The compressive strength of gold may be the major source of the error in the equation-of-state measurement in various pressure environments.展开更多
针对定面射孔施工无法定量评价射孔套管的应力状态和剩余强度的问题,以孔板理论为基础,构建定面射孔套管剩余强度分析模型,并结合有限元分析方法,建立定面射孔套管剩余强度分析方法。研究表明,以Ф139.7 mm×9.17 mm N80定面射孔套...针对定面射孔施工无法定量评价射孔套管的应力状态和剩余强度的问题,以孔板理论为基础,构建定面射孔套管剩余强度分析模型,并结合有限元分析方法,建立定面射孔套管剩余强度分析方法。研究表明,以Ф139.7 mm×9.17 mm N80定面射孔套管为例,1.5簇/m孔密、10 mm孔径保持不变,相位角在15~90°变化,剩余强度降低幅值在8.3%~17.35%之间。1.5簇/m孔密、30°相位角保持不变,孔径在4~18 mm变化,套管剩余强度降低幅值在8.31%~21.70%之间。10 mm孔径、30°相位角保持不变,孔密在1.5~4簇/m变化,剩余强度计算结果与孔密呈负相关,剩余强度降低幅值在8.31%~23.15%之间。孔径、孔密、相位角变化时,对比理论解和数值解,上下限值相差小于8%,剩余强度变化趋势吻合性很好。该研究成果对定面射孔套管合理优化射孔参数具有参考意义,也为定面射孔套管剩余强度分析提供理论支持。展开更多
文摘The triaxial strength of twenty rockmass types was predicted using two non-linear triaxial strength criteria for rockmass i.e. Modified Mohr-Coulomb(MMC) criterion and Generalized Hoek-Brown(GHB)criterion. Four different rockmass classification systems were used for the calculation of MMC criterion parameters while only GSI classification system has been used for calculation of GHB parameters. The representative value of the uniaxial compressive strength and elastic modulus of rockmass have been estimated using probabilistic approach. A hypothetical case of an unsupported tunnel has been analyzed considering both MMC and GHB criteria. The analysis was done using the convergence-confinement method with two different approaches. The first approach predicts the tunnel response using GHB criterion directly. The second approach predicts the tunnel response using equivalent Mohr-Coulomb parameters obtained by linearization of triaxial data points obtained from MMC and GHB criteria. The tunnel response has been estimated in terms of radius of plastic zone, tunnel convergence and tunnel convergence strain. For very poor rockmasses the tunnel response predicted by MMC criterion is less than that predicted by GHB criterion. For poor and fair rockmass, the tunnel response estimated considering both the criteria are comparable except for few cases. Squeezing condition in rockmass has been also evaluated.
基金supported by the National Natural Science Foundation of China (Nos.50774082 and 50804046)
文摘With the increase of mining depth of mineral resources,the rock mass stress state is being more and more complex.The rock mass show different features,namely,with the increase of hydrostatic pressure,rock mass failure mode turns from brittle tension failure to structure ductile failure and its limit strength also increases.The restriction of minimal principal stress on the initiation and development of microcrack and the change of micro-unit stress state by the intermediate principal stress play a decisive role in the increase of rock mass limit strength.Based on the rock mass failure behavior law under complex stress state and the σ2-dependence on the rock mass strength,we proposed a Modified Mohr-Coulomb(M-MC) strength criterion which is smooth and convex.Finally,the M-MC criterion is validated by multiaxial test data of eight kinds of rock mass.We also compared the fitting results with Mohr-Coulomb criterion(MC).It shows that the new criterion fits the test data better than the Mohr-Coulomb criterion.So the M-MC strength criterion well reveals the rock mass bearing behavior and can be widely used in the rock mass strength analysis.The results can provide theoretical foundations for stability analysis and reinforcement design of complex underground engineering.
基金financial support of the National 973 Program in China (No. 61338)the National Funds in China (Nos.11772352, 61407200203 and 51328050101)
文摘Based on the dynamic loading(1-100 s^(-1)) experiments under different temperatures(223-298 K) and stress states, uniaxial and biaxial strength criterion of a Hydroxyl-terminated polybutadiene(HTPB)based composite solid propellant were further investigated. These experiments were conducted through the use of a new uniaxial INSTRON testing machine, different new designed gripping apparatus and samples with different configurations. According to the test results, dynamic uniaxial tensile strength criterion of the propellant was directly constructed with the master curve of the uniaxial maximum tensile stress. Whereas, a new method was proposed to determine the dynamic uniaxial compressive strength of the propellant in this study. Then uniaxial compressive strength criterion of the propellant was constructed based on the related master curve. Moreover, it found that the uniaxial tensilecompressive strength ratio of the propellant is more sensitive to loading temperature under the test conditions. The value of this parameter is about 0.4 at room temperature, and it reduces to 0.2-0.3 at low temperatures. Finally, the theoretical biaxial strength criterion of HTPB propellant under dynamic loading was constructed with the unified strength theory, the uniaxial strength and the typical biaxial tensile strength. In addition, the theoretical limit lines of the principal stress plane for the propellant under dynamic loading at different temperatures were further plotted, and the scope of the limit line increases with decreasing temperature.
基金financial assistance obtained from NRDMS Division,Department of Science and Technology,New Delhi(No.NRDMS/11/3067/014(G)
文摘The paper presents an experimental investigation on the strength behaviour of natural rock subjected to polyaxial state of stress. The polyaxial tests were conducted on cubical specimens of sandstone obtained from the Shivpuri district in Madhya Pradesh state of India, The specimens having nominal dimensions of100 mm x 100 mm x 100 mm were tested using a polyaxial testing machine. Twenty-five combinations of intermediate and minor principal stresses were applied and the specimens were loaded till failure occurs. It was observed that the intermediate principal stress has a substantial effect on the strength of the Shivpuri sandstone. A database of rock strength under various combinations of σ_2 and σ_3 was obtained for the Shivpuri sandstone. The database was used to study the predictability of five most commonly used strength criterion. Root mean square error(RMSE), average absolute relative error percentage(AAREP) and coefficient of accordance(COA) were used as indices for the measure of goodness of fit. It was observed that the least error in the prediction was shown by modified Mohr Coulomb criterion followed by modified Weibols and Cook criterion. A probability analysis of the error in prediction was also done.
基金Financial supports for this work, provided by the National Natural Science Foundation of China (No. 51274097)the Scientific Research Fund of Hunan Provincial Education Department of China (No. 13A020)the Open Projects of State Key Laboratory of Coal Resources and Safe Mining, CUMT (No. 13KF03)
文摘In order to study the mechanism of water inrush from a concealed, confined karst cave, we established a fluid–solid coupling model of water inrush from a concealed karst cave ahead of a roadway and a strength reduction method in a rock pillar for preventing water inrush based on catastrophic theory. Fluid–solid coupling effects and safety margins in a rock pillar were studied. Analysis shows that rock pillar instability, exerted by disturbance stress and seepage stress, is the process of rock pillar catastrophic destabilization induced by nonlinear extension of plastic zones in the rock pillar. Seepage flow emerges in the rock pillar for preventing water inrush, accompanied by mechanical instability of the rock pillar. Taking the accident of a confined karst cave water-inrush of Qiyi Mine as an example, by studying the safety factor of the rock pillar and the relationship between karst cave water pressure and thickness of the rock pillar,it is proposed that rock pillar thickness with a safety factor equal to 1.5 is regarded as the calculated safety thickness of the rock pillar, which should be equal to the sum of the blasthole depth, blasting disturbance depth and the calculated safety thickness of the rock pillar. The cause of the karst water inrush at Qiyi Mine is that the rock pillar was so small that it did not possess a safety margin. Combining fluid–solid coupling theory, catastrophic theory and strength reduction method to study the nonlinear mechanical response of complicated rock engineering, new avenues for quantitative analysis of rock engineering stability evaluation should be forthcoming.
基金Project supported by the Defense Industrial Technology Development Program (Grant No. B1520110001)the Fund of Key Laboratory of Shock Wave and Detonation Physics of China (Grant No. 9140C6703031002)supported by Chinese Academy of Sciences (Grant Nos. KJCX2-SW-N03 and KJCX2SW-N20)
文摘Gold powder is compressed non-hydrostatically up to 127 GPa in a diamond anvil cell （DAC）, and its angle dispersive X-ray diffraction patterns are recorded. The compressive strength of gold is investigated in a framework of the lattice strain theory by the line shift analysis. The result shows that the compressive strength of gold increases continuously with the pressure up to 106 GPa and reaches 2.8 GPa at the highest experimental pressure （127 GPa） achieved in our study. This result is in good agreement with our previous experimental result in a relevant pressure range. The compressive strength of gold may be the major source of the error in the equation-of-state measurement in various pressure environments.
