To address the limitations of existing coupling methods in aero-engine system simulation,which fail to adaptively adjust iterative parameters and coupling relationships,which can result in low efficiency and in⁃stabil...To address the limitations of existing coupling methods in aero-engine system simulation,which fail to adaptively adjust iterative parameters and coupling relationships,which can result in low efficiency and in⁃stability,this study introduces a‘Dynamic Event-Driven Co-Simulation’algorithm integrated with decision tree algorithms.This algorithm separates the overall coupling relationships and the main solver from the primary mod⁃el,utilizing a dynamic event monitoring module to adaptively adjust simulation strategies,including iteration pa⁃rameters,coupling relationships,and convergence criteria.This facilitates efficient adaptive simulations of dy⁃namic events while balancing solution accuracy and computational efficiency.The research focuses on a twinshaft turbofan engine,establishing six system-level models that encompass overall performance and various sub⁃systems based on three coupling methods,along with a multidisciplinary multi-fidelity simulation framework in⁃corporating a 3D CFD nozzle model.The study tests both model exchange and coupled simulation methods under a 14 s transient acceleration and deceleration scenario.In a 100%throttle condition,a high-fidelity nozzle model is used to analyze the sensitivity of different convergence criteria on computational efficiency and accuracy.Re⁃sults indicate that the accuracy and efficiency achieved with this method are comparable to those of PROOSIS soft⁃ware(18 s and 35 s,respectively),while being 71%more efficient than Simulink software(62 s and 120 s,re⁃spectively).Furthermore,appropriately relaxing the convergence criteria for the 0D model(from 10-6 to 10-4)while enhancing those for the 3D model(from 3000 steps to 6000 steps)can effectively balance computational accuracy and efficiency.展开更多
Model-based system-of-systems(SOS)engineering(MBSoSE)is becoming a promising solution for the design of SoS with increasing complexity.However,bridging the models from the design phase to the simulation phase poses si...Model-based system-of-systems(SOS)engineering(MBSoSE)is becoming a promising solution for the design of SoS with increasing complexity.However,bridging the models from the design phase to the simulation phase poses significant challenges and requires an integrated approach.In this study,a unified requirement modeling approach is proposed based on unified architecture framework(UAF).Theoretical models are proposed which compose formalized descriptions from both topdown and bottom-up perspectives.Based on the description,the UAF profile is proposed to represent the SoS mission and constituent systems(CS)goal.Moreover,the agent-based simulation information is also described based on the overview,design concepts,and details(ODD)protocol as the complement part of the SoS profile,which can be transformed into different simulation platforms based on the eXtensible markup language(XML)technology and model-to-text method.In this way,the design of the SoS is simulated automatically in the early design stage.Finally,the method is implemented and an example is given to illustrate the whole process.展开更多
Dominant technology formation is the key for the hightech industry to“cross the chasm”and gain an established foothold in the market(and hence disrupt the regime).Therefore,a stimulus-response model is proposed to i...Dominant technology formation is the key for the hightech industry to“cross the chasm”and gain an established foothold in the market(and hence disrupt the regime).Therefore,a stimulus-response model is proposed to investigate the dominant technology by exploring its formation process and mechanism.Specifically,based on complex adaptive system theory and the basic stimulus-response model,we use a combination of agent-based modeling and system dynamics modeling to capture the interactions between dominant technology and the socio-technical landscape.The results indicate the following:(i)The dynamic interaction is“stimulus-reaction-selection”,which promotes the dominant technology’s formation.(ii)The dominant technology’s formation can be described as a dynamic process in which the adaptation intensity of technology standards increases continuously until it becomes the leading technology under the dual action of internal and external mechanisms.(iii)The dominant technology’s formation in the high-tech industry is influenced by learning ability,the number of adopting users and adaptability.Therein,a“critical scale”of learning ability exists to promote the formation of leading technology:a large number of adopting users can promote the dominant technology’s formation by influencing the adaptive response of technology standards to the socio-technical landscape and the choice of technology standards by the socio-technical landscape.There is a minimum threshold and a maximum threshold for the role of adaptability in the dominant technology’s formation.(iv)The socio-technical landscape can promote the leading technology’s shaping in the high-tech industry,and different elements have different effects.This study promotes research on the formation mechanism of dominant technology in the high-tech industry,presents new perspectives and methods for researchers,and provides essential enlightenment for managers to formulate technology strategies.展开更多
This paper explores the performances of a finite element simulation including four concrete models applied to a full-scale reinforced concrete beam subjected to blast loading. Field test data has been used to compare ...This paper explores the performances of a finite element simulation including four concrete models applied to a full-scale reinforced concrete beam subjected to blast loading. Field test data has been used to compare model results for each case. The numerical modelling has been, carried out using the suitable code LS-DYNA. This code integrates blast load routine(CONWEP) for the explosive description and four different material models for the concrete including: Karagozian & Case Concrete, Winfrith, Continuous Surface Cap Model and Riedel-Hiermaier-Thoma models, with concrete meshing based on 10, 15, and 20 mm. Six full-scale beams were tested: four of them used for the initial calibration of the numerical model and two more tests at lower scaled distances. For calibration, field data obtained employing pressure and accelerometers transducers were compared with the results derived from the numerical simulation. Damage surfaces and the shape of rupture in the beams have been used as references for comparison. Influence of the meshing on accelerations has been put in evidence and for some models the shape and size of the damage in the beams produced maximum differences around 15%. In all cases, the variations between material and mesh models are shown and discussed.展开更多
To address the current problems of poor generality,low real-time,and imperfect information transmission of the battlefield target intelligence system,this paper studies the battlefield target intelligence system from ...To address the current problems of poor generality,low real-time,and imperfect information transmission of the battlefield target intelligence system,this paper studies the battlefield target intelligence system from the top-level perspective of multi-service joint warfare.First,an overall planning and analysis method of architecture modeling is proposed with the idea of a bionic analogy for battlefield target intelligence system architecture modeling,which reduces the difficulty of the planning and design process.The method introduces the Department of Defense architecture framework(DoDAF)modeling method,the multi-living agent(MLA)theory modeling method,and other combinations for planning and modeling.A set of rapid planning methods that can be applied to model the architecture of various types of complex systems is formed.Further,the liveness analysis of the battlefield target intelligence system is carried out,and the problems of the existing system are presented from several aspects.And the technical prediction of the development and construction is given,which provides directional ideas for the subsequent research and development of the battlefield target intelligence system.In the end,the proposed architecture model of the battlefield target intelligence system is simulated and verified by applying the colored Petri nets(CPN)simulation software.The analysis demonstrates the reasonable integrity of its logic.展开更多
To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyur...To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.展开更多
The geometric accuracy of topographic mapping with high-resolution remote sensing images is inevita-bly affected by the orbiter attitude jitter.Therefore,it is necessary to conduct preliminary research on the stereo m...The geometric accuracy of topographic mapping with high-resolution remote sensing images is inevita-bly affected by the orbiter attitude jitter.Therefore,it is necessary to conduct preliminary research on the stereo mapping camera equipped on lunar orbiter before launching.In this work,an imaging simulation method consid-ering the attitude jitter is presented.The impact analysis of different attitude jitter on terrain undulation is conduct-ed by simulating jitter at three attitude angles,respectively.The proposed simulation method is based on the rigor-ous sensor model,using the lunar digital elevation model(DEM)and orthoimage as reference data.The orbit and attitude of the lunar stereo mapping camera are simulated while considering the attitude jitter.Two-dimensional simulated stereo images are generated according to the position and attitude of the orbiter in a given orbit.Experi-mental analyses were conducted by the DEM with the simulated stereo image.The simulation imaging results demonstrate that the proposed method can ensure imaging efficiency without losing the accuracy of topographic mapping.The effect of attitude jitter on the stereo mapping accuracy of the simulated images was analyzed through a DEM comparison.展开更多
The parametric scattering center model of radar tar-get has the advantages of simplicity,sparsity and mechanism relevant,making it widely applied in fields such as radar data compression and rapid generation,radar ima...The parametric scattering center model of radar tar-get has the advantages of simplicity,sparsity and mechanism relevant,making it widely applied in fields such as radar data compression and rapid generation,radar imaging,feature extraction and recognition.This paper summarizes and analyzes the research situation,development trend,and difficult prob-lems on scattering center(SC)parametric modeling from three aspects:parametric representation,determination method of model parameters,and application.展开更多
According to the characteristics of spiral mining head for deep seabed cobalt-rich crust, the kinematic model, cutting loads model, quantity of cutting picks model of mining head, granularity distribution model and en...According to the characteristics of spiral mining head for deep seabed cobalt-rich crust, the kinematic model, cutting loads model, quantity of cutting picks model of mining head, granularity distribution model and energy consumption model were constructed. Based on these models, computer simulation program of cutting loads was developed with VB software. The mechanical parameters of mining head were obtained in the cutting depth range of 5160 mm. Making use of the simulation results, the effect of cutting depth of spiral mining head on the mining process was studied. The results show that the maximum force of single pick is 4.7051kN, the maximum force and torque of spiral drum of mining head are respectively 34.1668kN and 3.8795kN·m at the cutting depth of 160mm.展开更多
OBJECTIVE To explain the high inter-individual variability and the frequency of exceeding the therapeutic reference range and the laboratory alert level of amisulpride,a popula⁃tion pharmacokinetic model in Chinese pa...OBJECTIVE To explain the high inter-individual variability and the frequency of exceeding the therapeutic reference range and the laboratory alert level of amisulpride,a popula⁃tion pharmacokinetic model in Chinese patients with schizophrenia was built based on therapeu⁃tic drug monitoring data to guide individualized therapy.METHODS Plasma concentration data(330 measurements from 121 patients)were ana⁃lyzed using a nonlinear mixed-effects model⁃ing approach with first-order conditional estima⁃tion with interaction(FOCE I).The concentra⁃tions of amisulpride were detected by HPLC-MS/MS.Age,weight,sex,combination medication history and renal function status were evaluated as main covariates.The model was internally val⁃idated using goodness-of-fit,bootstrap and nor⁃malized prediction distribution error.Recom⁃mended dosage regimens for patients with key covariates were estimated on the basis of Monte Carlo simulations and the established model.RESULTS A one-compartment model with first-order absorption and elimination was found to adequately characterize amisulpride concentra⁃tion in Chinese patients with schizophrenia.The population estimates of the apparent volume of distribution(V/F)and apparent clearance(CL/F)were 12.7 L and 1.12 L·h-1,respectively.Age sig⁃nificantly affected the clearance of amisulpride and the final model was as follow:CL/F=1.04×(AGE/32)-0.624(L·h-1).To avoid exceeding the lab⁃oratory alert level(640μg·L-1),the model-based simulation results showed that the recommended dose of amisulpride was no more than 600 mg per day for patients aged 60 years,800 mg per day for those aged 40 years and 1200 mg per day for those aged 20 years,respectively.CON⁃CLUSION Dosage optimization of amisulpride can be carried out according to age to reduce the risk of adverse reactions.The model can be used as a suitable tool for designing individual⁃ized therapy for Chinese patients with schizo⁃phrenia.展开更多
基于中国科学院自主研发的第二代地球系统模式CAS-ESM2.0,本研究通过在陆面分量模式CoLM(Common Land Model)中引入植被水力模型以替换原有的经验性方案,开展了两组34年(1981~2014年)的AMIP(Atmospheric Model Intercomparison Project...基于中国科学院自主研发的第二代地球系统模式CAS-ESM2.0,本研究通过在陆面分量模式CoLM(Common Land Model)中引入植被水力模型以替换原有的经验性方案,开展了两组34年(1981~2014年)的AMIP(Atmospheric Model Intercomparison Project)数值模拟试验,探讨了植被水力方案的引入对中国夏季降水模拟的影响。结果表明,植被水力方案的引入能够显著降低CAS-ESM2.0模式对中国夏季降水气候态的模拟偏差,特别是显著改进了中国东部、青藏高原降水的低估,青藏高原以东的川西地区降水高估的偏差,同时也改善了夏季降水年际变率和极端大雨日数的模拟性能。进一步分析显示,植被水力方案的改进显著减小了土壤湿度在长江流域偏干、青藏高原偏湿的模式模拟偏差,降低了我国中东部以及青藏高原地表感热通量和潜热通量的模拟偏差,改善了模式对陆气相互作用过程的模拟能力。陆气相互作用的改进显著提升了模式对东亚季风环流的模拟,改进后的模式模拟的西北太平洋海平面气压的负偏差显著降低,有利于西南季风以及西北太平洋向我国东部的水汽输送,同时在对流层低层出现反气旋异常响应,有效改善了中国东部南风偏弱及水汽辐合偏弱的模拟偏差,使得我国东部降水负偏差显著减小。以上结果表明,包括植被水力过程的陆气相互作用的合理表述是改善东亚夏季降水模拟的重要途径之一。展开更多
In this paper,we proposed a new design scheme of real time electronic countermeasure simulation system.This paper mainly expounds the modeling and realization methods of each part of the whole simulation system,and th...In this paper,we proposed a new design scheme of real time electronic countermeasure simulation system.This paper mainly expounds the modeling and realization methods of each part of the whole simulation system,and the real-time property of system has been lucubrated.Electronic countermeasure simulation system is the key part of military training of individuals;it can also allow the realistic evaluation of the performance of modern equipments and techniques.As a proof,we have drawn up a series of simulation scenarios,such as radar electronic reconnaissance simulation scenario,to explain the feasibility and the superiority of our modeling scheme in this paper.展开更多
A multi-domain nonlinear dynamic model of a proportional solenoid valve was presented.The electro-magnetic,mechanical and fluid subsystems of the valve were investigated,including their interactions.Governing equation...A multi-domain nonlinear dynamic model of a proportional solenoid valve was presented.The electro-magnetic,mechanical and fluid subsystems of the valve were investigated,including their interactions.Governing equations of the valve were derived in the form of nonlinear state equations.By comparing the simulated and measured data,the simulation model is validated with a deviation less than 15%,which can be used for the structural design and control algorithm optimization of proportional solenoid valves.展开更多
The application of new-designed levitation controller requires extensive validation prior to enter into commercial service. However, huge mounts of approximations and assumptions lead the theoretical analysis away fro...The application of new-designed levitation controller requires extensive validation prior to enter into commercial service. However, huge mounts of approximations and assumptions lead the theoretical analysis away from the engineering practice. The experimental methods are time-consuming and financial expensive, even unrealizable due to the lack of suitable sensors. Numerical simulations can bridge the gap between the theoretical analysis and experimental techniques. A complete overall dynamic model of maglev levitation system is derived in this work, which includes the simple-supported bridges, the calculation of electromagnetic force with more details, the stress of levitation modules and the cabin. Based on the aforementioned model, it shows that the inherent nonlinearity, inner coupling, misalignments between the sensors and actuators, and self-excited vibration are the main issues that should be considered during the design process of controller. Then, the backstepping controller based on the mathematical model of the module with reasonable simplifications is proposed, and the stability proofs are listed. To show the advantage of controller, two numerical simulation experiments are carried out. Finally, the results illustrating closed-loop performance are provided.展开更多
A system of systems(SoS)composes a set of independent constituent systems(CSs),where the degree of authority to control the independence of CSs varies,depending on different SoS types.Key researchers describe four SoS...A system of systems(SoS)composes a set of independent constituent systems(CSs),where the degree of authority to control the independence of CSs varies,depending on different SoS types.Key researchers describe four SoS types with descending levels of central authority:directed,acknowledged,collaborative and virtual.Although the definitions have been recognized in SoS engineering,what is challenging is the difficulty of translating these definitions into models and simulation environments.Thus,we provide a goal-based method including a mathematical baseline to translate these definitions into more effective agent-based modeling and simulations.First,we construct the theoretical models of CS and SoS.Based on the theoretical models,we analyze the degree of authority influenced by SoS characteristics.Next,we propose a definition of SoS types by quantitatively explaining the degree of authority.Finally,we recognize the differences between acknowledged SoS and collaborative SoS using a migrating waterfowl flock by an agentbased model(ABM)simulation.This paper contributes to the SoS body of knowledge by increasing our understanding of the degree of authority in an SoS,so we may identify suitable SoS types to achieve SoS goals by modeling and simulation.展开更多
为了寻求合理简化的流域地形指数水文模型TOPMODEL(Topographic Index model)用于大尺度的陆面模式,推导了土壤表层饱和导水率k0、衰减因子f和地下水补给速率R空间都可变的扩展的TOPMODEL,并将f空间非均匀分布的TOPMODEL与陆面模式SSiB...为了寻求合理简化的流域地形指数水文模型TOPMODEL(Topographic Index model)用于大尺度的陆面模式,推导了土壤表层饱和导水率k0、衰减因子f和地下水补给速率R空间都可变的扩展的TOPMODEL,并将f空间非均匀分布的TOPMODEL与陆面模式SSiB4耦合(SSiB4/GTOP)。通过耦合模型在f空间非均匀条件下进行实际流域的水文模拟,分析f空间非均匀对流域土壤湿度、蒸散发、地表径流、基流和总径流的影响。主要结论有:(1)k0和R的空间变化并不改变经典TOPMODEL原有关系式,只要定义新的地形指数,k0和R空间非均匀TOPMODEL与空间均匀的TOPMODEL并无区别;(2) f空间变化条件下由于局地的地下水埋深还与局地的f值有关,地形指数相同的区域具有水文相似性这一结论不再成立;(3)与f空间均匀的模拟结果相比较,f随海拔高度h i增加而线性减小使模拟的流域土壤湿度、地表径流和流域蒸散减小但使基流和总径流增加;(4) f空间非均匀对流域水文模拟结果有影响,但其影响明显小于流域地形因子的影响。展开更多
文摘To address the limitations of existing coupling methods in aero-engine system simulation,which fail to adaptively adjust iterative parameters and coupling relationships,which can result in low efficiency and in⁃stability,this study introduces a‘Dynamic Event-Driven Co-Simulation’algorithm integrated with decision tree algorithms.This algorithm separates the overall coupling relationships and the main solver from the primary mod⁃el,utilizing a dynamic event monitoring module to adaptively adjust simulation strategies,including iteration pa⁃rameters,coupling relationships,and convergence criteria.This facilitates efficient adaptive simulations of dy⁃namic events while balancing solution accuracy and computational efficiency.The research focuses on a twinshaft turbofan engine,establishing six system-level models that encompass overall performance and various sub⁃systems based on three coupling methods,along with a multidisciplinary multi-fidelity simulation framework in⁃corporating a 3D CFD nozzle model.The study tests both model exchange and coupled simulation methods under a 14 s transient acceleration and deceleration scenario.In a 100%throttle condition,a high-fidelity nozzle model is used to analyze the sensitivity of different convergence criteria on computational efficiency and accuracy.Re⁃sults indicate that the accuracy and efficiency achieved with this method are comparable to those of PROOSIS soft⁃ware(18 s and 35 s,respectively),while being 71%more efficient than Simulink software(62 s and 120 s,re⁃spectively).Furthermore,appropriately relaxing the convergence criteria for the 0D model(from 10-6 to 10-4)while enhancing those for the 3D model(from 3000 steps to 6000 steps)can effectively balance computational accuracy and efficiency.
基金Fifth Electronic Research Institute of the Ministry of Industry and Information Technology(HK07202200877)Pre-research Project on Civil Aerospace Technologies of CNSA(D020101)+2 种基金Zhejiang Provincial Science and Technology Plan Project(2022C01052)Frontier Scientific Research Program of Deep Space Exploration Laboratory(2022-QYKYJHHXYF-018,2022-QYKYJH-GCXD-001)Zhiyuan Laboratory(ZYL2024001)。
文摘Model-based system-of-systems(SOS)engineering(MBSoSE)is becoming a promising solution for the design of SoS with increasing complexity.However,bridging the models from the design phase to the simulation phase poses significant challenges and requires an integrated approach.In this study,a unified requirement modeling approach is proposed based on unified architecture framework(UAF).Theoretical models are proposed which compose formalized descriptions from both topdown and bottom-up perspectives.Based on the description,the UAF profile is proposed to represent the SoS mission and constituent systems(CS)goal.Moreover,the agent-based simulation information is also described based on the overview,design concepts,and details(ODD)protocol as the complement part of the SoS profile,which can be transformed into different simulation platforms based on the eXtensible markup language(XML)technology and model-to-text method.In this way,the design of the SoS is simulated automatically in the early design stage.Finally,the method is implemented and an example is given to illustrate the whole process.
基金supported by the Shanghai Philosophy and Social Science Foundation(2022ECK004)Shanghai Soft Science Research Project(23692123400)。
文摘Dominant technology formation is the key for the hightech industry to“cross the chasm”and gain an established foothold in the market(and hence disrupt the regime).Therefore,a stimulus-response model is proposed to investigate the dominant technology by exploring its formation process and mechanism.Specifically,based on complex adaptive system theory and the basic stimulus-response model,we use a combination of agent-based modeling and system dynamics modeling to capture the interactions between dominant technology and the socio-technical landscape.The results indicate the following:(i)The dynamic interaction is“stimulus-reaction-selection”,which promotes the dominant technology’s formation.(ii)The dominant technology’s formation can be described as a dynamic process in which the adaptation intensity of technology standards increases continuously until it becomes the leading technology under the dual action of internal and external mechanisms.(iii)The dominant technology’s formation in the high-tech industry is influenced by learning ability,the number of adopting users and adaptability.Therein,a“critical scale”of learning ability exists to promote the formation of leading technology:a large number of adopting users can promote the dominant technology’s formation by influencing the adaptive response of technology standards to the socio-technical landscape and the choice of technology standards by the socio-technical landscape.There is a minimum threshold and a maximum threshold for the role of adaptability in the dominant technology’s formation.(iv)The socio-technical landscape can promote the leading technology’s shaping in the high-tech industry,and different elements have different effects.This study promotes research on the formation mechanism of dominant technology in the high-tech industry,presents new perspectives and methods for researchers,and provides essential enlightenment for managers to formulate technology strategies.
基金This research has been conducted under SEGTRANS project,funded by the Centre for Industrial Technological Development(CDTI,Government of Spain).
文摘This paper explores the performances of a finite element simulation including four concrete models applied to a full-scale reinforced concrete beam subjected to blast loading. Field test data has been used to compare model results for each case. The numerical modelling has been, carried out using the suitable code LS-DYNA. This code integrates blast load routine(CONWEP) for the explosive description and four different material models for the concrete including: Karagozian & Case Concrete, Winfrith, Continuous Surface Cap Model and Riedel-Hiermaier-Thoma models, with concrete meshing based on 10, 15, and 20 mm. Six full-scale beams were tested: four of them used for the initial calibration of the numerical model and two more tests at lower scaled distances. For calibration, field data obtained employing pressure and accelerometers transducers were compared with the results derived from the numerical simulation. Damage surfaces and the shape of rupture in the beams have been used as references for comparison. Influence of the meshing on accelerations has been put in evidence and for some models the shape and size of the damage in the beams produced maximum differences around 15%. In all cases, the variations between material and mesh models are shown and discussed.
基金supported by the National Natural Science Foundation of China(41927801).
文摘To address the current problems of poor generality,low real-time,and imperfect information transmission of the battlefield target intelligence system,this paper studies the battlefield target intelligence system from the top-level perspective of multi-service joint warfare.First,an overall planning and analysis method of architecture modeling is proposed with the idea of a bionic analogy for battlefield target intelligence system architecture modeling,which reduces the difficulty of the planning and design process.The method introduces the Department of Defense architecture framework(DoDAF)modeling method,the multi-living agent(MLA)theory modeling method,and other combinations for planning and modeling.A set of rapid planning methods that can be applied to model the architecture of various types of complex systems is formed.Further,the liveness analysis of the battlefield target intelligence system is carried out,and the problems of the existing system are presented from several aspects.And the technical prediction of the development and construction is given,which provides directional ideas for the subsequent research and development of the battlefield target intelligence system.In the end,the proposed architecture model of the battlefield target intelligence system is simulated and verified by applying the colored Petri nets(CPN)simulation software.The analysis demonstrates the reasonable integrity of its logic.
基金the Natural Science Foundation of Jiangsu Province(Grant No.BK20200494)China Postdoctoral Science Foundation(Grant No.2021M701725)+3 种基金Jiangsu Postdoctoral Research Funding Program(Grant No.2021K522C)Fundamental Research Funds for the Central Universities(Grant No.30919011246)National Natural Science Foundation of China(Grant No.52278188)Natural Science Foundation of Jiangsu Province(Grant No.BK20211196)。
文摘To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.
基金Supported by the National Natural Science Foundation of China(42221002,42171432)Shanghai Municipal Science and Technology Major Project(2021SHZDZX0100)the Fundamental Research Funds for the Central Universities.
文摘The geometric accuracy of topographic mapping with high-resolution remote sensing images is inevita-bly affected by the orbiter attitude jitter.Therefore,it is necessary to conduct preliminary research on the stereo mapping camera equipped on lunar orbiter before launching.In this work,an imaging simulation method consid-ering the attitude jitter is presented.The impact analysis of different attitude jitter on terrain undulation is conduct-ed by simulating jitter at three attitude angles,respectively.The proposed simulation method is based on the rigor-ous sensor model,using the lunar digital elevation model(DEM)and orthoimage as reference data.The orbit and attitude of the lunar stereo mapping camera are simulated while considering the attitude jitter.Two-dimensional simulated stereo images are generated according to the position and attitude of the orbiter in a given orbit.Experi-mental analyses were conducted by the DEM with the simulated stereo image.The simulation imaging results demonstrate that the proposed method can ensure imaging efficiency without losing the accuracy of topographic mapping.The effect of attitude jitter on the stereo mapping accuracy of the simulated images was analyzed through a DEM comparison.
基金supported by the National Natural Science Foundation of China(62231001).
文摘The parametric scattering center model of radar tar-get has the advantages of simplicity,sparsity and mechanism relevant,making it widely applied in fields such as radar data compression and rapid generation,radar imaging,feature extraction and recognition.This paper summarizes and analyzes the research situation,development trend,and difficult prob-lems on scattering center(SC)parametric modeling from three aspects:parametric representation,determination method of model parameters,and application.
基金Project(DY105 03 02 1) supported by the Deep Ocean Technology Development Itemproject(50474052) supportedby the National Natural Science Foundation of China
文摘According to the characteristics of spiral mining head for deep seabed cobalt-rich crust, the kinematic model, cutting loads model, quantity of cutting picks model of mining head, granularity distribution model and energy consumption model were constructed. Based on these models, computer simulation program of cutting loads was developed with VB software. The mechanical parameters of mining head were obtained in the cutting depth range of 5160 mm. Making use of the simulation results, the effect of cutting depth of spiral mining head on the mining process was studied. The results show that the maximum force of single pick is 4.7051kN, the maximum force and torque of spiral drum of mining head are respectively 34.1668kN and 3.8795kN·m at the cutting depth of 160mm.
文摘OBJECTIVE To explain the high inter-individual variability and the frequency of exceeding the therapeutic reference range and the laboratory alert level of amisulpride,a popula⁃tion pharmacokinetic model in Chinese patients with schizophrenia was built based on therapeu⁃tic drug monitoring data to guide individualized therapy.METHODS Plasma concentration data(330 measurements from 121 patients)were ana⁃lyzed using a nonlinear mixed-effects model⁃ing approach with first-order conditional estima⁃tion with interaction(FOCE I).The concentra⁃tions of amisulpride were detected by HPLC-MS/MS.Age,weight,sex,combination medication history and renal function status were evaluated as main covariates.The model was internally val⁃idated using goodness-of-fit,bootstrap and nor⁃malized prediction distribution error.Recom⁃mended dosage regimens for patients with key covariates were estimated on the basis of Monte Carlo simulations and the established model.RESULTS A one-compartment model with first-order absorption and elimination was found to adequately characterize amisulpride concentra⁃tion in Chinese patients with schizophrenia.The population estimates of the apparent volume of distribution(V/F)and apparent clearance(CL/F)were 12.7 L and 1.12 L·h-1,respectively.Age sig⁃nificantly affected the clearance of amisulpride and the final model was as follow:CL/F=1.04×(AGE/32)-0.624(L·h-1).To avoid exceeding the lab⁃oratory alert level(640μg·L-1),the model-based simulation results showed that the recommended dose of amisulpride was no more than 600 mg per day for patients aged 60 years,800 mg per day for those aged 40 years and 1200 mg per day for those aged 20 years,respectively.CON⁃CLUSION Dosage optimization of amisulpride can be carried out according to age to reduce the risk of adverse reactions.The model can be used as a suitable tool for designing individual⁃ized therapy for Chinese patients with schizo⁃phrenia.
文摘基于中国科学院自主研发的第二代地球系统模式CAS-ESM2.0,本研究通过在陆面分量模式CoLM(Common Land Model)中引入植被水力模型以替换原有的经验性方案,开展了两组34年(1981~2014年)的AMIP(Atmospheric Model Intercomparison Project)数值模拟试验,探讨了植被水力方案的引入对中国夏季降水模拟的影响。结果表明,植被水力方案的引入能够显著降低CAS-ESM2.0模式对中国夏季降水气候态的模拟偏差,特别是显著改进了中国东部、青藏高原降水的低估,青藏高原以东的川西地区降水高估的偏差,同时也改善了夏季降水年际变率和极端大雨日数的模拟性能。进一步分析显示,植被水力方案的改进显著减小了土壤湿度在长江流域偏干、青藏高原偏湿的模式模拟偏差,降低了我国中东部以及青藏高原地表感热通量和潜热通量的模拟偏差,改善了模式对陆气相互作用过程的模拟能力。陆气相互作用的改进显著提升了模式对东亚季风环流的模拟,改进后的模式模拟的西北太平洋海平面气压的负偏差显著降低,有利于西南季风以及西北太平洋向我国东部的水汽输送,同时在对流层低层出现反气旋异常响应,有效改善了中国东部南风偏弱及水汽辐合偏弱的模拟偏差,使得我国东部降水负偏差显著减小。以上结果表明,包括植被水力过程的陆气相互作用的合理表述是改善东亚夏季降水模拟的重要途径之一。
基金supported by Scientific Research Program Funded by Shaanxi Provincial Education Department(Program No.18JK0286)Weinan Science and Technology Initiatives Fund program(Program No.2019JCYJ-2-6)+2 种基金Teaching Reform Project of Weinan Normal University(Program No.JG201704)Industry-University-Cooperation Education Project of the Ministry of Education of China(Program No.201702030020,201801082110)Weinan Normal University's Characteristic Discipline Construction Project Electronic Information(Computer Technology)Master's Degree Point Construction Project(18TSXK06)。
文摘In this paper,we proposed a new design scheme of real time electronic countermeasure simulation system.This paper mainly expounds the modeling and realization methods of each part of the whole simulation system,and the real-time property of system has been lucubrated.Electronic countermeasure simulation system is the key part of military training of individuals;it can also allow the realistic evaluation of the performance of modern equipments and techniques.As a proof,we have drawn up a series of simulation scenarios,such as radar electronic reconnaissance simulation scenario,to explain the feasibility and the superiority of our modeling scheme in this paper.
基金Project(2008ZHZX1A0502) supported by the Independence Innovation Achievements Transformation Crucial Special Program of Shandong Province,China
文摘A multi-domain nonlinear dynamic model of a proportional solenoid valve was presented.The electro-magnetic,mechanical and fluid subsystems of the valve were investigated,including their interactions.Governing equations of the valve were derived in the form of nonlinear state equations.By comparing the simulated and measured data,the simulation model is validated with a deviation less than 15%,which can be used for the structural design and control algorithm optimization of proportional solenoid valves.
基金Projects(60404003,11202230)supported by the National Natural Science Foundation of China
文摘The application of new-designed levitation controller requires extensive validation prior to enter into commercial service. However, huge mounts of approximations and assumptions lead the theoretical analysis away from the engineering practice. The experimental methods are time-consuming and financial expensive, even unrealizable due to the lack of suitable sensors. Numerical simulations can bridge the gap between the theoretical analysis and experimental techniques. A complete overall dynamic model of maglev levitation system is derived in this work, which includes the simple-supported bridges, the calculation of electromagnetic force with more details, the stress of levitation modules and the cabin. Based on the aforementioned model, it shows that the inherent nonlinearity, inner coupling, misalignments between the sensors and actuators, and self-excited vibration are the main issues that should be considered during the design process of controller. Then, the backstepping controller based on the mathematical model of the module with reasonable simplifications is proposed, and the stability proofs are listed. To show the advantage of controller, two numerical simulation experiments are carried out. Finally, the results illustrating closed-loop performance are provided.
基金supported by the National Key Research and Development Program of China(61873236)the Natural Science Foundation of Zhejiang Province(LZ21F020003,LY18F030001)the Civil Aerospace Pre-research Project(D020101).
文摘A system of systems(SoS)composes a set of independent constituent systems(CSs),where the degree of authority to control the independence of CSs varies,depending on different SoS types.Key researchers describe four SoS types with descending levels of central authority:directed,acknowledged,collaborative and virtual.Although the definitions have been recognized in SoS engineering,what is challenging is the difficulty of translating these definitions into models and simulation environments.Thus,we provide a goal-based method including a mathematical baseline to translate these definitions into more effective agent-based modeling and simulations.First,we construct the theoretical models of CS and SoS.Based on the theoretical models,we analyze the degree of authority influenced by SoS characteristics.Next,we propose a definition of SoS types by quantitatively explaining the degree of authority.Finally,we recognize the differences between acknowledged SoS and collaborative SoS using a migrating waterfowl flock by an agentbased model(ABM)simulation.This paper contributes to the SoS body of knowledge by increasing our understanding of the degree of authority in an SoS,so we may identify suitable SoS types to achieve SoS goals by modeling and simulation.
