The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nit...The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nitrogen-doped carbon fibers loaded with a ternary metal sulf-ide((Fe,Co,Ni)_(9)S_(8))for use as the sulfur host in Li-S batteries.This materi-al was prepared using transfer blot filter paper as the carbon precursor,thiourea as the source of nitrogen and sulfur,and FeCl_(3)·6H_(2)O,CoCl_(2)·6H_(2)O and NiCl_(2)·6H_(2)O as the metal ion sources.It was synthesized by an impreg-nation method followed by calcination.The nitrogen doping significantly in-creased the conductivity of the host,and the metal sulfides have excellent catalytic activities.Theoretical calculations,and adsorption and deposition experiments show that active sites on the surface of FCNS@NCFs selectively adsorb polysulfides,facilitate rapid adsorption and conversion,prevent cathode passivation and inhib-it the polysulfide shuttling.The FCNS@NCFs used as the sulfur host has excellent electrochemical properties.Its initial dis-charge capacity is 1639.0 mAh g^(−1) at 0.2 C and room temperature,and it remains a capacity of 1255.1 mAh g^(−1) after 100 cycles.At−20~C,it has an initial discharge capacity of 1578.5 mAh g^(−1) at 0.2 C,with a capacity of 867.5 mAh g^(−1) after 100 cycles.Its excellent performance at both ambient and low temperatures suggests a new way to produce high-performance low-temper-ature Li-S batteries.展开更多
ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(...ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(2)-Nb_(2)O_(5)(CTN)ternary composite oxide additives with different composition ratios on sintering behavior and properties of ZnAl_(2)O_(4) microwave dielectric ceramics was investigated.When the molar fraction ranges of Cu,Ti and Nb elements in 5%CTN additives are 0.625-0.875,0-0.250 and 0.125-0.625,respectively,sintering temperature of ZnAl_(2)O_(4) ceramics can be reduced from above 1400℃to below 1000℃.The sintering additives CN(Cu:Nb=1:1,molar ratio)and CTN(Cu:Ti:Nb=4:1:3,molar ratio)can reduce sintering temperature of ZnAl_(2)O_(4) ceramics to 975 and 1000℃,respectively,while maintaining good dielectric properties(dielectric constantε_(r)=11.36,quality factor Q׃=8245 GHz andε_(r)=9.52,Q׃=22249 GHz)and flexural strengths(200 and 161 MPa),which are expected to be applied in preparation of low temperature co-fired ceramic(LTCC)materials with copper electrodes.Low-temperature sintering of the ZnAl_(2)O_(4)+CTN system is characterized as activated sintering.Nanometer-level amorphous interfacial films containing Cu,Ti,and Nb elements are observed at the grain boundaries,which may provide fast diffusion pathways for mass transportation during the sintering process.Valence changes of Ti and Cu ions,along with changes of oxygen vacancies,are confirmed,which provides a potential mechanism for reduced sintering temperature of ZnAl_(2)O_(4) ceramics.In addition,a series of reactions occurring at the grain boundaries can activate these boundaries and further promote the sintering densification process.These results suggest a promising way to design a novel LTCC material with excellent properties based on the low temperature sintering of ceramics with the sintering aid of CuO-TiO_(2)-Nb_(2)O_(5) composite oxide.展开更多
The new technology of direct decomposition of H_(2)S into high value-added H_(2) and S,as an alternative to the Claus process in industry,is an ideal route that can not only deal with toxic and abundant H_(2)S waste g...The new technology of direct decomposition of H_(2)S into high value-added H_(2) and S,as an alternative to the Claus process in industry,is an ideal route that can not only deal with toxic and abundant H_(2)S waste gas but also recover clean energy H_(2),which has significant socio-economic and ecological advantages.However,the highly effective decomposition of H_(2)S at low temperatures is still a great challenge,because of the stringent thermodynamic equilibrium constraints(only 20% even at high temperature of 1010℃).Conventional microwave catalysts exhibit unsatisfactory performance at low temperatures(below 600℃).Herein,Mo_(2)C@CeO_(2) catalysts with a core-shell structure were successfully developed for robust microwave catalytic decomposition of H_(2)S at low temperatures.Two carbon precursors,para-phenylenediamine(Mo_(2)C-p)and meta-phenylenediamine(Mo_(2)C-m),were employed to tailor Mo_(2)C configurations.Remarkably,the H_(2)S conversion of Mo_(2)C-p@CeO_(2) catalyst at a low temperature of 550℃ is as high as 92.1%,which is much higher than the H_(2)S equilibrium conversion under the conventional thermal conditions(2.6% at 550℃).To our knowledge,this represents the most active catalyst for microwave catalytic decomposition of H_(2)S at low temperature of 550℃.Notably,Mo_(2)C-p demonstrated superior intrinsic activity(84%)compared to Mo_(2)C-m(6.4%),with XPS analysis revealing that its enhanced performance stems from a higher concentration of Mo_(2+)active sites.This work presents a substitute approach for the efficient utilization of H_(2)S waste gas and opens up a novel avenue for the rational design of microwave catalysts for microwave catalytic reaction at low-temperature.展开更多
The reduced ability of fatty acids to dissolve and disperse at low temperatures limits their effectiveness in winter applications.In this study,a green and environment-friendly reagent,polyethylene glycol 2000(PEG-200...The reduced ability of fatty acids to dissolve and disperse at low temperatures limits their effectiveness in winter applications.In this study,a green and environment-friendly reagent,polyethylene glycol 2000(PEG-2000),was used to evaluate its effect on the collecting performance of sodium oleate during scheelite flotation at low temperatures.The effect of PEG-2000 on the flotation of scheelite with the collector sodium oleate(NaOL)was studied by flotation tests,surface tension tests,infrared spectral analysis,and zeta potential measurements.Flotation tests showed that adding PEG-2000 can enhance the collecting ability of NaOL on scheelite at low temperature(5℃).The recovery of scheelite with the mixed collector of PEG-200 and NaOL is 4.39%higher than that with NaOL only.The surface tension tests,infrared spectral analysis and zeta potential measurements revealed that PEG-2000 and OL^(−)are co-adsorbed on the scheelite surface at low temperatures.The presence of PEG-2000 promoted the increase of the adsorption concentration of oleate ions(OL^(−))on the scheelite surface.The reason was that PEG-2000 has a shielding effect on the electrostatic repulsion between the OL^(−)groups,which changes the micellar configuration of OL^(−)in the solution system and makes the OL^(−)gather more tightly on the surface of scheelite,leading to the enhancement of its hydrophobicity.This discovery provides a reference for the development of collecting reagents for efficient flotation recovery of scheelite under low temperature environment.展开更多
The effects of heat treatment on the microstructure and mechanical properties of two alloys, namely Al-12.2%Zn-2.48%Cu-2.0%Mg-0.15%Zr-0.166%Ag（alloy 1）, and Al-9.99%Zn-1.72%Cu-2.5%Mg- 0.13%Zr （alloy 2） were invest...The effects of heat treatment on the microstructure and mechanical properties of two alloys, namely Al-12.2%Zn-2.48%Cu-2.0%Mg-0.15%Zr-0.166%Ag（alloy 1）, and Al-9.99%Zn-1.72%Cu-2.5%Mg- 0.13%Zr （alloy 2） were investigated. The results show that low temperature aging after promotive solution treatment can increase elongation without the loss of strength for the studied alloys. The optimum aging treatment （T6） for alloy 1 and alloy 2 is 100℃/80h and 100℃/48h, respectively. Compared with other heat treatment alloys, alloy 1 and alloy 2 show super-high tensile strength up to 753MPa and 788MPa, remaining 9.3% and 9.7% elongation under T6 condition, respectively. During aging, trace addition of Ag enhances the formations of GP zone and metastable phase, and stabilizes GP zone and metastable phase to a higher temperature. Trace addition of Ag prolongs the aging time of reaching the peak strength and delays over-aging condition of the alloy. However, trace addition of Ag promotes the formation of coarse constituent in the alloy and consumes hardening alloying elements of Zn and Mg. Moreover, the addition of the transition element Zr in 7000 series super-high alloy forms incoherent Al3Zr dispersoid which can serve as nucleation sites for nonuniform precipitation of η phase during aging process. The higher the aging temperature, the greater the tendency for nonuniform precipitation of η phase.展开更多
The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron m...The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results confirm that the strength of TC4 alloy can be improved obviously by LTTMT processing, which combines strain strengthening with aging strengthening. The effect of LTTMT on the alloy depends on the microstructure of the refined and dispersed a＋fl phase on the basis of high dislocation density by pre-deformation below recrystallization temperature. The tensile strength decreases with the increase of pre-deformation reduction. The optimal processing parameters of LTTMT for TC4 alloy are as follows： solution treatment at 900 ℃ for 15 min, pre-deformation in the range of 600-700 ℃ with a reduction of 35%, finally aging at 540 ℃ for 4 h followed by air-cooling.展开更多
The precursor of ammonium aluminum carbonate hydroxide was synthesized by using aluminum sulfate（Al2（SO4）3） and ammonium carbonate（（NH4）2CO3）. The effects of α-Al2O3 seeds and mixture composed of α-Al2O3 and...The precursor of ammonium aluminum carbonate hydroxide was synthesized by using aluminum sulfate（Al2（SO4）3） and ammonium carbonate（（NH4）2CO3）. The effects of α-Al2O3 seeds and mixture composed of α-Al2O3 and ammonium nitrate, as well as multiplex catalysts （AT） on phase transformation of alumina in sintering process were investigated respectively. The results show that the α-Al2O3 seeds and the mixture of α-Al2O3 and ammonium nitrate can lower the phase transformation temperature of α-Al2O3 to different extents while the particles obtained agglomerate heavily. AT has great potential synergistic effects on the phase transformation of alumina and reduces the phase transformation temperature of α-Al2O3 and the trends of necking-formation between particles. Therefore the dispersion of powder particles is improved significantly.展开更多
A process was proposed to convert and separate selenium and arsenic in copper anode slime(CAS) by low-temperature alkali fusion process.Central composite design was employed to optimize the effective parameters,in whi...A process was proposed to convert and separate selenium and arsenic in copper anode slime(CAS) by low-temperature alkali fusion process.Central composite design was employed to optimize the effective parameters,in which Na OH/CAS mass ratio,fusion temperature and fusion time were selected as variables,and the conversion ratio of selenium and arsenic as responses.Second-order polynomial models of high significance and 3D response surface plots were constructed to show the relationship between the responses and the variables.Optimum area of >90% selenium conversion ratio and >90% arsenic conversion ratio was obtained by the overlaid contours at Na OH/CAS mass ratio of 0.65-0.75,fusion temperature of 803-823 K and fusion time of 20-30 min.The models are validated by experiments in the optimum area,and the results demonstrate that these models are reliable and accurate in predicting the fusion process.展开更多
Three varieties were employed as materials to study changes of photosynthetic traits under low-temperature stress. The results showed that Pn, Gs and Tr decreased under low-temperature treatment. Ci decreased under lo...Three varieties were employed as materials to study changes of photosynthetic traits under low-temperature stress. The results showed that Pn, Gs and Tr decreased under low-temperature treatment. Ci decreased under low-temperature treatment 18℃/ 9℃, and 16℃/7℃, and it decreased in earlier stage after increased under 14℃/5℃. WUE was increased in earlier stage and after stabilized. The order of the three varieties of cold resistance were Jinyu 5〉Xingken 3〉Jidan 198. They could make self-regulation through adjusting Gs, Tr, Ci and WUE.展开更多
In order to investigate the physiological injury of barley caused by the low temperature after herbicides, tillering barley seedlings planted in plastic cups were pretreated in illumination incubator at 15℃ and 12 h-...In order to investigate the physiological injury of barley caused by the low temperature after herbicides, tillering barley seedlings planted in plastic cups were pretreated in illumination incubator at 15℃ and 12 h-light per day for 7 days, and then subjected to herbicide treatment, prometryn （with the concentrations of 0, 0.15%, 0.30%, and 0.45%） or isoproturon （with the concentrations of 0, 0.30%, 0.60%, and 0.90%）, and the SOD activity, the CAT activity, the POD activity, the MDA content, proline content, soluble protein content, electrical conductivity, and the rate of O2 were determined and analyzed. The results showed that the low-temperature was the most important, and the treatment-time of low-temperature was another significant influencing factor on the physiological and biochemical indices of barley seedlings. However, all of the physiological and biochemical indices determined were not affected by the kinds of herbicides and herbicide concentrations, and the SOD was stable and should play the more prominent role on extracting of free radicals according to the stepwise regression and correlation. The herbicide concentrations should be increased in the future research for truly reflecting the effects of the herbicide concentration on the physiological and biochemical indices of barley seedlings.展开更多
A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used t...A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.展开更多
A series of transition metal Mn,Cu,Ce and Fe were loaded on TiO_(2) by sol-gel method with noble metal Pd as promotor for the application of passive NO_(x) absorber.Experiments on adsorption and desorption of NO_(x) w...A series of transition metal Mn,Cu,Ce and Fe were loaded on TiO_(2) by sol-gel method with noble metal Pd as promotor for the application of passive NO_(x) absorber.Experiments on adsorption and desorption of NO_(x) were conducted and characterization methods such as X-ray diffraction(XRD),X-ray photoelectron spectroscopy(XPS),transmission electron microscopy(TEM)and in situ Fourier transform infrared spectroscopy(in situ DRIFTS)were involved.The experimental results show that Mn-contained catalysts,Mn-Ti and Pd-Mn-Ti,performed excellent NO_(x) adsorbing ability and appropriate desorption temperature window.On the other hand,Ce-and Cu-contained samples were not suitable for the purpose of PNA.In addition to the low adsorption capacity,these two series of catalysts released massive amount of NO below 150℃.Characterization results indicated that Pd was highly dispersed on all catalysts.The loading of Pd lowered not only the valence states of transition metals but surface oxygen percentage as well.From in situ DRIFTS tests,the Pd had little influence on the types of adsorbed substances for Mn,Ce and Cu series.However,the storage forms of NO_(x) were obviously different on Pd-Fe-Ti and Fe-Ti.展开更多
In order to reduce powder temperature to lower than 100℃ in warm compaction by changing polymer lubricant design, powder flowability, warm compacting behavior, lubricating mode as well as ultimate tensile strength af...In order to reduce powder temperature to lower than 100℃ in warm compaction by changing polymer lubricant design, powder flowability, warm compacting behavior, lubricating mode as well as ultimate tensile strength after sinter-hardening and tempering were investigated systematically. By means of low temperature warm pressing and sintered hardening technique, samples with the sintered densities of 7.407.45g/cm3 and the strengths of 950 1390MPa are achieved as the early compacting pressure is 686735MPa.展开更多
It is well known that β-BBO is a new type nonlinear optical crystal discovered in our institute and now β-BBO is widely used in the fields of laser and nonlinear optics. However, there are still some inclusions in ...It is well known that β-BBO is a new type nonlinear optical crystal discovered in our institute and now β-BBO is widely used in the fields of laser and nonlinear optics. However, there are still some inclusions in β-BBO crystal grown by flux method. Using AEM technique, we have studied the shape, composition and structure of inclusions which is very helpful to the explanation of the formation of inclusions.展开更多
基金partially supported by National Natural Science Foundation of China(52172250)Institute of Process Engineering(IPE)Project for Frontier Basic Research(QYJC-2023-06)。
文摘The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nitrogen-doped carbon fibers loaded with a ternary metal sulf-ide((Fe,Co,Ni)_(9)S_(8))for use as the sulfur host in Li-S batteries.This materi-al was prepared using transfer blot filter paper as the carbon precursor,thiourea as the source of nitrogen and sulfur,and FeCl_(3)·6H_(2)O,CoCl_(2)·6H_(2)O and NiCl_(2)·6H_(2)O as the metal ion sources.It was synthesized by an impreg-nation method followed by calcination.The nitrogen doping significantly in-creased the conductivity of the host,and the metal sulfides have excellent catalytic activities.Theoretical calculations,and adsorption and deposition experiments show that active sites on the surface of FCNS@NCFs selectively adsorb polysulfides,facilitate rapid adsorption and conversion,prevent cathode passivation and inhib-it the polysulfide shuttling.The FCNS@NCFs used as the sulfur host has excellent electrochemical properties.Its initial dis-charge capacity is 1639.0 mAh g^(−1) at 0.2 C and room temperature,and it remains a capacity of 1255.1 mAh g^(−1) after 100 cycles.At−20~C,it has an initial discharge capacity of 1578.5 mAh g^(−1) at 0.2 C,with a capacity of 867.5 mAh g^(−1) after 100 cycles.Its excellent performance at both ambient and low temperatures suggests a new way to produce high-performance low-temper-ature Li-S batteries.
基金National Natural Science Foundation of China (U24A2052)Shanghai Eastern Talent Plan。
文摘ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(2)-Nb_(2)O_(5)(CTN)ternary composite oxide additives with different composition ratios on sintering behavior and properties of ZnAl_(2)O_(4) microwave dielectric ceramics was investigated.When the molar fraction ranges of Cu,Ti and Nb elements in 5%CTN additives are 0.625-0.875,0-0.250 and 0.125-0.625,respectively,sintering temperature of ZnAl_(2)O_(4) ceramics can be reduced from above 1400℃to below 1000℃.The sintering additives CN(Cu:Nb=1:1,molar ratio)and CTN(Cu:Ti:Nb=4:1:3,molar ratio)can reduce sintering temperature of ZnAl_(2)O_(4) ceramics to 975 and 1000℃,respectively,while maintaining good dielectric properties(dielectric constantε_(r)=11.36,quality factor Q׃=8245 GHz andε_(r)=9.52,Q׃=22249 GHz)and flexural strengths(200 and 161 MPa),which are expected to be applied in preparation of low temperature co-fired ceramic(LTCC)materials with copper electrodes.Low-temperature sintering of the ZnAl_(2)O_(4)+CTN system is characterized as activated sintering.Nanometer-level amorphous interfacial films containing Cu,Ti,and Nb elements are observed at the grain boundaries,which may provide fast diffusion pathways for mass transportation during the sintering process.Valence changes of Ti and Cu ions,along with changes of oxygen vacancies,are confirmed,which provides a potential mechanism for reduced sintering temperature of ZnAl_(2)O_(4) ceramics.In addition,a series of reactions occurring at the grain boundaries can activate these boundaries and further promote the sintering densification process.These results suggest a promising way to design a novel LTCC material with excellent properties based on the low temperature sintering of ceramics with the sintering aid of CuO-TiO_(2)-Nb_(2)O_(5) composite oxide.
基金supported by the National Natural Science Foundation of China(22178295,21706225)Natural Science Foundation of Hunan Province(2025JJ50085)Hunan Collaborative Innovation Center of New Chemical Technologies for Environmental Benignity and Efficient Resource Utilization.
文摘The new technology of direct decomposition of H_(2)S into high value-added H_(2) and S,as an alternative to the Claus process in industry,is an ideal route that can not only deal with toxic and abundant H_(2)S waste gas but also recover clean energy H_(2),which has significant socio-economic and ecological advantages.However,the highly effective decomposition of H_(2)S at low temperatures is still a great challenge,because of the stringent thermodynamic equilibrium constraints(only 20% even at high temperature of 1010℃).Conventional microwave catalysts exhibit unsatisfactory performance at low temperatures(below 600℃).Herein,Mo_(2)C@CeO_(2) catalysts with a core-shell structure were successfully developed for robust microwave catalytic decomposition of H_(2)S at low temperatures.Two carbon precursors,para-phenylenediamine(Mo_(2)C-p)and meta-phenylenediamine(Mo_(2)C-m),were employed to tailor Mo_(2)C configurations.Remarkably,the H_(2)S conversion of Mo_(2)C-p@CeO_(2) catalyst at a low temperature of 550℃ is as high as 92.1%,which is much higher than the H_(2)S equilibrium conversion under the conventional thermal conditions(2.6% at 550℃).To our knowledge,this represents the most active catalyst for microwave catalytic decomposition of H_(2)S at low temperature of 550℃.Notably,Mo_(2)C-p demonstrated superior intrinsic activity(84%)compared to Mo_(2)C-m(6.4%),with XPS analysis revealing that its enhanced performance stems from a higher concentration of Mo_(2+)active sites.This work presents a substitute approach for the efficient utilization of H_(2)S waste gas and opens up a novel avenue for the rational design of microwave catalysts for microwave catalytic reaction at low-temperature.
基金Project(2023JJ10070)supported by the Hunan Provincial Outstanding Youth Fund,ChinaProjects(51974364,52074355,52304316)supported by the National Natural Science Foundation of China。
文摘The reduced ability of fatty acids to dissolve and disperse at low temperatures limits their effectiveness in winter applications.In this study,a green and environment-friendly reagent,polyethylene glycol 2000(PEG-2000),was used to evaluate its effect on the collecting performance of sodium oleate during scheelite flotation at low temperatures.The effect of PEG-2000 on the flotation of scheelite with the collector sodium oleate(NaOL)was studied by flotation tests,surface tension tests,infrared spectral analysis,and zeta potential measurements.Flotation tests showed that adding PEG-2000 can enhance the collecting ability of NaOL on scheelite at low temperature(5℃).The recovery of scheelite with the mixed collector of PEG-200 and NaOL is 4.39%higher than that with NaOL only.The surface tension tests,infrared spectral analysis and zeta potential measurements revealed that PEG-2000 and OL^(−)are co-adsorbed on the scheelite surface at low temperatures.The presence of PEG-2000 promoted the increase of the adsorption concentration of oleate ions(OL^(−))on the scheelite surface.The reason was that PEG-2000 has a shielding effect on the electrostatic repulsion between the OL^(−)groups,which changes the micellar configuration of OL^(−)in the solution system and makes the OL^(−)gather more tightly on the surface of scheelite,leading to the enhancement of its hydrophobicity.This discovery provides a reference for the development of collecting reagents for efficient flotation recovery of scheelite under low temperature environment.
基金Project (2001AA332030) supported by the National High Technology Research and Development Programof China
文摘The effects of heat treatment on the microstructure and mechanical properties of two alloys, namely Al-12.2%Zn-2.48%Cu-2.0%Mg-0.15%Zr-0.166%Ag（alloy 1）, and Al-9.99%Zn-1.72%Cu-2.5%Mg- 0.13%Zr （alloy 2） were investigated. The results show that low temperature aging after promotive solution treatment can increase elongation without the loss of strength for the studied alloys. The optimum aging treatment （T6） for alloy 1 and alloy 2 is 100℃/80h and 100℃/48h, respectively. Compared with other heat treatment alloys, alloy 1 and alloy 2 show super-high tensile strength up to 753MPa and 788MPa, remaining 9.3% and 9.7% elongation under T6 condition, respectively. During aging, trace addition of Ag enhances the formations of GP zone and metastable phase, and stabilizes GP zone and metastable phase to a higher temperature. Trace addition of Ag prolongs the aging time of reaching the peak strength and delays over-aging condition of the alloy. However, trace addition of Ag promotes the formation of coarse constituent in the alloy and consumes hardening alloying elements of Zn and Mg. Moreover, the addition of the transition element Zr in 7000 series super-high alloy forms incoherent Al3Zr dispersoid which can serve as nucleation sites for nonuniform precipitation of η phase during aging process. The higher the aging temperature, the greater the tendency for nonuniform precipitation of η phase.
基金Project(2008WK2005) supported by the Science and Technology Plan of Hunan Province, China
文摘The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results confirm that the strength of TC4 alloy can be improved obviously by LTTMT processing, which combines strain strengthening with aging strengthening. The effect of LTTMT on the alloy depends on the microstructure of the refined and dispersed a＋fl phase on the basis of high dislocation density by pre-deformation below recrystallization temperature. The tensile strength decreases with the increase of pre-deformation reduction. The optimal processing parameters of LTTMT for TC4 alloy are as follows： solution treatment at 900 ℃ for 15 min, pre-deformation in the range of 600-700 ℃ with a reduction of 35%, finally aging at 540 ℃ for 4 h followed by air-cooling.
文摘The precursor of ammonium aluminum carbonate hydroxide was synthesized by using aluminum sulfate（Al2（SO4）3） and ammonium carbonate（（NH4）2CO3）. The effects of α-Al2O3 seeds and mixture composed of α-Al2O3 and ammonium nitrate, as well as multiplex catalysts （AT） on phase transformation of alumina in sintering process were investigated respectively. The results show that the α-Al2O3 seeds and the mixture of α-Al2O3 and ammonium nitrate can lower the phase transformation temperature of α-Al2O3 to different extents while the particles obtained agglomerate heavily. AT has great potential synergistic effects on the phase transformation of alumina and reduces the phase transformation temperature of α-Al2O3 and the trends of necking-formation between particles. Therefore the dispersion of powder particles is improved significantly.
基金Project(51234009)supported by the National Natural Science Foundation of ChinaProject(2014DFA90520)supported by International Cooperation Program of Ministry of Science of ChinaProject(2013A100003)supported by the Production,Teaching and Research Program of Guangdong Province,China
文摘A process was proposed to convert and separate selenium and arsenic in copper anode slime(CAS) by low-temperature alkali fusion process.Central composite design was employed to optimize the effective parameters,in which Na OH/CAS mass ratio,fusion temperature and fusion time were selected as variables,and the conversion ratio of selenium and arsenic as responses.Second-order polynomial models of high significance and 3D response surface plots were constructed to show the relationship between the responses and the variables.Optimum area of >90% selenium conversion ratio and >90% arsenic conversion ratio was obtained by the overlaid contours at Na OH/CAS mass ratio of 0.65-0.75,fusion temperature of 803-823 K and fusion time of 20-30 min.The models are validated by experiments in the optimum area,and the results demonstrate that these models are reliable and accurate in predicting the fusion process.
基金Supported by the Science and Technology Foundation(2008BADB3B09-03)
文摘Three varieties were employed as materials to study changes of photosynthetic traits under low-temperature stress. The results showed that Pn, Gs and Tr decreased under low-temperature treatment. Ci decreased under low-temperature treatment 18℃/ 9℃, and 16℃/7℃, and it decreased in earlier stage after increased under 14℃/5℃. WUE was increased in earlier stage and after stabilized. The order of the three varieties of cold resistance were Jinyu 5〉Xingken 3〉Jidan 198. They could make self-regulation through adjusting Gs, Tr, Ci and WUE.
基金Supported by the National Natural Science Foundation of China (31000712)
文摘In order to investigate the physiological injury of barley caused by the low temperature after herbicides, tillering barley seedlings planted in plastic cups were pretreated in illumination incubator at 15℃ and 12 h-light per day for 7 days, and then subjected to herbicide treatment, prometryn （with the concentrations of 0, 0.15%, 0.30%, and 0.45%） or isoproturon （with the concentrations of 0, 0.30%, 0.60%, and 0.90%）, and the SOD activity, the CAT activity, the POD activity, the MDA content, proline content, soluble protein content, electrical conductivity, and the rate of O2 were determined and analyzed. The results showed that the low-temperature was the most important, and the treatment-time of low-temperature was another significant influencing factor on the physiological and biochemical indices of barley seedlings. However, all of the physiological and biochemical indices determined were not affected by the kinds of herbicides and herbicide concentrations, and the SOD was stable and should play the more prominent role on extracting of free radicals according to the stepwise regression and correlation. The herbicide concentrations should be increased in the future research for truly reflecting the effects of the herbicide concentration on the physiological and biochemical indices of barley seedlings.
基金Projects(51074190,51234009)supported by the National Natural Science Foundation of ChinaProject(2014DFA90520)supported by International Cooperation Program of Ministry of Science of ChinaProject(20110162110049)supported by the Doctoral Scientific Fund Project of the Ministry of Education of China
文摘A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.
基金Project(52106173)supported by the National Natural Science Foundation of ChinaProject(2020TQ0187)supported by the Postdoctoral Research Foundation of China。
文摘A series of transition metal Mn,Cu,Ce and Fe were loaded on TiO_(2) by sol-gel method with noble metal Pd as promotor for the application of passive NO_(x) absorber.Experiments on adsorption and desorption of NO_(x) were conducted and characterization methods such as X-ray diffraction(XRD),X-ray photoelectron spectroscopy(XPS),transmission electron microscopy(TEM)and in situ Fourier transform infrared spectroscopy(in situ DRIFTS)were involved.The experimental results show that Mn-contained catalysts,Mn-Ti and Pd-Mn-Ti,performed excellent NO_(x) adsorbing ability and appropriate desorption temperature window.On the other hand,Ce-and Cu-contained samples were not suitable for the purpose of PNA.In addition to the low adsorption capacity,these two series of catalysts released massive amount of NO below 150℃.Characterization results indicated that Pd was highly dispersed on all catalysts.The loading of Pd lowered not only the valence states of transition metals but surface oxygen percentage as well.From in situ DRIFTS tests,the Pd had little influence on the types of adsorbed substances for Mn,Ce and Cu series.However,the storage forms of NO_(x) were obviously different on Pd-Fe-Ti and Fe-Ti.
文摘In order to reduce powder temperature to lower than 100℃ in warm compaction by changing polymer lubricant design, powder flowability, warm compacting behavior, lubricating mode as well as ultimate tensile strength after sinter-hardening and tempering were investigated systematically. By means of low temperature warm pressing and sintered hardening technique, samples with the sintered densities of 7.407.45g/cm3 and the strengths of 950 1390MPa are achieved as the early compacting pressure is 686735MPa.
文摘It is well known that β-BBO is a new type nonlinear optical crystal discovered in our institute and now β-BBO is widely used in the fields of laser and nonlinear optics. However, there are still some inclusions in β-BBO crystal grown by flux method. Using AEM technique, we have studied the shape, composition and structure of inclusions which is very helpful to the explanation of the formation of inclusions.
