Numerical investigation was performed to examine the effect of rear barrier pillar on stress distribution around a longwall face. Salamon theoretical formula was used to calculate the parameters of the caving zone, wh...Numerical investigation was performed to examine the effect of rear barrier pillar on stress distribution around a longwall face. Salamon theoretical formula was used to calculate the parameters of the caving zone, which was later assigned to double yield constitutive model in FLAC3 D. Numerical results demonstrate that high stress concentration zone exists above the region where the second open-off cut intersects with the rear barrier pillar due to stress transfer and plastic zone expansion. It is also found that the maximum vertical stresses with varied distance to the seam floor are all within the projective plane of the rear barrier pillar and their positions concentrate on the barrier pillar adjacent to the connection corner of the second open-off cut. In addition, position of the maximum vertical stresses abruptly transfer from the connection corner adjacent to former panel to that adjacent to current panel along the panel direction.展开更多
The dynamic response of a multi-cabin protective structure subjected to impact load directly affects the protective performance of materials;thus,studying the dynamic response and communication law of wave effect of t...The dynamic response of a multi-cabin protective structure subjected to impact load directly affects the protective performance of materials;thus,studying the dynamic response and communication law of wave effect of the load plays an important role in the prediction of protective performance.In this study,the protection experiments of box-structure under air-and/or water-medium are conducted,the dynamic response of the structure subjected to low-impact load is analyzed,and the corresponding numerical simulations are analyzed using the theory of finite element method(FEM).Combined with experimental and FEM simulations,the shock strain distribution,acceleration attenuation,and signal energy in defensive materials are determined.Based on the results,the metal structure exhibits good absorption characteristics for shock vibration.Using the experimental data,we also show that the attenuation of shock wave in water medium should be significantly better than that in air medium,and the protective structure should be designed for a combination of water and air mediums.Meanwhile,the numerical simulation can provide a quantitative analysis process for dynamic analysis of defensive materials.展开更多
In order to reveal combustion characteristics of H_2/air mixture in a micro-combustor with and without bluff body, the effects of inlet velocities, equivalence ratios and bluff body's blockage ratios on the temper...In order to reveal combustion characteristics of H_2/air mixture in a micro-combustor with and without bluff body, the effects of inlet velocities, equivalence ratios and bluff body's blockage ratios on the temperature field, pressure of the combustor wall, combustion efficiency and blow-off limit were investigated. The numerical results indicate that the sudden expansion plate micro combustor with bluff body could enhance the turbulent disturbance of the mixed gas in the combustion chamber and the combustion condition is improved. Moreover, a low-speed and high temperature recirculation region was formed between the sudden expansion step and the bluff body so that the high and uniform wall temperature(>1000 K) could be gotten. As a result, it could strengthen the mixing process, prolong the residence time of gas, control the flame position effectively and widen the operation range by the synergistic effect of the bluff body and steps. When the blockage ratio ranged from 0.3 to 0.6, it could be found that the bluff body could play a stabilizing effect and expand combustion blow burning limit, and combustion efficiency firstly was increased with the inlet velocity and equivalence ratio, and then was decreased.展开更多
Joints of copper and stainless steels are used in a er ospace applications. Production of these joints by fusion welding faces many dif ficulties. This may be due to the differences in their physical, metallurgical a ...Joints of copper and stainless steels are used in a er ospace applications. Production of these joints by fusion welding faces many dif ficulties. This may be due to the differences in their physical, metallurgical a nd mechanical properties. Electron Beam Welding (EBW) process has been found to be especially well suited in this area. Selection of the appropriate welding par ameters needs thorough investigations. These parameters include: preheat tempera ture (℃), welding current (I w), focusing current (I F), welding spee d (V), height between the gun and workpiece surface (H), scan width (S w) and shift distance (S). The present work aims firstly, setting the pr oper welding conditions to get sound joint between commercially pure copper (C10 200) and AISI 316 stainless steel plates 8 mm thickness. Secondly, investigate t he effect of Electron Beam (EB) shift, single-sided and double-sided welds on the mechanical, metallurgical and chemical properties of the weld bead. Due to t he high difference in thermal conductivity between copper and stainless steel, E lectron Beam (EB) was shifted towards copper with different values. These values were ranged from 0.3 to 0.9 mm in welding without preheating of copper plate an d from 0.1 to 0.4 mm with preheating. Number of joints were welded using variabl e EBW parameters in view to obtain the sound weld bead. These parameters are as follows: gradual reduction I w=51 to 49 mA, I F=845 mA, V=8 mm/sec , H=130 mm, S w=500 μm and S=0.4 mm. The investigation has shown t hat, the copper (C10200) plate must be preheated to get sound welded joint with AISI 316 stainless steel using the EBW process. The tensile fracture in all wel ded samples occurred in copper plate away from the weld bead. This reflects that the weld bead tensile strength is greater than the copper strength. The EB shif t has slight effect on hardness distribution through weld bead. The hardness val ue (H v) reduces in gradual manner from stainless steel hardness to copper one. The EB shift distance has no significant effect on the impact toughness.展开更多
The steady, laminar, incompressible and two dimensional micropolar flow between two porous disks was investigated using optimal homotopy asymptotic method(OHAM) and fourth order Runge–Kutta numerical method. Comparis...The steady, laminar, incompressible and two dimensional micropolar flow between two porous disks was investigated using optimal homotopy asymptotic method(OHAM) and fourth order Runge–Kutta numerical method. Comparison between OHAM and numerical method shows that OHAM is an exact and high efficient method for solving these kinds of problems. The results are presented to study the velocity and rotation profiles for different physical parameters such as Reynolds number, vortex viscosity parameter, spin gradient viscosity and microinertia density parameter. As an important outcome, the magnitude of the microrotation increases with an increase in the values of injection velocity while it decreases by increasing the values of suction velocity.展开更多
The project"Groundwater Investigation in the Cuvelai-Etosha Basin"was a 3 year project in the framework of the German-Namibian Technical Cooperation,concluded between the Republic of Namibia and the Federal ...The project"Groundwater Investigation in the Cuvelai-Etosha Basin"was a 3 year project in the framework of the German-Namibian Technical Cooperation,concluded between the Republic of Namibia and the Federal Republic of Germany.The study is conducted by the Department of Water Affairs and Forestry(DWAF) and the Federal Institute for Geosciences and Natural Resources(BGR).展开更多
In recent years,great efforts have been made on the geoparks’ application and construction,but there is a shortage of research on the theories and methodologies of geoheritage investigation and assessment. Based on t...In recent years,great efforts have been made on the geoparks’ application and construction,but there is a shortage of research on the theories and methodologies of geoheritage investigation and assessment. Based on the summaries of having finished geoheritage investtigation and assessment and geopark construction projects,some key technologic methods analyzed in this paper are as follows:(1)展开更多
Lack of potable water supply source is among the crucial problems in developing countries,especially in Arid to Semi Arid regions,like Eritrea.In such cases groundwater is the best if not the only resource to be looke...Lack of potable water supply source is among the crucial problems in developing countries,especially in Arid to Semi Arid regions,like Eritrea.In such cases groundwater is the best if not the only resource to be looked for to alleviate the problem.A Norwegian Church Aid funded groundwater development project was implemented for ten villages dispersedly located in Southern Zone of Eritrea,which are with展开更多
A geo-environmental investigation is carried out to identify the suitability for treatment,storage and disposal facility(TSDF) in the industrial area at Perundurai,Tamilnadu(India).State industries promotion corporati...A geo-environmental investigation is carried out to identify the suitability for treatment,storage and disposal facility(TSDF) in the industrial area at Perundurai,Tamilnadu(India).State industries promotion corporation of Tamilnadu(SIPCOT), Perundurai is a fast growing industrial centre therefore,needs a common utility i.e.TSDF site for safe management of the industrial wastes.展开更多
With the gradual acceleration of urbanization speed and continuous improvements of agricultural productivity, the number of migrant workers is increasing. The living conditions of this group in cities determine the qu...With the gradual acceleration of urbanization speed and continuous improvements of agricultural productivity, the number of migrant workers is increasing. The living conditions of this group in cities determine the quality of urbanization in China, and are of great and far-reaching significance to Chinese construction of comprehensive well-off society. This study took the migrant workers in Heilongjiang Province as the research object, and took the representative new-generation migrant workers as the respondent to have a comprehensive analysis of the employment status. The study focused on these aspects, such as nature information, employment selection, employment quality, and social security, etc. Finally, it provided valuable ideas and methods on the reasonable solutions of the employment problems of the migrant workers to better increase farmers＇ income and improve their living qualities.展开更多
Developing production and operation in scales in the major grain producing areas is the direction of the paper. Seizing the opportunity of modem agriculture comprehensive reform in two plains （Songnen Plain and Sanji...Developing production and operation in scales in the major grain producing areas is the direction of the paper. Seizing the opportunity of modem agriculture comprehensive reform in two plains （Songnen Plain and Sanjiang Plain） of Heilongjiang Province and supporting to build a new type of production and management based on the big grain production householding, which plays demonstration and leading roles, have an important strategic position in improving agricultural comprehensive production capacity and ensuring national food security. In this paper, based on the survey data about the big grain production households production operations and analyses of the obstacles in expansion of production in Heilongjiang Province, specific suggestions in supporting the development of the big grain production household were put forward, such as, increasing agricultural production socialized level; perfecting the service system of land transferring; improving financial policies and farmer-friendly policy measures and perfecting the agriculture socialized service system.展开更多
Al 2O 3 particle-reinforced material (6061 alloy ), which is one of new composites and characterized by high strength and small spe cific gravity, good wear resistance and corrosion resistance, has been widel y used i...Al 2O 3 particle-reinforced material (6061 alloy ), which is one of new composites and characterized by high strength and small spe cific gravity, good wear resistance and corrosion resistance, has been widel y used in industry. But it is difficult to machine. Because of electric conducti vity, it can be shaped and processed by electro-machining means. However, this kind of material is mixed with the electrically conductive substances and the di electrically conductive substances, its machining process shows substantially di fferent from the machining of ordinary metal materials. This paper, based on a c ontrast experiment, investigates the machining mechanism and technique by WEDM t o shape the material and gives the optimum selection for the electric paramete rs in operation. The technologic index of shaping the new material by WEDM includes the cutting r ate and the surface roughness. There are a lot of factors that affect the techno logic index of WEDM, in which the electric parameters such as the machining volt age and current as well as the pulse duration, interval and frequency, play an i mportant part. In this experiment, the study focus mainly on the effect of the e lectric parameters on machining process and an orthogonal design is employed to select the proper electric parameters. By experiment, we find how the voltage and current affect machining process and study the removal mechanism by WEDM-HS to machine Al 2O 3 particle-reinforce d material. Besides the machining current and voltage, there are still other fac tors that can affect machining process and state. In order to find out which is the most important factor and to optimize the electric parameters, the orthogona l design has been adopted to perform the experiment. By the analysis to the rela tive differences among different factor levels, the rank of significance for fou r factors is in turn the pulse duration, the voltage, the machining current and the pulse interval. At last we can draw a conclusion that 6061 alloy can be shaped by WEDM-HS, and give the suitable electric parameters to obtain good surface roughness and high machining efficiency.展开更多
The plant germplasm resources of Zhalantun grassland in the eastern Inner Mongolia were investigated in 2015.The order of plant biomass production in all the types of grassland decreased compared to 1985 as the follow...The plant germplasm resources of Zhalantun grassland in the eastern Inner Mongolia were investigated in 2015.The order of plant biomass production in all the types of grassland decreased compared to 1985 as the followings:mountain meadow(76.72%)>temperate meadow steppe(66.53%)>lowland meadow(55.03%)>temperate typical steppe(26.37%).There were 243 plant species belonging to 166 genera and 47 families in Zhalantun grassland,including 163 forage species,78 medicinal species and 82 ornamental plant species attributable to 103 genera of 33 families,65 genera of 29 families and 63 genera of 29 families,respectively.In addition,38 species of edible plants,29 species of toxic and harmful plants and five rare protected plants were found in this area.展开更多
An investigation has been carried out to compare th e cutting performance and tool life evaluation of high speed steel broach samp les. The comparison has been done between conventional M2 and Anti-Segregation Process...An investigation has been carried out to compare th e cutting performance and tool life evaluation of high speed steel broach samp les. The comparison has been done between conventional M2 and Anti-Segregation Process (ASP) ASP53 and ASP30 high speed steel broach samples. The ASP53 was a development material. The cutting performance was evaluated by measuring the c utting forces and calculating the specific cutting energy, an indicator of cutti ng performance. As the roughness of the machined surface is an important criter ion in the evaluation of performance of a tool, the surface roughness of the workpiece was studied as a function of undeformed chip thickness. The workpiec e material was 150M36 alloy steel used in manufacture of automobile engines. Th e performance tests were conducted at two cutting speeds, which were 0 7 m/min and 10.5 m/min respectively. This allowed a better understanding of the effect of cutting speed on tool performance. The wear tests were performed at a cuttin g speed on 10.5 m/min. The cutting edges of ASP broach samples were finer compared to that of M2. Ther e was no practical difference in the cutting forces and the specific cutting ene rgy while cutting with MS, ASP30 and ASP53 broach samples. The ASP30 and ASP53 tools have a better surface roughness on the machined surface than that of M2 at both cutting speeds. The ASP30 gave 2.25 times the life and an improved surfac e finish compared to M2 steel. The ASP53 gave 1.3 times the life of M2 steel. These results should prove useful to the tool designer and manufacturing enginee r.展开更多
Most of the plant homeodomain-containing proteins play important roles in regulating cell differentiation and organ development,and Arabidopsis GLABRA2(GL2),a member of the class IV homeodomain-Leucine zipper(HD-ZIP) ...Most of the plant homeodomain-containing proteins play important roles in regulating cell differentiation and organ development,and Arabidopsis GLABRA2(GL2),a member of the class IV homeodomain-Leucine zipper(HD-ZIP) proteins,is a trichome and non-root hair cell regulator.We展开更多
A new type of saddle field ion gun has been developed in our laboratories, and it can emit ions and a large proportion of energetic neutrals.The ion gun has been used in the neutral and ion impact radiation （NIIR） s...A new type of saddle field ion gun has been developed in our laboratories, and it can emit ions and a large proportion of energetic neutrals.The ion gun has been used in the neutral and ion impact radiation （NIIR） spectrometer to decrease the effect of charge accumulation on the surfaces of specimens. Some metals, including aluminium, copper and nickel and their oxides had been analysed by NIIR. By comparing the intensities of the spectral lines of the above metals and their oxides the intensification effect due to oxidation had been found. The ratio of intensities between Al I（3962（?）） for Al<sub>2</sub>O<sub>3</sub> and Al I （3962（?）） for Al is 120, so the effect can be seen clearly from the above experimental results. The mechanism of the intensification effect has been discussed in the paper.展开更多
In this paper, damages and annealing effects of X,Y and Z cut LiNbO-3 implanted by 350keV high energy Ti (1.5 x 10<sup>17</sup> / cm<sup>2</sup>) are studied. The surface damages of X,Y cut pla...In this paper, damages and annealing effects of X,Y and Z cut LiNbO-3 implanted by 350keV high energy Ti (1.5 x 10<sup>17</sup> / cm<sup>2</sup>) are studied. The surface damages of X,Y cut plates are nearly amorphous, but the surface damage of Z cut does not reach saturation. Radiation damage is mainly due to Nb moving atoms and Ti atoms occupy the interstitial sites. By annealing the sample at 1000℃, most damage is removed from the boundary between implanted layer and LiNbO<sub>3</sub> base to surface.展开更多
Introduction Cancer is an attractive target of gene therapy and currently represents the disease in most clinical trials[1]. Strategies for cancer gene therapy include: (1) stimulation of immune responses to tumor cel...Introduction Cancer is an attractive target of gene therapy and currently represents the disease in most clinical trials[1]. Strategies for cancer gene therapy include: (1) stimulation of immune responses to tumor cells,(2) delivery of specific enzymes展开更多
As it is known a complete coverage of cotton(Gossypium hirsutum L.) genome with hypoaneuploids is not still realized.Therefore the detection of new types of aneuploids especially in different cytogenetic collections i...As it is known a complete coverage of cotton(Gossypium hirsutum L.) genome with hypoaneuploids is not still realized.Therefore the detection of new types of aneuploids especially in different cytogenetic collections is very useful.In Uzbekistan,long-term investigations towards development展开更多
Tibet Plateau is Known as "the Roof of the World" with the area of 1,220,000km^2, which is about 1/8 land area of China. Because of the high elevation, cold climate and it caused difficulties in regional eco...Tibet Plateau is Known as "the Roof of the World" with the area of 1,220,000km^2, which is about 1/8 land area of China. Because of the high elevation, cold climate and it caused difficulties in regional economic planning and land resources management. Since 1985, the land use investigation in Tibet has been carried out, in which the basic data and thematic maps must be obtained and completed at county and township levels, in order to meet the needs of local administrations. In the investigation, remote sensing technology was comprehensively adopted. At present, the investigation in county level had been completed and the compilation is going to be carried out. Due to paying a great attention to studying on a series of key technical problems, the systematic methods of using remote sensing technology in the plateau land use investigation were formed and successfully put into application.展开更多
基金Projects(5147420851304208)supported by the National Natural Science Foundation of China+3 种基金Project supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)ChinaProject(SKLCRSM12X01)supported by the State Key Laboratory of Coal Resources and Mine SafetyChina University of Mining and Technology
文摘Numerical investigation was performed to examine the effect of rear barrier pillar on stress distribution around a longwall face. Salamon theoretical formula was used to calculate the parameters of the caving zone, which was later assigned to double yield constitutive model in FLAC3 D. Numerical results demonstrate that high stress concentration zone exists above the region where the second open-off cut intersects with the rear barrier pillar due to stress transfer and plastic zone expansion. It is also found that the maximum vertical stresses with varied distance to the seam floor are all within the projective plane of the rear barrier pillar and their positions concentrate on the barrier pillar adjacent to the connection corner of the second open-off cut. In addition, position of the maximum vertical stresses abruptly transfer from the connection corner adjacent to former panel to that adjacent to current panel along the panel direction.
基金supported by the Natural Science Foundation of Heilongjiang Province,China(LH2019A008)the National Natural Science Foundation of China(51508123,named‘Study on blast response of floating roof storage tank in material point method’).
文摘The dynamic response of a multi-cabin protective structure subjected to impact load directly affects the protective performance of materials;thus,studying the dynamic response and communication law of wave effect of the load plays an important role in the prediction of protective performance.In this study,the protection experiments of box-structure under air-and/or water-medium are conducted,the dynamic response of the structure subjected to low-impact load is analyzed,and the corresponding numerical simulations are analyzed using the theory of finite element method(FEM).Combined with experimental and FEM simulations,the shock strain distribution,acceleration attenuation,and signal energy in defensive materials are determined.Based on the results,the metal structure exhibits good absorption characteristics for shock vibration.Using the experimental data,we also show that the attenuation of shock wave in water medium should be significantly better than that in air medium,and the protective structure should be designed for a combination of water and air mediums.Meanwhile,the numerical simulation can provide a quantitative analysis process for dynamic analysis of defensive materials.
基金Project(51176045)supported by the National Natural Science Foundation of ChinaProject(201208430262)supported by the National Studying Abroad Foundation of China
文摘In order to reveal combustion characteristics of H_2/air mixture in a micro-combustor with and without bluff body, the effects of inlet velocities, equivalence ratios and bluff body's blockage ratios on the temperature field, pressure of the combustor wall, combustion efficiency and blow-off limit were investigated. The numerical results indicate that the sudden expansion plate micro combustor with bluff body could enhance the turbulent disturbance of the mixed gas in the combustion chamber and the combustion condition is improved. Moreover, a low-speed and high temperature recirculation region was formed between the sudden expansion step and the bluff body so that the high and uniform wall temperature(>1000 K) could be gotten. As a result, it could strengthen the mixing process, prolong the residence time of gas, control the flame position effectively and widen the operation range by the synergistic effect of the bluff body and steps. When the blockage ratio ranged from 0.3 to 0.6, it could be found that the bluff body could play a stabilizing effect and expand combustion blow burning limit, and combustion efficiency firstly was increased with the inlet velocity and equivalence ratio, and then was decreased.
文摘Joints of copper and stainless steels are used in a er ospace applications. Production of these joints by fusion welding faces many dif ficulties. This may be due to the differences in their physical, metallurgical a nd mechanical properties. Electron Beam Welding (EBW) process has been found to be especially well suited in this area. Selection of the appropriate welding par ameters needs thorough investigations. These parameters include: preheat tempera ture (℃), welding current (I w), focusing current (I F), welding spee d (V), height between the gun and workpiece surface (H), scan width (S w) and shift distance (S). The present work aims firstly, setting the pr oper welding conditions to get sound joint between commercially pure copper (C10 200) and AISI 316 stainless steel plates 8 mm thickness. Secondly, investigate t he effect of Electron Beam (EB) shift, single-sided and double-sided welds on the mechanical, metallurgical and chemical properties of the weld bead. Due to t he high difference in thermal conductivity between copper and stainless steel, E lectron Beam (EB) was shifted towards copper with different values. These values were ranged from 0.3 to 0.9 mm in welding without preheating of copper plate an d from 0.1 to 0.4 mm with preheating. Number of joints were welded using variabl e EBW parameters in view to obtain the sound weld bead. These parameters are as follows: gradual reduction I w=51 to 49 mA, I F=845 mA, V=8 mm/sec , H=130 mm, S w=500 μm and S=0.4 mm. The investigation has shown t hat, the copper (C10200) plate must be preheated to get sound welded joint with AISI 316 stainless steel using the EBW process. The tensile fracture in all wel ded samples occurred in copper plate away from the weld bead. This reflects that the weld bead tensile strength is greater than the copper strength. The EB shif t has slight effect on hardness distribution through weld bead. The hardness val ue (H v) reduces in gradual manner from stainless steel hardness to copper one. The EB shift distance has no significant effect on the impact toughness.
文摘The steady, laminar, incompressible and two dimensional micropolar flow between two porous disks was investigated using optimal homotopy asymptotic method(OHAM) and fourth order Runge–Kutta numerical method. Comparison between OHAM and numerical method shows that OHAM is an exact and high efficient method for solving these kinds of problems. The results are presented to study the velocity and rotation profiles for different physical parameters such as Reynolds number, vortex viscosity parameter, spin gradient viscosity and microinertia density parameter. As an important outcome, the magnitude of the microrotation increases with an increase in the values of injection velocity while it decreases by increasing the values of suction velocity.
文摘The project"Groundwater Investigation in the Cuvelai-Etosha Basin"was a 3 year project in the framework of the German-Namibian Technical Cooperation,concluded between the Republic of Namibia and the Federal Republic of Germany.The study is conducted by the Department of Water Affairs and Forestry(DWAF) and the Federal Institute for Geosciences and Natural Resources(BGR).
文摘In recent years,great efforts have been made on the geoparks’ application and construction,but there is a shortage of research on the theories and methodologies of geoheritage investigation and assessment. Based on the summaries of having finished geoheritage investtigation and assessment and geopark construction projects,some key technologic methods analyzed in this paper are as follows:(1)
文摘Lack of potable water supply source is among the crucial problems in developing countries,especially in Arid to Semi Arid regions,like Eritrea.In such cases groundwater is the best if not the only resource to be looked for to alleviate the problem.A Norwegian Church Aid funded groundwater development project was implemented for ten villages dispersedly located in Southern Zone of Eritrea,which are with
文摘A geo-environmental investigation is carried out to identify the suitability for treatment,storage and disposal facility(TSDF) in the industrial area at Perundurai,Tamilnadu(India).State industries promotion corporation of Tamilnadu(SIPCOT), Perundurai is a fast growing industrial centre therefore,needs a common utility i.e.TSDF site for safe management of the industrial wastes.
基金Supported by the Social Science Research in Heilongjiang(13B007)the Post-doctoral Scientific Research in Heilongjiang Province(LBH-Q14028)
文摘With the gradual acceleration of urbanization speed and continuous improvements of agricultural productivity, the number of migrant workers is increasing. The living conditions of this group in cities determine the quality of urbanization in China, and are of great and far-reaching significance to Chinese construction of comprehensive well-off society. This study took the migrant workers in Heilongjiang Province as the research object, and took the representative new-generation migrant workers as the respondent to have a comprehensive analysis of the employment status. The study focused on these aspects, such as nature information, employment selection, employment quality, and social security, etc. Finally, it provided valuable ideas and methods on the reasonable solutions of the employment problems of the migrant workers to better increase farmers＇ income and improve their living qualities.
基金Supported by the Stage Achievement of Social Science Fund Project of Heilongjiang Province and the Application of Technology Research(12C053)the Development Project in Heilongjiang Province(2013R0242)
文摘Developing production and operation in scales in the major grain producing areas is the direction of the paper. Seizing the opportunity of modem agriculture comprehensive reform in two plains （Songnen Plain and Sanjiang Plain） of Heilongjiang Province and supporting to build a new type of production and management based on the big grain production householding, which plays demonstration and leading roles, have an important strategic position in improving agricultural comprehensive production capacity and ensuring national food security. In this paper, based on the survey data about the big grain production households production operations and analyses of the obstacles in expansion of production in Heilongjiang Province, specific suggestions in supporting the development of the big grain production household were put forward, such as, increasing agricultural production socialized level; perfecting the service system of land transferring; improving financial policies and farmer-friendly policy measures and perfecting the agriculture socialized service system.
文摘Al 2O 3 particle-reinforced material (6061 alloy ), which is one of new composites and characterized by high strength and small spe cific gravity, good wear resistance and corrosion resistance, has been widel y used in industry. But it is difficult to machine. Because of electric conducti vity, it can be shaped and processed by electro-machining means. However, this kind of material is mixed with the electrically conductive substances and the di electrically conductive substances, its machining process shows substantially di fferent from the machining of ordinary metal materials. This paper, based on a c ontrast experiment, investigates the machining mechanism and technique by WEDM t o shape the material and gives the optimum selection for the electric paramete rs in operation. The technologic index of shaping the new material by WEDM includes the cutting r ate and the surface roughness. There are a lot of factors that affect the techno logic index of WEDM, in which the electric parameters such as the machining volt age and current as well as the pulse duration, interval and frequency, play an i mportant part. In this experiment, the study focus mainly on the effect of the e lectric parameters on machining process and an orthogonal design is employed to select the proper electric parameters. By experiment, we find how the voltage and current affect machining process and study the removal mechanism by WEDM-HS to machine Al 2O 3 particle-reinforce d material. Besides the machining current and voltage, there are still other fac tors that can affect machining process and state. In order to find out which is the most important factor and to optimize the electric parameters, the orthogona l design has been adopted to perform the experiment. By the analysis to the rela tive differences among different factor levels, the rank of significance for fou r factors is in turn the pulse duration, the voltage, the machining current and the pulse interval. At last we can draw a conclusion that 6061 alloy can be shaped by WEDM-HS, and give the suitable electric parameters to obtain good surface roughness and high machining efficiency.
基金Forestry Science and Technology Extension Demonstration Project of Central Finance(TG 02)。
文摘The plant germplasm resources of Zhalantun grassland in the eastern Inner Mongolia were investigated in 2015.The order of plant biomass production in all the types of grassland decreased compared to 1985 as the followings:mountain meadow(76.72%)>temperate meadow steppe(66.53%)>lowland meadow(55.03%)>temperate typical steppe(26.37%).There were 243 plant species belonging to 166 genera and 47 families in Zhalantun grassland,including 163 forage species,78 medicinal species and 82 ornamental plant species attributable to 103 genera of 33 families,65 genera of 29 families and 63 genera of 29 families,respectively.In addition,38 species of edible plants,29 species of toxic and harmful plants and five rare protected plants were found in this area.
文摘An investigation has been carried out to compare th e cutting performance and tool life evaluation of high speed steel broach samp les. The comparison has been done between conventional M2 and Anti-Segregation Process (ASP) ASP53 and ASP30 high speed steel broach samples. The ASP53 was a development material. The cutting performance was evaluated by measuring the c utting forces and calculating the specific cutting energy, an indicator of cutti ng performance. As the roughness of the machined surface is an important criter ion in the evaluation of performance of a tool, the surface roughness of the workpiece was studied as a function of undeformed chip thickness. The workpiec e material was 150M36 alloy steel used in manufacture of automobile engines. Th e performance tests were conducted at two cutting speeds, which were 0 7 m/min and 10.5 m/min respectively. This allowed a better understanding of the effect of cutting speed on tool performance. The wear tests were performed at a cuttin g speed on 10.5 m/min. The cutting edges of ASP broach samples were finer compared to that of M2. Ther e was no practical difference in the cutting forces and the specific cutting ene rgy while cutting with MS, ASP30 and ASP53 broach samples. The ASP30 and ASP53 tools have a better surface roughness on the machined surface than that of M2 at both cutting speeds. The ASP30 gave 2.25 times the life and an improved surfac e finish compared to M2 steel. The ASP53 gave 1.3 times the life of M2 steel. These results should prove useful to the tool designer and manufacturing enginee r.
文摘Most of the plant homeodomain-containing proteins play important roles in regulating cell differentiation and organ development,and Arabidopsis GLABRA2(GL2),a member of the class IV homeodomain-Leucine zipper(HD-ZIP) proteins,is a trichome and non-root hair cell regulator.We
文摘A new type of saddle field ion gun has been developed in our laboratories, and it can emit ions and a large proportion of energetic neutrals.The ion gun has been used in the neutral and ion impact radiation （NIIR） spectrometer to decrease the effect of charge accumulation on the surfaces of specimens. Some metals, including aluminium, copper and nickel and their oxides had been analysed by NIIR. By comparing the intensities of the spectral lines of the above metals and their oxides the intensification effect due to oxidation had been found. The ratio of intensities between Al I（3962（?）） for Al<sub>2</sub>O<sub>3</sub> and Al I （3962（?）） for Al is 120, so the effect can be seen clearly from the above experimental results. The mechanism of the intensification effect has been discussed in the paper.
文摘In this paper, damages and annealing effects of X,Y and Z cut LiNbO-3 implanted by 350keV high energy Ti (1.5 x 10<sup>17</sup> / cm<sup>2</sup>) are studied. The surface damages of X,Y cut plates are nearly amorphous, but the surface damage of Z cut does not reach saturation. Radiation damage is mainly due to Nb moving atoms and Ti atoms occupy the interstitial sites. By annealing the sample at 1000℃, most damage is removed from the boundary between implanted layer and LiNbO<sub>3</sub> base to surface.
基金supported by a predoctoral fellowship from the National Institutes of Health and a research grant from the National Science Foundation
文摘Introduction Cancer is an attractive target of gene therapy and currently represents the disease in most clinical trials[1]. Strategies for cancer gene therapy include: (1) stimulation of immune responses to tumor cells,(2) delivery of specific enzymes
文摘As it is known a complete coverage of cotton(Gossypium hirsutum L.) genome with hypoaneuploids is not still realized.Therefore the detection of new types of aneuploids especially in different cytogenetic collections is very useful.In Uzbekistan,long-term investigations towards development
文摘Tibet Plateau is Known as "the Roof of the World" with the area of 1,220,000km^2, which is about 1/8 land area of China. Because of the high elevation, cold climate and it caused difficulties in regional economic planning and land resources management. Since 1985, the land use investigation in Tibet has been carried out, in which the basic data and thematic maps must be obtained and completed at county and township levels, in order to meet the needs of local administrations. In the investigation, remote sensing technology was comprehensively adopted. At present, the investigation in county level had been completed and the compilation is going to be carried out. Due to paying a great attention to studying on a series of key technical problems, the systematic methods of using remote sensing technology in the plateau land use investigation were formed and successfully put into application.
