Electrocatalytic reduction of carbon dioxide(CO_(2))to carbon monoxide(CO)is an effective strategy to achieve carbon neutrality.High selective and low-cost catalysts for the electrocatalytic reduction of CO_(2)have re...Electrocatalytic reduction of carbon dioxide(CO_(2))to carbon monoxide(CO)is an effective strategy to achieve carbon neutrality.High selective and low-cost catalysts for the electrocatalytic reduction of CO_(2)have received increasing attention.In contrast to the conventional tube furnace method,the high-temperature shock(HTS)method enables ultra-fast thermal processing,superior atomic efficiency,and a streamlined synthesis protocol,offering a simplified method for the preparation of high-performance single-atom catalysts(SACs).The reports have shown that nickel-based SACs can be synthesized quickly and conveniently using the HTS method,making their application in CO_(2)reduction reactions(CO_(2)RR)a viable and promising avenue for further exploration.In this study,the effect of heating temperature,metal loading and different nitrogen(N)sources on the catalyst morphology,coordination environment and electrocatalytic performance were investigated.Under optimal conditions,0.05Ni-DCD-C-1050 showed excellent performance in reducing CO_(2)to CO,with CO selectivity close to 100%(−0.7 to−1.0 V vs RHE)and current density as high as 130 mA/cm^(2)(−1.1 V vs RHE)in a flow cell under alkaline environment.展开更多
This paper focuses on the high-temperature tensile failure mechanism of RTM(resin transfer moulding)-made symmetric and asymmetric composite T-joints.The failure modes as well as the load-displacement curves of symmet...This paper focuses on the high-temperature tensile failure mechanism of RTM(resin transfer moulding)-made symmetric and asymmetric composite T-joints.The failure modes as well as the load-displacement curves of symmetric(three specimens)and asymmetric(three specimens)composite T-joints were determined by tensile tests at room and high temperatures.Progressive damage models(PDMs)of symmetric and asymmetric composite T-joints at room and high temperatures were established based on mixed criteria,and the result predicted from the aforementioned PDMs were compared with experimental data.The predicted initial and final failure loads and failure modes are in good agreement with the experimental results.The failure mechanisms of composite T-joints at different temperatures were investigated by scanning electron microscopy.The results reveal that while the failure mode of asymmetric T-joints at high temperatures resembles that at room temperature,there is a difference in the failure modes of symmetric T-joints.The ultimate failure load of symmetric and asymmetric T-joints at elevated temperatures increases and reduces by 18.4%and 4.97%,albeit with a more discrete distri-bution.This work is expected to provide us with more knowledge about the usability of composite T-joints in elevated temperature environments.展开更多
Dynamic compression experiments were conducted on red sandstone utilizing a split Hopkinson pressure bar(SHPB)to study the loading rate and high temperatures on their mechanically deformed properties and ultimate fail...Dynamic compression experiments were conducted on red sandstone utilizing a split Hopkinson pressure bar(SHPB)to study the loading rate and high temperatures on their mechanically deformed properties and ultimate failure modes,and to analyze the correlation between the strain rate,temperature,peak strength,and ultimate failure modes.The results show that the mass decreases with the increase of treatment temperature,and the pattern of the stress−strain curves is not impacted by the increase of impact velocity.Under a fixed temperature,the higher the impact velocity,the higher the strain rate and dynamical compression strength,indicating a strain rate hardening effect for red sandstone.With an increasing treatment temperature,the strain rate gradually increases when the impact loading remains unchanged,suggesting a rise in the deformability of red sandstone under high-temperature environment.Raise in both impact velocity and treatment temperature leads to an intensification of the damage features of the red sandstone.Similarly,higher strain rates lead to the intensification of the final damage mode of red sandstone regardless of the change in treatment temperature.Moreover,a dynamic damage constitutive model that considers the impacts of strain rate and temperature is proposed based on experimental results.展开更多
Negative Poisson ratio(NPR)steel is a new material with high strength and toughness.This study conducted tensile tests at elevated temperatures to investigate the mechanical properties of NPR steel at high temperature...Negative Poisson ratio(NPR)steel is a new material with high strength and toughness.This study conducted tensile tests at elevated temperatures to investigate the mechanical properties of NPR steel at high temperatures.The stress−strain curve,ultimate strength,yield strength,modulus of elasticity,elongation after fracture,and percentage reduction of area of NPR steel bars were measured at 9 different temperatures ranging from 20 to 800℃.The experimental results indicate that high-temperature environments significantly affect the mechanical properties of NPR steel.However,compared to other types of steel,NPR steel exhibits better resistance to deformation.When the test temperature is below 700℃,NPR steel exhibits a ductile fracture characteristic,while at 800℃,it exhibits a brittle fracture characteristic.Finally,based on the experimental findings,a constitutive model suitable for NPR steel at high temperatures is proposed.展开更多
The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental ...The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.展开更多
The effects of preheating temperature and W powder size on the Self propagating High temperature Synthesis(SHS) of Ti W C system were studied. Preheated mixtures and the decrease of W powder size can accelerate the fo...The effects of preheating temperature and W powder size on the Self propagating High temperature Synthesis(SHS) of Ti W C system were studied. Preheated mixtures and the decrease of W powder size can accelerate the formation of (W,Ti)C powders. The uniphase (W,Ti)C (WC∶TiC=5∶5) powders with 0.32% free carbon were synthesized from Ti, W, C powders by SHS. The powder size of the product was 3～5 μm.展开更多
Based on reanalyzing test results of uniaxial compressive behavior of concrete at constant high temperatures in China, with the compressive cube strength of concrete from 20 to 80 MPa, unified formulas for uniaxial co...Based on reanalyzing test results of uniaxial compressive behavior of concrete at constant high temperatures in China, with the compressive cube strength of concrete from 20 to 80 MPa, unified formulas for uniaxial compressive strength, elastic modulus, strain at peak uniaxial compression and mathematical expression for unaxial compressive stress-strain relations for the concrete at constant high temperatures were studied. Furthermore, the axial stress-axial strain relations between laterally confined concrete under axial compression and multiaxial stress-strain relations for steel at constant high temperatures were studied. Finally, based on continuum mechanics, the mechanics model for concentric cylinders of circular steel tube with concrete core of entire section loaded at constant high temperatures was established. Applying elasto-plastic analysis method, a FORTRAN program was developed, and the concrete-filled circular steel tubular （CFST） stub colunms at constant high temperatures were analyzed. The analysis results are in agreement with the experiment ones from references.展开更多
The tribological behaviors of the nano-diamond particles including the nano- diamond and the nano-diamond modified were studied at high temperature using SRV multifunctional test system. The worn steel surfaces were a...The tribological behaviors of the nano-diamond particles including the nano- diamond and the nano-diamond modified were studied at high temperature using SRV multifunctional test system. The worn steel surfaces were analyzed by means of X-ray photoelectron spectroscopy (XPS). The results show that nano-diamond particles can obviously improve the antiwear and friction reducing properties of the base oil at high temperature and the high load. The friction coefficient of the nano-diamond is very low at 200 ℃ when the test load is not more than 20 N. This tribological behaviors should attributed to the similarly to “ball bearing” lubrication action of the nano-diamond particles, so the movement between tribological pairs become sliding/rolling. The nano-diamond modified by dimer ester possesses excellent antiwear and friction reducing performance at 500 ℃ and load 500 N. The tribochemical reaction film between the nano-diamond particles and the renascent wear surface plays dominating lubrication role and the presence of the dimer ester on the rubbing surface can be propitious to form lubrication film containing nano- diamond on the worn surface at high temperature and high load.展开更多
Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high t...Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high temperature by changing compositions and temperatures were investigated by means of optical microscope and scanning electron microscope. Among the three compositions of cladding layer, i.e. Ni21+20%WC+0.5%CeO2, Ni25+20%WC+0.5%CeO2 and Ni60+20%WC+0.5%CeO2, the experimental results show that Ni21+20%WC+ 0.5%CeO2 cladding layer is made up of finer grains, and presents the best abrasion wear behavior at high temperature. The wear pattern of laser cladding layer is mainly grain abrasion at lower temperature, and it would be changed to adhesive abrasion and oxide abrasion at higher temperature.展开更多
This study numerically simulated and investigated the flow field characteristics of a typical dual-pulse solid rocket motor with a soft pulse separation device through thermal insulation ablation under high-temperatur...This study numerically simulated and investigated the flow field characteristics of a typical dual-pulse solid rocket motor with a soft pulse separation device through thermal insulation ablation under high-temperature dual-pulse erosion.The ablation rate of ethylene-propylene-diene monomer(EPDM)insulator was measured after the experiment.Experimental results were analyzed through scanning electron microscopy and microcomputed tomography.The ablation mechanism of the EPDM insulator under the operation conditions of a dual-pulse solid rocket motor was evaluated by analyzing the results.The results reveal that the internal flow field of the motor with a soft pulse separation device is uniform.The original charred layer existing on the EPDM insulator surface in the first pulse combustor is the decisive factor affecting the final ablation rate of the dual-pulse motor during the second pulse operation,and the ablation characteristic region is easily formed with the exfoliation of the charred layer.The ablation rate difference of the insulator increases with gas velocity.展开更多
Piezoelectric ceramic based high-temperature acoustic emission(AE)sensor is required urgently in the structural health monitoring of high-temperature fields.In this research,a series of 0.45(BiSc_(x)O_(3)-BiFe_(1-x)O_...Piezoelectric ceramic based high-temperature acoustic emission(AE)sensor is required urgently in the structural health monitoring of high-temperature fields.In this research,a series of 0.45(BiSc_(x)O_(3)-BiFe_(1-x)O_(3))-0.48PbTiO_(3)-0.07BaTiO_(3)(BSc_(x)Fe_(1-x)-PT-BT,n(Sc)/n(Fe)=0.4/0.6-0.6/0.4)ceramics with both high Curie temperature and large piezoelectric constant were presented.The structure and electrical properties of BSc_(x)Fe_(1-x)-PT-BT ceramics as a function of n(Sc)/n(Fe)have been systematically investigated.All the ceramics possess a perovskite structure,and the phase approaches from the rhombohedral toward the tetragonal phase with the decrease of n(Sc)/n(Fe).The BSc_(0.5)Fe_(0.5)-PT-BT and BSc_(0.5)Fe_(0.5)-PT-BT piezoelectric ceramics exhibit good piezoelectricity(d_(33)=250-281 pC/N),high Curie temperature(T_(C)=430-450℃)and excellent temperature stability.These improvements are greatly attributed to the balance between rhombohedral and tetragonal phase near morphotropic phase boundary with dense microstructure of ceramics.AE sensor based BSc_(0.5)Fe_(0.5)-PT-BT piezoelectric ceramic was designed,prepared and tested.The high-temperature stability of AE sensor was characterized through pencil-lead breaking with in situ high-temperature test.The noise of AE sensor is less than 40 dB,and the acoustic signal is up to 90 dB at 200℃.As a result,AE sensors based on BSc_(x)Fe_(1-x)-PT-BT piezoelectric ceramics are expected to be applied into the structural health monitoring of high temperature fields.展开更多
A soft-measuring approach is presented to measure the flux of liquid zinc with high temperature andcausticity. By constructing mathematical model based on neural networks, weighing the mass of liquid zinc, the fluxof ...A soft-measuring approach is presented to measure the flux of liquid zinc with high temperature andcausticity. By constructing mathematical model based on neural networks, weighing the mass of liquid zinc, the fluxof liquid zinc is acquired indirectly, the measuring on line and flux control are realized. Simulation results and indus-trial practice demonstrate that the relative error between the estimated flux value and practical measured flux value islower than 1.5%, meeting the need of industrial process.展开更多
Many kinds of high temperature superconductor （HTS） power machines such as HTS cable, HTS fault current limitcr and HTS magnet are cooled by liquid nitrogen. The level of liquid nitrogen should be monitored and cont...Many kinds of high temperature superconductor （HTS） power machines such as HTS cable, HTS fault current limitcr and HTS magnet are cooled by liquid nitrogen. The level of liquid nitrogen should be monitored and controlled to ensure the thermal stability and the dielectric strength as well. To measure the level, capacitance method and differential pressure method are usually used. However, each method has installation difficulties and measurement errors for unsteady state operation with varying system pressure. A new liquid level meter using a 2G HTS conductor is described, which has similar structure with the liquid helium level meter with NbTi filament. The level meter is fabricated with a parallel connected heater, which helps the separation of the superconducting region and normal region, considering the critical temperature, large heat capacity of conductor and cooling characteristics. The level of liquid nitrogen can be obtained from the measured voltage signal along the 2G HTS conductor. Design, fabrication and test results of the new liquid nitrogen level meter are presented.展开更多
As a new spraying technology used in the remanufacturing engineering, electro-thermal explosion spraying holds a lot of advantages. Electro-thermal explosion spraying coating aliquation phenomena are reduced and non-c...As a new spraying technology used in the remanufacturing engineering, electro-thermal explosion spraying holds a lot of advantages. Electro-thermal explosion spraying coating aliquation phenomena are reduced and non-crystal, micro-crystal and millimicron-crystal and other microstructure are formed. The corrosion-resistance ability of electro-thermal explosion spraying coating in high temperature environment was surveyed respectively. SEM equipped with EDS was employed to analyze the microstructure of spraying coating before and after corrosion. The corrosion-resistance mechanism of the spraying coating was discussed.展开更多
The effect of a high magnetic field up to 30T on phase transformation temperature and microstructure of Fe-based alloys has been reviewed. A high magnetic field accelerates ferrite transformation, changes the morpho...The effect of a high magnetic field up to 30T on phase transformation temperature and microstructure of Fe-based alloys has been reviewed. A high magnetic field accelerates ferrite transformation, changes the morphology of the transformed microstructures and increases the A3 and A1 temperature. In a magnetic field of 30T, the A1 temperature increases by about 37.1℃ for Fe-0.8C, the A3 temperature for pure Fe increases by about 33.1℃. The measured transformation temperature data are not consistent with calculation results using Weiss molecular field theory. Ferrite grains are elongated and aligned along the direction of magnetic field in Fe-0.4C and Fe-0.6C alloys by ferrite transformation, but elongated and aligned structure was not found in pure Fe, Fe-0.05C alloy and Fe-1.5Mn-0.11C-0.1V alloy.展开更多
Carbon spheres with size of 50-300 nm were synthesized via a solvent-thermal reaction with calcium carbide and chloroform as reactants in a sealed autoclave.The morphologies and microstructures of carbon spheres befor...Carbon spheres with size of 50-300 nm were synthesized via a solvent-thermal reaction with calcium carbide and chloroform as reactants in a sealed autoclave.The morphologies and microstructures of carbon spheres before and after high temperature treatment(HTT) were characterized by X-ray diffractometry(XRD) ,scanning electronic microscopy(SEM) ,energy diffraction spectroscopy(EDS) ,and transmission electron microscopy(TEM) .The formation mechanism of carbon spheres was discussed.The results indicate that the carbon spheres convert to hollow polyhedron through HTT.Carbon spheres are composed of entangled and curve graphitic layers with short range order similar to cotton structure,and carbon polyhedron with dimension of 50-250 nm and shell thickness of 15-30 nm.The change of solid spheres to hollow polyhedron with branches gives a new evidence for formation mechanism of hollow carbon spheres.展开更多
High temperature corrosion of chromia forming Fe-base alloys by CO_(2) produces not only oxidation but also carburisation.The corrosion kinetics in CO_(2)-rich gas is found to be increased compared with that in air or...High temperature corrosion of chromia forming Fe-base alloys by CO_(2) produces not only oxidation but also carburisation.The corrosion kinetics in CO_(2)-rich gas is found to be increased compared with that in air or oxygen.As a result,higher alloy chromium levels are required to achieve protective chromia formation in CO_(2).Corrosion reaction mechanisms in CO_(2) are examined and the internal carburisation of alloys in low carbon activity CO_(2) gases are analysed based on the variation of pO_(2) at the interface of oxide and metal.Carbon penetration through chromia oxide scale has been revealed by atom probe tomography.The strategies to resist CO_(2) corrosion are reviewed by alloying of Si and/or Mn,forming additional diffusion barrier layers,and by adding sulphur to modify oxide grain boundaries to reduce carbon diffusion along the grain boundaries.展开更多
The oxidation of the ternary alloy Ni-15Cu-5Al in 1 × 105 Pa pure oxygen at 700 ℃ and 800 ℃ was studied. The results show that the behavior of the Ni-rich alloy is similar to that of the binary Ni-Al alloy with...The oxidation of the ternary alloy Ni-15Cu-5Al in 1 × 105 Pa pure oxygen at 700 ℃ and 800 ℃ was studied. The results show that the behavior of the Ni-rich alloy is similar to that of the binary Ni-Al alloy with the same Al content in the form of an external NiO layer coupled to the internal oxidation of aluminium. The presence of 15%(mole fraction) Cu cannot modify substantially the values of relevant parameters affecting the transition from the internal to the external oxidation of aluminium. The presence of 5 % Al reduces the oxidation rate of the corresponding Ni-Cu alloy during the whole oxidation stages, though 5 % Al is still insufficient to form protective external alumina scales.展开更多
基金supported by the National Key R&D Program of China(2024YFB4106400)National Natural Science Foundation of China(22209200,52302331)。
文摘Electrocatalytic reduction of carbon dioxide(CO_(2))to carbon monoxide(CO)is an effective strategy to achieve carbon neutrality.High selective and low-cost catalysts for the electrocatalytic reduction of CO_(2)have received increasing attention.In contrast to the conventional tube furnace method,the high-temperature shock(HTS)method enables ultra-fast thermal processing,superior atomic efficiency,and a streamlined synthesis protocol,offering a simplified method for the preparation of high-performance single-atom catalysts(SACs).The reports have shown that nickel-based SACs can be synthesized quickly and conveniently using the HTS method,making their application in CO_(2)reduction reactions(CO_(2)RR)a viable and promising avenue for further exploration.In this study,the effect of heating temperature,metal loading and different nitrogen(N)sources on the catalyst morphology,coordination environment and electrocatalytic performance were investigated.Under optimal conditions,0.05Ni-DCD-C-1050 showed excellent performance in reducing CO_(2)to CO,with CO selectivity close to 100%(−0.7 to−1.0 V vs RHE)and current density as high as 130 mA/cm^(2)(−1.1 V vs RHE)in a flow cell under alkaline environment.
基金supported by the Natural Science Foundation of Shanghai(Grant No.24ZR1401700)Fundamental Research Funds for the Central Universities(Grant No.2232022D-28)the Young Elite Scientists Sponsorship Program by the China Association for Science and Technology(Grant No.2016QNRC001).
文摘This paper focuses on the high-temperature tensile failure mechanism of RTM(resin transfer moulding)-made symmetric and asymmetric composite T-joints.The failure modes as well as the load-displacement curves of symmetric(three specimens)and asymmetric(three specimens)composite T-joints were determined by tensile tests at room and high temperatures.Progressive damage models(PDMs)of symmetric and asymmetric composite T-joints at room and high temperatures were established based on mixed criteria,and the result predicted from the aforementioned PDMs were compared with experimental data.The predicted initial and final failure loads and failure modes are in good agreement with the experimental results.The failure mechanisms of composite T-joints at different temperatures were investigated by scanning electron microscopy.The results reveal that while the failure mode of asymmetric T-joints at high temperatures resembles that at room temperature,there is a difference in the failure modes of symmetric T-joints.The ultimate failure load of symmetric and asymmetric T-joints at elevated temperatures increases and reduces by 18.4%and 4.97%,albeit with a more discrete distri-bution.This work is expected to provide us with more knowledge about the usability of composite T-joints in elevated temperature environments.
基金Project(BZ2024023)supported by the Jiangsu Province International Collaboration Program-Key National Industrial Technology Research and Development Cooperation,China。
文摘Dynamic compression experiments were conducted on red sandstone utilizing a split Hopkinson pressure bar(SHPB)to study the loading rate and high temperatures on their mechanically deformed properties and ultimate failure modes,and to analyze the correlation between the strain rate,temperature,peak strength,and ultimate failure modes.The results show that the mass decreases with the increase of treatment temperature,and the pattern of the stress−strain curves is not impacted by the increase of impact velocity.Under a fixed temperature,the higher the impact velocity,the higher the strain rate and dynamical compression strength,indicating a strain rate hardening effect for red sandstone.With an increasing treatment temperature,the strain rate gradually increases when the impact loading remains unchanged,suggesting a rise in the deformability of red sandstone under high-temperature environment.Raise in both impact velocity and treatment temperature leads to an intensification of the damage features of the red sandstone.Similarly,higher strain rates lead to the intensification of the final damage mode of red sandstone regardless of the change in treatment temperature.Moreover,a dynamic damage constitutive model that considers the impacts of strain rate and temperature is proposed based on experimental results.
基金Projects(41702320,52104125)supported by the National Natural Science Foundation of ChinaProject(ZR2021MD005)+2 种基金supported by the Natural Science Foundation of Shandong Province,ChinaProject(TMduracon2022002)supported by the Engineering Research Center of Marine Environmental Concrete Technology,Ministry of Education,China。
文摘Negative Poisson ratio(NPR)steel is a new material with high strength and toughness.This study conducted tensile tests at elevated temperatures to investigate the mechanical properties of NPR steel at high temperatures.The stress−strain curve,ultimate strength,yield strength,modulus of elasticity,elongation after fracture,and percentage reduction of area of NPR steel bars were measured at 9 different temperatures ranging from 20 to 800℃.The experimental results indicate that high-temperature environments significantly affect the mechanical properties of NPR steel.However,compared to other types of steel,NPR steel exhibits better resistance to deformation.When the test temperature is below 700℃,NPR steel exhibits a ductile fracture characteristic,while at 800℃,it exhibits a brittle fracture characteristic.Finally,based on the experimental findings,a constitutive model suitable for NPR steel at high temperatures is proposed.
基金Project(50574061) supported by the National Natural Science Foundation of ChinaProject(IRT0411) supported by the Changjiang Scholars and Innovative Research Team,Ministry of Education
文摘The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.
文摘The effects of preheating temperature and W powder size on the Self propagating High temperature Synthesis(SHS) of Ti W C system were studied. Preheated mixtures and the decrease of W powder size can accelerate the formation of (W,Ti)C powders. The uniphase (W,Ti)C (WC∶TiC=5∶5) powders with 0.32% free carbon were synthesized from Ti, W, C powders by SHS. The powder size of the product was 3～5 μm.
基金Projects(50438020 50578162) supported by the National Natural Sceince Foundation of China
文摘Based on reanalyzing test results of uniaxial compressive behavior of concrete at constant high temperatures in China, with the compressive cube strength of concrete from 20 to 80 MPa, unified formulas for uniaxial compressive strength, elastic modulus, strain at peak uniaxial compression and mathematical expression for unaxial compressive stress-strain relations for the concrete at constant high temperatures were studied. Furthermore, the axial stress-axial strain relations between laterally confined concrete under axial compression and multiaxial stress-strain relations for steel at constant high temperatures were studied. Finally, based on continuum mechanics, the mechanics model for concentric cylinders of circular steel tube with concrete core of entire section loaded at constant high temperatures was established. Applying elasto-plastic analysis method, a FORTRAN program was developed, and the concrete-filled circular steel tubular （CFST） stub colunms at constant high temperatures were analyzed. The analysis results are in agreement with the experiment ones from references.
文摘The tribological behaviors of the nano-diamond particles including the nano- diamond and the nano-diamond modified were studied at high temperature using SRV multifunctional test system. The worn steel surfaces were analyzed by means of X-ray photoelectron spectroscopy (XPS). The results show that nano-diamond particles can obviously improve the antiwear and friction reducing properties of the base oil at high temperature and the high load. The friction coefficient of the nano-diamond is very low at 200 ℃ when the test load is not more than 20 N. This tribological behaviors should attributed to the similarly to “ball bearing” lubrication action of the nano-diamond particles, so the movement between tribological pairs become sliding/rolling. The nano-diamond modified by dimer ester possesses excellent antiwear and friction reducing performance at 500 ℃ and load 500 N. The tribochemical reaction film between the nano-diamond particles and the renascent wear surface plays dominating lubrication role and the presence of the dimer ester on the rubbing surface can be propitious to form lubrication film containing nano- diamond on the worn surface at high temperature and high load.
文摘Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high temperature by changing compositions and temperatures were investigated by means of optical microscope and scanning electron microscope. Among the three compositions of cladding layer, i.e. Ni21+20%WC+0.5%CeO2, Ni25+20%WC+0.5%CeO2 and Ni60+20%WC+0.5%CeO2, the experimental results show that Ni21+20%WC+ 0.5%CeO2 cladding layer is made up of finer grains, and presents the best abrasion wear behavior at high temperature. The wear pattern of laser cladding layer is mainly grain abrasion at lower temperature, and it would be changed to adhesive abrasion and oxide abrasion at higher temperature.
基金financially supported by the National Natural Science Foundation of China,under grant numbers 51876177,51276150,and 51576165。
文摘This study numerically simulated and investigated the flow field characteristics of a typical dual-pulse solid rocket motor with a soft pulse separation device through thermal insulation ablation under high-temperature dual-pulse erosion.The ablation rate of ethylene-propylene-diene monomer(EPDM)insulator was measured after the experiment.Experimental results were analyzed through scanning electron microscopy and microcomputed tomography.The ablation mechanism of the EPDM insulator under the operation conditions of a dual-pulse solid rocket motor was evaluated by analyzing the results.The results reveal that the internal flow field of the motor with a soft pulse separation device is uniform.The original charred layer existing on the EPDM insulator surface in the first pulse combustor is the decisive factor affecting the final ablation rate of the dual-pulse motor during the second pulse operation,and the ablation characteristic region is easily formed with the exfoliation of the charred layer.The ablation rate difference of the insulator increases with gas velocity.
基金Project(SDBX2020010) supported by Shandong Postdoctoral Innovative Talents Support Plan,ChinaProjects(U1806221,U2006218) supported by the National Natural Science Foundation of China+1 种基金Project(ZR2020KA003)supported by Shandong Provincial Natural Science Foundation,ChinaProjects(2019GXRC017,2020GXRC051)supported by the Project of “20 Items of University” of Jinan,China。
文摘Piezoelectric ceramic based high-temperature acoustic emission(AE)sensor is required urgently in the structural health monitoring of high-temperature fields.In this research,a series of 0.45(BiSc_(x)O_(3)-BiFe_(1-x)O_(3))-0.48PbTiO_(3)-0.07BaTiO_(3)(BSc_(x)Fe_(1-x)-PT-BT,n(Sc)/n(Fe)=0.4/0.6-0.6/0.4)ceramics with both high Curie temperature and large piezoelectric constant were presented.The structure and electrical properties of BSc_(x)Fe_(1-x)-PT-BT ceramics as a function of n(Sc)/n(Fe)have been systematically investigated.All the ceramics possess a perovskite structure,and the phase approaches from the rhombohedral toward the tetragonal phase with the decrease of n(Sc)/n(Fe).The BSc_(0.5)Fe_(0.5)-PT-BT and BSc_(0.5)Fe_(0.5)-PT-BT piezoelectric ceramics exhibit good piezoelectricity(d_(33)=250-281 pC/N),high Curie temperature(T_(C)=430-450℃)and excellent temperature stability.These improvements are greatly attributed to the balance between rhombohedral and tetragonal phase near morphotropic phase boundary with dense microstructure of ceramics.AE sensor based BSc_(0.5)Fe_(0.5)-PT-BT piezoelectric ceramic was designed,prepared and tested.The high-temperature stability of AE sensor was characterized through pencil-lead breaking with in situ high-temperature test.The noise of AE sensor is less than 40 dB,and the acoustic signal is up to 90 dB at 200℃.As a result,AE sensors based on BSc_(x)Fe_(1-x)-PT-BT piezoelectric ceramics are expected to be applied into the structural health monitoring of high temperature fields.
基金Project (201AA411040) supported by National Plan and Development Committee.
文摘A soft-measuring approach is presented to measure the flux of liquid zinc with high temperature andcausticity. By constructing mathematical model based on neural networks, weighing the mass of liquid zinc, the fluxof liquid zinc is acquired indirectly, the measuring on line and flux control are realized. Simulation results and indus-trial practice demonstrate that the relative error between the estimated flux value and practical measured flux value islower than 1.5%, meeting the need of industrial process.
基金Project supported by the Second Stage of Brain Korea 21 Projects
文摘Many kinds of high temperature superconductor （HTS） power machines such as HTS cable, HTS fault current limitcr and HTS magnet are cooled by liquid nitrogen. The level of liquid nitrogen should be monitored and controlled to ensure the thermal stability and the dielectric strength as well. To measure the level, capacitance method and differential pressure method are usually used. However, each method has installation difficulties and measurement errors for unsteady state operation with varying system pressure. A new liquid level meter using a 2G HTS conductor is described, which has similar structure with the liquid helium level meter with NbTi filament. The level meter is fabricated with a parallel connected heater, which helps the separation of the superconducting region and normal region, considering the critical temperature, large heat capacity of conductor and cooling characteristics. The level of liquid nitrogen can be obtained from the measured voltage signal along the 2G HTS conductor. Design, fabrication and test results of the new liquid nitrogen level meter are presented.
文摘As a new spraying technology used in the remanufacturing engineering, electro-thermal explosion spraying holds a lot of advantages. Electro-thermal explosion spraying coating aliquation phenomena are reduced and non-crystal, micro-crystal and millimicron-crystal and other microstructure are formed. The corrosion-resistance ability of electro-thermal explosion spraying coating in high temperature environment was surveyed respectively. SEM equipped with EDS was employed to analyze the microstructure of spraying coating before and after corrosion. The corrosion-resistance mechanism of the spraying coating was discussed.
文摘The effect of a high magnetic field up to 30T on phase transformation temperature and microstructure of Fe-based alloys has been reviewed. A high magnetic field accelerates ferrite transformation, changes the morphology of the transformed microstructures and increases the A3 and A1 temperature. In a magnetic field of 30T, the A1 temperature increases by about 37.1℃ for Fe-0.8C, the A3 temperature for pure Fe increases by about 33.1℃. The measured transformation temperature data are not consistent with calculation results using Weiss molecular field theory. Ferrite grains are elongated and aligned along the direction of magnetic field in Fe-0.4C and Fe-0.6C alloys by ferrite transformation, but elongated and aligned structure was not found in pure Fe, Fe-0.05C alloy and Fe-1.5Mn-0.11C-0.1V alloy.
基金Project(2006CB600901) supported by the National Basic Research Program of ChinaProject(0991015) supported by Guangxi Natural Science Foundation,ChinaProject(200808MS083) supported by Guangxi Education Department Foundation,China
文摘Carbon spheres with size of 50-300 nm were synthesized via a solvent-thermal reaction with calcium carbide and chloroform as reactants in a sealed autoclave.The morphologies and microstructures of carbon spheres before and after high temperature treatment(HTT) were characterized by X-ray diffractometry(XRD) ,scanning electronic microscopy(SEM) ,energy diffraction spectroscopy(EDS) ,and transmission electron microscopy(TEM) .The formation mechanism of carbon spheres was discussed.The results indicate that the carbon spheres convert to hollow polyhedron through HTT.Carbon spheres are composed of entangled and curve graphitic layers with short range order similar to cotton structure,and carbon polyhedron with dimension of 50-250 nm and shell thickness of 15-30 nm.The change of solid spheres to hollow polyhedron with branches gives a new evidence for formation mechanism of hollow carbon spheres.
文摘High temperature corrosion of chromia forming Fe-base alloys by CO_(2) produces not only oxidation but also carburisation.The corrosion kinetics in CO_(2)-rich gas is found to be increased compared with that in air or oxygen.As a result,higher alloy chromium levels are required to achieve protective chromia formation in CO_(2).Corrosion reaction mechanisms in CO_(2) are examined and the internal carburisation of alloys in low carbon activity CO_(2) gases are analysed based on the variation of pO_(2) at the interface of oxide and metal.Carbon penetration through chromia oxide scale has been revealed by atom probe tomography.The strategies to resist CO_(2) corrosion are reviewed by alloying of Si and/or Mn,forming additional diffusion barrier layers,and by adding sulphur to modify oxide grain boundaries to reduce carbon diffusion along the grain boundaries.
文摘The oxidation of the ternary alloy Ni-15Cu-5Al in 1 × 105 Pa pure oxygen at 700 ℃ and 800 ℃ was studied. The results show that the behavior of the Ni-rich alloy is similar to that of the binary Ni-Al alloy with the same Al content in the form of an external NiO layer coupled to the internal oxidation of aluminium. The presence of 15%(mole fraction) Cu cannot modify substantially the values of relevant parameters affecting the transition from the internal to the external oxidation of aluminium. The presence of 5 % Al reduces the oxidation rate of the corresponding Ni-Cu alloy during the whole oxidation stages, though 5 % Al is still insufficient to form protective external alumina scales.
