Polyvinylidene fluoride/lead zirconate titanate(PVDF/PZT)composite films have been prepared by direct ink writing and the effect of PZT content on crystallization behavior and electrical properties of film were system...Polyvinylidene fluoride/lead zirconate titanate(PVDF/PZT)composite films have been prepared by direct ink writing and the effect of PZT content on crystallization behavior and electrical properties of film were systematically investigated.The composite films were characterized by scanning electron microscope(SEM),X-ray diffractometer(XRD),Flourier transform infrared spectroscope(FTIR)and differential scanning calorimeter(DSC).The results show that,surface modified PZT powder(PZT@PDA)is successfully coated by polydopamine(PDA),resulting in a large number of polar groups that interact with the-CF_(2)-groups in PVDF,inducing the generation of polarβphase due to hydrogen bonding formed in the interaction.Theβphase content in composite film increases with increasing PZT@PDA content,up to 28.09%as with 5 wt.%PZT@PDA.PZT@PDA plays a role of nucleating agent to promote the generation of polar phases in the film and also acts as an impurity hindering the growth of nuclei to reduce crystallinity.Moreover,the presence of PZT@PDA in interfaces provides more sites for the occurrence of interfacial polarization and thus improving the electrical properties of films.The composite film with 5 wt.%PZT@PDA possesses the highest dielectric constant(8.61)and residual polarization value(0.6803μC/cm^(2)).展开更多
ZnO-Bi2O3-based varistor ceramics doped with Yb2O3 in the range from 0 to 0.4% （molar fraction） were obtained by a solid reaction route. The X-ray diffractometry （XRD） and scanning electron microscopy （SEM） were...ZnO-Bi2O3-based varistor ceramics doped with Yb2O3 in the range from 0 to 0.4% （molar fraction） were obtained by a solid reaction route. The X-ray diffractometry （XRD） and scanning electron microscopy （SEM） were applied to characterize the phases and microstructure of the varistor ceramics, and a DC parameter instrument for varistor ceramics was applied to investigate their electrical properties and V-I characteristics. The XRD analysis of the samples shows that the ZnO phase, Bi2O3 phase, ZnTSbaOl2-type spinel phase and Zn2Bi3Sb3O14-type pyrochlore are present, and the Yb2O3 phases and Sb2O4 phases are found in varistor ceramics with increasing amounts of Yb2O3. The average size of ZnO grain firstly increases and then decreases with the increase of Yb2O3 content. The result also shows that the threshold voltage is between 656 V/nun and 1 232 V/mm, the nonlinear coefficient is in the range of 14.1-22.3, and the leakage current is between 0.60 μA and 19.6 μA. The 0.20% Yb2O3-added ZnO-Bi2O3-based varistor ceramics sintered at 900 ℃ have the best electrical characteristics.展开更多
Microstructure and electrical properties of La2 O3-doped ZnO-Bi2 O3 thin films prepared by sol–gel process have been investigated.X-ray diffraction shows that most diffraction peaks of ZnO are equal,and the crystals ...Microstructure and electrical properties of La2 O3-doped ZnO-Bi2 O3 thin films prepared by sol–gel process have been investigated.X-ray diffraction shows that most diffraction peaks of ZnO are equal,and the crystals of ZnO grow well.Scanning electron microscopy and atomic force microscopy results indicate that the samples have a good structure and lower surface roughness.The nonlinear V–I characteristics of the films show that La2 O3 develops the electrical properties largely and the best doped content is 0.3% lanthanum ion,with the leakage current of 0.25 mA,the threshold field of 150 V/mm and the nonlinear coefficient of 4.0 in detail.展开更多
The monitoring of cutting force in a vibration cutting process has a great significance in the popularization of ultrasonic vibration cutting technology. A new monitoring method of which the cutting force of ultrasoni...The monitoring of cutting force in a vibration cutting process has a great significance in the popularization of ultrasonic vibration cutting technology. A new monitoring method of which the cutting force of ultrasonic elliptic vibration cutting is monitored using the electrical properties of transducer was proposed by studying on the relationship of cutting force, transducer electric impedance and load. A measurement system was designed for the electrical properties of transducer. The feasibility of cutting force monitoring method based on the electrical properties of piezoelectric transducer was proved by the cutting experiments.展开更多
Due to their outstanding electrical contact properties,Cd-containing silver-matrix electrical contact materials can meet the requirements of high stability and long life for military defense and aerospace applications...Due to their outstanding electrical contact properties,Cd-containing silver-matrix electrical contact materials can meet the requirements of high stability and long life for military defense and aerospace applications.In order to further reduce the Cd content under the premise of meeting the high-performance requirements,in this study,high-purity intermediate Ti_(2)Cd powder of MAX phase(Ti_(2)CdC)was synthesized with a pressureless technique and then applied to reinforce the Ag matrix.The Cd content of the as-prepared Ag/Ti_(2)Cd composites was actually reduced by 38.31%compared with conventional Ag/CdO material.Based on the systematic study of the effect of heat treatment temperature on the physical phase,morphology,interface and comprehensive physical properties of Ag/Ti_(2)Cd composites,the preferred samples(heat treated at 400°C for 1 h)showed high density(97.77%),low resistivity(2.34μΩ·cm),moderate hardness(90.8HV),high tensile strength(189.9 MPa),and exhibited good electrical contact performance after 40000 cycles of arc discharging under severe conditions(DC 28 V/20 A).The results of microscopic morphological evolution,phase change and elemental distribution of the electrical contact surface show that the combination of high stability of Ti_(2)Cd reinforcing phase,good interfacial bonding with Ag matrix and improved melt pool viscosity in the primary stage of arc erosion,results in low and stable contact resistance(average value 13.20 mΩ)and welding force(average value 0.6 N),low fluctuation of static force(2.2-2.5 N).The decomposition and absorption energy of Ti_(2)Cd and the arc extinguishing effect of Cd vapor are the main reasons for the stable arcing energy and arcing time of electric contacts in the late stage of arc erosion.展开更多
Mechanical properties and microstructure of multifunctional composites produced with palm kernel shell ash nano particle(PKSAnp)-A356 alloy composites was studied.The composites were produced using Double layer feedin...Mechanical properties and microstructure of multifunctional composites produced with palm kernel shell ash nano particle(PKSAnp)-A356 alloy composites was studied.The composites were produced using Double layer feeding stir casting method(DLF-SCM) by adding 1 wt%-4 wt.% PKSAnp.The microstructure,density,electrical and mechanical properties were determined.The results shows that there was a uniform distribution of the PKSAnp in A356 alloy.The mismatch at the interface between the PKSAnp and A356 alloy was 4.26%.Improvement of 30.47%,41.91%,49.52%,40.90% and 65.09% were obtained for hardness values,tensile,yield strength,%elongation and impact energy at 4 wt% PKASnp.The work has established that the developed composites can be used for multifunctional applications where combination of toughness and strength is vital.展开更多
The effect of surface roughness of aluminum oxide (95%) substrate on the properties of Ni-Cr alloy thin film is studied.The thin films are prepared on the substrates with different roughness by using magnetron sputter...The effect of surface roughness of aluminum oxide (95%) substrate on the properties of Ni-Cr alloy thin film is studied.The thin films are prepared on the substrates with different roughness by using magnetron sputtering.The micro-structure,adhesive and electrical properties of the thin films were investigated by using scanning electron microscopy,scratch method and four-probe method.The burst voltage and current of the thin film transducers with different substrates were measured according to D-optimization method.The results show that the particle size,structural defect,resistivity and adhesion strength of the thin film increase with the increase of the substrate roughness.The difference among the burst time of the samples with difference substrate roughness gradually decreases with the increase of stimulation amount.The burst time is approximate to 20 μs in the charging voltage of 37 V.展开更多
In this study, we investigated the performance improvement caused by the addition of copper(Cu)nanoparticles to high-density polyethylene(HDPE) matrix material. Composite materials, with filler percentages of 0.0, 2.0...In this study, we investigated the performance improvement caused by the addition of copper(Cu)nanoparticles to high-density polyethylene(HDPE) matrix material. Composite materials, with filler percentages of 0.0, 2.0, 4.0, 6.0, 8.0, and 10.0 wt% were synthesized through the material extrusion(MEX)3D printing technique. The synthesized nanocomposite filaments were utilized for the manufacturing of specimens suitable for the experimental procedure that followed. Hence, we were able to systematically investigate their tensile, flexural, impact, and microhardness properties through various mechanical tests that were conducted according to the corresponding standards. Broadband Dielectric Spectroscopy was used to investigate the electrical/dielectric properties of the composites. Moreover, by employing means of Raman spectroscopy and thermogravimetric analysis(TGA) we were also able to further investigate their vibrational, structural, and thermal properties. Concomitantly, means of scanning electron microscopy(SEM), as well as atomic force microscopy(AFM), were used for the examination of the morphological and structural characteristics of the synthesized specimens, while energy-dispersive Xray spectroscopy(EDS) was also performed in order to receive a more detailed picture on the structural characteristics of the various synthesized composites. The corresponding nanomaterials were also assessed for their antibacterial properties regarding Staphylococcus aureus(S. aureus) and Escherichia coli(E. coli) with the assistance of a method named screening agar well diffusion. The results showed that the mechanical properties of HDPE benefited from the utilization of Cu as a filler, as they showed a notable improvement. The specimen of HDPE/Cu 4.0 wt% was the one that presented the highest levels of reinforcement in four out of the seven tested mechanical properties(for example, it exhibited a 36.7%improvement in the flexural strength, compared to the pure matrix). At the same time, the nanocomposites were efficient against the S. aureus bacterium and less efficient against the E. coli bacterium.The use of such multi-functional, robust nanocomposites in MEX 3D printing is positively impacting applications in various fields, most notably in the defense and security sectors. The latter becomes increasingly important if one takes into account that most firearms encompass various polymeric parts that require robustness and improved mechanical properties, while at the same time keeping the risk of spreading various infectious microorganisms at a bare minimum.展开更多
Finer nanoplates of silver are prepared by self-assembly on the surface of graphene,and the low-temperature sintered high conductivity ink containing the silver nanoplates is prepared.Most importantly,graphene is adde...Finer nanoplates of silver are prepared by self-assembly on the surface of graphene,and the low-temperature sintered high conductivity ink containing the silver nanoplates is prepared.Most importantly,graphene is added to the solution before the chemical reduction reaction occurs.Firstly,it is found that silver nanoplates have self-assembly phenomenon on the surface of graphene.Secondly,the Ag nano hexagonal platelets(AgNHPs)with small particle sizes(10 nm),narrow distribution and good dispersion are prepared.Especially,smaller sizes(10 nm)and narrower particle size distribution of AgNHPs particles can be easily controlled by using this process.Finally,the conductivity of the ink is excellent.For example,when the printed patterns were sintering at 150℃,the resistivity of the ink(GE:0.15 g/L)reached the minimum value of 2.2×10^-6 cm.And the resistivity value was 3.7×10^-6Ωcm,when it was sintered at 100℃ for 30 min.The conductive ink prepared can be used for the field of printing electronics as ink-jet printing ink.展开更多
The effect of different molar ratios of Y2O3 and Y（NO3）3 on the microstructure and electrical response of ZnO-Bi203-based varistor ceramics sintered at 1 000 ℃ was investigated, and the mechanism by which this dopi...The effect of different molar ratios of Y2O3 and Y（NO3）3 on the microstructure and electrical response of ZnO-Bi203-based varistor ceramics sintered at 1 000 ℃ was investigated, and the mechanism by which this doping improves the electrical characteristics of ZnO-Bi203-based varistor ceramics was discussed. With increasing amounts of Y（NO3）3 or Y2O3 in the starting composition, Y2O3, Sb204 and Y-containing Bi-rich phase form, and the average grain size significantly decreases. The average grain size significantly decreases as the contents of rare earth compounds of Y（NO3）3 or Y2O3 increase. The maximum value of the nonlinear coefficient is found at 0.16% Y（NO3）3 or 0.02% YaO3 （molar fraction） doped varistor ceramics, and there is an increase of 122% or 35% compared with the varistor ceramics without Y（NO3）3 or Y2O3. The threshold voltage VT of Y（NO3）3 and Y2O3 reaches at 1 460 V/mm and 1 035 V/ram, respectively. The results also show that varistor sample doped with Y（NO3）3 has a remarkably more homogeneous and denser microstructure in comparison to the sample doped with Y2O3.展开更多
This paper deals with the assessment of vibro-acoustic properties of a multifunctional carbon fiber reinfo rced panel manu factured by bulk infu sion,a modified resin film infusion process.The components of the epoxy ...This paper deals with the assessment of vibro-acoustic properties of a multifunctional carbon fiber reinfo rced panel manu factured by bulk infu sion,a modified resin film infusion process.The components of the epoxy resin were chosen to contrast the electrical insulating property and poor flame resistance of the epoxy resins impregnating carbon woven fabric.To confer electrical conductivity to the resin a percentage of 0.5 wt%of Multi-Wall Carbon Nanotubes(MWCNTs)was dispersed in the resin,whereas to increase flame resistance a percentage of 5 wt%of Glycidil Polyhedral Oligomeric Silsesquioxanes(GPOSS)was solubilized in the epoxy mixture.Furthermore,as hardener agents,a mixture of 4,4’-DiaminoDiphenyl Sulfone(DDS)(53.4 wt%)and Bis(3-Aminophenyl)Methyl Phosphine Oxide(BAMPO)(46.7 wt%)was used.The values of the electrical conductivity were found satisfactory enough,being4.02×10^(-2)S/m for the multifunctional resin and 1.39×10^(4)S/m for the in-plane conductivity of the panel,whereas the Limiting Oxygen Index(LOI)value of the multifunctional resin was found to increase from 27%to 36%.Considering these promising results,an experimental assessment of the vibro-acoustic properties of the manufactured multifunctional panel was also performed.The panel was tested mainly to evaluate its low-frequency vibration damping and sound insulation characteristics.The manufactured panel demonstrated an improved efficiency if compared to a baseline configuration,presenting almost the double modal damping and a gain of 10 dB on the global noise reduction.展开更多
Carbon quantum dots(CQDs),which contain a core structure composed of sp^(2)carbon,can be used as the reinforcing phase like graphene and carbon nanotubes in metal matrix.In this paper,the CQD/Cu composite material was...Carbon quantum dots(CQDs),which contain a core structure composed of sp^(2)carbon,can be used as the reinforcing phase like graphene and carbon nanotubes in metal matrix.In this paper,the CQD/Cu composite material was prepared by powder metallurgy method.The composite powder was prepared by molecular blending method and ball milling method at first,and then densified into bulk material by spark plasma sintering(SPS).X-ray diffraction,Raman spectroscopy,infrared spectroscopy,and nuclear magnetic resonance were employed to characterize the CQD synthesized under different temperature conditions,and then CQDs with a higher degree of sp^(2)were utilized as the reinforcement to prepare composite materials with different contents.Mechanical properties and electrical conductivity results show that the tensile strength of the 0.2 CQD/Cu composite material is~31%higher than that of the pure copper sample,and the conductivity of 0.4 CQD/Cu is~96%IACS,which is as high as pure copper.TEM and HRTEM results show that good interface bonding of CQD and copper grain is the key to maintaining high mechanical and electrical conductivity.This research provides an important foundation and direction for new carbon materials reinforced metal matrix composites.展开更多
基金Project(22020JJ4729)supported by the Natural Science Foundation of Hunan Province,China。
文摘Polyvinylidene fluoride/lead zirconate titanate(PVDF/PZT)composite films have been prepared by direct ink writing and the effect of PZT content on crystallization behavior and electrical properties of film were systematically investigated.The composite films were characterized by scanning electron microscope(SEM),X-ray diffractometer(XRD),Flourier transform infrared spectroscope(FTIR)and differential scanning calorimeter(DSC).The results show that,surface modified PZT powder(PZT@PDA)is successfully coated by polydopamine(PDA),resulting in a large number of polar groups that interact with the-CF_(2)-groups in PVDF,inducing the generation of polarβphase due to hydrogen bonding formed in the interaction.Theβphase content in composite film increases with increasing PZT@PDA content,up to 28.09%as with 5 wt.%PZT@PDA.PZT@PDA plays a role of nucleating agent to promote the generation of polar phases in the film and also acts as an impurity hindering the growth of nuclei to reduce crystallinity.Moreover,the presence of PZT@PDA in interfaces provides more sites for the occurrence of interfacial polarization and thus improving the electrical properties of films.The composite film with 5 wt.%PZT@PDA possesses the highest dielectric constant(8.61)and residual polarization value(0.6803μC/cm^(2)).
基金Project(BK2011243) supported by the Natural Science Foundation of Jiangsu Province,ChinaProject(2007DA10512711408) supported by the Visiting Scholarship of State Key Laboratory of Power Transmission Equipment & System Security and New Technology (Chongqing University),China+4 种基金Project(EIPE11204) supported by the State Key Laboratory of Electrical Insulation and Power Equipment,ChinaProject(KF201104) supported by the State Key Laboratory of New Ceramic and Fine Processing,ChinaProject(KFJJ201105) supported by the Opening Project of State Key Laboratory of Electronic Thin Films and Integrated Devices,ChinaProject(10KJD430002) supported by the Universities Natural Science Research Project of Jiangsu Province,ChinaProject(11JDG084) supported by the Research Foundation of Jiangsu University,China
文摘ZnO-Bi2O3-based varistor ceramics doped with Yb2O3 in the range from 0 to 0.4% （molar fraction） were obtained by a solid reaction route. The X-ray diffractometry （XRD） and scanning electron microscopy （SEM） were applied to characterize the phases and microstructure of the varistor ceramics, and a DC parameter instrument for varistor ceramics was applied to investigate their electrical properties and V-I characteristics. The XRD analysis of the samples shows that the ZnO phase, Bi2O3 phase, ZnTSbaOl2-type spinel phase and Zn2Bi3Sb3O14-type pyrochlore are present, and the Yb2O3 phases and Sb2O4 phases are found in varistor ceramics with increasing amounts of Yb2O3. The average size of ZnO grain firstly increases and then decreases with the increase of Yb2O3 content. The result also shows that the threshold voltage is between 656 V/nun and 1 232 V/mm, the nonlinear coefficient is in the range of 14.1-22.3, and the leakage current is between 0.60 μA and 19.6 μA. The 0.20% Yb2O3-added ZnO-Bi2O3-based varistor ceramics sintered at 900 ℃ have the best electrical characteristics.
基金Project(20123227120021)supported by the Specialized Research Fund for the Doctoral Program of Higher Education of ChinaProject(BK2012156)supported by the Natural Science Foundation of Jiangsu Province,China+3 种基金Project(KFJJ201105)supported by the Opening Project of State Key Laboratory of Electronic Thin Films and Integrated Devices,ChinaProject(CJ20125001)supported by the Application Program for Basic Research of Changzhou,ChinaProject(13KJB430006)supported by the Universities Natural Science Research project of Jiangsu Province,ChinaProject supported by the Industrial Center of Jiangsu University Undergraduate Practice-Innovation Training Program,China
文摘Microstructure and electrical properties of La2 O3-doped ZnO-Bi2 O3 thin films prepared by sol–gel process have been investigated.X-ray diffraction shows that most diffraction peaks of ZnO are equal,and the crystals of ZnO grow well.Scanning electron microscopy and atomic force microscopy results indicate that the samples have a good structure and lower surface roughness.The nonlinear V–I characteristics of the films show that La2 O3 develops the electrical properties largely and the best doped content is 0.3% lanthanum ion,with the leakage current of 0.25 mA,the threshold field of 150 V/mm and the nonlinear coefficient of 4.0 in detail.
文摘The monitoring of cutting force in a vibration cutting process has a great significance in the popularization of ultrasonic vibration cutting technology. A new monitoring method of which the cutting force of ultrasonic elliptic vibration cutting is monitored using the electrical properties of transducer was proposed by studying on the relationship of cutting force, transducer electric impedance and load. A measurement system was designed for the electrical properties of transducer. The feasibility of cutting force monitoring method based on the electrical properties of piezoelectric transducer was proved by the cutting experiments.
基金This work was financially supported by the National Natural Science Foundation of China(52101064)Jiangsu Planned Projects for Postdoctoral Research Funds(2020Z158)Industry-University-Research Cooperation Projects(RH2000002728,RH2000002332,RH2100000263).
文摘Due to their outstanding electrical contact properties,Cd-containing silver-matrix electrical contact materials can meet the requirements of high stability and long life for military defense and aerospace applications.In order to further reduce the Cd content under the premise of meeting the high-performance requirements,in this study,high-purity intermediate Ti_(2)Cd powder of MAX phase(Ti_(2)CdC)was synthesized with a pressureless technique and then applied to reinforce the Ag matrix.The Cd content of the as-prepared Ag/Ti_(2)Cd composites was actually reduced by 38.31%compared with conventional Ag/CdO material.Based on the systematic study of the effect of heat treatment temperature on the physical phase,morphology,interface and comprehensive physical properties of Ag/Ti_(2)Cd composites,the preferred samples(heat treated at 400°C for 1 h)showed high density(97.77%),low resistivity(2.34μΩ·cm),moderate hardness(90.8HV),high tensile strength(189.9 MPa),and exhibited good electrical contact performance after 40000 cycles of arc discharging under severe conditions(DC 28 V/20 A).The results of microscopic morphological evolution,phase change and elemental distribution of the electrical contact surface show that the combination of high stability of Ti_(2)Cd reinforcing phase,good interfacial bonding with Ag matrix and improved melt pool viscosity in the primary stage of arc erosion,results in low and stable contact resistance(average value 13.20 mΩ)and welding force(average value 0.6 N),low fluctuation of static force(2.2-2.5 N).The decomposition and absorption energy of Ti_(2)Cd and the arc extinguishing effect of Cd vapor are the main reasons for the stable arcing energy and arcing time of electric contacts in the late stage of arc erosion.
基金The authors would like to acknowledge Tertiary Education Trust Fund(TETFund)Nigeria for providing financial aid for this project under the project number:TETFUND/DESS/UNI/NSUKKA/2017/RP/VOL.I.
文摘Mechanical properties and microstructure of multifunctional composites produced with palm kernel shell ash nano particle(PKSAnp)-A356 alloy composites was studied.The composites were produced using Double layer feeding stir casting method(DLF-SCM) by adding 1 wt%-4 wt.% PKSAnp.The microstructure,density,electrical and mechanical properties were determined.The results shows that there was a uniform distribution of the PKSAnp in A356 alloy.The mismatch at the interface between the PKSAnp and A356 alloy was 4.26%.Improvement of 30.47%,41.91%,49.52%,40.90% and 65.09% were obtained for hardness values,tensile,yield strength,%elongation and impact energy at 4 wt% PKASnp.The work has established that the developed composites can be used for multifunctional applications where combination of toughness and strength is vital.
文摘The effect of surface roughness of aluminum oxide (95%) substrate on the properties of Ni-Cr alloy thin film is studied.The thin films are prepared on the substrates with different roughness by using magnetron sputtering.The micro-structure,adhesive and electrical properties of the thin films were investigated by using scanning electron microscopy,scratch method and four-probe method.The burst voltage and current of the thin film transducers with different substrates were measured according to D-optimization method.The results show that the particle size,structural defect,resistivity and adhesion strength of the thin film increase with the increase of the substrate roughness.The difference among the burst time of the samples with difference substrate roughness gradually decreases with the increase of stimulation amount.The burst time is approximate to 20 μs in the charging voltage of 37 V.
文摘In this study, we investigated the performance improvement caused by the addition of copper(Cu)nanoparticles to high-density polyethylene(HDPE) matrix material. Composite materials, with filler percentages of 0.0, 2.0, 4.0, 6.0, 8.0, and 10.0 wt% were synthesized through the material extrusion(MEX)3D printing technique. The synthesized nanocomposite filaments were utilized for the manufacturing of specimens suitable for the experimental procedure that followed. Hence, we were able to systematically investigate their tensile, flexural, impact, and microhardness properties through various mechanical tests that were conducted according to the corresponding standards. Broadband Dielectric Spectroscopy was used to investigate the electrical/dielectric properties of the composites. Moreover, by employing means of Raman spectroscopy and thermogravimetric analysis(TGA) we were also able to further investigate their vibrational, structural, and thermal properties. Concomitantly, means of scanning electron microscopy(SEM), as well as atomic force microscopy(AFM), were used for the examination of the morphological and structural characteristics of the synthesized specimens, while energy-dispersive Xray spectroscopy(EDS) was also performed in order to receive a more detailed picture on the structural characteristics of the various synthesized composites. The corresponding nanomaterials were also assessed for their antibacterial properties regarding Staphylococcus aureus(S. aureus) and Escherichia coli(E. coli) with the assistance of a method named screening agar well diffusion. The results showed that the mechanical properties of HDPE benefited from the utilization of Cu as a filler, as they showed a notable improvement. The specimen of HDPE/Cu 4.0 wt% was the one that presented the highest levels of reinforcement in four out of the seven tested mechanical properties(for example, it exhibited a 36.7%improvement in the flexural strength, compared to the pure matrix). At the same time, the nanocomposites were efficient against the S. aureus bacterium and less efficient against the E. coli bacterium.The use of such multi-functional, robust nanocomposites in MEX 3D printing is positively impacting applications in various fields, most notably in the defense and security sectors. The latter becomes increasingly important if one takes into account that most firearms encompass various polymeric parts that require robustness and improved mechanical properties, while at the same time keeping the risk of spreading various infectious microorganisms at a bare minimum.
基金Project(2018GK4015)supported by the Hunan Provincial Strategic Emerging Industry Project,China
文摘Finer nanoplates of silver are prepared by self-assembly on the surface of graphene,and the low-temperature sintered high conductivity ink containing the silver nanoplates is prepared.Most importantly,graphene is added to the solution before the chemical reduction reaction occurs.Firstly,it is found that silver nanoplates have self-assembly phenomenon on the surface of graphene.Secondly,the Ag nano hexagonal platelets(AgNHPs)with small particle sizes(10 nm),narrow distribution and good dispersion are prepared.Especially,smaller sizes(10 nm)and narrower particle size distribution of AgNHPs particles can be easily controlled by using this process.Finally,the conductivity of the ink is excellent.For example,when the printed patterns were sintering at 150℃,the resistivity of the ink(GE:0.15 g/L)reached the minimum value of 2.2×10^-6 cm.And the resistivity value was 3.7×10^-6Ωcm,when it was sintered at 100℃ for 30 min.The conductive ink prepared can be used for the field of printing electronics as ink-jet printing ink.
基金Project(BK2011243) supported by the Natural Science Foundation of Jiangsu Province, ChinaProject(EIPE11204) supported by the State Key Laboratory of Electrical Insulation and Power Equipment, China+4 种基金Project(KF201104) supported by the State Key Laboratory of New Ceramic and Fine Processing, ChinaProject(KFJJ201105) supported by the Opening Program of State key Laboratory of Electronic Thin Films and Integrated Devices, ChinaProject(2011-22) supported by the State Key Laboratory of Inorganic Synthesis and Preparative Chemistry of Jilin University, ChinaProject(10KJD430002) supported by the Universities Natural Science Research Project of Jiangsu Province, ChinaProject(11JDG084) supported by the Research Foundation of Jiangsu University, China
文摘The effect of different molar ratios of Y2O3 and Y（NO3）3 on the microstructure and electrical response of ZnO-Bi203-based varistor ceramics sintered at 1 000 ℃ was investigated, and the mechanism by which this doping improves the electrical characteristics of ZnO-Bi203-based varistor ceramics was discussed. With increasing amounts of Y（NO3）3 or Y2O3 in the starting composition, Y2O3, Sb204 and Y-containing Bi-rich phase form, and the average grain size significantly decreases. The average grain size significantly decreases as the contents of rare earth compounds of Y（NO3）3 or Y2O3 increase. The maximum value of the nonlinear coefficient is found at 0.16% Y（NO3）3 or 0.02% YaO3 （molar fraction） doped varistor ceramics, and there is an increase of 122% or 35% compared with the varistor ceramics without Y（NO3）3 or Y2O3. The threshold voltage VT of Y（NO3）3 and Y2O3 reaches at 1 460 V/mm and 1 035 V/ram, respectively. The results also show that varistor sample doped with Y（NO3）3 has a remarkably more homogeneous and denser microstructure in comparison to the sample doped with Y2O3.
文摘This paper deals with the assessment of vibro-acoustic properties of a multifunctional carbon fiber reinfo rced panel manu factured by bulk infu sion,a modified resin film infusion process.The components of the epoxy resin were chosen to contrast the electrical insulating property and poor flame resistance of the epoxy resins impregnating carbon woven fabric.To confer electrical conductivity to the resin a percentage of 0.5 wt%of Multi-Wall Carbon Nanotubes(MWCNTs)was dispersed in the resin,whereas to increase flame resistance a percentage of 5 wt%of Glycidil Polyhedral Oligomeric Silsesquioxanes(GPOSS)was solubilized in the epoxy mixture.Furthermore,as hardener agents,a mixture of 4,4’-DiaminoDiphenyl Sulfone(DDS)(53.4 wt%)and Bis(3-Aminophenyl)Methyl Phosphine Oxide(BAMPO)(46.7 wt%)was used.The values of the electrical conductivity were found satisfactory enough,being4.02×10^(-2)S/m for the multifunctional resin and 1.39×10^(4)S/m for the in-plane conductivity of the panel,whereas the Limiting Oxygen Index(LOI)value of the multifunctional resin was found to increase from 27%to 36%.Considering these promising results,an experimental assessment of the vibro-acoustic properties of the manufactured multifunctional panel was also performed.The panel was tested mainly to evaluate its low-frequency vibration damping and sound insulation characteristics.The manufactured panel demonstrated an improved efficiency if compared to a baseline configuration,presenting almost the double modal damping and a gain of 10 dB on the global noise reduction.
基金Project(52064032)supported by the National Natural Science Foundation of ChinaProjects(2019ZE001,202002AB080001)supported by the Yunnan Science and Technology Projects,ChinaProject(YNWR-QNBJ-2018-005)supported by the Yunnan Ten Thousand Talents Plan Young&Elite Talents,China。
文摘Carbon quantum dots(CQDs),which contain a core structure composed of sp^(2)carbon,can be used as the reinforcing phase like graphene and carbon nanotubes in metal matrix.In this paper,the CQD/Cu composite material was prepared by powder metallurgy method.The composite powder was prepared by molecular blending method and ball milling method at first,and then densified into bulk material by spark plasma sintering(SPS).X-ray diffraction,Raman spectroscopy,infrared spectroscopy,and nuclear magnetic resonance were employed to characterize the CQD synthesized under different temperature conditions,and then CQDs with a higher degree of sp^(2)were utilized as the reinforcement to prepare composite materials with different contents.Mechanical properties and electrical conductivity results show that the tensile strength of the 0.2 CQD/Cu composite material is~31%higher than that of the pure copper sample,and the conductivity of 0.4 CQD/Cu is~96%IACS,which is as high as pure copper.TEM and HRTEM results show that good interface bonding of CQD and copper grain is the key to maintaining high mechanical and electrical conductivity.This research provides an important foundation and direction for new carbon materials reinforced metal matrix composites.
