期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
Numerical simulation and analysis of solid-liquid two-phase threedimensional unsteady flow in centrifugal slurry pump 被引量:17
1
作者 吴波 汪西力 +1 位作者 LIU Hui 徐海良 《Journal of Central South University》 SCIE EI CAS CSCD 2015年第8期3008-3016,共9页
Based on RNG k-ε turbulence model and sliding grid technique, solid-liquid two-phase three-dimensional(3-D) unsteady turbulence of full passage in slurry pump was simulated by means of Fluent software. The effects of... Based on RNG k-ε turbulence model and sliding grid technique, solid-liquid two-phase three-dimensional(3-D) unsteady turbulence of full passage in slurry pump was simulated by means of Fluent software. The effects of unsteady flow characteristics on solid-liquid two-phase flow and pump performance were researched under design condition. The results show that clocking effect has a significant influence on the flow in pump, and the fluctuation of flow velocity and pressure is obvious, particularly near the volute tongue, at the position of small sections of volute and within diffuser. Clocking effect has a more influence on liquid-phase than on solid-phase, and the wake-jet structure of relative velocity of solid-phase is less obvious than liquid-phase near the volute tongue and the impeller passage outlet. The fluctuation of relative velocity of solid-phase flow is 7.6% smaller than liquid-phase flow at the impeller outlet on circular path. Head and radial forces of the impeller are 8.1% and 85.7% of fluctuation, respectively. The results provide a theoretical basis for further research for turbulence, improving efficient, reducing the hydraulic losses and wear. Finally, field tests were carried out to verify the operation and wear of slurry pump. 展开更多
关键词 slurry pump solid-liquid two-phase flow unsteady flow 3-d full passage numerical simulation
在线阅读 下载PDF
离心风机现代设计方法研究 被引量:26
2
作者 朱之墀 黄东涛 +1 位作者 边晓东 卢钰 《中国机械工程》 EI CAS CSCD 北大核心 1998年第8期54-56,共3页
提出一种新的离心风机现代设计方法,它包含3部分内容:①以现有的工程设计为基础;②利用正在发展的技术来进行离心风机气动力优化设计局用现场性能试验进行考核。其中,关键和难点是三维粘性流场数值模拟。按此方法研制出多种样机,气... 提出一种新的离心风机现代设计方法,它包含3部分内容:①以现有的工程设计为基础;②利用正在发展的技术来进行离心风机气动力优化设计局用现场性能试验进行考核。其中,关键和难点是三维粘性流场数值模拟。按此方法研制出多种样机,气动和噪声性能均有明显提高,证实这种方法是正确的。 展开更多
关键词 离心风机优化设计 数值模拟 三维粘性流场分析
在线阅读 下载PDF
轴流压气机级内三维粘性流动的数值模拟 被引量:3
3
作者 高丽敏 陈璇 +1 位作者 白莹 冯旭栋 《应用力学学报》 CAS CSCD 北大核心 2013年第4期569-573,648-649,共5页
考虑轴流压气机中实际气流沿径向和周向都不均匀的特点,采用亚松弛方法改进传统的混合界面模型,发展了轴流式压气机级内全三维粘性流场的数值计算程序,并以某轴流式双排对转压气机的进口导叶/转子为研究对象,将本文发展的程序与商用NUM... 考虑轴流压气机中实际气流沿径向和周向都不均匀的特点,采用亚松弛方法改进传统的混合界面模型,发展了轴流式压气机级内全三维粘性流场的数值计算程序,并以某轴流式双排对转压气机的进口导叶/转子为研究对象,将本文发展的程序与商用NUMECA软件的结果进行对比,对本文发展的程序进行了验证。对比结果表明:由于混合界面法引入了"人工掺混",商业软件计算得出的总压在通过交界面时存在一定的总压损失,而自编程序计算结果保证了总压在交界面处的一致性。流场分析结果表明:该转子叶片在设计工况下处于负攻角状态,在导叶出口轮毂处、压力面50%弦长处、吸力面靠近尾缘处均出现了轻微的流动分离现象。 展开更多
关键词 轴流压气机级 三维粘性计算 进口导叶 混合界面 动静干涉
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部