To address the problems of low accuracy by the CONWEP model and poor efficiency by the Coupled Eulerian-Lagrangian(CEL)method in predicting close-range air blast loads of cylindrical charges,a neural network-based sim...To address the problems of low accuracy by the CONWEP model and poor efficiency by the Coupled Eulerian-Lagrangian(CEL)method in predicting close-range air blast loads of cylindrical charges,a neural network-based simulation(NNS)method with higher accuracy and better efficiency was proposed.The NNS method consisted of three main steps.First,the parameters of blast loads,including the peak pressures and impulses of cylindrical charges with different aspect ratios(L/D)at different stand-off distances and incident angles were obtained by two-dimensional numerical simulations.Subsequently,incident shape factors of cylindrical charges with arbitrary aspect ratios were predicted by a neural network.Finally,reflected shape factors were derived and implemented into the subroutine of the ABAQUS code to modify the CONWEP model,including modifications of impulse and overpressure.The reliability of the proposed NNS method was verified by related experimental results.Remarkable accuracy improvement was acquired by the proposed NNS method compared with the unmodified CONWEP model.Moreover,huge efficiency superiority was obtained by the proposed NNS method compared with the CEL method.The proposed NNS method showed good accuracy when the scaled distance was greater than 0.2 m/kg^(1/3).It should be noted that there is no need to generate a new dataset again since the blast loads satisfy the similarity law,and the proposed NNS method can be directly used to simulate the blast loads generated by different cylindrical charges.The proposed NNS method with high efficiency and accuracy can be used as an effective method to analyze the dynamic response of structures under blast loads,and it has significant application prospects in designing protective structures.展开更多
A stuck drill string results in a major non-productive cost in extended reach drilling engineering. The first step is to determine the depth at which the sticking has occurred. Methods of measurement have been proved ...A stuck drill string results in a major non-productive cost in extended reach drilling engineering. The first step is to determine the depth at which the sticking has occurred. Methods of measurement have been proved useful for determining the stuck points, but these operations take considerable time. As a result of the limitation with the current operational practices, calculation methods are still preferred to estimate the stuck point depth. Current analytical methods do not consider friction and are only valid for vertical rather than extended reach wells. The numerical method is established to take full account of down hole friction, tool joint, upset end of drill pipe, combination drill strings and tubular materials so that it is valid to determine the stuck point in extended reach wells. The pull test, torsion test and combined test of rotation and pulling can be used to determine the stuck point. The results show that down hole friction, tool joint, upset end of drill pipe, tubular sizes and materials have significant effects on the pull length and/or the twist angle of the stuck drill string.展开更多
The purpose of this study was to investigate the effect of bolt profile on load transfer mechanism of fully grouted bolts in jointed rocks using analytical and numerical methods. Based on the analytical method with de...The purpose of this study was to investigate the effect of bolt profile on load transfer mechanism of fully grouted bolts in jointed rocks using analytical and numerical methods. Based on the analytical method with development of methods, a new model is presented. To validate the analytical model, five different profiles modeled by ANSYS software. The profile of rock bolts T3 and T4with load transfer capacity,respectively 180 and 195 kN in the jointed rocks was selected as the optimum profiles. Finally, the selected profiles were examined in Tabas Coal Mine. FLAC analysis indicates that patterns 6+7 with2 NO flexi bolt 4 m better than other patterns within the faulted zone.展开更多
Although the nonlinear interactions between a single short gravity wave and a long wave can be solved analytically, the solution is less tractable in more general cases involving multiple short waves. In this work we ...Although the nonlinear interactions between a single short gravity wave and a long wave can be solved analytically, the solution is less tractable in more general cases involving multiple short waves. In this work we present a numerical method of studying nonlinear interactions between a long wave and multiple short harmonic waves in infinitely deep water. Specifically, this method is applied to the calculation of the temporal and spatial evolutions of the surface elevations in which a given long wave interacts with several short harmonic waves. Another important application of our method is to quantitatively analyse the nonlinear interactions between an arbitrary short wave train and another short wave train. From simulation results, we obtain that the mechanism for the nonlinear interactions between one short wave train and another short wave train （expressed as wave train 2） leads to the energy focusing of the other short wave train （expressed as wave train 3）. This mechanism occurs on wave components with a narrow frequency bandwidth, whose frequencies are near that of wave train 3.展开更多
An 8-channel HCN laser interferometer will be installed on HL-2A in near term. In order to get the spatial profile of the electron density Barr numerical method is adopted to realize the Abel inversion. In this articl...An 8-channel HCN laser interferometer will be installed on HL-2A in near term. In order to get the spatial profile of the electron density Barr numerical method is adopted to realize the Abel inversion. In this article the result of the Abel inversion by Matlab GUI is given which can be updated to process the measured data of the 8-channel laser interferometer and provide the spatial distribution of the electron density.展开更多
We propose a high-order conservative method for the nonlinear Sehodinger/Gross-Pitaevskii equation with time- varying coefficients in modeling Bose Einstein condensation （BEC）. This scheme combined with the sixth-or...We propose a high-order conservative method for the nonlinear Sehodinger/Gross-Pitaevskii equation with time- varying coefficients in modeling Bose Einstein condensation （BEC）. This scheme combined with the sixth-order compact finite difference method and the fourth-order average vector field method, finely describes the condensate wave function and physical characteristics in some small potential wells. Numerical experiments are presented to demonstrate that our numerical scheme is efficient by the comparison with the Fourier pseudo-spectral method. Moreover, it preserves several conservation laws well and even exactly under some specific conditions.展开更多
A new provement of the existence and uniqueness about periodic boundary value Duffing equation is established by using global inverse function theorem. An algorithm for solving differential equation that has a large c...A new provement of the existence and uniqueness about periodic boundary value Duffing equation is established by using global inverse function theorem. An algorithm for solving differential equation that has a large convergence domain is given. Finally, a numerical example is given.展开更多
One of the critical aspects in mine design is slope stability analysis and the determination of stable slopes. In the Chador- Malu iron ore mine, one of the most important iron ore mines in central Iran, it was consid...One of the critical aspects in mine design is slope stability analysis and the determination of stable slopes. In the Chador- Malu iron ore mine, one of the most important iron ore mines in central Iran, it was considered vital to perform a comprehensive slope stability analysis. At first, we divided the existing rock hosting pit into six zones and a geotechnical map was prepared. Then, the value of MRMR （Mining Rock Mass Rating） was determined for each zone. Owing to the fact that the Chador-Malu iron ore mine is located in a highly tectonic area and the rock mass completely crushed, the Hoek-Brown failure criterion was found suitable to estimate geo-mechanical parameters. After that, the value of cohesion （c） and friction angle （tp） were calculated for different geotechnical zones and relative graphs and equations were derived as a function of slope height. The stability analyses using numerical and limit equilibrium methods showed that some instability problems might occur by increasing the slope height. Therefore, stable slopes for each geotechnical zone and prepared sections were calculated and presented as a function of slope height.展开更多
A numerical method is proposed to calculate the eigenvalues of the Zakharov–Shabat system based on Chebyshev polynomials. A mapping in the form of tanh(ax) is constructed according to the asymptotic of the potential ...A numerical method is proposed to calculate the eigenvalues of the Zakharov–Shabat system based on Chebyshev polynomials. A mapping in the form of tanh(ax) is constructed according to the asymptotic of the potential function for the Zakharov–Shabat eigenvalue problem. The mapping can distribute Chebyshev nodes very well considering the gradient for the potential function. Using Chebyshev polynomials, tanh(ax) mapping, and Chebyshev nodes, the Zakharov–Shabat eigenvalue problem is transformed into a matrix eigenvalue problem. This method has good convergence for the Satsuma–Yajima potential and the convergence rate is faster than the Fourier collocation method. This method is not only suitable for simple potential functions but also converges quickly for a complex Y-shape potential. It can also be further extended to other linear eigenvalue problems.展开更多
In this paper, by means of the maximum circle tensile stress on curve of constant ω and stress intensity factors by a path independent contour integral method, trajectories of maxed mode crack propagation are simulat...In this paper, by means of the maximum circle tensile stress on curve of constant ω and stress intensity factors by a path independent contour integral method, trajectories of maxed mode crack propagation are simulated through numerical manifold method. The crack propagation is traced dynamically by modifying the neighboring connection between the crack-top and nodes within elements in the calculating process. This method has the advantages such as less modified area, easiness of programming, high realizability and so on. Then a single sharp nicked specimen is used to verified the numerical result. It is shown that the provided method is reasonable and effective.展开更多
Based on the principle of equivalent phase comparison frequency, we propose a group-period phase comparison method. This method can be used to reveal the inherent relations between periodic signals and the change laws...Based on the principle of equivalent phase comparison frequency, we propose a group-period phase comparison method. This method can be used to reveal the inherent relations between periodic signals and the change laws of the phase difference. If these laws are applied in the processing of the mutual relations between frequency signals, phase comparison can be accomplished without frequency normalization. Experimental results show that the method can enhance the measurement resolution to 10-13/s in the time domain.展开更多
Based on the principle of quantized delay-time, a super-high resolution time interval measurement method is proposed based on time-space relationships. Using the delay-time stability that time and frequency signal tra...Based on the principle of quantized delay-time, a super-high resolution time interval measurement method is proposed based on time-space relationships. Using the delay-time stability that time and frequency signal travel in a specific medium, the measured time interval can be quantized. Combined with the phase coincidence detection technique, the measurement of time can be changed into the measurement of space length. The resolution and the stability of the measurement system are easily improved. Experimental results show that the measurement resolution of the measured time interval depends on the length difference of the double delay-time unit. When the length difference is set up on millimeter level or sub-millimeter level, super-high measurement resolution from hundreds of picosecond to tens of picosecond can be obtained.展开更多
Based on the particle-in-cell technology and the secondary electron emission theory, a three-dimensional simulation method for multipactor is presented in this paper. By combining the finite difference time domain met...Based on the particle-in-cell technology and the secondary electron emission theory, a three-dimensional simulation method for multipactor is presented in this paper. By combining the finite difference time domain method and the panicle tracing method, such an algorithm is self-consistent and accurate since the interaction between electromagnetic fields and particles is properly modeled. In the time domain aspect, the generation of multipactor can be easily visualized, which makes it possible to gain a deeper insight into the physical mechanism of this effect. In addition to the classic secondary electron emission model, the measured practical secondary electron yield is used, which increases the accuracy of the algorithm. In order to validate the method, the impedance transformer and ridge waveguide filter are studied. By analyzing the evolution of the secondaries obtained by our method, multipactor thresholds of these components are estimated, which show good agreement with the experimental results. Furthermore, the most sensitive positions where multipactor occurs are determined from the phase focusing phenomenon, which is very meaningful for multipactor analysis and design.展开更多
A plane mechanical model of rock breaking process by double disc cutter at the center of the cutterhead is established based on contact mechanics to analyze the stress evolution in the rock broken by cutters with diff...A plane mechanical model of rock breaking process by double disc cutter at the center of the cutterhead is established based on contact mechanics to analyze the stress evolution in the rock broken by cutters with different spacings. A continuous-discontinuous coupling numerical method based on zero-thickness cohesive elements is developed to simulate rock breaking using double cutters. The process, mechanism,and characteristics of rock breaking are comprehensively analyzed from five aspects: peak force, breaking form, breaking efficiency, crack mode, and breaking degree. The results show that under the penetrating action of cutters, dense cores are formed due to shear failure under respective cutters. The tensile cracks propagate in the rock, and then rock chips form with increasing penetration depth. When the cutter spacing is increased from 10 to 80 mm, the peak force gradually increases, the rock breaking range increases first and then decreases, the specific energy decreases first and then rises, and the breaking coefficient of intermediate rock decreases from 0.955 to 0.788. The area of rock breaking is positively correlated with the length of the tensile crack. Furthermore, the length of the tensile crack accounts for 14.4%–33.6% of the total crack length.展开更多
An all-optical encryption-decryption method using an exclusive-or gate based on the cross-phase modulation between O-band and C-band light waves is proposed. The feasibility of the encryptionecryption technique is ver...An all-optical encryption-decryption method using an exclusive-or gate based on the cross-phase modulation between O-band and C-band light waves is proposed. The feasibility of the encryptionecryption technique is verified by handling binary signals at 2.5 Gbps, with less than 3dB penalty of extinction ratio and i dB polarization dependent loss.展开更多
The imaginary time step （ITS） method is applied to solve the Dirac equation with the nonlocal potential in coordinate space by the ITS evolution for the corresponding Schrfdinger-like equation for the upper componen...The imaginary time step （ITS） method is applied to solve the Dirac equation with the nonlocal potential in coordinate space by the ITS evolution for the corresponding Schrfdinger-like equation for the upper component. It is demonstrated that the ITS evolution can be equivalently performed for the Schrodinger-like equation with or without localization. The latter algorithm is recommended in the application for the reason of simplicity and efficiency. The feasibility and reliability of this algorithm are also illustrated by taking the nucleus ^16O as an example, where the same results as the shooting method for the Dirae equation with localized effective potentials are obtained.展开更多
The finite volume method has been successfully applied in several engineering fields and has shown outstanding performance in fluid dynamics simulation. In this paper, the general framework for the simulation ofnear-w...The finite volume method has been successfully applied in several engineering fields and has shown outstanding performance in fluid dynamics simulation. In this paper, the general framework for the simulation ofnear-wellbore systems using the finite volume method is described. The mathematical model and the numerical model developed by the authors are presented and discussed. A radial geometry in the vertical plane was implemented so as to thoroughly describe near-wellbore phenomena. The model was then used to simulate injection tests in an oil reservoir through a horizontal well and proved very powerful to correctly reproduce the transient pressure behavior. The reason for this is the robustness of the method, which is independent of the gridding options because the discretization is performed in the physical space. The model is able to describe the phenomena taking place in the reservoir even in complex situations, i.e. in the presence of heterogeneities and permeability barriers, demonstrating the flexibility of the finite volume method when simulating non-conventional tests. The results are presented in comparison with those obtained with the finite difference numerical approach and with analytical methods, if possible.展开更多
This paper studies numerically the thermo-mechanical effects of ZrO2 thermal barrier coatings （TBCs） irradiated by a high-intensity pulsed ion beam in consideration of the surface structure. Taking the deposited ene...This paper studies numerically the thermo-mechanical effects of ZrO2 thermal barrier coatings （TBCs） irradiated by a high-intensity pulsed ion beam in consideration of the surface structure. Taking the deposited energy of ion beams in TBCs as the source term in the thermal conduction equation, the distribution of temperature in TBCs was simulated. Then, based on the distribution, the evolution of thermal stress was calculated by the finite element method. The results show that tensile radial stress formed at the valley of TBC surfaces after irradiation by HIPIB. Therefore, if cracks happen, they must be at valleys instead of peaks. As for the stress waves, no matter whether through peak or valley position, tensile and compressive stresses are present alternately inside TBCs along the depth direction, and the strength of stress decreases with time.展开更多
The transient thermoelastic stress fields of GaN films is analyzed by the finite element method for the laser lift-off （LLO） technique. Stress distributions in GaN films irradiated by pulse laser with different ener...The transient thermoelastic stress fields of GaN films is analyzed by the finite element method for the laser lift-off （LLO） technique. Stress distributions in GaN films irradiated by pulse laser with different energy densities as functions of time and depth are simulated. The results show that the high thermoelastic stress distributions in GaN films localize within about 1 μm below the GaN/Al2O3 interface using proper laser parameters. It is also found that GaN films can avoid the thermal deformation because the maximum thermoelastic stress 4.28 GPa is much smaller than the yield strength of GaN 15GPa. The effects of laser beam dimension and the thickness of GaN films on stress distribution are also analyzed. The variation range of laser beam dimension as a function of the thickness of GaN films is simulated to keep the GaN films free of thermal deformation. LLO experiments are also carried out. GaN-based light-emitting diodes （LEDs） are separated from sapphire substrates using the parameters obtained from the simulation. Compared with devices before LLO, P-I-V measurements of GaN- based LEDs after LLO show that the electrical and optical characteristics improve greatly, indicating that no stress damage is brought to GaN films using proper parameters obtained by calculation during LLO.展开更多
We investigate the self-heating effect of mid-infrared quantum cascade lasers by using a direct-based pulse injecting current and spectroscopy method. Based on the characterization system, the thermal characteristics ...We investigate the self-heating effect of mid-infrared quantum cascade lasers by using a direct-based pulse injecting current and spectroscopy method. Based on the characterization system, the thermal characteristics of gas source MBE grown 8.4μm InP-based GalnAs/AIInAs DFB-QCLs are evaluated. The method and characterization system are also useful in evaluating the thermal characteristics of other types of mid-infrared diode lasers.展开更多
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52271317 and 52071149)the Fundamental Research Funds for the Central Universities(HUST:2019kfy XJJS007)。
文摘To address the problems of low accuracy by the CONWEP model and poor efficiency by the Coupled Eulerian-Lagrangian(CEL)method in predicting close-range air blast loads of cylindrical charges,a neural network-based simulation(NNS)method with higher accuracy and better efficiency was proposed.The NNS method consisted of three main steps.First,the parameters of blast loads,including the peak pressures and impulses of cylindrical charges with different aspect ratios(L/D)at different stand-off distances and incident angles were obtained by two-dimensional numerical simulations.Subsequently,incident shape factors of cylindrical charges with arbitrary aspect ratios were predicted by a neural network.Finally,reflected shape factors were derived and implemented into the subroutine of the ABAQUS code to modify the CONWEP model,including modifications of impulse and overpressure.The reliability of the proposed NNS method was verified by related experimental results.Remarkable accuracy improvement was acquired by the proposed NNS method compared with the unmodified CONWEP model.Moreover,huge efficiency superiority was obtained by the proposed NNS method compared with the CEL method.The proposed NNS method showed good accuracy when the scaled distance was greater than 0.2 m/kg^(1/3).It should be noted that there is no need to generate a new dataset again since the blast loads satisfy the similarity law,and the proposed NNS method can be directly used to simulate the blast loads generated by different cylindrical charges.The proposed NNS method with high efficiency and accuracy can be used as an effective method to analyze the dynamic response of structures under blast loads,and it has significant application prospects in designing protective structures.
基金support from the national projects(Grant No.:2011ZX05009-005and2010CB226703)
文摘A stuck drill string results in a major non-productive cost in extended reach drilling engineering. The first step is to determine the depth at which the sticking has occurred. Methods of measurement have been proved useful for determining the stuck points, but these operations take considerable time. As a result of the limitation with the current operational practices, calculation methods are still preferred to estimate the stuck point depth. Current analytical methods do not consider friction and are only valid for vertical rather than extended reach wells. The numerical method is established to take full account of down hole friction, tool joint, upset end of drill pipe, combination drill strings and tubular materials so that it is valid to determine the stuck point in extended reach wells. The pull test, torsion test and combined test of rotation and pulling can be used to determine the stuck point. The results show that down hole friction, tool joint, upset end of drill pipe, tubular sizes and materials have significant effects on the pull length and/or the twist angle of the stuck drill string.
文摘The purpose of this study was to investigate the effect of bolt profile on load transfer mechanism of fully grouted bolts in jointed rocks using analytical and numerical methods. Based on the analytical method with development of methods, a new model is presented. To validate the analytical model, five different profiles modeled by ANSYS software. The profile of rock bolts T3 and T4with load transfer capacity,respectively 180 and 195 kN in the jointed rocks was selected as the optimum profiles. Finally, the selected profiles were examined in Tabas Coal Mine. FLAC analysis indicates that patterns 6+7 with2 NO flexi bolt 4 m better than other patterns within the faulted zone.
基金Project supported by the National High Technology Research and Development Program of China (Grant No 2007AA12Z170)the Major Research Plan of the National Natural Science Foundation of China (Grant No 40706058)+1 种基金the Science-Technology Chenguang foundation for Young Scientist of Wuhan,China (Grant No 200850731388)the Canadian Space Agency Government Related Initiatives Program (GRIP) entitled Building Satellite Data into Fisheries and Oceans Operational Systems
文摘Although the nonlinear interactions between a single short gravity wave and a long wave can be solved analytically, the solution is less tractable in more general cases involving multiple short waves. In this work we present a numerical method of studying nonlinear interactions between a long wave and multiple short harmonic waves in infinitely deep water. Specifically, this method is applied to the calculation of the temporal and spatial evolutions of the surface elevations in which a given long wave interacts with several short harmonic waves. Another important application of our method is to quantitatively analyse the nonlinear interactions between an arbitrary short wave train and another short wave train. From simulation results, we obtain that the mechanism for the nonlinear interactions between one short wave train and another short wave train （expressed as wave train 2） leads to the energy focusing of the other short wave train （expressed as wave train 3）. This mechanism occurs on wave components with a narrow frequency bandwidth, whose frequencies are near that of wave train 3.
文摘An 8-channel HCN laser interferometer will be installed on HL-2A in near term. In order to get the spatial profile of the electron density Barr numerical method is adopted to realize the Abel inversion. In this article the result of the Abel inversion by Matlab GUI is given which can be updated to process the measured data of the 8-channel laser interferometer and provide the spatial distribution of the electron density.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11571366 and 11501570the Open Foundation of State Key Laboratory of High Performance Computing of China+1 种基金the Research Fund of National University of Defense Technology under Grant No JC15-02-02the Fund from HPCL
文摘We propose a high-order conservative method for the nonlinear Sehodinger/Gross-Pitaevskii equation with time- varying coefficients in modeling Bose Einstein condensation （BEC）. This scheme combined with the sixth-order compact finite difference method and the fourth-order average vector field method, finely describes the condensate wave function and physical characteristics in some small potential wells. Numerical experiments are presented to demonstrate that our numerical scheme is efficient by the comparison with the Fourier pseudo-spectral method. Moreover, it preserves several conservation laws well and even exactly under some specific conditions.
文摘A new provement of the existence and uniqueness about periodic boundary value Duffing equation is established by using global inverse function theorem. An algorithm for solving differential equation that has a large convergence domain is given. Finally, a numerical example is given.
文摘One of the critical aspects in mine design is slope stability analysis and the determination of stable slopes. In the Chador- Malu iron ore mine, one of the most important iron ore mines in central Iran, it was considered vital to perform a comprehensive slope stability analysis. At first, we divided the existing rock hosting pit into six zones and a geotechnical map was prepared. Then, the value of MRMR （Mining Rock Mass Rating） was determined for each zone. Owing to the fact that the Chador-Malu iron ore mine is located in a highly tectonic area and the rock mass completely crushed, the Hoek-Brown failure criterion was found suitable to estimate geo-mechanical parameters. After that, the value of cohesion （c） and friction angle （tp） were calculated for different geotechnical zones and relative graphs and equations were derived as a function of slope height. The stability analyses using numerical and limit equilibrium methods showed that some instability problems might occur by increasing the slope height. Therefore, stable slopes for each geotechnical zone and prepared sections were calculated and presented as a function of slope height.
基金Project supported by the National Natural Science Foundation of China (Grant Nos.52171251,U2106225,and 52231011)Dalian Science and Technology Innovation Fund (Grant No.2022JJ12GX036)。
文摘A numerical method is proposed to calculate the eigenvalues of the Zakharov–Shabat system based on Chebyshev polynomials. A mapping in the form of tanh(ax) is constructed according to the asymptotic of the potential function for the Zakharov–Shabat eigenvalue problem. The mapping can distribute Chebyshev nodes very well considering the gradient for the potential function. Using Chebyshev polynomials, tanh(ax) mapping, and Chebyshev nodes, the Zakharov–Shabat eigenvalue problem is transformed into a matrix eigenvalue problem. This method has good convergence for the Satsuma–Yajima potential and the convergence rate is faster than the Fourier collocation method. This method is not only suitable for simple potential functions but also converges quickly for a complex Y-shape potential. It can also be further extended to other linear eigenvalue problems.
基金Funded by the National Natural Science Foundation of China (No. 10272033) and Guangdong Provincial Natural Science Foundation(Nos.04105386,5300090 and 05001844).
文摘In this paper, by means of the maximum circle tensile stress on curve of constant ω and stress intensity factors by a path independent contour integral method, trajectories of maxed mode crack propagation are simulated through numerical manifold method. The crack propagation is traced dynamically by modifying the neighboring connection between the crack-top and nodes within elements in the calculating process. This method has the advantages such as less modified area, easiness of programming, high realizability and so on. Then a single sharp nicked specimen is used to verified the numerical result. It is shown that the provided method is reasonable and effective.
基金Supported by the National Natural Science Foundation of China under Grant Nos 60772135 and 10703004, and the CAST Innovation Foundation of China under Grant No 20080403.
文摘Based on the principle of equivalent phase comparison frequency, we propose a group-period phase comparison method. This method can be used to reveal the inherent relations between periodic signals and the change laws of the phase difference. If these laws are applied in the processing of the mutual relations between frequency signals, phase comparison can be accomplished without frequency normalization. Experimental results show that the method can enhance the measurement resolution to 10-13/s in the time domain.
基金Supported by the National Natural Science Foundation of China under Grant Nos 60772135 and 10703004, and the CAST Innovation Foundation of China under Grant No 20080403.
文摘Based on the principle of quantized delay-time, a super-high resolution time interval measurement method is proposed based on time-space relationships. Using the delay-time stability that time and frequency signal travel in a specific medium, the measured time interval can be quantized. Combined with the phase coincidence detection technique, the measurement of time can be changed into the measurement of space length. The resolution and the stability of the measurement system are easily improved. Experimental results show that the measurement resolution of the measured time interval depends on the length difference of the double delay-time unit. When the length difference is set up on millimeter level or sub-millimeter level, super-high measurement resolution from hundreds of picosecond to tens of picosecond can be obtained.
基金Project supported by the National Key Laboratory Foundation,China(Grant No.9140C530103110C5301)
文摘Based on the particle-in-cell technology and the secondary electron emission theory, a three-dimensional simulation method for multipactor is presented in this paper. By combining the finite difference time domain method and the panicle tracing method, such an algorithm is self-consistent and accurate since the interaction between electromagnetic fields and particles is properly modeled. In the time domain aspect, the generation of multipactor can be easily visualized, which makes it possible to gain a deeper insight into the physical mechanism of this effect. In addition to the classic secondary electron emission model, the measured practical secondary electron yield is used, which increases the accuracy of the algorithm. In order to validate the method, the impedance transformer and ridge waveguide filter are studied. By analyzing the evolution of the secondaries obtained by our method, multipactor thresholds of these components are estimated, which show good agreement with the experimental results. Furthermore, the most sensitive positions where multipactor occurs are determined from the phase focusing phenomenon, which is very meaningful for multipactor analysis and design.
基金funded by the National Key Research and Development Program of China (No. 2021YFB3401501)the Fundamental Research Funds for the Central Universities (No2022JCCXLJ01)。
文摘A plane mechanical model of rock breaking process by double disc cutter at the center of the cutterhead is established based on contact mechanics to analyze the stress evolution in the rock broken by cutters with different spacings. A continuous-discontinuous coupling numerical method based on zero-thickness cohesive elements is developed to simulate rock breaking using double cutters. The process, mechanism,and characteristics of rock breaking are comprehensively analyzed from five aspects: peak force, breaking form, breaking efficiency, crack mode, and breaking degree. The results show that under the penetrating action of cutters, dense cores are formed due to shear failure under respective cutters. The tensile cracks propagate in the rock, and then rock chips form with increasing penetration depth. When the cutter spacing is increased from 10 to 80 mm, the peak force gradually increases, the rock breaking range increases first and then decreases, the specific energy decreases first and then rises, and the breaking coefficient of intermediate rock decreases from 0.955 to 0.788. The area of rock breaking is positively correlated with the length of the tensile crack. Furthermore, the length of the tensile crack accounts for 14.4%–33.6% of the total crack length.
基金Supported by the National Natural Science Foundation of China under Grant Nos 60072004 and 60877057, and the National High-Tech Research and Development Program of China under Grant No 2007AA01Z270.
文摘An all-optical encryption-decryption method using an exclusive-or gate based on the cross-phase modulation between O-band and C-band light waves is proposed. The feasibility of the encryptionecryption technique is verified by handling binary signals at 2.5 Gbps, with less than 3dB penalty of extinction ratio and i dB polarization dependent loss.
基金Supported by the National Basic Research Program of China under Grant No 2007CB815000, and the National Natural Science Foundation of China under Grant No 10775004.
文摘The imaginary time step （ITS） method is applied to solve the Dirac equation with the nonlocal potential in coordinate space by the ITS evolution for the corresponding Schrfdinger-like equation for the upper component. It is demonstrated that the ITS evolution can be equivalently performed for the Schrodinger-like equation with or without localization. The latter algorithm is recommended in the application for the reason of simplicity and efficiency. The feasibility and reliability of this algorithm are also illustrated by taking the nucleus ^16O as an example, where the same results as the shooting method for the Dirae equation with localized effective potentials are obtained.
文摘The finite volume method has been successfully applied in several engineering fields and has shown outstanding performance in fluid dynamics simulation. In this paper, the general framework for the simulation ofnear-wellbore systems using the finite volume method is described. The mathematical model and the numerical model developed by the authors are presented and discussed. A radial geometry in the vertical plane was implemented so as to thoroughly describe near-wellbore phenomena. The model was then used to simulate injection tests in an oil reservoir through a horizontal well and proved very powerful to correctly reproduce the transient pressure behavior. The reason for this is the robustness of the method, which is independent of the gridding options because the discretization is performed in the physical space. The model is able to describe the phenomena taking place in the reservoir even in complex situations, i.e. in the presence of heterogeneities and permeability barriers, demonstrating the flexibility of the finite volume method when simulating non-conventional tests. The results are presented in comparison with those obtained with the finite difference numerical approach and with analytical methods, if possible.
基金Project supported by the National Natural Science Foundation of China (Grant No 50575037)the Doctoral Foundation of Dalian University of China (Grant No SBQ200810)
文摘This paper studies numerically the thermo-mechanical effects of ZrO2 thermal barrier coatings （TBCs） irradiated by a high-intensity pulsed ion beam in consideration of the surface structure. Taking the deposited energy of ion beams in TBCs as the source term in the thermal conduction equation, the distribution of temperature in TBCs was simulated. Then, based on the distribution, the evolution of thermal stress was calculated by the finite element method. The results show that tensile radial stress formed at the valley of TBC surfaces after irradiation by HIPIB. Therefore, if cracks happen, they must be at valleys instead of peaks. As for the stress waves, no matter whether through peak or valley position, tensile and compressive stresses are present alternately inside TBCs along the depth direction, and the strength of stress decreases with time.
文摘The transient thermoelastic stress fields of GaN films is analyzed by the finite element method for the laser lift-off （LLO） technique. Stress distributions in GaN films irradiated by pulse laser with different energy densities as functions of time and depth are simulated. The results show that the high thermoelastic stress distributions in GaN films localize within about 1 μm below the GaN/Al2O3 interface using proper laser parameters. It is also found that GaN films can avoid the thermal deformation because the maximum thermoelastic stress 4.28 GPa is much smaller than the yield strength of GaN 15GPa. The effects of laser beam dimension and the thickness of GaN films on stress distribution are also analyzed. The variation range of laser beam dimension as a function of the thickness of GaN films is simulated to keep the GaN films free of thermal deformation. LLO experiments are also carried out. GaN-based light-emitting diodes （LEDs） are separated from sapphire substrates using the parameters obtained from the simulation. Compared with devices before LLO, P-I-V measurements of GaN- based LEDs after LLO show that the electrical and optical characteristics improve greatly, indicating that no stress damage is brought to GaN films using proper parameters obtained by calculation during LLO.
文摘We investigate the self-heating effect of mid-infrared quantum cascade lasers by using a direct-based pulse injecting current and spectroscopy method. Based on the characterization system, the thermal characteristics of gas source MBE grown 8.4μm InP-based GalnAs/AIInAs DFB-QCLs are evaluated. The method and characterization system are also useful in evaluating the thermal characteristics of other types of mid-infrared diode lasers.
