In order to gain a deeper understanding of the effect of pulsed current on the mechanical properties and size effect of nanocrystalline Ni foils,nanocrystalline Ni foils with different grain thickness-to-grain size ra...In order to gain a deeper understanding of the effect of pulsed current on the mechanical properties and size effect of nanocrystalline Ni foils,nanocrystalline Ni foils with different grain thickness-to-grain size ratios(λ)were prepared using pulsed electrodeposition in this paper and unidirectional tensile experiments were carried out at room temperature with different currents and their applied directions.The experimental results show that the nanocrystalline Ni foil produces an obvious electroplasticity effect after applying the current field,and when 300<λ<1100,the current weakens the size effect of nanocrystalline Ni foils to a certain extent,and the angle between the current direction and the deformation direction also affects the mechanical response of nanocrystalline Ni foils,and when the angle between the current direction and the deformation direction is 0°,electroplasticity effect is the best,and the current has the most significant effect of abating the size effect of the material.The mechanism of unidirectional tensile deformation of nanocrystalline Ni foils under the effect of pulsed current was analyzed using TEM and TKD.It was found that the applied pulse current increased the activity of the nanocrystalline boundaries,promoted the movement of dislocations,and reduced the tendency of dislocation entanglement.The higher the peak current density and the smaller the angle between the direction of the current and the direction of deformation,the smaller the grain boundary orientation difference,the more dispersed the grain orientation,and the lower the density of geometrically necessary dislocations(GND)in the deformed nanocrystalline foil,the more significant the effect on material plasticity improvement.展开更多
To understand the high strain rate deformation mechanism and determine the grain size,strain rate and porosity dependent yield strength of nanocrystalline materials,a new mechanical model based on the deformation mech...To understand the high strain rate deformation mechanism and determine the grain size,strain rate and porosity dependent yield strength of nanocrystalline materials,a new mechanical model based on the deformation mechanism of nanocrystalline materials under high strain rate loading was developed.As a first step of the research,the yield behavior of the nanocrystalline materials under high strain rate loading was mainly concerned in the model and uniform deformation was assumed for simplification.Nanocrystalline materials were treated as composites consisting of grain interior phase and grain boundary phase,and grain interior and grain boundary deformation mechanisms under high strain rate loading were analyzed,then Voigt model was applied to coupling grain boundary constitutive relation with mechanical model for grain interior phase to describe the overall yield mechanical behavior of nanocrystalline materials.The predictions by the developed model on the yield strength of nanocrysatlline materials at high strain rates show good agreements with various experimental data.Further discussion was presented for calculation results and relative experimental observations.展开更多
To completely understand the rate-dependent stress-strain behavior of the porous nanocrystalline materials,it is necessary to formulate a constitutive model that can reflect the complicated experimentally observed str...To completely understand the rate-dependent stress-strain behavior of the porous nanocrystalline materials,it is necessary to formulate a constitutive model that can reflect the complicated experimentally observed stress-strain relations of nanocrystalline materials.The nanocrystalline materials consisting grain interior and grain boundary are considered as viscoplastic and porous materials for the reasons that their mechanical deformation is commonly governed by both dislocation glide and diffusion,and pores commonly exist in the nanocrystalline materials.A constitutive law of the unified theory reflecting the stress-strain relations was established and verified by experimental data of bulk nanocrystalline Ni prepared by hydrogen direct current arc plasma evaporation method and hot compression.The effect of the evolution of porosity on stress-strain relations was taken into account to make that the predicted results can keep good agreements with the corresponding experimental results.展开更多
Nanocrystalline diamond films were deposited on Co-cemented carbide substrates using acetone/ H<sub>2</sub>/Ar gas mixture by bias-enhanced hot filament chemical vapor deposition（HFCVD） technique.The evi...Nanocrystalline diamond films were deposited on Co-cemented carbide substrates using acetone/ H<sub>2</sub>/Ar gas mixture by bias-enhanced hot filament chemical vapor deposition（HFCVD） technique.The evidence of nanocrystallinity,smoothness and purity was obtained by characterizing the sample with scanning electron microscopy（SEM）,X-ray diffraction（XRD）,Raman spectroscopy,atomic force microscopy （AFM ）,and field emission transmission electron microscopy（FE-TEM ）.The results show that nanocrystalline diamond films consists of nanocrystalline diamond grains with sizes range from 20 to 80 nm and contain a large amount of grain boundaries.The surface roughness of the films is measured as R<sub>a</sub>【50nm.The Raman spectroscopy,XRD pattern,and FE-TEM image of the films indicate the presence of nanocrystalline diamond.A new process is used to deposit composite diamond coatings by a two-step chemical vapor deposition procedure,including first the deposition of the rough polycrystalline diamond and then the smooth fine-grained nanocrystalline diamond film.Such composite diamond coatings not only display good adhesion and wear resistant properties,but also have smooth surfaces that are liable to polishing.This coating technology can not only meet the requirement of the adhesion of diamond coatings,but also reduce surface roughness of diamond coatings effectively,thus remove the obstacles for the industrialization of CVD diamond coatings.The diamondcoated dies with these composite coatings show obvious effect in the practical application.展开更多
Nanocrystalline and amorphous Mg-Nd-Ni-Cu quaternary alloys with a composition of(Mg_(24)Ni_(10)Cu_2)_(100-x)Nd_x(x=0, 5, 10, 15, 20) were prepared by melt spinning technology and their structures as well as gaseous h...Nanocrystalline and amorphous Mg-Nd-Ni-Cu quaternary alloys with a composition of(Mg_(24)Ni_(10)Cu_2)_(100-x)Nd_x(x=0, 5, 10, 15, 20) were prepared by melt spinning technology and their structures as well as gaseous hydrogen storage characteristics were investigated. The XRD, TEM and SEM linked with EDS detections reveal that the as-spun Nd-free alloy holds an entire nanocrystalline structure but a nanocrystalline and amorphous structure for the as-spun Nd-added alloy, implying that the addition of Nd facilitates the glass forming in the Mg_2Ni-type alloy. Furthermore, the degree of amorphization of the as-spun Nd-added alloy and thermal stability of the amorphous structure clearly increase with the spinning rate rising. The melt spinning ameliorates the hydriding and dehydriding kinetics of the alloys dramatically. Specially, the rising of the spinning rate from 0(the as-cast was defined as the spinning rate of 0 m/s) to 40 m/s brings on the hydrogen absorption saturation ratio(R_5~a)(a ratio of the hydrogen absorption quantity in 5 min to the saturated hydrogen absorption capacity) increasing from 36.9% to 91.5% and the hydrogen desorption ratio(R_(1 0)~d)(a ratio of the hydrogen desorption quantity in 10 min to the saturated hydrogen absorption capacity) rising from 16.4% to 47.7% for the(x=10) alloy, respectively.展开更多
The structural evolution and stability of Fe100-xNix（x= 10, 20, 35, 50） alloys prepared by mechanical alloying were investigated through X-ray diffraction analysis and transmission electron microscopy. The intrinsic...The structural evolution and stability of Fe100-xNix（x= 10, 20, 35, 50） alloys prepared by mechanical alloying were investigated through X-ray diffraction analysis and transmission electron microscopy. The intrinsic conditions of preparation determining phase stability in nanocrystalline were clarified. After being milled for 120 h, the powders of Fego Ni10 and Fe80 Ni20 consist of a single α（bcc） phase, Fe30 Ni30 powders are a single γ（fcc）, and for Fe65 Ni35 powders there is co-existence of α and γ phases. The as-milled Fe80 Ni20 powders annealed at 680℃ exhibits the stability of high-temperature γ phase at room temperature, which is consistent with the theoretical prediction.展开更多
The nanosystem has received considerable attention because of its peculiar pheno mena,which is different from macroscopy and microscopy. At present,the upsurge o f researching nanomaterials has shifted from nano parti...The nanosystem has received considerable attention because of its peculiar pheno mena,which is different from macroscopy and microscopy. At present,the upsurge o f researching nanomaterials has shifted from nano particles to one dimensional na nosystem,such as nanowires,nanotubes,and so on.Seen from literatures, the repor ts on carbon nanotubes wer e more,on nanowires were less,and on transition metallic salt nanowires were noth ing .In this paper,AgCl nanocrystalline wires were successfully synthesized by Rever s e Micelle soft Templates, which will open a new way for the synthesis and applic ation of one dimensional nanomaterials.展开更多
Wurtzite structure gallium nitride GaN,a direct bandgap semiconductor,is an ideal material for fabrication of blue/green light emitting diodes,laser diodes, and high powder Integrated Circuites.Up to now,small single ...Wurtzite structure gallium nitride GaN,a direct bandgap semiconductor,is an ideal material for fabrication of blue/green light emitting diodes,laser diodes, and high powder Integrated Circuites.Up to now,small single crystals,powders and nanomaterials of GaN have successfully synthesized as well as applied films gro wn by MOCVD.In this report,another condensed state of GaN,nanocrystal assembled bulk,was synthesized and its spectra are investigated. Metal gallium or gallium alloys are used as starting materials and haloids used as catalyzer in ammonia.Buff transparent GaN bulks were obtained at 350—500℃.P owder X ray diffraction indicated that the bulks are wurtaite GaN single phase. HRTEM confirmed that the bulks are composed of nanoparticles with average size o f 12mm.The well crystallized particle shows clear diffraction spots.PL spectra of the material are similar to that of GaN singe crystals under the ultraviolet excitation,but blue shift is observed near gap band.Red shift occurs in Raman scattering comparing with single crystals.The materials have the broad potential in the future because it not only possesses of mechanical and optical characteri stics owned by single crystals but also holds the nano properties of the nanoma terials.展开更多
In this work,a comprehensive comparison regarding the impacts of M(M=Cu,Co,Mn)substitution for Ni on the structures and the hydrogen storage kinetics of the nanocrystalline and amorphous Mg20Ni10-xMx(M=Cu,Co,Mn; x=0-4...In this work,a comprehensive comparison regarding the impacts of M(M=Cu,Co,Mn)substitution for Ni on the structures and the hydrogen storage kinetics of the nanocrystalline and amorphous Mg20Ni10-xMx(M=Cu,Co,Mn; x=0-4)alloys prepared by melt spinning has been carried out.The analysis of XRD and TEM reveals that the as-spun(M=None,Cu)alloys display an entire nanocrystalline structure,whereas the as-spun(M=Co,Mn)alloys hold a mixed structure of nanocrystalline and amorphous structure when M content x=4,indicating that the substitution of M(M=Co,Mn)for Ni facilitates the glass formation in the Mg2Ni-type alloy.Besides,all the as-spun alloys have a major phase of Mg2Ni but M(M=Co,Mn)substitution brings on the formation of some secondary phases,MgCo2 and Mg phases for M=Co as well as MnNi and Mg phases for M=Mn.Based upon the measurements of the automatic Sieverts apparatus and the automatic galvanostatic system,the impacts engendered by M(M=Cu,Co,Mn)substitution on the gaseous and electrochemical hydrogen storage kinetics of the alloys appear to be evident.The gaseous hydriding kinetics of the alloys first rises and then declines with the growing of M(M=Cu,Co,Mn)content.Particularly,the M(M= Mn)substitution results in a sharp drop in the hydriding kinetics when x=4.The M(M=Cu,Co,Mn)substitution ameliorates the dehydriding kinetics dramatically in the order(M=Co)>(M=Mn)>(M=Cu).The electrochemical kinetics of the alloys visibly grows with M content rising for(M=Cu,Co),while it first increases and then declines for(M=Mn).展开更多
The photoluminescence of the transparent GaN nanocrystalline solids is studied.T hree new intensive isolated narrow red emission bands (centered at 2.08eV,2.01eV ,1.99eV) and one broad blue band (centered at 2.7eV) ar...The photoluminescence of the transparent GaN nanocrystalline solids is studied.T hree new intensive isolated narrow red emission bands (centered at 2.08eV,2.01eV ,1.99eV) and one broad blue band (centered at 2.7eV) are observed.Phonon structu re on the low energy side of the blue band is observed.A mechanism to explain th e origin of these bands is proposed.The three red bands may originate from the t ransitions of deep donor levels to shallow acceptors,while the blue band may fro m the transitions of shallow donors to deep levels with ground and excited state s.The unique property of red emission from the GaN nanocrystalline solids is att ributed to the interaction among the composed nano sized particles which may le d to the generation of high concentration of defects.展开更多
The crystallization kinetics of amorphous (Nd3.6Pr5.4Fe83Co3B5) and the preparation of α-Fe/Nd2Fe14B nanocomposite magnets by controlled melt-solidification of (Nd3.6Pr5.4Fe83Co3B5) was investigated by employing DTA,...The crystallization kinetics of amorphous (Nd3.6Pr5.4Fe83Co3B5) and the preparation of α-Fe/Nd2Fe14B nanocomposite magnets by controlled melt-solidification of (Nd3.6Pr5.4Fe83Co3B5) was investigated by employing DTA, XRD, and TEM. The results show that a metastable intermediate phase (Nd8Fe27B24) prior to α-Fe and Nd2Fe14B phases is crystallized as the amorphous Nd3.6Pr5.4Fe83Co3B5 is heated to 1 223 K. The crystallization activation energy of α-Fe and Nd8Fe27B24 phases is larger at the beginning stage of crystallization, and then it decreases with crystallized fraction x for the former and has little change when x is below 70% for the latter, which essentially results in an α-Fe/Nd2Fe14B microstructure with a relatively coarse grain size about 20-60 nm and a non-uniform distribution of grain size in the annealed alloy. The α-Fe/Nd2Fe14B nanocomposite magnets with a small average grain size about 14 nm and a quite uniform grain size distribution were prepared by controlled melt-solidification of (Nd3.6Pr5.4Fe83Co3B5) at a wheel speed of 20 m·s-1 during melt-spinning. The magnets show a high maximum energy product of （BH）max = 194 kJ·m-3, which is nearly twice of that of the nanocomposite magnets made by annealing the amorphous Nd3.6Pr5.4Fe83Co3B5 precursor alloy.展开更多
基金Project(51975167)supported by the National Natural Science Foundation of China。
文摘In order to gain a deeper understanding of the effect of pulsed current on the mechanical properties and size effect of nanocrystalline Ni foils,nanocrystalline Ni foils with different grain thickness-to-grain size ratios(λ)were prepared using pulsed electrodeposition in this paper and unidirectional tensile experiments were carried out at room temperature with different currents and their applied directions.The experimental results show that the nanocrystalline Ni foil produces an obvious electroplasticity effect after applying the current field,and when 300<λ<1100,the current weakens the size effect of nanocrystalline Ni foils to a certain extent,and the angle between the current direction and the deformation direction also affects the mechanical response of nanocrystalline Ni foils,and when the angle between the current direction and the deformation direction is 0°,electroplasticity effect is the best,and the current has the most significant effect of abating the size effect of the material.The mechanism of unidirectional tensile deformation of nanocrystalline Ni foils under the effect of pulsed current was analyzed using TEM and TKD.It was found that the applied pulse current increased the activity of the nanocrystalline boundaries,promoted the movement of dislocations,and reduced the tendency of dislocation entanglement.The higher the peak current density and the smaller the angle between the direction of the current and the direction of deformation,the smaller the grain boundary orientation difference,the more dispersed the grain orientation,and the lower the density of geometrically necessary dislocations(GND)in the deformed nanocrystalline foil,the more significant the effect on material plasticity improvement.
基金Project(10502025) supported by the National Natural Science Foundation of ChinaProject(101005) supported by Fok Ying Tong Education FoundationProject(BK2007528) supported by the Natural Science Foundation of Jiangsu Province,China
文摘To understand the high strain rate deformation mechanism and determine the grain size,strain rate and porosity dependent yield strength of nanocrystalline materials,a new mechanical model based on the deformation mechanism of nanocrystalline materials under high strain rate loading was developed.As a first step of the research,the yield behavior of the nanocrystalline materials under high strain rate loading was mainly concerned in the model and uniform deformation was assumed for simplification.Nanocrystalline materials were treated as composites consisting of grain interior phase and grain boundary phase,and grain interior and grain boundary deformation mechanisms under high strain rate loading were analyzed,then Voigt model was applied to coupling grain boundary constitutive relation with mechanical model for grain interior phase to describe the overall yield mechanical behavior of nanocrystalline materials.The predictions by the developed model on the yield strength of nanocrysatlline materials at high strain rates show good agreements with various experimental data.Further discussion was presented for calculation results and relative experimental observations.
基金Project(10502025) supported by the National Natural Science Foundation of ChinaProject(101005) supported by the Fok Ying Tong Education FoundationProject(BK2007528) supported by the Natural Science Foundation of Jiangsu Province,China
文摘To completely understand the rate-dependent stress-strain behavior of the porous nanocrystalline materials,it is necessary to formulate a constitutive model that can reflect the complicated experimentally observed stress-strain relations of nanocrystalline materials.The nanocrystalline materials consisting grain interior and grain boundary are considered as viscoplastic and porous materials for the reasons that their mechanical deformation is commonly governed by both dislocation glide and diffusion,and pores commonly exist in the nanocrystalline materials.A constitutive law of the unified theory reflecting the stress-strain relations was established and verified by experimental data of bulk nanocrystalline Ni prepared by hydrogen direct current arc plasma evaporation method and hot compression.The effect of the evolution of porosity on stress-strain relations was taken into account to make that the predicted results can keep good agreements with the corresponding experimental results.
基金Supported by the National Natural Science Foundation of China(50575135)
文摘Nanocrystalline diamond films were deposited on Co-cemented carbide substrates using acetone/ H<sub>2</sub>/Ar gas mixture by bias-enhanced hot filament chemical vapor deposition（HFCVD） technique.The evidence of nanocrystallinity,smoothness and purity was obtained by characterizing the sample with scanning electron microscopy（SEM）,X-ray diffraction（XRD）,Raman spectroscopy,atomic force microscopy （AFM ）,and field emission transmission electron microscopy（FE-TEM ）.The results show that nanocrystalline diamond films consists of nanocrystalline diamond grains with sizes range from 20 to 80 nm and contain a large amount of grain boundaries.The surface roughness of the films is measured as R<sub>a</sub>【50nm.The Raman spectroscopy,XRD pattern,and FE-TEM image of the films indicate the presence of nanocrystalline diamond.A new process is used to deposit composite diamond coatings by a two-step chemical vapor deposition procedure,including first the deposition of the rough polycrystalline diamond and then the smooth fine-grained nanocrystalline diamond film.Such composite diamond coatings not only display good adhesion and wear resistant properties,but also have smooth surfaces that are liable to polishing.This coating technology can not only meet the requirement of the adhesion of diamond coatings,but also reduce surface roughness of diamond coatings effectively,thus remove the obstacles for the industrialization of CVD diamond coatings.The diamondcoated dies with these composite coatings show obvious effect in the practical application.
基金Projects(51161015,51371094)supported by the National Natural Science Foundation of China
文摘Nanocrystalline and amorphous Mg-Nd-Ni-Cu quaternary alloys with a composition of(Mg_(24)Ni_(10)Cu_2)_(100-x)Nd_x(x=0, 5, 10, 15, 20) were prepared by melt spinning technology and their structures as well as gaseous hydrogen storage characteristics were investigated. The XRD, TEM and SEM linked with EDS detections reveal that the as-spun Nd-free alloy holds an entire nanocrystalline structure but a nanocrystalline and amorphous structure for the as-spun Nd-added alloy, implying that the addition of Nd facilitates the glass forming in the Mg_2Ni-type alloy. Furthermore, the degree of amorphization of the as-spun Nd-added alloy and thermal stability of the amorphous structure clearly increase with the spinning rate rising. The melt spinning ameliorates the hydriding and dehydriding kinetics of the alloys dramatically. Specially, the rising of the spinning rate from 0(the as-cast was defined as the spinning rate of 0 m/s) to 40 m/s brings on the hydrogen absorption saturation ratio(R_5~a)(a ratio of the hydrogen absorption quantity in 5 min to the saturated hydrogen absorption capacity) increasing from 36.9% to 91.5% and the hydrogen desorption ratio(R_(1 0)~d)(a ratio of the hydrogen desorption quantity in 10 min to the saturated hydrogen absorption capacity) rising from 16.4% to 47.7% for the(x=10) alloy, respectively.
文摘The structural evolution and stability of Fe100-xNix（x= 10, 20, 35, 50） alloys prepared by mechanical alloying were investigated through X-ray diffraction analysis and transmission electron microscopy. The intrinsic conditions of preparation determining phase stability in nanocrystalline were clarified. After being milled for 120 h, the powders of Fego Ni10 and Fe80 Ni20 consist of a single α（bcc） phase, Fe30 Ni30 powders are a single γ（fcc）, and for Fe65 Ni35 powders there is co-existence of α and γ phases. The as-milled Fe80 Ni20 powders annealed at 680℃ exhibits the stability of high-temperature γ phase at room temperature, which is consistent with the theoretical prediction.
文摘The nanosystem has received considerable attention because of its peculiar pheno mena,which is different from macroscopy and microscopy. At present,the upsurge o f researching nanomaterials has shifted from nano particles to one dimensional na nosystem,such as nanowires,nanotubes,and so on.Seen from literatures, the repor ts on carbon nanotubes wer e more,on nanowires were less,and on transition metallic salt nanowires were noth ing .In this paper,AgCl nanocrystalline wires were successfully synthesized by Rever s e Micelle soft Templates, which will open a new way for the synthesis and applic ation of one dimensional nanomaterials.
基金Supported by National Natural Science Foundation of China(50271047)The Natural Science Foundation ofTianjin,as well as the"985"Program Foundation of Tianjin University(003601811)
文摘Wurtzite structure gallium nitride GaN,a direct bandgap semiconductor,is an ideal material for fabrication of blue/green light emitting diodes,laser diodes, and high powder Integrated Circuites.Up to now,small single crystals,powders and nanomaterials of GaN have successfully synthesized as well as applied films gro wn by MOCVD.In this report,another condensed state of GaN,nanocrystal assembled bulk,was synthesized and its spectra are investigated. Metal gallium or gallium alloys are used as starting materials and haloids used as catalyzer in ammonia.Buff transparent GaN bulks were obtained at 350—500℃.P owder X ray diffraction indicated that the bulks are wurtaite GaN single phase. HRTEM confirmed that the bulks are composed of nanoparticles with average size o f 12mm.The well crystallized particle shows clear diffraction spots.PL spectra of the material are similar to that of GaN singe crystals under the ultraviolet excitation,but blue shift is observed near gap band.Red shift occurs in Raman scattering comparing with single crystals.The materials have the broad potential in the future because it not only possesses of mechanical and optical characteri stics owned by single crystals but also holds the nano properties of the nanoma terials.
基金Projects(51161015,51371094)supported by National Natural Science Foundations of ChinaProject(2011ZD10)supported by Natural Science Foundation of Inner Mongolia,China
文摘In this work,a comprehensive comparison regarding the impacts of M(M=Cu,Co,Mn)substitution for Ni on the structures and the hydrogen storage kinetics of the nanocrystalline and amorphous Mg20Ni10-xMx(M=Cu,Co,Mn; x=0-4)alloys prepared by melt spinning has been carried out.The analysis of XRD and TEM reveals that the as-spun(M=None,Cu)alloys display an entire nanocrystalline structure,whereas the as-spun(M=Co,Mn)alloys hold a mixed structure of nanocrystalline and amorphous structure when M content x=4,indicating that the substitution of M(M=Co,Mn)for Ni facilitates the glass formation in the Mg2Ni-type alloy.Besides,all the as-spun alloys have a major phase of Mg2Ni but M(M=Co,Mn)substitution brings on the formation of some secondary phases,MgCo2 and Mg phases for M=Co as well as MnNi and Mg phases for M=Mn.Based upon the measurements of the automatic Sieverts apparatus and the automatic galvanostatic system,the impacts engendered by M(M=Cu,Co,Mn)substitution on the gaseous and electrochemical hydrogen storage kinetics of the alloys appear to be evident.The gaseous hydriding kinetics of the alloys first rises and then declines with the growing of M(M=Cu,Co,Mn)content.Particularly,the M(M= Mn)substitution results in a sharp drop in the hydriding kinetics when x=4.The M(M=Cu,Co,Mn)substitution ameliorates the dehydriding kinetics dramatically in the order(M=Co)>(M=Mn)>(M=Cu).The electrochemical kinetics of the alloys visibly grows with M content rising for(M=Cu,Co),while it first increases and then declines for(M=Mn).
文摘The photoluminescence of the transparent GaN nanocrystalline solids is studied.T hree new intensive isolated narrow red emission bands (centered at 2.08eV,2.01eV ,1.99eV) and one broad blue band (centered at 2.7eV) are observed.Phonon structu re on the low energy side of the blue band is observed.A mechanism to explain th e origin of these bands is proposed.The three red bands may originate from the t ransitions of deep donor levels to shallow acceptors,while the blue band may fro m the transitions of shallow donors to deep levels with ground and excited state s.The unique property of red emission from the GaN nanocrystalline solids is att ributed to the interaction among the composed nano sized particles which may le d to the generation of high concentration of defects.
文摘The crystallization kinetics of amorphous (Nd3.6Pr5.4Fe83Co3B5) and the preparation of α-Fe/Nd2Fe14B nanocomposite magnets by controlled melt-solidification of (Nd3.6Pr5.4Fe83Co3B5) was investigated by employing DTA, XRD, and TEM. The results show that a metastable intermediate phase (Nd8Fe27B24) prior to α-Fe and Nd2Fe14B phases is crystallized as the amorphous Nd3.6Pr5.4Fe83Co3B5 is heated to 1 223 K. The crystallization activation energy of α-Fe and Nd8Fe27B24 phases is larger at the beginning stage of crystallization, and then it decreases with crystallized fraction x for the former and has little change when x is below 70% for the latter, which essentially results in an α-Fe/Nd2Fe14B microstructure with a relatively coarse grain size about 20-60 nm and a non-uniform distribution of grain size in the annealed alloy. The α-Fe/Nd2Fe14B nanocomposite magnets with a small average grain size about 14 nm and a quite uniform grain size distribution were prepared by controlled melt-solidification of (Nd3.6Pr5.4Fe83Co3B5) at a wheel speed of 20 m·s-1 during melt-spinning. The magnets show a high maximum energy product of （BH）max = 194 kJ·m-3, which is nearly twice of that of the nanocomposite magnets made by annealing the amorphous Nd3.6Pr5.4Fe83Co3B5 precursor alloy.
