The longitudinal dispersion of the projectile in shooting tests of two-dimensional trajectory corrections fused with fixed canards is extremely large that it sometimes exceeds the correction ability of the correction ...The longitudinal dispersion of the projectile in shooting tests of two-dimensional trajectory corrections fused with fixed canards is extremely large that it sometimes exceeds the correction ability of the correction fuse actuator.The impact point easily deviates from the target,and thus the correction result cannot be readily evaluated.However,the cost of shooting tests is considerably high to conduct many tests for data collection.To address this issue,this study proposes an aiming method for shooting tests based on small sample size.The proposed method uses the Bootstrap method to expand the test data;repeatedly iterates and corrects the position of the simulated theoretical impact points through an improved compatibility test method;and dynamically adjusts the weight of the prior distribution of simulation results based on Kullback-Leibler divergence,which to some extent avoids the real data being"submerged"by the simulation data and achieves the fusion Bayesian estimation of the dispersion center.The experimental results show that when the simulation accuracy is sufficiently high,the proposed method yields a smaller mean-square deviation in estimating the dispersion center and higher shooting accuracy than those of the three comparison methods,which is more conducive to reflecting the effect of the control algorithm and facilitating test personnel to iterate their proposed structures and algorithms.;in addition,this study provides a knowledge base for further comprehensive studies in the future.展开更多
The detection of hypersonic targets usually confronts range migration(RM)issue before coherent integration(CI).The traditional methods aiming at correcting RM to obtain CI mainly considers the narrow-band radar condit...The detection of hypersonic targets usually confronts range migration(RM)issue before coherent integration(CI).The traditional methods aiming at correcting RM to obtain CI mainly considers the narrow-band radar condition.However,with the increasing requirement of far-range detection,the time bandwidth product,which is corresponding to radar’s mean power,should be promoted in actual application.Thus,the echo signal generates the scale effect(SE)at large time bandwidth product situation,influencing the intra and inter pulse integration performance.To eliminate SE and correct RM,this paper proposes an effective algorithm,i.e.,scaled location rotation transform(ScLRT).The ScLRT can remove SE to obtain the matching pulse compression(PC)as well as correct RM to complete CI via the location rotation transform,being implemented by seeking the actual rotation angle.Compared to the traditional coherent detection algorithms,Sc LRT can address the SE problem to achieve better detection/estimation capabilities.At last,this paper gives several simulations to assess the viability of ScLRT.展开更多
Magnetic field gradient tensor measurement is an important technique to obtain position information of magnetic objects. When using magnetic field sensors to measure magnetic field gradient as the coefficients of tens...Magnetic field gradient tensor measurement is an important technique to obtain position information of magnetic objects. When using magnetic field sensors to measure magnetic field gradient as the coefficients of tensor, field differentiation is generally approximated by field difference. As a result, magnetic objects positioning by magnetic field gradient tensor measurement always involves an inherent error caused by sensor sizes, leading to a reduction in detectable distance and detectable angle. In this paper, the inherent positioning error caused by magnetic field gradient tensor measurement is calculated and corrected by iterations based on the systematic position error distribution patterns. The results show that, the detectable distance range and the angle range of an ac magnetic object（2.44 Am^2@1 kHz） can be increased from（0.45 m, 0.75 m）,（0？, 25？） to（0.30 m, 0.80 m）,（0？,80？）, respectively.展开更多
Compared with the one-dimensional trajectory correction technology which adjusts longitudinal range, not only does the two-dimensional trajectory correction technology adjust the force in velocity direction, but also ...Compared with the one-dimensional trajectory correction technology which adjusts longitudinal range, not only does the two-dimensional trajectory correction technology adjust the force in velocity direction, but also need to modulate the lateral force or trajectory (perpendicular to the vertical plane of fire direction). Therefore, the structure of control cabin of two-dimensional trajectory correction projectile (TDTCP) is more complicated than that of one-dimensional trajectory correction projectile (ODTCP). To simplify the structure of control cabin of TDTCP and reduce the cost, a scheme of adding a damping disk to the control cabin of ODTCP has been developed recently. The damping disk is unfolded at the right moment during its flight to change the ballistic drift of spin stabilized projectile. For this technical scheme of TDTCP, a fast and accurate impact point prediction method based on extended Kalman filter is presented. An approximate formula for predicting the ballistic drift and trajectory correction quantity is deduced. And the lateral correction capability for different fire angles and its influencing factors are analyzed. All the work is valuable for further research.展开更多
A target localization algorithm,which uses the measurement information from onboard GPS and onboard laser detector to acquire the target position,is proposed to obtain the accurate position of ground target in real ti...A target localization algorithm,which uses the measurement information from onboard GPS and onboard laser detector to acquire the target position,is proposed to obtain the accurate position of ground target in real time in the trajectory correction process of semi-active laser terminal correction projectile.A target localization model is established according to projectile position,attitude and line-of-sight angle.The effects of measurement errors of projectile position,attitude and line-of-sight angle on localization accuracy at different quadrant elevation angles are analyzed through Monte-Carlo simulation.The simulation results show that the measurement error of line-of-sight angle has the largest influence on the localization accuracy.The localization accuracy decreases with the increase in quadrant elevation angle.However,the maximum localization accuracy is less than 7 m.The proposed algorithm meets the accuracy and real-time requirements of target localization.展开更多
The algorithm of dense spectrum correction has been raised and proved based on the correction of discrete spectrum by fast Fourier transform.The result of simulation shows that such algorithm has advantages of high ac...The algorithm of dense spectrum correction has been raised and proved based on the correction of discrete spectrum by fast Fourier transform.The result of simulation shows that such algorithm has advantages of high accuracy and small amount of calculation.The algorithm has been successfully applied to the analysis of vibration signals from internal combustion engine.To calculate discrete spectrum,fast Fourier transform has been used to calculate the discrete spectrum by the signals acquired by the sensors on the oil pan,and the signal has been extracted from the mixed signals.展开更多
This work investigates the performance of various forward error correction codes, by which the MIMO-OFDM system is deployed. To ensure fair investigation, the performance of four modulations, namely, binary phase shif...This work investigates the performance of various forward error correction codes, by which the MIMO-OFDM system is deployed. To ensure fair investigation, the performance of four modulations, namely, binary phase shift keying(BPSK), quadrature phase shift keying(QPSK), quadrature amplitude modulation(QAM)-16 and QAM-64 with four error correction codes(convolutional code(CC), Reed-Solomon code(RSC)+CC, low density parity check(LDPC)+CC, Turbo+CC) is studied under three channel models(additive white Guassian noise(AWGN), Rayleigh, Rician) and three different antenna configurations(2×2, 2×4, 4×4). The bit error rate(BER) and the peak signal to noise ratio(PSNR) are taken as the measures of performance. The binary data and the color image data are transmitted and the graphs are plotted for various modulations with different channels and error correction codes. Analysis on the performance measures confirm that the Turbo + CC code in 4×4 configurations exhibits better performance.展开更多
The two-dimensional trajectory correction needs to adjust not only the force in velocity direction,but also the lateral force or lateral trajectory (normal to the perpendicular plane of fire direction) . Therefore,its...The two-dimensional trajectory correction needs to adjust not only the force in velocity direction,but also the lateral force or lateral trajectory (normal to the perpendicular plane of fire direction) . Therefore,its structure of control cabin is more complicated than that of one-dimensional trajectory correction projectiles (ODTCP). In order to simplify the structure and reduce the cost,a scheme of adding a damping disc to the control cabin of ODTCP has been developed recently. The damping disc will unfold at the right moment during its flight to change the ballistic drift of rotary projectiles. Aimed at this technical scheme,a mathematical model of two-dimensional trajectory corrections was discussed according to the theory of exterior ballistics. An approximate formula for predicting the ballistic drift and trajectory correction was deduced. The capability of lateral trajectory correction and the flight stability of TDTCP were also analyzed. All the work is valuable for further research.展开更多
Color inconsistency between views is an important problem to be solved in multi-view video systems. A multi-view video color correction method using dynamic programming is proposed. Three-dimensional histograms are co...Color inconsistency between views is an important problem to be solved in multi-view video systems. A multi-view video color correction method using dynamic programming is proposed. Three-dimensional histograms are constructed with sequential conditional probability in HSI color space. Then, dynamic programming is used to seek the best color mapping relation with the minimum cost path between target image histogram and source image histogram. Finally, video tracking technique is performed to correct multi-view video. Experimental results show that the proposed method can obtain better subjective and objective performance in color correction.展开更多
By analyzing the traditional star-tracking correction technology,this paper studies the star-tracking direct correction method which is based on star sensor dynamic separation initial displacement angles and main erro...By analyzing the traditional star-tracking correction technology,this paper studies the star-tracking direct correction method which is based on star sensor dynamic separation initial displacement angles and main errors of inertial measure unit（IMU） in order to carry out automatic navigation and improve the hitting accuracy and quick reaction capability of near-earth flight vehicles.Through comprehensive application and improvement of the best correction factor method,this paper proposes the startracking comprehensive correction method which combines the two methods above-mentioned and the accelerometer dynamic error separation technology.The simulation results show that obvious effects can be achieved by using the star-tracking integrated correction method.展开更多
In this work,synchronous cutting of concave and convex surfaces was achieved using the duplex helical method for the hypoid gear,and the problem of tooth surface error correction was studied.First,the mathematical mod...In this work,synchronous cutting of concave and convex surfaces was achieved using the duplex helical method for the hypoid gear,and the problem of tooth surface error correction was studied.First,the mathematical model of the hypoid gears machined by the duplex helical method was established.Second,the coordinates of discrete points on the tooth surface were obtained by measurement center,and the normal errors of the discrete points were calculated.Third,a tooth surface error correction model is established,and the tooth surface error was corrected using the Levenberg-Marquard algorithm with trust region strategy and least square method.Finally,grinding experiments were carried out on the machining parameters obtained by Levenberg-Marquard algorithm with trust region strategy,which had a better effect on tooth surface error correction than the least square method.After the tooth surface error is corrected,the maximum absolute error is reduced from 30.9μm before correction to 6.8μm,the root mean square of the concave error is reduced from 15.1 to 2.1μm,the root mean square of the convex error is reduced from 10.8 to 1.8μm,and the sum of squared errors of the concave and convex surfaces was reduced from 15471 to 358μm^(2).It is verified that the Levenberg-Marquard algorithm with trust region strategy has a good accuracy for the tooth surface error correction of hypoid gear machined by duplex helical method.展开更多
This paper presents an actuator used for the trajectory correction fuze,which is subject to high impact loadings during launch.A simulation method is carried out to obtain the peak-peak stress value of each component,...This paper presents an actuator used for the trajectory correction fuze,which is subject to high impact loadings during launch.A simulation method is carried out to obtain the peak-peak stress value of each component,from which the ball bearings are possible failures according to the results.Subsequently,three schemes against impact loadings,full-element deep groove ball bearing and integrated raceway,needle roller thrust bearing assembly,and gaskets are utilized for redesigning the actuator to effectively reduce the bearings’stress.However,multi-objectives optimization still needs to be conducted for the gaskets to decrease the stress value further to the yield stress.Four gasket’s structure parameters and three bearings’peak-peak stress are served as the four optimization variables and three objectives,respectively.Optimized Latin hypercube design is used for generating sample points,and Kriging model selected according to estimation result can establish the relationship between the variables and objectives,representing the simulation which is time-consuming.Accordingly,two optimization algorithms work out the Pareto solutions,from which the best solutions are selected,and verified by the simulation to determine the gaskets optimized structure parameters.It can be concluded that the simulation and optimization method based on these components is effective and efficient.展开更多
A model of correcting the nonlinear error of photoelectric displacement sensor was established based on the least square support vector machine.The parameters of the correcting nonlinear model,such as penalty factor a...A model of correcting the nonlinear error of photoelectric displacement sensor was established based on the least square support vector machine.The parameters of the correcting nonlinear model,such as penalty factor and kernel parameter,were optimized by chaos genetic algorithm.And the nonlinear correction of photoelectric displacement sensor based on least square support vector machine was applied.The application results reveal that error of photoelectric displacement sensor is less than 1.5%,which is rather satisfactory for nonlinear correction of photoelectric displacement sensor.展开更多
In order to improve the data transmission reliability of mobile ad hoc network, a routing scheme called integrated forward error correction multipath routing protocol was proposed, which integrates the techniques of p...In order to improve the data transmission reliability of mobile ad hoc network, a routing scheme called integrated forward error correction multipath routing protocol was proposed, which integrates the techniques of packet fragmenting and forward error correction encoding into multipath routing. The scheme works as follows: adding a certain redundancy into the original packets; fragmenting the resulting packets into exclusive blocks of the same size; encoding with the forward error correction technique, and then sending them to the destination node. When the receiving end receives a certain amount of information blocks, the original information will be recovered even with partial loss. The performance of the scheme was evaluated using OPNET modeler. The experimental results show that with the method the average transmission delay is decreased by 20% and the transmission reliability is increased by 30%.展开更多
In conventional technical trajectory correction schemes,continuous attitude adjusting mechanisms, such as canards, are inferior in terms of response time and efficiency of executing instructions. Discontinuous attitud...In conventional technical trajectory correction schemes,continuous attitude adjusting mechanisms, such as canards, are inferior in terms of response time and efficiency of executing instructions. Discontinuous attitude adjusting mechanisms, such as the lateral pulse jet, have complex impact on the airflow layer of the projectile surface caused by the thrust vector jet flow. An improved two-dimensional trajectory correction mechanism is designed based on the principle of firing mass blocks by a tailor-made propellant. The mechanical properties of the thrust force(namely the correction force) is analyzed. The trajectory correction model is established to analyze the effects of correction starting moment and correction phase angle of a thrust force on the projectile's trajectory. According to the trajectory correction scheme, an improved genetic algorithm is employed to this work. The scheme is tested in the simulation. The results show that the correction scheme is effective to reduce target dispersion and increase the precision of the impact point.展开更多
Under the dual driven forces of soaring disputes and national policy,the dispute resolution ecosystem of China showed the mediation centralism,and the revival of mediation presented the characteristics of adversary sy...Under the dual driven forces of soaring disputes and national policy,the dispute resolution ecosystem of China showed the mediation centralism,and the revival of mediation presented the characteristics of adversary system.In order to comply with the modern rule of law system,the traditional mediation is incorporated into the modern legal system through the three-level transformation of"discipline of laws","introduction of procedures"and"specialized cultivation",which was promoted by the popularity of social governance,the input of the idea of diversified solutions and the pragmatic impetus under the pressure of social transformation.The mediation movement has the characteristics of both consciousness of pragmatism and the initial legalization,but will also face the mediation disorder.The remodeling of mediation must be rooted in systematization and modernization.Its development trend includes expansion of fields,symbiosis of autonomy and specialization,and mandatory introduction.展开更多
In this paper,various aberrations have been analyzed.Not only the effects of aberration on geometrical center position are taken into account,but also the deviation of displayed star position energy center caused by a...In this paper,various aberrations have been analyzed.Not only the effects of aberration on geometrical center position are taken into account,but also the deviation of displayed star position energy center caused by aberration is analyzed.These two aspects have been taken into comprehensive evaluation and star position correction.The correction method based on polar coordinates is proposed,and cumbersome partition correction and calculated quantity based on two-dimensional coordinates can be simplified.The experimental results show that the correction processing based on polar coordinates is simpler and easier compared with any other correction methods.In addition,the correction results are significantly more accurate.展开更多
Thanks to the fantastic development of power, transportation, chemical engineering, architecture and other fields, there has been an increasing demand for new type of section steel with large sections used for constru...Thanks to the fantastic development of power, transportation, chemical engineering, architecture and other fields, there has been an increasing demand for new type of section steel with large sections used for construction frame, such as type-H, type-T, and type-C section steel. New types of section steel usually are long and with large cross section. Therefore, for the sake of the cost, steel plate welding structure is used home and abroad. During the welding process, welding distortion seems unavoidable. Presently, proper welding machinery, technique and standards are adopted to minimize the distortion. Angular distortion is corrected with oil press and angular distortion corrector, while horizontal distortions like sickle curve and arch are mainly done with flame. Flame correction is of great labor intensity and is also time and material consuming. Besides, the correction is affected by the operators’ skill and mood, which, to some extent, limits the productivity. In this paper, a new technique of section steel distortion correction with high efficiency and adaptability and yet low investment and cost will be proposed for the development of new-type section steel. The correction principles and capability calculation should be done some research on, which will be introduced. The practice done on section steel with a wing edge of 40～60 mm, proves satisfactory: compared with oil-press correction, continual mangling correction saves equipment investment by three quarters, installed capacity by three quarters and investment by three quarters and with a much higher efficiency. Particularly in the distortion correction of heavy welding structures, mangling correction stands out from the crowd. Mangling correction proves to be the best solution to the continual horizontal distortion correction of welding section steel.展开更多
基金the National Natural Science Foundation of China(Grant No.61973033)Preliminary Research of Equipment(Grant No.9090102010305)for funding the experiments。
文摘The longitudinal dispersion of the projectile in shooting tests of two-dimensional trajectory corrections fused with fixed canards is extremely large that it sometimes exceeds the correction ability of the correction fuse actuator.The impact point easily deviates from the target,and thus the correction result cannot be readily evaluated.However,the cost of shooting tests is considerably high to conduct many tests for data collection.To address this issue,this study proposes an aiming method for shooting tests based on small sample size.The proposed method uses the Bootstrap method to expand the test data;repeatedly iterates and corrects the position of the simulated theoretical impact points through an improved compatibility test method;and dynamically adjusts the weight of the prior distribution of simulation results based on Kullback-Leibler divergence,which to some extent avoids the real data being"submerged"by the simulation data and achieves the fusion Bayesian estimation of the dispersion center.The experimental results show that when the simulation accuracy is sufficiently high,the proposed method yields a smaller mean-square deviation in estimating the dispersion center and higher shooting accuracy than those of the three comparison methods,which is more conducive to reflecting the effect of the control algorithm and facilitating test personnel to iterate their proposed structures and algorithms.;in addition,this study provides a knowledge base for further comprehensive studies in the future.
基金supported by the National Natural Science Foundation of China(62101099)the Chinese Postdoctoral Science Foundation(2021M690558,2022T150100,2018M633352,2019T120825)+3 种基金the Young Elite Scientist Sponsorship Program(YESS20200082)the Aeronautical Science Foundation of China(2022Z017080001)the Open Foundation of Science and Technology on Electronic Information Control Laboratorythe Natural Science Foundation of Sichuan Province(2023NSFSC1386)。
文摘The detection of hypersonic targets usually confronts range migration(RM)issue before coherent integration(CI).The traditional methods aiming at correcting RM to obtain CI mainly considers the narrow-band radar condition.However,with the increasing requirement of far-range detection,the time bandwidth product,which is corresponding to radar’s mean power,should be promoted in actual application.Thus,the echo signal generates the scale effect(SE)at large time bandwidth product situation,influencing the intra and inter pulse integration performance.To eliminate SE and correct RM,this paper proposes an effective algorithm,i.e.,scaled location rotation transform(ScLRT).The ScLRT can remove SE to obtain the matching pulse compression(PC)as well as correct RM to complete CI via the location rotation transform,being implemented by seeking the actual rotation angle.Compared to the traditional coherent detection algorithms,Sc LRT can address the SE problem to achieve better detection/estimation capabilities.At last,this paper gives several simulations to assess the viability of ScLRT.
基金supported by the National Natural Science Foundation of China(61473023)
文摘Magnetic field gradient tensor measurement is an important technique to obtain position information of magnetic objects. When using magnetic field sensors to measure magnetic field gradient as the coefficients of tensor, field differentiation is generally approximated by field difference. As a result, magnetic objects positioning by magnetic field gradient tensor measurement always involves an inherent error caused by sensor sizes, leading to a reduction in detectable distance and detectable angle. In this paper, the inherent positioning error caused by magnetic field gradient tensor measurement is calculated and corrected by iterations based on the systematic position error distribution patterns. The results show that, the detectable distance range and the angle range of an ac magnetic object（2.44 Am^2@1 kHz） can be increased from（0.45 m, 0.75 m）,（0？, 25？） to（0.30 m, 0.80 m）,（0？,80？）, respectively.
文摘Compared with the one-dimensional trajectory correction technology which adjusts longitudinal range, not only does the two-dimensional trajectory correction technology adjust the force in velocity direction, but also need to modulate the lateral force or trajectory (perpendicular to the vertical plane of fire direction). Therefore, the structure of control cabin of two-dimensional trajectory correction projectile (TDTCP) is more complicated than that of one-dimensional trajectory correction projectile (ODTCP). To simplify the structure of control cabin of TDTCP and reduce the cost, a scheme of adding a damping disk to the control cabin of ODTCP has been developed recently. The damping disk is unfolded at the right moment during its flight to change the ballistic drift of spin stabilized projectile. For this technical scheme of TDTCP, a fast and accurate impact point prediction method based on extended Kalman filter is presented. An approximate formula for predicting the ballistic drift and trajectory correction quantity is deduced. And the lateral correction capability for different fire angles and its influencing factors are analyzed. All the work is valuable for further research.
文摘A target localization algorithm,which uses the measurement information from onboard GPS and onboard laser detector to acquire the target position,is proposed to obtain the accurate position of ground target in real time in the trajectory correction process of semi-active laser terminal correction projectile.A target localization model is established according to projectile position,attitude and line-of-sight angle.The effects of measurement errors of projectile position,attitude and line-of-sight angle on localization accuracy at different quadrant elevation angles are analyzed through Monte-Carlo simulation.The simulation results show that the measurement error of line-of-sight angle has the largest influence on the localization accuracy.The localization accuracy decreases with the increase in quadrant elevation angle.However,the maximum localization accuracy is less than 7 m.The proposed algorithm meets the accuracy and real-time requirements of target localization.
基金Project(51176045) supported by the National Natural Science Foundation of China
文摘The algorithm of dense spectrum correction has been raised and proved based on the correction of discrete spectrum by fast Fourier transform.The result of simulation shows that such algorithm has advantages of high accuracy and small amount of calculation.The algorithm has been successfully applied to the analysis of vibration signals from internal combustion engine.To calculate discrete spectrum,fast Fourier transform has been used to calculate the discrete spectrum by the signals acquired by the sensors on the oil pan,and the signal has been extracted from the mixed signals.
文摘This work investigates the performance of various forward error correction codes, by which the MIMO-OFDM system is deployed. To ensure fair investigation, the performance of four modulations, namely, binary phase shift keying(BPSK), quadrature phase shift keying(QPSK), quadrature amplitude modulation(QAM)-16 and QAM-64 with four error correction codes(convolutional code(CC), Reed-Solomon code(RSC)+CC, low density parity check(LDPC)+CC, Turbo+CC) is studied under three channel models(additive white Guassian noise(AWGN), Rayleigh, Rician) and three different antenna configurations(2×2, 2×4, 4×4). The bit error rate(BER) and the peak signal to noise ratio(PSNR) are taken as the measures of performance. The binary data and the color image data are transmitted and the graphs are plotted for various modulations with different channels and error correction codes. Analysis on the performance measures confirm that the Turbo + CC code in 4×4 configurations exhibits better performance.
文摘The two-dimensional trajectory correction needs to adjust not only the force in velocity direction,but also the lateral force or lateral trajectory (normal to the perpendicular plane of fire direction) . Therefore,its structure of control cabin is more complicated than that of one-dimensional trajectory correction projectiles (ODTCP). In order to simplify the structure and reduce the cost,a scheme of adding a damping disc to the control cabin of ODTCP has been developed recently. The damping disc will unfold at the right moment during its flight to change the ballistic drift of rotary projectiles. Aimed at this technical scheme,a mathematical model of two-dimensional trajectory corrections was discussed according to the theory of exterior ballistics. An approximate formula for predicting the ballistic drift and trajectory correction was deduced. The capability of lateral trajectory correction and the flight stability of TDTCP were also analyzed. All the work is valuable for further research.
基金supported by the National Natural Science Foundation of China (60672073)the Program for New Century Excellent Talents in University (NCET-06-0537)+1 种基金the Natural Science Foundation of Ningbo (2008A610016)the K.C.Wong Magna Fund in Ningbo University.
文摘Color inconsistency between views is an important problem to be solved in multi-view video systems. A multi-view video color correction method using dynamic programming is proposed. Three-dimensional histograms are constructed with sequential conditional probability in HSI color space. Then, dynamic programming is used to seek the best color mapping relation with the minimum cost path between target image histogram and source image histogram. Finally, video tracking technique is performed to correct multi-view video. Experimental results show that the proposed method can obtain better subjective and objective performance in color correction.
文摘By analyzing the traditional star-tracking correction technology,this paper studies the star-tracking direct correction method which is based on star sensor dynamic separation initial displacement angles and main errors of inertial measure unit（IMU） in order to carry out automatic navigation and improve the hitting accuracy and quick reaction capability of near-earth flight vehicles.Through comprehensive application and improvement of the best correction factor method,this paper proposes the startracking comprehensive correction method which combines the two methods above-mentioned and the accelerometer dynamic error separation technology.The simulation results show that obvious effects can be achieved by using the star-tracking integrated correction method.
基金Projects(52075552,51575533,51805555,11662004)supported by the National Natural Science Foundation of China。
文摘In this work,synchronous cutting of concave and convex surfaces was achieved using the duplex helical method for the hypoid gear,and the problem of tooth surface error correction was studied.First,the mathematical model of the hypoid gears machined by the duplex helical method was established.Second,the coordinates of discrete points on the tooth surface were obtained by measurement center,and the normal errors of the discrete points were calculated.Third,a tooth surface error correction model is established,and the tooth surface error was corrected using the Levenberg-Marquard algorithm with trust region strategy and least square method.Finally,grinding experiments were carried out on the machining parameters obtained by Levenberg-Marquard algorithm with trust region strategy,which had a better effect on tooth surface error correction than the least square method.After the tooth surface error is corrected,the maximum absolute error is reduced from 30.9μm before correction to 6.8μm,the root mean square of the concave error is reduced from 15.1 to 2.1μm,the root mean square of the convex error is reduced from 10.8 to 1.8μm,and the sum of squared errors of the concave and convex surfaces was reduced from 15471 to 358μm^(2).It is verified that the Levenberg-Marquard algorithm with trust region strategy has a good accuracy for the tooth surface error correction of hypoid gear machined by duplex helical method.
基金The authors would like to acknowledge National Defense Pre-Research Foundation of China(Grant No.41419030102)to provide fund for conducting experiments.
文摘This paper presents an actuator used for the trajectory correction fuze,which is subject to high impact loadings during launch.A simulation method is carried out to obtain the peak-peak stress value of each component,from which the ball bearings are possible failures according to the results.Subsequently,three schemes against impact loadings,full-element deep groove ball bearing and integrated raceway,needle roller thrust bearing assembly,and gaskets are utilized for redesigning the actuator to effectively reduce the bearings’stress.However,multi-objectives optimization still needs to be conducted for the gaskets to decrease the stress value further to the yield stress.Four gasket’s structure parameters and three bearings’peak-peak stress are served as the four optimization variables and three objectives,respectively.Optimized Latin hypercube design is used for generating sample points,and Kriging model selected according to estimation result can establish the relationship between the variables and objectives,representing the simulation which is time-consuming.Accordingly,two optimization algorithms work out the Pareto solutions,from which the best solutions are selected,and verified by the simulation to determine the gaskets optimized structure parameters.It can be concluded that the simulation and optimization method based on these components is effective and efficient.
基金Project(50925727) supported by the National Fund for Distinguish Young Scholars of ChinaProject(60876022) supported by the National Natural Science Foundation of China+1 种基金Project(2010FJ4141) supported by Hunan Provincial Science and Technology Foundation,ChinaProject supported by the Fund of the Key Construction Academic Subject (Optics) of Hunan Province,China
文摘A model of correcting the nonlinear error of photoelectric displacement sensor was established based on the least square support vector machine.The parameters of the correcting nonlinear model,such as penalty factor and kernel parameter,were optimized by chaos genetic algorithm.And the nonlinear correction of photoelectric displacement sensor based on least square support vector machine was applied.The application results reveal that error of photoelectric displacement sensor is less than 1.5%,which is rather satisfactory for nonlinear correction of photoelectric displacement sensor.
基金Projects(2003CB314802) supported by the State Key Fundamental Research and Development Programof China project(90104001) supported by the National Natural Science Foundation of China
文摘In order to improve the data transmission reliability of mobile ad hoc network, a routing scheme called integrated forward error correction multipath routing protocol was proposed, which integrates the techniques of packet fragmenting and forward error correction encoding into multipath routing. The scheme works as follows: adding a certain redundancy into the original packets; fragmenting the resulting packets into exclusive blocks of the same size; encoding with the forward error correction technique, and then sending them to the destination node. When the receiving end receives a certain amount of information blocks, the original information will be recovered even with partial loss. The performance of the scheme was evaluated using OPNET modeler. The experimental results show that with the method the average transmission delay is decreased by 20% and the transmission reliability is increased by 30%.
基金supported by the National Natural Science Foundation of China(11372142)
文摘In conventional technical trajectory correction schemes,continuous attitude adjusting mechanisms, such as canards, are inferior in terms of response time and efficiency of executing instructions. Discontinuous attitude adjusting mechanisms, such as the lateral pulse jet, have complex impact on the airflow layer of the projectile surface caused by the thrust vector jet flow. An improved two-dimensional trajectory correction mechanism is designed based on the principle of firing mass blocks by a tailor-made propellant. The mechanical properties of the thrust force(namely the correction force) is analyzed. The trajectory correction model is established to analyze the effects of correction starting moment and correction phase angle of a thrust force on the projectile's trajectory. According to the trajectory correction scheme, an improved genetic algorithm is employed to this work. The scheme is tested in the simulation. The results show that the correction scheme is effective to reduce target dispersion and increase the precision of the impact point.
文摘Under the dual driven forces of soaring disputes and national policy,the dispute resolution ecosystem of China showed the mediation centralism,and the revival of mediation presented the characteristics of adversary system.In order to comply with the modern rule of law system,the traditional mediation is incorporated into the modern legal system through the three-level transformation of"discipline of laws","introduction of procedures"and"specialized cultivation",which was promoted by the popularity of social governance,the input of the idea of diversified solutions and the pragmatic impetus under the pressure of social transformation.The mediation movement has the characteristics of both consciousness of pragmatism and the initial legalization,but will also face the mediation disorder.The remodeling of mediation must be rooted in systematization and modernization.Its development trend includes expansion of fields,symbiosis of autonomy and specialization,and mandatory introduction.
文摘In this paper,various aberrations have been analyzed.Not only the effects of aberration on geometrical center position are taken into account,but also the deviation of displayed star position energy center caused by aberration is analyzed.These two aspects have been taken into comprehensive evaluation and star position correction.The correction method based on polar coordinates is proposed,and cumbersome partition correction and calculated quantity based on two-dimensional coordinates can be simplified.The experimental results show that the correction processing based on polar coordinates is simpler and easier compared with any other correction methods.In addition,the correction results are significantly more accurate.
文摘Thanks to the fantastic development of power, transportation, chemical engineering, architecture and other fields, there has been an increasing demand for new type of section steel with large sections used for construction frame, such as type-H, type-T, and type-C section steel. New types of section steel usually are long and with large cross section. Therefore, for the sake of the cost, steel plate welding structure is used home and abroad. During the welding process, welding distortion seems unavoidable. Presently, proper welding machinery, technique and standards are adopted to minimize the distortion. Angular distortion is corrected with oil press and angular distortion corrector, while horizontal distortions like sickle curve and arch are mainly done with flame. Flame correction is of great labor intensity and is also time and material consuming. Besides, the correction is affected by the operators’ skill and mood, which, to some extent, limits the productivity. In this paper, a new technique of section steel distortion correction with high efficiency and adaptability and yet low investment and cost will be proposed for the development of new-type section steel. The correction principles and capability calculation should be done some research on, which will be introduced. The practice done on section steel with a wing edge of 40～60 mm, proves satisfactory: compared with oil-press correction, continual mangling correction saves equipment investment by three quarters, installed capacity by three quarters and investment by three quarters and with a much higher efficiency. Particularly in the distortion correction of heavy welding structures, mangling correction stands out from the crowd. Mangling correction proves to be the best solution to the continual horizontal distortion correction of welding section steel.
