At room temperature, the bias dependence of a far-infrared electroluminescence image of a photodiode is investi-gated in the dark condition. The results show that the electroluminescence image can be used to detect de...At room temperature, the bias dependence of a far-infrared electroluminescence image of a photodiode is investi-gated in the dark condition. The results show that the electroluminescence image can be used to detect defects in the photodiode. Additionally, it is found that the electroluminescence intensity has a power law dependence on the dc bias current. The photodiode ideality factor could be obtained by a fitting a relationship between the electroluminescence intensity and the bias current. The device defect levels will be easily determined according to the infrared image and the extracted ideality factor value. This work is of guiding significance for current solar cell testing and research.展开更多
Blue-green electroluminescence has been observed in free-standing diamond films which were deposited by microwave plasma assisted CVD on silicon substrates.The electroluminescence device is driven by a 60 Hz power sup...Blue-green electroluminescence has been observed in free-standing diamond films which were deposited by microwave plasma assisted CVD on silicon substrates.The electroluminescence device is driven by a 60 Hz power supply.The threshold voltage was about 112 V peak-to-peak.The electroluminescence spectrum at room temperature,showed a blue-green band with the peak centered at 485nm suggesting band A type emission.Electroluminescence was also observed at 77K.展开更多
In order to investigate the inherent polarization intensity in InGaN/GaN multiple quantum well(MQW) structures,the electroluminescence(EL) spectra of three samples with different GaN barrier thicknesses of 21.3 nm, 11...In order to investigate the inherent polarization intensity in InGaN/GaN multiple quantum well(MQW) structures,the electroluminescence(EL) spectra of three samples with different GaN barrier thicknesses of 21.3 nm, 11.4 nm, and 6.5 nm are experimentally studied. All of the EL spectra present a similar blue-shift under the low-level current injection,and then turns to a red-shift tendency when the current increases to a specific value, which is defined as the turning point.The value of this turning point differs from one another for the three InGaN/GaN MQW samples. Sample A, which has the GaN barrier thickness of 21.3 nm, shows the highest current injection level at the turning point as well as the largest value of blue-shift. It indicates that sample A has the maximum intensity of the polarization field. The red-shift of the EL spectra results from the vertical electron leakage in InGaN/GaN MQWs and the corresponding self-heating effect under the high-level current injection. As a result, it is an effective approach to evaluate the polarization field in the InGaN/GaN MQW structures by using the injection current level at the turning point and the blue-shift of the EL spectra profiles.展开更多
A GaN/Si nanoheterojunction is prepared through growing Ga N nanocrystallites（nc-GaN） on a silicon nanoporous pillar array（Si-NPA） by a chemical vapor deposition（CVD） technique at a relatively low temperature. T...A GaN/Si nanoheterojunction is prepared through growing Ga N nanocrystallites（nc-GaN） on a silicon nanoporous pillar array（Si-NPA） by a chemical vapor deposition（CVD） technique at a relatively low temperature. The average size of nc-Ga N is determined to be ~10 nm. The spectral measurements disclose that the photoluminescence（PL） from GaN/SiNPA is composed of an ultraviolet（UV） band and a broad band spanned from UV to red region, with the feature that the latter band is similar to that of electroluminescence（EL）. The electron transition from the energy levels of conduction band and, or, shallow donors to that of deep acceptors of Ga N is indicated to be responsible for both the broad-band PL and the EL luminescence. A study of the I-V characteristic shows that at a low forward bias, the current across the heterojunction is contact-limited while at a high forward bias it is bulk-limited, which follows the thermionic emission model and space-charge-limited current（SCLC） model, respectively. The bandgap offset analysis indicates that the carrier transport is dominated by electron injection from n-GaN into the p-Si-NPA, and the EL starts to appear only when holes begin to be injected from Si-NPA into GaN with biases higher than a threshold voltage.展开更多
An n-ZnO：A1/p-boron-doped diamond heterostructure electroluminescent device is produced, and a rectifying be- havior can be observed. The electroluminescence spectrum at room temperature exhibits two visible bands ce...An n-ZnO：A1/p-boron-doped diamond heterostructure electroluminescent device is produced, and a rectifying be- havior can be observed. The electroluminescence spectrum at room temperature exhibits two visible bands centred at 450 nm-485 nm （blue emission） and 570 nm-640 nm （yellow emission）. Light emission with a luminance of 15 cd/m2 is observed from the electroluminescent device at a forward applied voltage of 85 V, which is distinguished from white light by the naked eye.展开更多
A simplified n-ZnO/p-Si heterojunction has been prepared by growing n-type ZnO rods on p-type silicon wafer through the chemical wpour deposition method. The reflectance spectrum of the sample shows an independent abs...A simplified n-ZnO/p-Si heterojunction has been prepared by growing n-type ZnO rods on p-type silicon wafer through the chemical wpour deposition method. The reflectance spectrum of the sample shows an independent absorption peak at 384 nm, which may be originated from the bound states at the junction. In the photoluminescence spectrum a new emission band is shown at 393 nm, besides the bandedge emission at 380nm. The electroluminescence spectrum of the n-ZnO/p-Si heterojunction shows a stable yellow luminescence band centred at 560 nm, which can be attributed to the emission from trapped states. Another kind of discrete ZnO rod has also been prepared on such silicon wafer and is encapsulated with carbonated polystyrene for electroluminescence detection. This composite structure shows a weak ultraviolet electroluminescence band at 395 nm and a yellow electroluminescence band. These data prove that surface modification which blocks the transverse movement of carriers between neighbouring nanorods plays important roles in the ultraviolet emission of ZnO nanorods. These findings are vital for future display device design.展开更多
A new electroluminescence device is fabricated by microwave plasma chemical vapour deposition system and electron beam vapour deposition system. It is comprised of highly doped silicon/diamond/boron/nitrogen-doped dia...A new electroluminescence device is fabricated by microwave plasma chemical vapour deposition system and electron beam vapour deposition system. It is comprised of highly doped silicon/diamond/boron/nitrogen-doped diamond/indium tin oxide thin films. Effects of process parameters on morphologies and structures of the thin films are detected and analysed by scanning electron microscopy, Raman spectrometer and x-ray photoelectron spectrometer. A direct-current （DC） power supply is used to drive the electroluminescence device. The blue light emission with a luminance of 1.2 cd·m^-2 is observed from this double-doped diamond thin film electroluminescence device at an applied voltage of 105 V.展开更多
Tensile-strained Ge/SiGe multiple quantum wells （MQWs） were grown on a Ge-on-Si virtual substrate using ultrahigh vacuum chemical vapor deposition on an n＋-Si （001） substrate. Direct-bandgap electroluminescence f...Tensile-strained Ge/SiGe multiple quantum wells （MQWs） were grown on a Ge-on-Si virtual substrate using ultrahigh vacuum chemical vapor deposition on an n＋-Si （001） substrate. Direct-bandgap electroluminescence from the MQWs light emitting diode was observed at room temperature. The quantum confinement effect of the direct-bandgap transitions is in good agreement with the theoretical calculated results. The redshift mechanism of emission wavelength related to the thermal effect is discussed,展开更多
We report a lateral Ge-on-Si ridge waveguide light emitting diode （LED） grown by ultrahigh vacuum chemical vapor deposition （UHV-CVD）. Direct-bandgap electroluminescence （EL） of Ge waveguide under continuous cur...We report a lateral Ge-on-Si ridge waveguide light emitting diode （LED） grown by ultrahigh vacuum chemical vapor deposition （UHV-CVD）. Direct-bandgap electroluminescence （EL） of Ge waveguide under continuous current is observed at room temperature. The heat-enhancing luminescence and thermal radiation-induced superlinear increase of edge output optical power are found. The spontaneous emission and thermal radiation based on the generalized Planck radiation law are calculated and fit very well to the experimental results. The Ge waveguides with different lengths are studied and the shorter one shows stronger EL intensity.展开更多
The internal behaviors of carriers in InGaAsP single-junction solar cell are investigated by using electroluminescence(EL) measurements. Two emission peaks can be observed in current-dependent electroluminescence spec...The internal behaviors of carriers in InGaAsP single-junction solar cell are investigated by using electroluminescence(EL) measurements. Two emission peaks can be observed in current-dependent electroluminescence spectra at low temperatures, and carrier localization exists for both peaks under low excitation. The trends of power index α extracted from excitation-dependent EL spectra at different temperatures imply that there exists a competition between Shockley–Read–Hall recombination and Auger recombination. Auger recombination becomes dominant at high temperatures, which is probably responsible for the lower current density of InGaAsP solar cell. Besides, the anomalous “S-shape” tendency with the temperature of band-edge peak position can be attributed to potential fluctuation and carrier redistribution, demonstrating delocalization, transfer, and redistribution of carriers in the continuum band-edge. Furthermore, the strong reduction of activation energy at high excitations indicates that electrons and holes escaped independently, and the faster-escaping carriers are holes.展开更多
InGaN-based green light-emitting diodes （LEDs） with different growth temperatures of superlattice grown on Si （111） substrates are investigated by temperature-dependent electroluminescence between 100 K and 350K. ...InGaN-based green light-emitting diodes （LEDs） with different growth temperatures of superlattice grown on Si （111） substrates are investigated by temperature-dependent electroluminescence between 100 K and 350K. It is observed that with the decrease of the growth temperature of the superlattice from 895℃ to 855℃, the forward voltage decreases, especially at low temperature. We presume that this is due to the existence of the larger average size of V-shaped pits, which is determined by secondary ion mass spectrometer measurements. Meanwhile, the sample with higher growth temperature of superlattice shows a severer efficiency droop at cryogenic temperatures （about 100 K-150 K）. Electron overflow into p-GaN is considered to be the cause of such phenomena, which is relevant to the poorer hole injection into multiple quantum wells and the more reduced effective active volume in the active region.展开更多
In GaN-based green light-emitting diodes（LEDs） with and without Mg-preflow before the growth of p-Al GaN electron blocking layer（EBL） are investigated experimentally.A higher Mg doping concentration is achieved in...In GaN-based green light-emitting diodes（LEDs） with and without Mg-preflow before the growth of p-Al GaN electron blocking layer（EBL） are investigated experimentally.A higher Mg doping concentration is achieved in the EBL after Mg-preflow treatment,effectively alleviating the commonly observed efficiency collapse and electrons overflowing at cryogenic temperatures.However,unexpected decline in quantum efficiency is observed after Mg-preflow treatment at room temperature.Our conclusions are drawn such that the efficiency decline is probably the result of different emission positions.Higher Mg doping concentration in the EBL after Mg-preflow treatment will make it easier for a hole to be injected into multiple quantum wells with emission closer to pGaN side through the（8-plane rather than the V-shape pits,which is not favorable to luminous efficiency due to the preferred occurrence of accumulated strain relaxation and structural defects in upper QWs closer to p-GaN.Within this framework,apparently disparate experimental observations regarding electroluminescence properties,in this work,are well reconciled.展开更多
The in.jection of charge carriers from the electron/hole injection or transport layers in polymer light-emitting diodes potentially increases the device efficiency not by changing of charge intensity but by lattice di...The in.jection of charge carriers from the electron/hole injection or transport layers in polymer light-emitting diodes potentially increases the device efficiency not by changing of charge intensity but by lattice distortion variation and quasi-particle interactions. From the low-dimensional condensed matter physics perspective, a valid mechanism is proposed to bring a type of novel channels that, under a proper external electric field, transition- forbidden triplet excitons are transformed and partially charged by charge carriers （polarons/bipolarons）, thus are able to emit light and to enhance fluorescence greatly.展开更多
Metal halide perovskites have emerged as promising light-emitting materials for next-generation displays owing to their remarkable material characteristics including broad color tunability,pure color emission with rem...Metal halide perovskites have emerged as promising light-emitting materials for next-generation displays owing to their remarkable material characteristics including broad color tunability,pure color emission with remarkably narrow bandwidths,high quantum yield,and solution processability.Despite recent advances have pushed the luminance efficiency of monochromic perovskite light-emitting diodes(PeLEDs)to their theoretical limits,their current fabrication using the spincoating process poses limitations for fabrication of full-color displays.To integrate PeLEDs into full-color display panels,it is crucial to pattern red–green–blue(RGB)perovskite pixels,while mitigating issues such as cross-contamination and reductions in luminous efficiency.Herein,we present state-of-the-art patterning technologies for the development of full-color PeLEDs.First,we highlight recent advances in the development of efficient PeLEDs.Second,we discuss various patterning techniques of MPHs(i.e.,photolithography,inkjet printing,electron beam lithography and laserassisted lithography,electrohydrodynamic jet printing,thermal evaporation,and transfer printing)for fabrication of RGB pixelated displays.These patterning techniques can be classified into two distinct approaches:in situ crystallization patterning using perovskite precursors and patterning of colloidal perovskite nanocrystals.This review highlights advancements and limitations in patterning techniques for PeLEDs,paving the way for integrating PeLEDs into full-color panels.展开更多
This paper reports that the polymer/organic heterojunction doped light-emitting diodes using a novel poly-TPD as hole transport material and doping both hole transport layer and emitter layer with the highly fluoresce...This paper reports that the polymer/organic heterojunction doped light-emitting diodes using a novel poly-TPD as hole transport material and doping both hole transport layer and emitter layer with the highly fluorescent rubrene and DCJTB has been successfully fabricated. The basic structure of the heterostructure is PTPD/Alq3. When hole transport layer and electron transport layer are doped simultaneously with different dopant, the electrol quantum efficiencies are about 3 times greater than that of the undoped device. Compared with undoped device and conventional TPD/Alq3 diode, the stability of the doping device is significantly improved. The process of emission for doped device may include carrier trapping as well as FSrster energy transfer.展开更多
Single-molecule devices not only promise to provide an alternative strategy to break through the miniaturization and functionalization bottlenecks faced by traditional semiconductor devices,but also provide a reliable...Single-molecule devices not only promise to provide an alternative strategy to break through the miniaturization and functionalization bottlenecks faced by traditional semiconductor devices,but also provide a reliable platform for exploration of the intrinsic properties of matters at the single-molecule level.Because the regulation of the electrical properties of single-molecule devices will be a key factor in enabling further advances in the development of molecular electronics,it is necessary to clarify the interactions between the charge transport occurring in the device and the external fields,particularly the optical field.This review mainly introduces the optoelectronic effects that are involved in single-molecule devices,including photoisomerization switching,photoconductance,plasmon-induced excitation,photovoltaic effect,and electroluminescence.We also summarize the optoelectronic mechanisms of single-molecule devices,with particular emphasis on the photoisomerization,photoexcitation,and photo-assisted tunneling processes.Finally,we focus the discussion on the opportunities and challenges arising in the single-molecule optoelectronics field and propose further possible breakthroughs.展开更多
The charge readout of a liquid xenon(LXe)detector via proportional scintillation in the liquid phase was first realized by the Waseda group 40 years ago,but the technical challenges involved were overwhelming.Although...The charge readout of a liquid xenon(LXe)detector via proportional scintillation in the liquid phase was first realized by the Waseda group 40 years ago,but the technical challenges involved were overwhelming.Although the tests were successful,this method was finally discarded and eventually nearly forgotten.Currently,this approach is not considered for large LXe dark matter detectors.Instead,the dual-phase technology was selected despite many limitations and challenges.In two independent studies,two groups from Columbia University and Shanghai Jiao Tong University reevaluated proportional scintillation in the liquid phase.Both studies established the merits for very large LXe detectors,but the Columbia group also encountered apparent limitations,namely the shadowing of the light by the anode wires,and a dependence of the pulse shape on the drift path of the electrons in the anode region.The differences between the two studies,however,are not intrinsic to the technique,but a direct consequence of the chosen geometry.Taking the geometrical differences into account,the results match without ambiguity.They also agree with the original results from the Waseda group.展开更多
We introduce a thin LiF layer into tris-8-hydroxyquinoline aluminium （Alq3 ） based bilayer organic light-emitting devices to block hole transport. By varying the thickness and position of this LiF layer in Alq3, we ...We introduce a thin LiF layer into tris-8-hydroxyquinoline aluminium （Alq3 ） based bilayer organic light-emitting devices to block hole transport. By varying the thickness and position of this LiF layer in Alq3, we obtain an electroluminescent efficiency increase by a factor of two with respect to the control devices without a LiF blocking layer. By using a 10nm dye doped Alq3 sensor layer, we prove that LiF can block holes and excitons effectively. Experimental results suggest that the thin LiF layer may be a good hole and exciton blocking layer.展开更多
We present a new method in which both positive and negative pulses are used to etch silicon for fabrication of porous silicon （PS） monolayer. The optical thickness and morphology of PS monolayer fabricated with diff...We present a new method in which both positive and negative pulses are used to etch silicon for fabrication of porous silicon （PS） monolayer. The optical thickness and morphology of PS monolayer fabricated with different negative pulse voltages are investigated by means of reflectance spectra, scanning electron microscopy and photoluminescence spectra. It is found that with this method the PS monolayer is thicker and more uniform. The micropores also appear to be more regular than those made by common positive pulse etching. This phenomenon is attributed to the vertical etching effect of the PS monolayer being strengthened while lateral etching process is restrained. The explanation we propose is that negative pulse can help the hydrogen cations （H^＋） in the electrolyte move into the micropores of PS monolayer. These H^＋ ions combine with the Si atoms on the wall of new-formed micropores, leading to formation of Si-H bonds. The formation of Silt bonds results in a hole depletion layer near the micropore wall surface, which decreases hole density on the surface, preventing the micropore wall from being eroded laterally by F^- anions. Therefore during the positive pulse period the etching reaction occurs exclusively only at the bottom of the micropores where lots of holes are provided by the anode.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 10904059,41066001,61072131,61177096)Aeronautical Science Foundation of China (Grant No. 2010ZB56004)+3 种基金the Scientific Research Foundation of Jiangxi Provincial Department of Education,China (Grant No. GJJ11176)the Open Fund of the Key Laboratory of Nondestructive Testing(Ministry of Education,Nanchang Hangkong University) (Grant No. ZD201029005)the Natural Science Foundation of JiangxiProvince,China (Grant No. 2009GZW0024)the Graduate Innovation Base of Jiangxi Province,China
文摘At room temperature, the bias dependence of a far-infrared electroluminescence image of a photodiode is investi-gated in the dark condition. The results show that the electroluminescence image can be used to detect defects in the photodiode. Additionally, it is found that the electroluminescence intensity has a power law dependence on the dc bias current. The photodiode ideality factor could be obtained by a fitting a relationship between the electroluminescence intensity and the bias current. The device defect levels will be easily determined according to the infrared image and the extracted ideality factor value. This work is of guiding significance for current solar cell testing and research.
基金the National Natural Science Foundation of China,and the Natural Science Foundation of He'nan province.
文摘Blue-green electroluminescence has been observed in free-standing diamond films which were deposited by microwave plasma assisted CVD on silicon substrates.The electroluminescence device is driven by a 60 Hz power supply.The threshold voltage was about 112 V peak-to-peak.The electroluminescence spectrum at room temperature,showed a blue-green band with the peak centered at 485nm suggesting band A type emission.Electroluminescence was also observed at 77K.
基金Project supported by the National Key Research and Development Program of China(Grant Nos.2016YFB0400803 and 2016YFB0401801)the National Natural Science Foundation of China(Grant Nos.61674138,61674139,61604145,61574135,and 61574134)。
文摘In order to investigate the inherent polarization intensity in InGaN/GaN multiple quantum well(MQW) structures,the electroluminescence(EL) spectra of three samples with different GaN barrier thicknesses of 21.3 nm, 11.4 nm, and 6.5 nm are experimentally studied. All of the EL spectra present a similar blue-shift under the low-level current injection,and then turns to a red-shift tendency when the current increases to a specific value, which is defined as the turning point.The value of this turning point differs from one another for the three InGaN/GaN MQW samples. Sample A, which has the GaN barrier thickness of 21.3 nm, shows the highest current injection level at the turning point as well as the largest value of blue-shift. It indicates that sample A has the maximum intensity of the polarization field. The red-shift of the EL spectra results from the vertical electron leakage in InGaN/GaN MQWs and the corresponding self-heating effect under the high-level current injection. As a result, it is an effective approach to evaluate the polarization field in the InGaN/GaN MQW structures by using the injection current level at the turning point and the blue-shift of the EL spectra profiles.
基金Project supported by the National Natural Science Foundation of China(Grant No.61176044)
文摘A GaN/Si nanoheterojunction is prepared through growing Ga N nanocrystallites（nc-GaN） on a silicon nanoporous pillar array（Si-NPA） by a chemical vapor deposition（CVD） technique at a relatively low temperature. The average size of nc-Ga N is determined to be ~10 nm. The spectral measurements disclose that the photoluminescence（PL） from GaN/SiNPA is composed of an ultraviolet（UV） band and a broad band spanned from UV to red region, with the feature that the latter band is similar to that of electroluminescence（EL）. The electron transition from the energy levels of conduction band and, or, shallow donors to that of deep acceptors of Ga N is indicated to be responsible for both the broad-band PL and the EL luminescence. A study of the I-V characteristic shows that at a low forward bias, the current across the heterojunction is contact-limited while at a high forward bias it is bulk-limited, which follows the thermionic emission model and space-charge-limited current（SCLC） model, respectively. The bandgap offset analysis indicates that the carrier transport is dominated by electron injection from n-GaN into the p-Si-NPA, and the EL starts to appear only when holes begin to be injected from Si-NPA into GaN with biases higher than a threshold voltage.
基金supported by the Shanghai Human Resources and Social Security Bureau,China(Grant No.2009023)
文摘An n-ZnO：A1/p-boron-doped diamond heterostructure electroluminescent device is produced, and a rectifying be- havior can be observed. The electroluminescence spectrum at room temperature exhibits two visible bands centred at 450 nm-485 nm （blue emission） and 570 nm-640 nm （yellow emission）. Light emission with a luminance of 15 cd/m2 is observed from the electroluminescent device at a forward applied voltage of 85 V, which is distinguished from white light by the naked eye.
基金Project supported by the National Natural Science Foundation of China （Grant No 20173073）, National 973 Project （Grant No 2002CB713802）, Nano- and Bio-device Key Project of CAS, 985 Project of Hunan University.
文摘A simplified n-ZnO/p-Si heterojunction has been prepared by growing n-type ZnO rods on p-type silicon wafer through the chemical wpour deposition method. The reflectance spectrum of the sample shows an independent absorption peak at 384 nm, which may be originated from the bound states at the junction. In the photoluminescence spectrum a new emission band is shown at 393 nm, besides the bandedge emission at 380nm. The electroluminescence spectrum of the n-ZnO/p-Si heterojunction shows a stable yellow luminescence band centred at 560 nm, which can be attributed to the emission from trapped states. Another kind of discrete ZnO rod has also been prepared on such silicon wafer and is encapsulated with carbonated polystyrene for electroluminescence detection. This composite structure shows a weak ultraviolet electroluminescence band at 395 nm and a yellow electroluminescence band. These data prove that surface modification which blocks the transverse movement of carriers between neighbouring nanorods plays important roles in the ultraviolet emission of ZnO nanorods. These findings are vital for future display device design.
基金supported by the Shanghai Education Committee of China (Grant No.07ZZ95)the Shanghai Human Resources and Social Security Bureau (Grant No.2009023)
文摘A new electroluminescence device is fabricated by microwave plasma chemical vapour deposition system and electron beam vapour deposition system. It is comprised of highly doped silicon/diamond/boron/nitrogen-doped diamond/indium tin oxide thin films. Effects of process parameters on morphologies and structures of the thin films are detected and analysed by scanning electron microscopy, Raman spectrometer and x-ray photoelectron spectrometer. A direct-current （DC） power supply is used to drive the electroluminescence device. The blue light emission with a luminance of 1.2 cd·m^-2 is observed from this double-doped diamond thin film electroluminescence device at an applied voltage of 105 V.
基金supported by the National Basic Research Program of China(Grant No.2013CB632103)the National Natural Science Foundation of China(Grant Nos.61036003,61176013,and 61177038)the High Technology Research and Development Program of China(Grant No.2011AA010302)
文摘Tensile-strained Ge/SiGe multiple quantum wells （MQWs） were grown on a Ge-on-Si virtual substrate using ultrahigh vacuum chemical vapor deposition on an n＋-Si （001） substrate. Direct-bandgap electroluminescence from the MQWs light emitting diode was observed at room temperature. The quantum confinement effect of the direct-bandgap transitions is in good agreement with the theoretical calculated results. The redshift mechanism of emission wavelength related to the thermal effect is discussed,
基金Project supported by the National Basic Research Program of China(Grant No.2013CB632103)the National Natural Science Foundation of China(Grant Nos.61176013 and 61036003)the Science Fund from Beijing Science and Technology Commission,China(Grant No.Z151100003315019)
文摘We report a lateral Ge-on-Si ridge waveguide light emitting diode （LED） grown by ultrahigh vacuum chemical vapor deposition （UHV-CVD）. Direct-bandgap electroluminescence （EL） of Ge waveguide under continuous current is observed at room temperature. The heat-enhancing luminescence and thermal radiation-induced superlinear increase of edge output optical power are found. The spontaneous emission and thermal radiation based on the generalized Planck radiation law are calculated and fit very well to the experimental results. The Ge waveguides with different lengths are studied and the shorter one shows stronger EL intensity.
基金Project supported by the National Key Research and Development Program,China (Grant No.2018YFB2003305)the National Natural Science Foundation of China (Grant Nos.61774165 and 61827823)the Key Laboratory Fund in Suzhou Institute of Suzhou Nano-Tech and NanoBionis (SINANO),Chinese Academy of Sciences (Grant No.Y4JAQ21005)。
文摘The internal behaviors of carriers in InGaAsP single-junction solar cell are investigated by using electroluminescence(EL) measurements. Two emission peaks can be observed in current-dependent electroluminescence spectra at low temperatures, and carrier localization exists for both peaks under low excitation. The trends of power index α extracted from excitation-dependent EL spectra at different temperatures imply that there exists a competition between Shockley–Read–Hall recombination and Auger recombination. Auger recombination becomes dominant at high temperatures, which is probably responsible for the lower current density of InGaAsP solar cell. Besides, the anomalous “S-shape” tendency with the temperature of band-edge peak position can be attributed to potential fluctuation and carrier redistribution, demonstrating delocalization, transfer, and redistribution of carriers in the continuum band-edge. Furthermore, the strong reduction of activation energy at high excitations indicates that electrons and holes escaped independently, and the faster-escaping carriers are holes.
基金Supported by the National Natural Science Foundation of China under Grant No 61334001the National Key Research and Development Program of China under Grant Nos 2016YFB0400600,2016YFB0400601 and 2016YFB0400100+1 种基金the National Science Foundation for Young Scientists of China under Grant No 21405076the Fund for Less Developed Regions of the National Natural Science Foundation of China under Grant No 11364034
文摘InGaN-based green light-emitting diodes （LEDs） with different growth temperatures of superlattice grown on Si （111） substrates are investigated by temperature-dependent electroluminescence between 100 K and 350K. It is observed that with the decrease of the growth temperature of the superlattice from 895℃ to 855℃, the forward voltage decreases, especially at low temperature. We presume that this is due to the existence of the larger average size of V-shaped pits, which is determined by secondary ion mass spectrometer measurements. Meanwhile, the sample with higher growth temperature of superlattice shows a severer efficiency droop at cryogenic temperatures （about 100 K-150 K）. Electron overflow into p-GaN is considered to be the cause of such phenomena, which is relevant to the poorer hole injection into multiple quantum wells and the more reduced effective active volume in the active region.
基金Supported by the National Key R&D Program of China under Grant Nos 2016YFB0400600 and 2016YFB0400601the State Key Program of the National Natural Science of China under Grant No 61334001+2 种基金the Key R&D Program of Jiangxi Province under Grant No 20165ABC28007the Natural Science Foundation of Jiangxi Province under Grant No 20151BAB207053the National Natural Science Foundation of China under Grant No 21405076
文摘In GaN-based green light-emitting diodes（LEDs） with and without Mg-preflow before the growth of p-Al GaN electron blocking layer（EBL） are investigated experimentally.A higher Mg doping concentration is achieved in the EBL after Mg-preflow treatment,effectively alleviating the commonly observed efficiency collapse and electrons overflowing at cryogenic temperatures.However,unexpected decline in quantum efficiency is observed after Mg-preflow treatment at room temperature.Our conclusions are drawn such that the efficiency decline is probably the result of different emission positions.Higher Mg doping concentration in the EBL after Mg-preflow treatment will make it easier for a hole to be injected into multiple quantum wells with emission closer to pGaN side through the（8-plane rather than the V-shape pits,which is not favorable to luminous efficiency due to the preferred occurrence of accumulated strain relaxation and structural defects in upper QWs closer to p-GaN.Within this framework,apparently disparate experimental observations regarding electroluminescence properties,in this work,are well reconciled.
文摘The in.jection of charge carriers from the electron/hole injection or transport layers in polymer light-emitting diodes potentially increases the device efficiency not by changing of charge intensity but by lattice distortion variation and quasi-particle interactions. From the low-dimensional condensed matter physics perspective, a valid mechanism is proposed to bring a type of novel channels that, under a proper external electric field, transition- forbidden triplet excitons are transformed and partially charged by charge carriers （polarons/bipolarons）, thus are able to emit light and to enhance fluorescence greatly.
基金the National Research Foundation of Korea(NRF)grant funded by the Korean government(MSIT)(Grant No.2021R1C1C1007997).
文摘Metal halide perovskites have emerged as promising light-emitting materials for next-generation displays owing to their remarkable material characteristics including broad color tunability,pure color emission with remarkably narrow bandwidths,high quantum yield,and solution processability.Despite recent advances have pushed the luminance efficiency of monochromic perovskite light-emitting diodes(PeLEDs)to their theoretical limits,their current fabrication using the spincoating process poses limitations for fabrication of full-color displays.To integrate PeLEDs into full-color display panels,it is crucial to pattern red–green–blue(RGB)perovskite pixels,while mitigating issues such as cross-contamination and reductions in luminous efficiency.Herein,we present state-of-the-art patterning technologies for the development of full-color PeLEDs.First,we highlight recent advances in the development of efficient PeLEDs.Second,we discuss various patterning techniques of MPHs(i.e.,photolithography,inkjet printing,electron beam lithography and laserassisted lithography,electrohydrodynamic jet printing,thermal evaporation,and transfer printing)for fabrication of RGB pixelated displays.These patterning techniques can be classified into two distinct approaches:in situ crystallization patterning using perovskite precursors and patterning of colloidal perovskite nanocrystals.This review highlights advancements and limitations in patterning techniques for PeLEDs,paving the way for integrating PeLEDs into full-color panels.
文摘This paper reports that the polymer/organic heterojunction doped light-emitting diodes using a novel poly-TPD as hole transport material and doping both hole transport layer and emitter layer with the highly fluorescent rubrene and DCJTB has been successfully fabricated. The basic structure of the heterostructure is PTPD/Alq3. When hole transport layer and electron transport layer are doped simultaneously with different dopant, the electrol quantum efficiencies are about 3 times greater than that of the undoped device. Compared with undoped device and conventional TPD/Alq3 diode, the stability of the doping device is significantly improved. The process of emission for doped device may include carrier trapping as well as FSrster energy transfer.
基金We acknowledge primary financial supports from the National Key R&D Program of China(2017YFA0204901,2021YFA1200101 and 2021YFA1200102)the National Natural Science Foundation of China(22150013,21727806,21933001 and 22173050)+1 种基金the Tencent Foundation through the XPLORER PRIZE“Frontiers Science Center for New Organic Matter”at Nankai University(63181206).
文摘Single-molecule devices not only promise to provide an alternative strategy to break through the miniaturization and functionalization bottlenecks faced by traditional semiconductor devices,but also provide a reliable platform for exploration of the intrinsic properties of matters at the single-molecule level.Because the regulation of the electrical properties of single-molecule devices will be a key factor in enabling further advances in the development of molecular electronics,it is necessary to clarify the interactions between the charge transport occurring in the device and the external fields,particularly the optical field.This review mainly introduces the optoelectronic effects that are involved in single-molecule devices,including photoisomerization switching,photoconductance,plasmon-induced excitation,photovoltaic effect,and electroluminescence.We also summarize the optoelectronic mechanisms of single-molecule devices,with particular emphasis on the photoisomerization,photoexcitation,and photo-assisted tunneling processes.Finally,we focus the discussion on the opportunities and challenges arising in the single-molecule optoelectronics field and propose further possible breakthroughs.
基金supported by a Grant from the Ministry of Science and Technology of China(No.2016YFA0400301)。
文摘The charge readout of a liquid xenon(LXe)detector via proportional scintillation in the liquid phase was first realized by the Waseda group 40 years ago,but the technical challenges involved were overwhelming.Although the tests were successful,this method was finally discarded and eventually nearly forgotten.Currently,this approach is not considered for large LXe dark matter detectors.Instead,the dual-phase technology was selected despite many limitations and challenges.In two independent studies,two groups from Columbia University and Shanghai Jiao Tong University reevaluated proportional scintillation in the liquid phase.Both studies established the merits for very large LXe detectors,but the Columbia group also encountered apparent limitations,namely the shadowing of the light by the anode wires,and a dependence of the pulse shape on the drift path of the electrons in the anode region.The differences between the two studies,however,are not intrinsic to the technique,but a direct consequence of the chosen geometry.Taking the geometrical differences into account,the results match without ambiguity.They also agree with the original results from the Waseda group.
基金Supported by the National Natural Science Foundation of China under Grant No 10504044, and the Fok Ying Tung Education Foundation under Grant No 101007.
文摘We introduce a thin LiF layer into tris-8-hydroxyquinoline aluminium （Alq3 ） based bilayer organic light-emitting devices to block hole transport. By varying the thickness and position of this LiF layer in Alq3, we obtain an electroluminescent efficiency increase by a factor of two with respect to the control devices without a LiF blocking layer. By using a 10nm dye doped Alq3 sensor layer, we prove that LiF can block holes and excitons effectively. Experimental results suggest that the thin LiF layer may be a good hole and exciton blocking layer.
基金Supported by the National Key Basic Research Programme of China, and the National Natural Science Foundation of China under Grant No 10321003.
文摘We present a new method in which both positive and negative pulses are used to etch silicon for fabrication of porous silicon （PS） monolayer. The optical thickness and morphology of PS monolayer fabricated with different negative pulse voltages are investigated by means of reflectance spectra, scanning electron microscopy and photoluminescence spectra. It is found that with this method the PS monolayer is thicker and more uniform. The micropores also appear to be more regular than those made by common positive pulse etching. This phenomenon is attributed to the vertical etching effect of the PS monolayer being strengthened while lateral etching process is restrained. The explanation we propose is that negative pulse can help the hydrogen cations （H^＋） in the electrolyte move into the micropores of PS monolayer. These H^＋ ions combine with the Si atoms on the wall of new-formed micropores, leading to formation of Si-H bonds. The formation of Silt bonds results in a hole depletion layer near the micropore wall surface, which decreases hole density on the surface, preventing the micropore wall from being eroded laterally by F^- anions. Therefore during the positive pulse period the etching reaction occurs exclusively only at the bottom of the micropores where lots of holes are provided by the anode.
