As an advanced device for observing atmospheric winds,the spaceborne Doppler Asymmetric Spatial Heterodyne(DASH)interferometer also encounters challenges associated with phase distortion,par-ticularly in limb sounding...As an advanced device for observing atmospheric winds,the spaceborne Doppler Asymmetric Spatial Heterodyne(DASH)interferometer also encounters challenges associated with phase distortion,par-ticularly in limb sounding scenarios.This paper discusses interferogram modeling and phase distortion cor-rection techniques for spaceborne DASH interferometers.The modeling of phase distortion interferograms with and without Doppler shift for limb observation was conducted,and the effectiveness of the analytical expression was verified through numerical simulation.The simulation results indicate that errors propagate layer by layer while using the onion-peeling inversion algorithm to handle phase-distorted interferograms.In contrast,the phase distortion correction algorithm can achieve effective correction.This phase correction method can be successfully applied to correct phase distortions in the interferograms of the spaceborne DASH interferometer,providing a feasible solution to enhance its measurement accuracy.展开更多
Oriented graphene aerogels have limited applica-tions because the flexibility of their graphene sheets and mi-crostructure give them a low skeleton strength,insufficient compression resilience,and poor flexibility.We ...Oriented graphene aerogels have limited applica-tions because the flexibility of their graphene sheets and mi-crostructure give them a low skeleton strength,insufficient compression resilience,and poor flexibility.We report the preparation of novel aerogel materials with a much better per-formance.Using the driving force of graphene oxide(GO)self-assembly andπ-πinteractions,carbon nanotubes(CNTs)were attached to the GO sheets,and an oriented composite carbon skeleton was constructed using“hydro-plastic foam-ing”.The introduction of CNTs significantly increased the strength of the skeleton and gave the aerogel an excellent re-versible compressibility.The innovative use of cold pressing greatly improved the thermal conductivity and flexibility of the aerogel,providing new ideas for the development of high-performance aerogels.Tests show that the obtained graphene composite aerogel has a reversible compressive strain of over 90%and can withstand 500 compression cycles along the direc-tion of pore accumulation.It can endure more than 10000 bending cycles perpendicular to the direction of composite carbon layer stacking,and its in-plane thermal conductivity reaches 64.5 W·m^(-1)·K^(-1).When filled with phase change materials,the high porosity of the carbon skeleton enables the material to have a high phase change filling rate,and its phase change enthalpy is greater than 150 J/g.Thanks to the exceptional flexibility of the carbon skeleton,the macrostructure of phase change materials can be bent as needed to adapt to thermal management scenarios and conform to device shapes.This significantly enhances practical application compatibility,providing flexible support for temperature control and thermal management across diverse device forms.展开更多
Restoration of phase aberrations is crucial for addressing atmospheric turbulence in light propagation.Traditional restoration algorithms based on Zernike polynomials(ZPs)often encounter challenges related to high com...Restoration of phase aberrations is crucial for addressing atmospheric turbulence in light propagation.Traditional restoration algorithms based on Zernike polynomials(ZPs)often encounter challenges related to high computational complexity and insufficient capture of high-frequency phase aberration components,so we proposed a Principal-Component-Analysis-based method for representing phase aberrations.This paper discusses the factors influencing the accuracy of restoration,mainly including the sample space size and the sampling interval of D/r_(0),on the basis of characterizing phase aberrations by Principal Components(PCs).The experimental results show that a larger D/r_(0)sampling interval can ensure the generalization ability and robustness of the principal components in the case of a limited amount of original data,which can help to achieve high-precision deployment of the model in practical applications quickly.In the environment with relatively strong turbulence in the test set of D/r_(0)=24,the use of 34 terms of PCs can improve the corrected Strehl ratio(SR)from 0.007 to 0.1585,while the Strehl ratio of the light spot after restoration using 34 terms of ZPs is only 0.0215,demonstrating almost no correction effect.The results indicate that PCs can serve as a better alternative in representing and restoring the characteristics of atmospheric turbulence induced phase aberrations.These findings pave the way to use PCs of phase aberrations with fewer terms than traditional ZPs to achieve data dimensionality reduction,and offer a reference to accelerate and stabilize the model and deep learning based adaptive optics correction.展开更多
Pb(Zr,Ti)O_(3)-Pb(Zn_(1/3)Nb_(2/3))O_(3) (PZT-PZN) based ceramics, as important piezoelectric materials, have a wide range of applications in fields such as sensors and actuators, thus the optimization of their piezoe...Pb(Zr,Ti)O_(3)-Pb(Zn_(1/3)Nb_(2/3))O_(3) (PZT-PZN) based ceramics, as important piezoelectric materials, have a wide range of applications in fields such as sensors and actuators, thus the optimization of their piezoelectric properties has been a hot research topic. This study investigated the effects of phase boundary engineering and domain engineering on (1-x)[0.8Pb(Zr_(0.5)Ti_(0.5))O_(3)-0.2Pb(Zn_(1/3)Nb_(2/3))O_(3)]-xBi(Zn_(0.5)Ti_(0.5))O_(3) ((1-x)(0.8PZT-0.2PZN)- xBZT) ceramic to obtain excellent piezoelectric properties. The crystal phase structure and microstructure of ceramic samples were characterized. The results showed that all samples had a pure perovskite structure, and the addition of BZT gradually increased the grain size. The addition of BZT caused a phase transition in ceramic samples from the morphotropic phase boundary (MPB) towards the tetragonal phase region, which is crucial for optimizing piezoelectric properties. By adjusting content of BZT and precisely controlling position of the phase boundary, the piezoelectric performance can be optimized. Domain structure is one of the key factors affecting piezoelectric performance. By using domain engineering techniques to optimize grain size and domain size, piezoelectric properties of ceramic samples have been significantly improved. Specifically, excellent piezoelectric properties (piezoelectric constant d_(33)=320 pC/N, electromechanical coupling factor kp=0.44) were obtained simultaneously for x=0.08. Based on experimental results and theoretical analysis, influence mechanisms of phase boundary engineering and domain engineering on piezoelectric properties were explored. The study shows that addition of BZT not only promotes grain growth, but also optimizes the domain structure, enabling the polarization reversal process easier, thereby improving piezoelectric properties. These research results not only provide new ideas for the design of high-performance piezoelectric ceramics, but also lay a theoretical foundation for development of related electronic devices.展开更多
During the propagation of high-power lasers within internal channels,the laser beam heats the propagation medium,causing the thermal blooming effect that degrades the beam quality at the output.The intricate configura...During the propagation of high-power lasers within internal channels,the laser beam heats the propagation medium,causing the thermal blooming effect that degrades the beam quality at the output.The intricate configuration of the optical path within the internal channel necessitates complex and time-consuming efforts to assess the impact of thermal blooming effect on the optical path.To meet the engineering need for rapid evaluation of thermal blooming effect in optical paths,this study proposed a rapid simulation method for the thermal blooming effect in internal optical paths based on the finite element method.This method discretized the fluid region into infinitesimal elements and employed finite element method for flow field analysis.A simplified analytical model of the flow field region in complex internal channels was established,and regions with similar thermal blooming effect were divided within this model.Based on the calculated optical path differences within these regions,numerical simulations of phase distortion caused by thermal blooming were conducted.The calculated result were compared with those obtained using the existing methods.The findings reveal that for complex optical paths,the discrepancy between the two approaches is less than 3.6%,with similar phase distortion patterns observed.For L-type units,this method and the existing methods identify the same primary factors influencing aberrations and exhibit consistent trends in their variation.This method was used to analyze the impact of thermal blooming effect in a straight channel under different gravity directions.The results show that phase distortion varies with changes in the direction of gravity,and the magnitude of the phase difference is strongly correlated with the component of gravity perpendicular to the optical axis.Compared to the existing methods,this approach offers greater flexibility,obviates the need for complex custom analysis programming.The analytical results of this method enable a rapid assessment of the thermal blooming effect in optical paths within the internal channel.This is especially useful during the engineering design.These results also provide crucial references for developing strategies to suppress thermal blooming effect.展开更多
An in-pixel histogramming time-to-digital converter(hTDC)based on octonary search and 4-tap phase detection is presented,aiming to improve frame rate while ensuring high precicion.The proposed hTDC is a 12-bit two-ste...An in-pixel histogramming time-to-digital converter(hTDC)based on octonary search and 4-tap phase detection is presented,aiming to improve frame rate while ensuring high precicion.The proposed hTDC is a 12-bit two-step converter consisting of a 6-bit coarse quantization and a 6-bit fine quantization,which supports a time resolution of 120 ps and multiphoton counting up to 2 GHz without a GHz reference frequency.The proposed hTDC is designed in 0.11μm CMOS process with an area consumption of 6900μm^(2).The data from a behavioral-level model is imported into the designed hTDC circuit for simulation verification.The post-simulation results show that the proposed hTDC achieves 0.8%depth precision in 9 m range for short-range system design specifications and 0.2%depth precision in 48 m range for long-range system design specifications.Under 30×10^(3) lux background light conditions,the proposed hTDC can be used for SPAD-based flash LiDAR sensor to achieve a frame rate to 40 fps with 200 ps resolution in 9 m range.展开更多
In this paper,we study the orthogonal time frequency space signal transmission over multi-path channel in the presence of phase noise(PHN)at both sides of millimeter wave(mmWave)communication links.The statistics char...In this paper,we study the orthogonal time frequency space signal transmission over multi-path channel in the presence of phase noise(PHN)at both sides of millimeter wave(mmWave)communication links.The statistics characteristics of the PHN-induced common phase error and inter-Doppler interference are investigated.Then,a column-shaped pilot structure is designed,and training pilots are used to realize linear-complexity PHN tracking and compensation.Numerical results demonstrate that the proposed scheme enables the signal to noise ratio loss to be restrained within 1 dB in contrast to the no PHN case.展开更多
Al-doped manganese dioxide(MnO_(2))was synthesized by simple hydrothermal method,and a controllable phase transition of the MnO_(2)crystal phase fromβtoδwas achieved.The effects of Al doping concentration on the str...Al-doped manganese dioxide(MnO_(2))was synthesized by simple hydrothermal method,and a controllable phase transition of the MnO_(2)crystal phase fromβtoδwas achieved.The effects of Al doping concentration on the structure and electrochemical properties of electrode materials were studied in detail.The results show that the controlled synthesis requires a synergy between KMnO_(4),MnCl_(2)and AlCl_(3),and that Al^(3+)plays an important role.Compared with the pure phase MnO_(2),the crystallinity of Al-doped MnO_(2)decreases and the specific surface area increases,which provides more active sites for the electrode material.When 3 mmol Al^(3+)is added,the prepared MnO_(2)-3 has the largest specific capacitance and the highest rate performance.The energy density of the asymmetric supercapacitor(ASC)with MnO_(2)-3 as the positive electrode and activated carbon(AC)as the negative electrode can reach 18.4 W·h/kg at the power density of 400 W/kg,and the capacity can maintain 90%of the initial value after 20000 cycles,indicating that Al-doped MnO_(2)has certain practical application value.This study provides favorable guidance for MnO_(2)as a high performance electrode material.展开更多
Nickel laterite ore is an important nickel-bearing mineral.Research on pre-heating and hydrogen pre-reduction in the pyrometallurgical process of nickel laterite ore is very limited,especially when using fluidized bed...Nickel laterite ore is an important nickel-bearing mineral.Research on pre-heating and hydrogen pre-reduction in the pyrometallurgical process of nickel laterite ore is very limited,especially when using fluidized bed roasting.This study systematically explores the mechanisms of fluidized bed pre-heating treatment and hydrogen pre-reduction in the roasting process of saprolitic nickel laterite ore.According to single-factor experiment results,the appropriate pre-heating and pre-reduction conditions were a pre-heating temperature of 700℃,a pre-heating time of 30 min,a pre-reduction temperature of 700℃,a pre-reduction time of 30 min,and a hydrogen concentration of 80%.Then,the nickel metallization rate and iron metallization rate reached 90.56%and 41.31%,respectively.Various analytical and testing methods were employed to study the changes in phase composition,magnetism,surface element valence states,and microstructure of nickel laterite ore during fluidized pre-heating and pre-reduction.The study shows that hydrogen can achieve nickel reduction at relatively low temperatures.It was also found that pre-heating treatment of nickel laterite ore is beneficial.Pre-heating opens up the mineral structures of serpentine and limonite,allowing the reducing gas and nickel to interact quickly during the reduction process,enhancing the pre-reduction process.展开更多
The phase transformation of galena in H_(2)SO_(4)-Fe_(2)(SO_(4))_(3) system under oxygen pressure was investigated.Results indicated that the critical conditions for the phase transformation of galena into lead jarosi...The phase transformation of galena in H_(2)SO_(4)-Fe_(2)(SO_(4))_(3) system under oxygen pressure was investigated.Results indicated that the critical conditions for the phase transformation of galena into lead jarosite(Pb-J)were 130℃,30 g/L H_(2)SO_(4),15 g/L Fe^(3+),and an oxygen partial pressure of 0.4 MPa.Furthermore,increased Fe^(3+)concentration and oxygen partial pressure did not enhance jarosite formation.Conversely,lowering the temperature and increasing the H_(2)SO_(4) concentration facilitated PbSO_(4) formation and inhibited its further conversion to Pb-J.Additionally,the effects of potassium sulfate,sodium sulfate,and high concentrations of zinc sulfate on the phase transformation of galena were examined through leaching tests,XRD,SEM-EDS,and FT-IR analyses.All three sulfates inhibited the conversion of galena to Pb-J.Among these,potassium sulfate prevented Pb-J formation and converted it more thoroughly into potassium jarosite.However,high concentrations of zinc sulfate facilitated the crystallization of both PbSO_(4) and Pb-J,which altered the morphology of the product.Zinc ions coprecipitated with Pb-J,thereby integrating into the product.展开更多
Trace amounts of Zr and V can increase the recrystallization temperature of Al-Mg-Si wrought aluminum alloys,which is expected to regulate the recrystallization grain.In this paper,trace amounts of V and Zr were added...Trace amounts of Zr and V can increase the recrystallization temperature of Al-Mg-Si wrought aluminum alloys,which is expected to regulate the recrystallization grain.In this paper,trace amounts of V and Zr were added to recycled Al-Mg-Si alloys,and their e ffects on the microstructure and mechanical properties of the cast alloys were studied by scanning electron microscopy(SEM)and synchrotron radiation X-ray tomography(SRXT).The results show that the addition of Zr significantly increases the grain sizes due to the“Zr poisoning”;V addition has no significant effect on the grain size.The morphology of Fe-rich phase gradually changes from the large Chinese-script shape to the fine short rod and curved long strip shape,and the distribution uniformity is improved with the combined addition of V and Zr.The three-dimensional(3 D)morphology of Fe-rich phase includes granular,short rod-like,simple branch and multi-branch structures.The individual addition of V and Zr has no significant effect on the morphology of Fe-rich phase;but the combined addition of V and Zr significantly increases the number and volume fraction of Fe-rich phase with small size(diameter£15μm),the number of branches in the largest Fe-rich phase is significantly reduced,resulting in the improvement of elongation.This work provides a theoretical basis for the development of new recycled Al-Mg-Si alloys in industrial application.展开更多
Nowadays, ultrafine explosives are widely used in military fields. Ultrafine 2,2',4,4',6,6'-hexanitrostilbene(HNS) has emerged as an optimal primer for explosion foil initiators due to its excellent therma...Nowadays, ultrafine explosives are widely used in military fields. Ultrafine 2,2',4,4',6,6'-hexanitrostilbene(HNS) has emerged as an optimal primer for explosion foil initiators due to its excellent thermal stability and high-voltage short-pulse initiation performance. However, the solid phase ripening of ultrafine HNS leads to a degradation in its impact detonation performance. Previous studies have indicated that residual dimethyl formamide(DMF), which is present in ultrafine HNS prepared using the recrystallization method, affects ultrafine HNS ripening. The mechanism of residual solvent effects on solid phase ripening of ultrafine HNS is unclear. In this work, the specific surface area(SSA) derived from small angle X-ray scattering(SAXS) was utilized for kinetic fitting analysis to explore the mechanism by which residual solvents enhance the solid phase ripening of ultrafine HNS. The results of the SSA measured by insitu SAXS under conditions of 150℃ for 40 h revealed that the sample with 0.2% residual DMF exhibited a 21.51% decrease in SSA, whereas the sample with only 0.04% residual DMF showed a decrease of 15.66%.Furthermore, the higher amounts of residual DMF accelerated the reduction in SSA with time. Kinetic fitting analysis demonstrated that reducing residual DMF would lower both the activation energy and the pre-exponential factor, consequently decreasing the rate constant of solid phase ripening. The mechanism was speculated that it primarily facilitated the Ostwald ripening(OR). Additionally, contrast variation small angle X-ray scattering(CV-SAXS) confirmed that coating of ultrafine HNS particles is an effective method for inhibiting ripening, significantly reducing both the rate and extent of ripening of ultrafine HNS. This study predicts how residual solvents impact the solid phase ripening process of ultrafine HNS and proposes strategies for enhancing the long-term stability of ultrafine explosives.展开更多
Ultrathin 2D niobium oxide dichloride(NbOCl_(2))is an emerging member of the 2D ferroelectric material family with extensive potential to provide multifunctionality in electronic devices and nanophotonics elements.It ...Ultrathin 2D niobium oxide dichloride(NbOCl_(2))is an emerging member of the 2D ferroelectric material family with extensive potential to provide multifunctionality in electronic devices and nanophotonics elements.It exhibits negligible interlayer electronic coupling and significant excitonic behavior in the bulk state.Here we substantiate that NbOCl_(2) nanosheets can be exfoliated and effectively size-selected using controlled centrifugation techniques by the liquid phase exfoliation(LPE)method.Spectroscopic measurements displayed that the variations in dispersion were highly dependent on the nanosheet dimensions.The nanosheets seemed to be comparatively defect-free which will be further corroborated by high resolution transmission electron microscopy(HRTEM)and Raman analysis.The size selected nanosheets are unanticipated stable in isopropyl alcohol(IPA),possibly owing to the protective influence of a solvation shell.Additionally,the photothermal conversion response and photothermal stability of nanosized NbOCl_(2) were investigated.Our finding revealed that NbOCl_(2) possesses a robust photothermal agent property,boasting a photothermal conversion efficiency of more than 30%.This underscores its promising potential for various photothermal applications in different fields such as photothermal therapy and thermal energy conversion.展开更多
With the continuous expansion of deep underground engineering and the growing demand for safety monitoring,microseismic monitoring has become a core method for early warning of rock mass fracture and engineering stabi...With the continuous expansion of deep underground engineering and the growing demand for safety monitoring,microseismic monitoring has become a core method for early warning of rock mass fracture and engineering stability assessment.To address problems in existing methods,such as low data processing efficiency and poor phase recognition accuracy under low signal-to-noise ratio(SNR)conditions in complex geological environments,this study proposes an intelligent phase picking model based on ResUNet.The model integrates the residual learning mechanism of ResNet with the multi-scale feature extraction capability of UNet,effectively mitigating the vanishing gradient problem in deep networks.It also achieves cross-layer fusion of shallow detail features and deep semantic features through skip connections in the encoder-decoder structure.Compared with traditional short-time average/long-time average(STA/LTA)algorithms and advanced neural network models such as PhaseNet and EQTransformer,ResUNet shows superior performance in picking P-and S-wave phases.The model was trained on 400000 labeled microseismic signals from the Stanford earthquake dataset(STEAD)and was successfully applied to the Shizhuyuan polymetallic mine in Hunan Province,China.The results demonstrate that ResUNet achieves high picking accuracy and robustness in complex geological conditions,offering reliable technical support for early warning of disasters such as rockburst in deep underground engineering.展开更多
Most of the existing direction of arrival(DOA)estimation algorithms are applied under the assumption that the array manifold is ideal.In practical engineering applications,the existence of non-ideal conditions such as...Most of the existing direction of arrival(DOA)estimation algorithms are applied under the assumption that the array manifold is ideal.In practical engineering applications,the existence of non-ideal conditions such as mutual coupling between array elements,array amplitude and phase errors,and array element position errors leads to defects in the array manifold,which makes the performance of the algorithm decline rapidly or even fail.In order to solve the problem of DOA estimation in the presence of amplitude and phase errors and array element position errors,this paper introduces the first-order Taylor expansion equivalent model of the received signal under the uniform linear array from the Bayesian point of view.In the solution,the amplitude and phase error parameters and the array element position error parameters are regarded as random variables obeying the Gaussian distribution.At the same time,the expectation-maximization algorithm is used to update the probability distribution parameters,and then the two error parameters are solved alternately to obtain more accurate DOA estimation results.Finally,the effectiveness of the proposed algorithm is verified by simulation and experiment.展开更多
Simple cubic black phosphorus(BP)has been recognized as a strategic material due to its exceptional structural stability under extreme conditions.In this investigation,simple cubic BP was successfully synthesized thro...Simple cubic black phosphorus(BP)has been recognized as a strategic material due to its exceptional structural stability under extreme conditions.In this investigation,simple cubic BP was successfully synthesized through shock-induced phase transformation,utilizing amorphous red phosphorus as the precursor material.The phase evolution process was systematically investigated using plane shock loading apparatus,with shock pressure and temperature parameters being precisely controlled to optimize transformation kinetics.Comprehensive phase characterization revealed the correlation between thermodynamic loading profiles and cubic BP formation efficiency.Precursor modification strategies were implemented through orthorhombic BP utilization,resulting in enhanced cubic phase yield and crystallinity.The synthesized cubic BP variants are considered promising candidates for advanced protective material systems,particularly where combinations of mechanical resilience and thermal stability are required under extreme operational conditions.This research provides critical insights into shock-induced phase transformation mechanics,while establishing foundational protocols for manufacturing non-equilibrium materials with potential applications in next-generation defensive technologies.展开更多
In the field of deep space exploration,the rapid development of terahertz spectrometer has put forward higher requirements to the back-end chirp transform spectrometer(CTS)system.In order to simultaneously meet the me...In the field of deep space exploration,the rapid development of terahertz spectrometer has put forward higher requirements to the back-end chirp transform spectrometer(CTS)system.In order to simultaneously meet the measurement requirements of wide bandwidth and high accuracy spectral lines,we built a CTS system with an analysis bandwidth of 1 GHz and a frequency resolution of 100 kHz around the surface acoustic wave(SAW)chirp filter with a bandwidth of 1 GHz.In this paper,the relationship between the CTS nonlinear phase error shift model and the basic measurement parameters is studied,and the effect of CTS phase mismatch on the pulse compression waveform is analyzed by simulation.And the expander error optimization method is proposed for the problem that the large nonlinear error of the expander leads to the unbalanced response of the CTS system and the serious distortion of the compressed pulse waveform under large bandwidth.It is verified through simulation and experiment that the method is effective for reducing the root mean square error(RMSE)of the phase of the expander from 18.75°to 6.65°,reducing the in-band standard deviation of the CTS frequency resolution index from 8.43 kHz to 4.72 kHz,solving the problem of serious distortion of the compressed pulse waveform,and improving the uneven CTS response under large bandwidth.展开更多
Ni/TiO_(2) catalyst is widely employed for photo-driven DRM reaction while the influence of crystal structure of TiO_(2) remains unclear.In this work,the rutile/anatase ratio in supports was successfully controlled by...Ni/TiO_(2) catalyst is widely employed for photo-driven DRM reaction while the influence of crystal structure of TiO_(2) remains unclear.In this work,the rutile/anatase ratio in supports was successfully controlled by varying the calcination temperature of anatase-TiO_(2).Structural characterizations revealed that a distinct TiO_(x) coating on the Ni nanoparticles(NPs)was evident for Ni/TiO_(2)-700 catalyst due to strong metal-support interaction.It is observed that the TiOx overlayer gradually disappeared as the ratio of rutile/anatase increased,thereby enhancing the exposure of Ni active sites.The exposed Ni sites enhanced visible light absorption and boosted the dissociation capability of CH4,which led to the much elevated catalytic activity for Ni/TiO_(2)-950 in which rutile dominated.Therefore,the catalytic activity of solar-driven DRM reaction was significantly influenced by the rutile/anatase ratio.Ni/TiO_(2)-950,characterized by a predominant rutile phase,exhibited the highest DRM reactivity,with remarkable H_(2) and CO production rates reaching as high as 87.4 and 220.2 mmol/(g·h),respectively.These rates were approximately 257 and 130 times higher,respectively,compared to those obtained on Ni/TiO_(2)-700 with anatase.This study suggests that the optimization of crystal structure of TiO_(2) support can effectively enhance the performance of photothermal DRM reaction.展开更多
文摘As an advanced device for observing atmospheric winds,the spaceborne Doppler Asymmetric Spatial Heterodyne(DASH)interferometer also encounters challenges associated with phase distortion,par-ticularly in limb sounding scenarios.This paper discusses interferogram modeling and phase distortion cor-rection techniques for spaceborne DASH interferometers.The modeling of phase distortion interferograms with and without Doppler shift for limb observation was conducted,and the effectiveness of the analytical expression was verified through numerical simulation.The simulation results indicate that errors propagate layer by layer while using the onion-peeling inversion algorithm to handle phase-distorted interferograms.In contrast,the phase distortion correction algorithm can achieve effective correction.This phase correction method can be successfully applied to correct phase distortions in the interferograms of the spaceborne DASH interferometer,providing a feasible solution to enhance its measurement accuracy.
文摘Oriented graphene aerogels have limited applica-tions because the flexibility of their graphene sheets and mi-crostructure give them a low skeleton strength,insufficient compression resilience,and poor flexibility.We report the preparation of novel aerogel materials with a much better per-formance.Using the driving force of graphene oxide(GO)self-assembly andπ-πinteractions,carbon nanotubes(CNTs)were attached to the GO sheets,and an oriented composite carbon skeleton was constructed using“hydro-plastic foam-ing”.The introduction of CNTs significantly increased the strength of the skeleton and gave the aerogel an excellent re-versible compressibility.The innovative use of cold pressing greatly improved the thermal conductivity and flexibility of the aerogel,providing new ideas for the development of high-performance aerogels.Tests show that the obtained graphene composite aerogel has a reversible compressive strain of over 90%and can withstand 500 compression cycles along the direc-tion of pore accumulation.It can endure more than 10000 bending cycles perpendicular to the direction of composite carbon layer stacking,and its in-plane thermal conductivity reaches 64.5 W·m^(-1)·K^(-1).When filled with phase change materials,the high porosity of the carbon skeleton enables the material to have a high phase change filling rate,and its phase change enthalpy is greater than 150 J/g.Thanks to the exceptional flexibility of the carbon skeleton,the macrostructure of phase change materials can be bent as needed to adapt to thermal management scenarios and conform to device shapes.This significantly enhances practical application compatibility,providing flexible support for temperature control and thermal management across diverse device forms.
文摘Restoration of phase aberrations is crucial for addressing atmospheric turbulence in light propagation.Traditional restoration algorithms based on Zernike polynomials(ZPs)often encounter challenges related to high computational complexity and insufficient capture of high-frequency phase aberration components,so we proposed a Principal-Component-Analysis-based method for representing phase aberrations.This paper discusses the factors influencing the accuracy of restoration,mainly including the sample space size and the sampling interval of D/r_(0),on the basis of characterizing phase aberrations by Principal Components(PCs).The experimental results show that a larger D/r_(0)sampling interval can ensure the generalization ability and robustness of the principal components in the case of a limited amount of original data,which can help to achieve high-precision deployment of the model in practical applications quickly.In the environment with relatively strong turbulence in the test set of D/r_(0)=24,the use of 34 terms of PCs can improve the corrected Strehl ratio(SR)from 0.007 to 0.1585,while the Strehl ratio of the light spot after restoration using 34 terms of ZPs is only 0.0215,demonstrating almost no correction effect.The results indicate that PCs can serve as a better alternative in representing and restoring the characteristics of atmospheric turbulence induced phase aberrations.These findings pave the way to use PCs of phase aberrations with fewer terms than traditional ZPs to achieve data dimensionality reduction,and offer a reference to accelerate and stabilize the model and deep learning based adaptive optics correction.
基金National Natural Science Foundation of China (52202139, 52072178)。
文摘Pb(Zr,Ti)O_(3)-Pb(Zn_(1/3)Nb_(2/3))O_(3) (PZT-PZN) based ceramics, as important piezoelectric materials, have a wide range of applications in fields such as sensors and actuators, thus the optimization of their piezoelectric properties has been a hot research topic. This study investigated the effects of phase boundary engineering and domain engineering on (1-x)[0.8Pb(Zr_(0.5)Ti_(0.5))O_(3)-0.2Pb(Zn_(1/3)Nb_(2/3))O_(3)]-xBi(Zn_(0.5)Ti_(0.5))O_(3) ((1-x)(0.8PZT-0.2PZN)- xBZT) ceramic to obtain excellent piezoelectric properties. The crystal phase structure and microstructure of ceramic samples were characterized. The results showed that all samples had a pure perovskite structure, and the addition of BZT gradually increased the grain size. The addition of BZT caused a phase transition in ceramic samples from the morphotropic phase boundary (MPB) towards the tetragonal phase region, which is crucial for optimizing piezoelectric properties. By adjusting content of BZT and precisely controlling position of the phase boundary, the piezoelectric performance can be optimized. Domain structure is one of the key factors affecting piezoelectric performance. By using domain engineering techniques to optimize grain size and domain size, piezoelectric properties of ceramic samples have been significantly improved. Specifically, excellent piezoelectric properties (piezoelectric constant d_(33)=320 pC/N, electromechanical coupling factor kp=0.44) were obtained simultaneously for x=0.08. Based on experimental results and theoretical analysis, influence mechanisms of phase boundary engineering and domain engineering on piezoelectric properties were explored. The study shows that addition of BZT not only promotes grain growth, but also optimizes the domain structure, enabling the polarization reversal process easier, thereby improving piezoelectric properties. These research results not only provide new ideas for the design of high-performance piezoelectric ceramics, but also lay a theoretical foundation for development of related electronic devices.
文摘During the propagation of high-power lasers within internal channels,the laser beam heats the propagation medium,causing the thermal blooming effect that degrades the beam quality at the output.The intricate configuration of the optical path within the internal channel necessitates complex and time-consuming efforts to assess the impact of thermal blooming effect on the optical path.To meet the engineering need for rapid evaluation of thermal blooming effect in optical paths,this study proposed a rapid simulation method for the thermal blooming effect in internal optical paths based on the finite element method.This method discretized the fluid region into infinitesimal elements and employed finite element method for flow field analysis.A simplified analytical model of the flow field region in complex internal channels was established,and regions with similar thermal blooming effect were divided within this model.Based on the calculated optical path differences within these regions,numerical simulations of phase distortion caused by thermal blooming were conducted.The calculated result were compared with those obtained using the existing methods.The findings reveal that for complex optical paths,the discrepancy between the two approaches is less than 3.6%,with similar phase distortion patterns observed.For L-type units,this method and the existing methods identify the same primary factors influencing aberrations and exhibit consistent trends in their variation.This method was used to analyze the impact of thermal blooming effect in a straight channel under different gravity directions.The results show that phase distortion varies with changes in the direction of gravity,and the magnitude of the phase difference is strongly correlated with the component of gravity perpendicular to the optical axis.Compared to the existing methods,this approach offers greater flexibility,obviates the need for complex custom analysis programming.The analytical results of this method enable a rapid assessment of the thermal blooming effect in optical paths within the internal channel.This is especially useful during the engineering design.These results also provide crucial references for developing strategies to suppress thermal blooming effect.
基金National Key Research and Development Program of China(2022YFB2804401)。
文摘An in-pixel histogramming time-to-digital converter(hTDC)based on octonary search and 4-tap phase detection is presented,aiming to improve frame rate while ensuring high precicion.The proposed hTDC is a 12-bit two-step converter consisting of a 6-bit coarse quantization and a 6-bit fine quantization,which supports a time resolution of 120 ps and multiphoton counting up to 2 GHz without a GHz reference frequency.The proposed hTDC is designed in 0.11μm CMOS process with an area consumption of 6900μm^(2).The data from a behavioral-level model is imported into the designed hTDC circuit for simulation verification.The post-simulation results show that the proposed hTDC achieves 0.8%depth precision in 9 m range for short-range system design specifications and 0.2%depth precision in 48 m range for long-range system design specifications.Under 30×10^(3) lux background light conditions,the proposed hTDC can be used for SPAD-based flash LiDAR sensor to achieve a frame rate to 40 fps with 200 ps resolution in 9 m range.
基金supported by the National Natural Science Foundation of China(62071097)the Sichuan Science and Technology Program(2023NSFSC0458).
文摘In this paper,we study the orthogonal time frequency space signal transmission over multi-path channel in the presence of phase noise(PHN)at both sides of millimeter wave(mmWave)communication links.The statistics characteristics of the PHN-induced common phase error and inter-Doppler interference are investigated.Then,a column-shaped pilot structure is designed,and training pilots are used to realize linear-complexity PHN tracking and compensation.Numerical results demonstrate that the proposed scheme enables the signal to noise ratio loss to be restrained within 1 dB in contrast to the no PHN case.
基金Project(202203021221138)supported by the Collaborative Innovation Center for Shanxi Advanced Permanent Materials and Technologythe 1331 Engineering of Shanxi ProvinceFundamental Research Program of Shanxi Province,China。
文摘Al-doped manganese dioxide(MnO_(2))was synthesized by simple hydrothermal method,and a controllable phase transition of the MnO_(2)crystal phase fromβtoδwas achieved.The effects of Al doping concentration on the structure and electrochemical properties of electrode materials were studied in detail.The results show that the controlled synthesis requires a synergy between KMnO_(4),MnCl_(2)and AlCl_(3),and that Al^(3+)plays an important role.Compared with the pure phase MnO_(2),the crystallinity of Al-doped MnO_(2)decreases and the specific surface area increases,which provides more active sites for the electrode material.When 3 mmol Al^(3+)is added,the prepared MnO_(2)-3 has the largest specific capacitance and the highest rate performance.The energy density of the asymmetric supercapacitor(ASC)with MnO_(2)-3 as the positive electrode and activated carbon(AC)as the negative electrode can reach 18.4 W·h/kg at the power density of 400 W/kg,and the capacity can maintain 90%of the initial value after 20000 cycles,indicating that Al-doped MnO_(2)has certain practical application value.This study provides favorable guidance for MnO_(2)as a high performance electrode material.
基金Project(2023JH3/10200010)supported by the Excellent Youth Natural Science Foundation of Liaoning Province,ChinaProject(XLYC2203167)supported by the Liaoning Revitalization Talents Program,China+2 种基金Project(RC231175)supported by the Mid-career and Young Scientific and Technological Talents Program of Shenyang,ChinaProject(2023A03003-2)supported by the Key Special Program of Xinjiang,ChinaProject(N2301026)supported by the Fundamental Research Funds for the Central Universities,China。
文摘Nickel laterite ore is an important nickel-bearing mineral.Research on pre-heating and hydrogen pre-reduction in the pyrometallurgical process of nickel laterite ore is very limited,especially when using fluidized bed roasting.This study systematically explores the mechanisms of fluidized bed pre-heating treatment and hydrogen pre-reduction in the roasting process of saprolitic nickel laterite ore.According to single-factor experiment results,the appropriate pre-heating and pre-reduction conditions were a pre-heating temperature of 700℃,a pre-heating time of 30 min,a pre-reduction temperature of 700℃,a pre-reduction time of 30 min,and a hydrogen concentration of 80%.Then,the nickel metallization rate and iron metallization rate reached 90.56%and 41.31%,respectively.Various analytical and testing methods were employed to study the changes in phase composition,magnetism,surface element valence states,and microstructure of nickel laterite ore during fluidized pre-heating and pre-reduction.The study shows that hydrogen can achieve nickel reduction at relatively low temperatures.It was also found that pre-heating treatment of nickel laterite ore is beneficial.Pre-heating opens up the mineral structures of serpentine and limonite,allowing the reducing gas and nickel to interact quickly during the reduction process,enhancing the pre-reduction process.
基金Projects(2023AG05008,202302AB080012)supported by the Yunnan Major Scientific and Technological Program,ChinaProject(202405AC350015)supported by the Science and Technology Talent Programme of Yunnan Province,China。
文摘The phase transformation of galena in H_(2)SO_(4)-Fe_(2)(SO_(4))_(3) system under oxygen pressure was investigated.Results indicated that the critical conditions for the phase transformation of galena into lead jarosite(Pb-J)were 130℃,30 g/L H_(2)SO_(4),15 g/L Fe^(3+),and an oxygen partial pressure of 0.4 MPa.Furthermore,increased Fe^(3+)concentration and oxygen partial pressure did not enhance jarosite formation.Conversely,lowering the temperature and increasing the H_(2)SO_(4) concentration facilitated PbSO_(4) formation and inhibited its further conversion to Pb-J.Additionally,the effects of potassium sulfate,sodium sulfate,and high concentrations of zinc sulfate on the phase transformation of galena were examined through leaching tests,XRD,SEM-EDS,and FT-IR analyses.All three sulfates inhibited the conversion of galena to Pb-J.Among these,potassium sulfate prevented Pb-J formation and converted it more thoroughly into potassium jarosite.However,high concentrations of zinc sulfate facilitated the crystallization of both PbSO_(4) and Pb-J,which altered the morphology of the product.Zinc ions coprecipitated with Pb-J,thereby integrating into the product.
基金Project(2024YEE0109100) supported by the National Key R&D Program of ChinaProjects(52074131,52104373) supported by the National Natural Science Foundation of ChinaProjects(2022YFJH001,2024YFJH001) supported by the Science and Technology Plan Program of Qingyuan City,China。
文摘Trace amounts of Zr and V can increase the recrystallization temperature of Al-Mg-Si wrought aluminum alloys,which is expected to regulate the recrystallization grain.In this paper,trace amounts of V and Zr were added to recycled Al-Mg-Si alloys,and their e ffects on the microstructure and mechanical properties of the cast alloys were studied by scanning electron microscopy(SEM)and synchrotron radiation X-ray tomography(SRXT).The results show that the addition of Zr significantly increases the grain sizes due to the“Zr poisoning”;V addition has no significant effect on the grain size.The morphology of Fe-rich phase gradually changes from the large Chinese-script shape to the fine short rod and curved long strip shape,and the distribution uniformity is improved with the combined addition of V and Zr.The three-dimensional(3 D)morphology of Fe-rich phase includes granular,short rod-like,simple branch and multi-branch structures.The individual addition of V and Zr has no significant effect on the morphology of Fe-rich phase;but the combined addition of V and Zr significantly increases the number and volume fraction of Fe-rich phase with small size(diameter£15μm),the number of branches in the largest Fe-rich phase is significantly reduced,resulting in the improvement of elongation.This work provides a theoretical basis for the development of new recycled Al-Mg-Si alloys in industrial application.
基金the Presidential Foundation of CAEP(Grant No.YZJJZQ2023005)the National Natural Science Foundation of China(Grant No.22375191).
文摘Nowadays, ultrafine explosives are widely used in military fields. Ultrafine 2,2',4,4',6,6'-hexanitrostilbene(HNS) has emerged as an optimal primer for explosion foil initiators due to its excellent thermal stability and high-voltage short-pulse initiation performance. However, the solid phase ripening of ultrafine HNS leads to a degradation in its impact detonation performance. Previous studies have indicated that residual dimethyl formamide(DMF), which is present in ultrafine HNS prepared using the recrystallization method, affects ultrafine HNS ripening. The mechanism of residual solvent effects on solid phase ripening of ultrafine HNS is unclear. In this work, the specific surface area(SSA) derived from small angle X-ray scattering(SAXS) was utilized for kinetic fitting analysis to explore the mechanism by which residual solvents enhance the solid phase ripening of ultrafine HNS. The results of the SSA measured by insitu SAXS under conditions of 150℃ for 40 h revealed that the sample with 0.2% residual DMF exhibited a 21.51% decrease in SSA, whereas the sample with only 0.04% residual DMF showed a decrease of 15.66%.Furthermore, the higher amounts of residual DMF accelerated the reduction in SSA with time. Kinetic fitting analysis demonstrated that reducing residual DMF would lower both the activation energy and the pre-exponential factor, consequently decreasing the rate constant of solid phase ripening. The mechanism was speculated that it primarily facilitated the Ostwald ripening(OR). Additionally, contrast variation small angle X-ray scattering(CV-SAXS) confirmed that coating of ultrafine HNS particles is an effective method for inhibiting ripening, significantly reducing both the rate and extent of ripening of ultrafine HNS. This study predicts how residual solvents impact the solid phase ripening process of ultrafine HNS and proposes strategies for enhancing the long-term stability of ultrafine explosives.
基金Projects(62275275,11904239)supported by the National Natural Science Foundation of ChinaProjects(2021JJ40709,2022JJ20080)supported by the Natural Science Foundation of Hunan Province,China。
文摘Ultrathin 2D niobium oxide dichloride(NbOCl_(2))is an emerging member of the 2D ferroelectric material family with extensive potential to provide multifunctionality in electronic devices and nanophotonics elements.It exhibits negligible interlayer electronic coupling and significant excitonic behavior in the bulk state.Here we substantiate that NbOCl_(2) nanosheets can be exfoliated and effectively size-selected using controlled centrifugation techniques by the liquid phase exfoliation(LPE)method.Spectroscopic measurements displayed that the variations in dispersion were highly dependent on the nanosheet dimensions.The nanosheets seemed to be comparatively defect-free which will be further corroborated by high resolution transmission electron microscopy(HRTEM)and Raman analysis.The size selected nanosheets are unanticipated stable in isopropyl alcohol(IPA),possibly owing to the protective influence of a solvation shell.Additionally,the photothermal conversion response and photothermal stability of nanosized NbOCl_(2) were investigated.Our finding revealed that NbOCl_(2) possesses a robust photothermal agent property,boasting a photothermal conversion efficiency of more than 30%.This underscores its promising potential for various photothermal applications in different fields such as photothermal therapy and thermal energy conversion.
基金Project(2022YFC2905100)supported by the National Key Research and Development Program of ChinaProject(52174098)supported by the National Natural Science Foundation of China。
文摘With the continuous expansion of deep underground engineering and the growing demand for safety monitoring,microseismic monitoring has become a core method for early warning of rock mass fracture and engineering stability assessment.To address problems in existing methods,such as low data processing efficiency and poor phase recognition accuracy under low signal-to-noise ratio(SNR)conditions in complex geological environments,this study proposes an intelligent phase picking model based on ResUNet.The model integrates the residual learning mechanism of ResNet with the multi-scale feature extraction capability of UNet,effectively mitigating the vanishing gradient problem in deep networks.It also achieves cross-layer fusion of shallow detail features and deep semantic features through skip connections in the encoder-decoder structure.Compared with traditional short-time average/long-time average(STA/LTA)algorithms and advanced neural network models such as PhaseNet and EQTransformer,ResUNet shows superior performance in picking P-and S-wave phases.The model was trained on 400000 labeled microseismic signals from the Stanford earthquake dataset(STEAD)and was successfully applied to the Shizhuyuan polymetallic mine in Hunan Province,China.The results demonstrate that ResUNet achieves high picking accuracy and robustness in complex geological conditions,offering reliable technical support for early warning of disasters such as rockburst in deep underground engineering.
基金supported by the National Natural Science Foundation of China (62071144)
文摘Most of the existing direction of arrival(DOA)estimation algorithms are applied under the assumption that the array manifold is ideal.In practical engineering applications,the existence of non-ideal conditions such as mutual coupling between array elements,array amplitude and phase errors,and array element position errors leads to defects in the array manifold,which makes the performance of the algorithm decline rapidly or even fail.In order to solve the problem of DOA estimation in the presence of amplitude and phase errors and array element position errors,this paper introduces the first-order Taylor expansion equivalent model of the received signal under the uniform linear array from the Bayesian point of view.In the solution,the amplitude and phase error parameters and the array element position error parameters are regarded as random variables obeying the Gaussian distribution.At the same time,the expectation-maximization algorithm is used to update the probability distribution parameters,and then the two error parameters are solved alternately to obtain more accurate DOA estimation results.Finally,the effectiveness of the proposed algorithm is verified by simulation and experiment.
基金supported by the Youth Project of the Independent Subject of the State Key Laboratory of Explosion Science and Safety Protection,Beijing Institute of Technology(Grant Nos.QNKT25-13 and QNKT24-02)the 76th batch of Project funded by China Postdoctoral Science Foundation(Grant No.2024M764116)+3 种基金the National Natural Science Foundation of China(Grant Nos.12002048,12072037,12102050,and 12202067)the Science and Technology Commission,China(Grant No.2019-jcjc-zd-011-00)the Project supported by the Open Funds of Kui Yuan Laboratory(Grant No.KY202431)the State Key Laboratory of Explosion Science and Safety Protection(Grant No.KFJJ25-21M)。
文摘Simple cubic black phosphorus(BP)has been recognized as a strategic material due to its exceptional structural stability under extreme conditions.In this investigation,simple cubic BP was successfully synthesized through shock-induced phase transformation,utilizing amorphous red phosphorus as the precursor material.The phase evolution process was systematically investigated using plane shock loading apparatus,with shock pressure and temperature parameters being precisely controlled to optimize transformation kinetics.Comprehensive phase characterization revealed the correlation between thermodynamic loading profiles and cubic BP formation efficiency.Precursor modification strategies were implemented through orthorhombic BP utilization,resulting in enhanced cubic phase yield and crystallinity.The synthesized cubic BP variants are considered promising candidates for advanced protective material systems,particularly where combinations of mechanical resilience and thermal stability are required under extreme operational conditions.This research provides critical insights into shock-induced phase transformation mechanics,while establishing foundational protocols for manufacturing non-equilibrium materials with potential applications in next-generation defensive technologies.
文摘In the field of deep space exploration,the rapid development of terahertz spectrometer has put forward higher requirements to the back-end chirp transform spectrometer(CTS)system.In order to simultaneously meet the measurement requirements of wide bandwidth and high accuracy spectral lines,we built a CTS system with an analysis bandwidth of 1 GHz and a frequency resolution of 100 kHz around the surface acoustic wave(SAW)chirp filter with a bandwidth of 1 GHz.In this paper,the relationship between the CTS nonlinear phase error shift model and the basic measurement parameters is studied,and the effect of CTS phase mismatch on the pulse compression waveform is analyzed by simulation.And the expander error optimization method is proposed for the problem that the large nonlinear error of the expander leads to the unbalanced response of the CTS system and the serious distortion of the compressed pulse waveform under large bandwidth.It is verified through simulation and experiment that the method is effective for reducing the root mean square error(RMSE)of the phase of the expander from 18.75°to 6.65°,reducing the in-band standard deviation of the CTS frequency resolution index from 8.43 kHz to 4.72 kHz,solving the problem of serious distortion of the compressed pulse waveform,and improving the uneven CTS response under large bandwidth.
基金The project was supported by the National Key R&D Program of China(2021YFF0500702)Natural Science Foundation of Shanghai(22JC1404200)+3 种基金Program of Shanghai Academic/Technology Research Leader(20XD1404000)Natural Science Foundation of China(U22B20136,22293023)Science and Technology Major Project of Inner Mongolia(2021ZD0042)the Youth Innovation Promotion Association of CAS。
文摘Ni/TiO_(2) catalyst is widely employed for photo-driven DRM reaction while the influence of crystal structure of TiO_(2) remains unclear.In this work,the rutile/anatase ratio in supports was successfully controlled by varying the calcination temperature of anatase-TiO_(2).Structural characterizations revealed that a distinct TiO_(x) coating on the Ni nanoparticles(NPs)was evident for Ni/TiO_(2)-700 catalyst due to strong metal-support interaction.It is observed that the TiOx overlayer gradually disappeared as the ratio of rutile/anatase increased,thereby enhancing the exposure of Ni active sites.The exposed Ni sites enhanced visible light absorption and boosted the dissociation capability of CH4,which led to the much elevated catalytic activity for Ni/TiO_(2)-950 in which rutile dominated.Therefore,the catalytic activity of solar-driven DRM reaction was significantly influenced by the rutile/anatase ratio.Ni/TiO_(2)-950,characterized by a predominant rutile phase,exhibited the highest DRM reactivity,with remarkable H_(2) and CO production rates reaching as high as 87.4 and 220.2 mmol/(g·h),respectively.These rates were approximately 257 and 130 times higher,respectively,compared to those obtained on Ni/TiO_(2)-700 with anatase.This study suggests that the optimization of crystal structure of TiO_(2) support can effectively enhance the performance of photothermal DRM reaction.
