In order to study the propagation mechanism of continuous rotating detonation wave,the H2/air continuous rotating detonation engine ignited by tangentially installed H2/O2pre-detonation tube is studied experimentally ...In order to study the propagation mechanism of continuous rotating detonation wave,the H2/air continuous rotating detonation engine ignited by tangentially installed H2/O2pre-detonation tube is studied experimentally using a tilt slot injector structure.The experimental results show that the stable rotating detonation wave can be gained successfully with the equivalent ratio of 0.93.The propagation frequency and velocity of rotating detonation wave range from 5200 to 5500 Hz and from 1518.5 to 1606.1 m/s,respectively.Three propagation modes,such as rotation,reversal and bifurcation,of detonation wave are verified through the analysis of propagation mechanism of rotating detonation wave.展开更多
In order to study the instability propagation characteristics of the liquid kerosene rotating detonation wave(RDW),a series of experimental tests were carried out on the rotating detonation combustor(RDC)with air-heat...In order to study the instability propagation characteristics of the liquid kerosene rotating detonation wave(RDW),a series of experimental tests were carried out on the rotating detonation combustor(RDC)with air-heater.The fuel and oxidizer are room-temperature liquid kerosene and preheated oxygenenriched air,respectively.The experimental tests keep the equivalence ratio of 0.81 and the oxygen mass fraction of 35%unchanged,and the total mass flow rate is maintained at about 1000 g/s,changing the total temperature of the oxygen-enriched air from 620 K to 860 K.Three different types of instability were observed in the experiments:temporal and spatial instability,mode transition and re-initiation.The interaction between RDW and supply plenum may be the main reason for the fluctuations of detonation wave velocity and pressure peaks with time.Moreover,the inconsistent mixing of fuel and oxidizer at different circumferential positions is related to RDW oscillate spatially.The phenomenon of single-double-single wave transition is analyzed.During the transition,the initial RDW weakens until disappears,and the compression wave strengthens until it becomes a new RDWand propagates steadily.The increased deflagration between the detonation products and the fresh gas layer caused by excessively high temperature is one of the reasons for the RDC quenching and re-initiation.展开更多
In this paper,the kerosene/air rotating detonation engines(RDE)are numerically investigated,and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE inc...In this paper,the kerosene/air rotating detonation engines(RDE)are numerically investigated,and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation,instabilities,and propulsive performance.A hybrid MPI t OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC)systems.A series of cases with the total pressure of 1 MPa,1.5 MPa,2 MPa,and the equivalence ratio of 0.9,1,1.4 are simulated.On one hand,the total pressure shows a significant impact on the instabilities of rotating detonation waves.The instability phenomenon is observed in cases with low total pressure(1 MPa)and weakened with the increase of the total pressure.The total pressure has a small impact on the detonation wave velocity and the specific impulse.On the other hand,the equivalence ratio shows a negligible influence on the instabilities,while it affects the ignition process and accounts for the detonation velocity deficit.It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition.Little difference was observed in the thrust with different equivalence ratios of 0.9,1,and 1.4.The highest specific impulse was obtained in the lean fuel cases,which is around 2700 s.The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.展开更多
Due to the pressure gain combustion characteristics,the rotating detonation combustor(RDC)can enhance thermodynamic cycle efficiency.Therefore,the performance of gas-turbine engine can be further improved with this co...Due to the pressure gain combustion characteristics,the rotating detonation combustor(RDC)can enhance thermodynamic cycle efficiency.Therefore,the performance of gas-turbine engine can be further improved with this combustion technology.In the present study,the RDC operation performance with a turbine guide vane(TGV)is experimentally investigated.Hydrogen and air are used as propellants while hydrogen and air mass flow rate are about 16.1 g/s and 500 g/s and the equivalence ratio is about 1.0.A pre-detonator is used to ignite the mixture.High-frequency dynamic pressure transducers and silicon pressure sensors are employed to measure pressure oscillations and static pressure in the combustion chamber.The experimental results show that the steady propagation of rotating detonation wave(RDW)is observed in the combustion chamber and the mean propagation velocity is above 1650 m/s,reaching over 84%of theoretical Chapman-Jouguet detonation velocity.Clockwise and counterclockwise propagation directions of RDW are obtained.For clockwise propagation direction,the static pressure is about 15%higher in the combustor compared with counterclockwise propagation direction,but the RDW dominant frequency is lower.When the oblique shock wave propagates across the TGV,the pressure oscillations reduces significantly.In addition,as the detonation products flow through the TGV,the static pressure drops up to 32%and 43%for clockwise and counterclockwise propagation process respectively.展开更多
Due to the inherent working mode of rotating detonation engine(RDE),the detonation flow field has the characteristics of pressure oscillation and axial kinetic energy loss,which makes it difficult to design nozzle and...Due to the inherent working mode of rotating detonation engine(RDE),the detonation flow field has the characteristics of pressure oscillation and axial kinetic energy loss,which makes it difficult to design nozzle and improve propulsion performance.Therefore,in order to improve the characteristics of detonation flow field,the three-dimensional numerical simulation of annular chamber and hollow chamber is carried out with premixed hydrogen/air as fuel in this paper,and then tries to combine the two chambers to weaken the oscillation characteristics of detonation flow field through the interaction of detonation flow field,which is a new method to regulate the detonation flow field.The results show that there are four states of velocity vectors at the outlet of annular chamber and hollow chamber,which makes RDE be affected by rolling moment and results in the loss of axial kinetic energy.In the external flow field of combined chamber,the phenomenon of cyclic reflection of expansion wave and compression wave on the free boundary is observed,which results in Mach disk structure.Moreover,the pressure monitoring points are set at the external flow field.The pressure signal shows that the high-frequency pressure oscillation at the external flow field of the combined chamber has been greatly weakened.Compared to the annular chamber,the relative standard deviation(RSD) has been reduced from 14.6% to5.6%.The results thus demonstrate that this method is feasible to adjust the pressure oscillation characteristics of the detonation flow field,and is of great significance to promote the potential of RDE and nozzle design.展开更多
Generally, a magnetic target can be described with six parameters, three describing the position and three describing the magnetic moment. Due to a lack of sufficient components from one magnetometer, we need more tha...Generally, a magnetic target can be described with six parameters, three describing the position and three describing the magnetic moment. Due to a lack of sufficient components from one magnetometer, we need more than one magnetometer when locating the magnetic target. Thus, a magnetometer array should be designed. The baseline of the array is an important factor that affects the localization accuracy of the target. In this paper, we focus on the localization of a static target by using a scalar magnetometer array. We present the scalar magnetometer array with a cross-shaped structure.We propose a method of determining the optimal baseline according to the parameters of the magnetometer and detection requirements. In the method, we use the traditional signal-to-noise ratio（SNR） as a performance index, and obtain the optimal baseline of the array by using the Monte Carlo method. The proposed method of determining the optimal baseline is verified in simulation. The arrays with different baselines are used to locate a static magnetic target. The results show that the location performance is better when using the array with the optimal baseline determined by the proposed method.展开更多
A low hole injection efficiency for InGaN/GaN micro-light-emitting diodes(μLEDs) has become one of the main bottlenecks affecting the improvement of the external quantum efficiency(EQE) and the optical power. In this...A low hole injection efficiency for InGaN/GaN micro-light-emitting diodes(μLEDs) has become one of the main bottlenecks affecting the improvement of the external quantum efficiency(EQE) and the optical power. In this work, we propose and fabricate a polarization mismatched p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure for 445 nm GaN-based μLEDs with the size of 40 × 40 μm^(2), which serves as the hole injection layer. The polarization-induced electric field in the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure provides holes with more energy and can facilitate the non-equilibrium holes to transport into the active region for radiative recombination. Meanwhile, a secondary etched mesa for μLEDs is also designed, which can effectively keep the holes apart from the defected region of the mesa sidewalls, and the surface nonradiative recombination can be suppressed. Therefore, the proposed μLED with the secondary etched mesa and the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure has the enhanced EQE and the improved optical power density when compared with the μLED without such designs.展开更多
基金sponsored by National Defence Researching Fund(9140c300202120c30)the Fundamental Research Fund for the central Universities(30920130112007)
文摘In order to study the propagation mechanism of continuous rotating detonation wave,the H2/air continuous rotating detonation engine ignited by tangentially installed H2/O2pre-detonation tube is studied experimentally using a tilt slot injector structure.The experimental results show that the stable rotating detonation wave can be gained successfully with the equivalent ratio of 0.93.The propagation frequency and velocity of rotating detonation wave range from 5200 to 5500 Hz and from 1518.5 to 1606.1 m/s,respectively.Three propagation modes,such as rotation,reversal and bifurcation,of detonation wave are verified through the analysis of propagation mechanism of rotating detonation wave.
基金supported by the National Natural Science Foundation of China(Grant No.11802137,11702143 and 11802039)the Fundamental Research Funds for the Central Universities(No.30919011259).
文摘In order to study the instability propagation characteristics of the liquid kerosene rotating detonation wave(RDW),a series of experimental tests were carried out on the rotating detonation combustor(RDC)with air-heater.The fuel and oxidizer are room-temperature liquid kerosene and preheated oxygenenriched air,respectively.The experimental tests keep the equivalence ratio of 0.81 and the oxygen mass fraction of 35%unchanged,and the total mass flow rate is maintained at about 1000 g/s,changing the total temperature of the oxygen-enriched air from 620 K to 860 K.Three different types of instability were observed in the experiments:temporal and spatial instability,mode transition and re-initiation.The interaction between RDW and supply plenum may be the main reason for the fluctuations of detonation wave velocity and pressure peaks with time.Moreover,the inconsistent mixing of fuel and oxidizer at different circumferential positions is related to RDW oscillate spatially.The phenomenon of single-double-single wave transition is analyzed.During the transition,the initial RDW weakens until disappears,and the compression wave strengthens until it becomes a new RDWand propagates steadily.The increased deflagration between the detonation products and the fresh gas layer caused by excessively high temperature is one of the reasons for the RDC quenching and re-initiation.
基金The authors would like to acknowledge the National Natural Science Foundation of China(Grant Nos.11802137,11702143)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYCX19_0292)+1 种基金the Natural Science Foundation for Young Scientists of Jiangsu Province of China(Grant No.BK20190468)the Fundamental Research Funds for the Central Universities(Grant Nos.30918011343,30919011259,309190112A1).
文摘In this paper,the kerosene/air rotating detonation engines(RDE)are numerically investigated,and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation,instabilities,and propulsive performance.A hybrid MPI t OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC)systems.A series of cases with the total pressure of 1 MPa,1.5 MPa,2 MPa,and the equivalence ratio of 0.9,1,1.4 are simulated.On one hand,the total pressure shows a significant impact on the instabilities of rotating detonation waves.The instability phenomenon is observed in cases with low total pressure(1 MPa)and weakened with the increase of the total pressure.The total pressure has a small impact on the detonation wave velocity and the specific impulse.On the other hand,the equivalence ratio shows a negligible influence on the instabilities,while it affects the ignition process and accounts for the detonation velocity deficit.It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition.Little difference was observed in the thrust with different equivalence ratios of 0.9,1,and 1.4.The highest specific impulse was obtained in the lean fuel cases,which is around 2700 s.The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.
基金the National Natural Science Foundation of China(No.11702143 and 11802137)the Fundamental Research Funds for the Central Universities(No.30918011343 and 30919011259).
文摘Due to the pressure gain combustion characteristics,the rotating detonation combustor(RDC)can enhance thermodynamic cycle efficiency.Therefore,the performance of gas-turbine engine can be further improved with this combustion technology.In the present study,the RDC operation performance with a turbine guide vane(TGV)is experimentally investigated.Hydrogen and air are used as propellants while hydrogen and air mass flow rate are about 16.1 g/s and 500 g/s and the equivalence ratio is about 1.0.A pre-detonator is used to ignite the mixture.High-frequency dynamic pressure transducers and silicon pressure sensors are employed to measure pressure oscillations and static pressure in the combustion chamber.The experimental results show that the steady propagation of rotating detonation wave(RDW)is observed in the combustion chamber and the mean propagation velocity is above 1650 m/s,reaching over 84%of theoretical Chapman-Jouguet detonation velocity.Clockwise and counterclockwise propagation directions of RDW are obtained.For clockwise propagation direction,the static pressure is about 15%higher in the combustor compared with counterclockwise propagation direction,but the RDW dominant frequency is lower.When the oblique shock wave propagates across the TGV,the pressure oscillations reduces significantly.In addition,as the detonation products flow through the TGV,the static pressure drops up to 32%and 43%for clockwise and counterclockwise propagation process respectively.
文摘Due to the inherent working mode of rotating detonation engine(RDE),the detonation flow field has the characteristics of pressure oscillation and axial kinetic energy loss,which makes it difficult to design nozzle and improve propulsion performance.Therefore,in order to improve the characteristics of detonation flow field,the three-dimensional numerical simulation of annular chamber and hollow chamber is carried out with premixed hydrogen/air as fuel in this paper,and then tries to combine the two chambers to weaken the oscillation characteristics of detonation flow field through the interaction of detonation flow field,which is a new method to regulate the detonation flow field.The results show that there are four states of velocity vectors at the outlet of annular chamber and hollow chamber,which makes RDE be affected by rolling moment and results in the loss of axial kinetic energy.In the external flow field of combined chamber,the phenomenon of cyclic reflection of expansion wave and compression wave on the free boundary is observed,which results in Mach disk structure.Moreover,the pressure monitoring points are set at the external flow field.The pressure signal shows that the high-frequency pressure oscillation at the external flow field of the combined chamber has been greatly weakened.Compared to the annular chamber,the relative standard deviation(RSD) has been reduced from 14.6% to5.6%.The results thus demonstrate that this method is feasible to adjust the pressure oscillation characteristics of the detonation flow field,and is of great significance to promote the potential of RDE and nozzle design.
基金supported by the National Natural Science Foundation of China(Grant No.61174192)
文摘Generally, a magnetic target can be described with six parameters, three describing the position and three describing the magnetic moment. Due to a lack of sufficient components from one magnetometer, we need more than one magnetometer when locating the magnetic target. Thus, a magnetometer array should be designed. The baseline of the array is an important factor that affects the localization accuracy of the target. In this paper, we focus on the localization of a static target by using a scalar magnetometer array. We present the scalar magnetometer array with a cross-shaped structure.We propose a method of determining the optimal baseline according to the parameters of the magnetometer and detection requirements. In the method, we use the traditional signal-to-noise ratio（SNR） as a performance index, and obtain the optimal baseline of the array by using the Monte Carlo method. The proposed method of determining the optimal baseline is verified in simulation. The arrays with different baselines are used to locate a static magnetic target. The results show that the location performance is better when using the array with the optimal baseline determined by the proposed method.
基金supported in part by the National Natural Science Foundation of China (Grant Nos.62074050 and 61975051)Research Fund by State Key Laboratory of Reliability and Intelligence of Electrical Equipment,Hebei University of Technology (Grant Nos.EERI PI2020008 and EERI_PD2021012)Joint Research Project for Tunghsu Group and Hebei University of Technology (Grant No.HI1909)。
文摘A low hole injection efficiency for InGaN/GaN micro-light-emitting diodes(μLEDs) has become one of the main bottlenecks affecting the improvement of the external quantum efficiency(EQE) and the optical power. In this work, we propose and fabricate a polarization mismatched p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure for 445 nm GaN-based μLEDs with the size of 40 × 40 μm^(2), which serves as the hole injection layer. The polarization-induced electric field in the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure provides holes with more energy and can facilitate the non-equilibrium holes to transport into the active region for radiative recombination. Meanwhile, a secondary etched mesa for μLEDs is also designed, which can effectively keep the holes apart from the defected region of the mesa sidewalls, and the surface nonradiative recombination can be suppressed. Therefore, the proposed μLED with the secondary etched mesa and the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure has the enhanced EQE and the improved optical power density when compared with the μLED without such designs.
