While pre-deformation is often conducted before aging treatment to increase the strength and microhardness of 2195 Al-Li alloy, it often increases the fatigue crack growth(FCG) rate and thus reduces the fatigue life o...While pre-deformation is often conducted before aging treatment to increase the strength and microhardness of 2195 Al-Li alloy, it often increases the fatigue crack growth(FCG) rate and thus reduces the fatigue life of the alloy.To determine the effects and causes of pre-deformation and heat treatment on the mechanical properties and FCG rate of2195 Al-Li alloy, and to provide a suitable calculation model for the FCG rate under different pre-deformation conditions, 2195 Al-Li alloy specimens with different degrees of pre-rolling(0, 3%, 6%, and 9%) were investigated. The experimental results indicate that with the increase of pre-rolling, the density of the T1phase and the uniformity of the S′distribution and the microhardness, tensile strength, and yield strength of the alloy increase and at the same time the FCG rate increases, and thus the fatigue life is reduced. It was also found that the normalized stress intensity factor of elastic modulus(E) can be applied to correlate the FCG rate of pre-rolled 2195 Al-Li alloy with constant C and K parameters.展开更多
The key parameters of the adhesive layer of a reinforcing patch are of great significance and affect the ability to suppress crack propagation in an Al–Li alloy patch-reinforced structure.This paper proposes a method...The key parameters of the adhesive layer of a reinforcing patch are of great significance and affect the ability to suppress crack propagation in an Al–Li alloy patch-reinforced structure.This paper proposes a method to determine the key parameters of the adhesive layer of adhesively bonded joints in the Al–Li alloy patch-reinforced structure.A zero-thickness cohesive zone model(CZM)was selected to simulate the adhesive layer’s fracture process,and an orthogonal simulation was designed to compare against the test results.A three-dimensional progressive damage model of an Al–Li alloy patch-reinforced structure with single-lap adhesively bonded joints was developed.The simulation’s results closely agree with the test results,demonstrating that this method of determining the key parameters is likely accurate.The results also verify the correctness of the cohesive strength and fracture energy,the two key parameters of the cohesive zone model.The model can accurately predict the strength and fracture process of adhesively bonded joints,and can be used in research to suppress crack propagation in Al–Li alloy patch-reinforced structures.展开更多
There have been a great demand for a suitable and convenient method in the field of buckling analysis of stiffened ship structures, which is essential to structural safety assessment and is significantly time-consumin...There have been a great demand for a suitable and convenient method in the field of buckling analysis of stiffened ship structures, which is essential to structural safety assessment and is significantly time-consuming. Modeling, buckling behaviors and ultimate strength prediction of stiffened panels were investigated. The modeling specification including nonlinear finite element model and imperfections generation, and post-buckling analysis procedure of stiffened plates were demonstrated. And a software tool using set-based finite element method was developed and executed in the MSC. Marc environment. Different types of stiffen panels of marine structures have been employed to investigate the buckling behavior and assess the validity in the estimation of ultimate strength. A comparison between results of the generally accepted methods, experiments and the software tool developed was demonstrated. It is shown that the software tool can predict the ultimate capacity of stiffened panels with imperfections with a good accuracy.展开更多
分布异构计算资源通过网络连接形成算力网络(Computing power network,CPN),其以“连”和“算”为核心.针对广分布异构性导致可行解空间巨大、强不确定性导致可行解空间易变、高约束复杂性导致可行解孤岛繁多、多目标性导致冲突目标权...分布异构计算资源通过网络连接形成算力网络(Computing power network,CPN),其以“连”和“算”为核心.针对广分布异构性导致可行解空间巨大、强不确定性导致可行解空间易变、高约束复杂性导致可行解孤岛繁多、多目标性导致冲突目标权衡优化难等挑战,提出一个多层次算力网络体系框架,包括参数化结构化业务管理、三阶段(计划、调度、执行)闭环调度模式、多模态资源管理三个功能.提出支持快速、高效、鲁棒的“算法+知识+数据+算力”的算力网络智慧调度框架,形式化分析可行解空间,解析调度策略关键参数,定性分析调度算法性能与效率的内在关系,详细综述调度算法类型,综述算力网络调度研究进展与发展方向.对比已有相关综述研究,展望算力网络调度未来理论和技术的难点与趋势.展开更多
基金Project(U21A20132) supported by the National Natural Science Foundation of ChinaProject(Gui Renzi2019(13))supported by the Guangxi Specially-invited Experts Foundation of Guangxi Zhuang Autonomous Region,China。
文摘While pre-deformation is often conducted before aging treatment to increase the strength and microhardness of 2195 Al-Li alloy, it often increases the fatigue crack growth(FCG) rate and thus reduces the fatigue life of the alloy.To determine the effects and causes of pre-deformation and heat treatment on the mechanical properties and FCG rate of2195 Al-Li alloy, and to provide a suitable calculation model for the FCG rate under different pre-deformation conditions, 2195 Al-Li alloy specimens with different degrees of pre-rolling(0, 3%, 6%, and 9%) were investigated. The experimental results indicate that with the increase of pre-rolling, the density of the T1phase and the uniformity of the S′distribution and the microhardness, tensile strength, and yield strength of the alloy increase and at the same time the FCG rate increases, and thus the fatigue life is reduced. It was also found that the normalized stress intensity factor of elastic modulus(E) can be applied to correlate the FCG rate of pre-rolled 2195 Al-Li alloy with constant C and K parameters.
基金Project(51575535)supported by the National Natural Science Foundation of ChinaProject(2015CX002)supported by the Innovation-driven Plan in Central South University,China+2 种基金Project(zzyjkt2013-09B)supported by the Fund of the State Key Laboratory of High Performance Manufacturing,ChinaProject(2017zzts638)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2016RS2015)supported by the Scientific and Technological Leading Talent Projects of Hunan Province,China
文摘The key parameters of the adhesive layer of a reinforcing patch are of great significance and affect the ability to suppress crack propagation in an Al–Li alloy patch-reinforced structure.This paper proposes a method to determine the key parameters of the adhesive layer of adhesively bonded joints in the Al–Li alloy patch-reinforced structure.A zero-thickness cohesive zone model(CZM)was selected to simulate the adhesive layer’s fracture process,and an orthogonal simulation was designed to compare against the test results.A three-dimensional progressive damage model of an Al–Li alloy patch-reinforced structure with single-lap adhesively bonded joints was developed.The simulation’s results closely agree with the test results,demonstrating that this method of determining the key parameters is likely accurate.The results also verify the correctness of the cohesive strength and fracture energy,the two key parameters of the cohesive zone model.The model can accurately predict the strength and fracture process of adhesively bonded joints,and can be used in research to suppress crack propagation in Al–Li alloy patch-reinforced structures.
基金Projects(51575535,51805551)supported by the National Natural Science Foundation of ChinaProject(ZZYJKT2018-15)supported by the of State Key Laboratory of High Performance Complex Manufacturing,China+1 种基金Project(2015CX002)supported by the Innovation-driven Plan in Central South University,ChinaProject(2018BB30501)supported by the Key R&D Program of Liuzhou City,China
文摘There have been a great demand for a suitable and convenient method in the field of buckling analysis of stiffened ship structures, which is essential to structural safety assessment and is significantly time-consuming. Modeling, buckling behaviors and ultimate strength prediction of stiffened panels were investigated. The modeling specification including nonlinear finite element model and imperfections generation, and post-buckling analysis procedure of stiffened plates were demonstrated. And a software tool using set-based finite element method was developed and executed in the MSC. Marc environment. Different types of stiffen panels of marine structures have been employed to investigate the buckling behavior and assess the validity in the estimation of ultimate strength. A comparison between results of the generally accepted methods, experiments and the software tool developed was demonstrated. It is shown that the software tool can predict the ultimate capacity of stiffened panels with imperfections with a good accuracy.
文摘分布异构计算资源通过网络连接形成算力网络(Computing power network,CPN),其以“连”和“算”为核心.针对广分布异构性导致可行解空间巨大、强不确定性导致可行解空间易变、高约束复杂性导致可行解孤岛繁多、多目标性导致冲突目标权衡优化难等挑战,提出一个多层次算力网络体系框架,包括参数化结构化业务管理、三阶段(计划、调度、执行)闭环调度模式、多模态资源管理三个功能.提出支持快速、高效、鲁棒的“算法+知识+数据+算力”的算力网络智慧调度框架,形式化分析可行解空间,解析调度策略关键参数,定性分析调度算法性能与效率的内在关系,详细综述调度算法类型,综述算力网络调度研究进展与发展方向.对比已有相关综述研究,展望算力网络调度未来理论和技术的难点与趋势.
