A two-pass annealing/quenching internal spinning process with small-end rotations is proposed to form a curved generatrix conical thin-walled shell.That is,annealing at 360°C for 2 h followed by the 1st pass spin...A two-pass annealing/quenching internal spinning process with small-end rotations is proposed to form a curved generatrix conical thin-walled shell.That is,annealing at 360°C for 2 h followed by the 1st pass spinning,and finally quenching in ice water after holding for 1 h at 498°C followed by the 2nd pass spinning.ABAQUS finite element software is used to simulate the internal spinning process of the products formed under different forming parameters.The distribution laws of spinning force,the stress and strain under different forming processes were compared and analyzed.The mechanical properties and microstructure of the products are subsequently analyzed.The results show that the strain and the residual stress in the skin area of the formed products under two-pass spinning process more uniform,and the hardness and the mechanical performance are improved.The microstructure of the products formed with the 0.15 mm thickness reduction at the 2nd pass is excellent.And the second phase grain size distributed uniformly in the range of 36μm.Whereas,the second phase particles are broken seriously and the size distribution inhomogeneity is increased when the thickness reduction in the skin area is greater than 0.20 mm at the 2nd pass spinning process.展开更多
Based on the traditional hydraulic bulging process,an improved hydraulic bulging process with axial feeding in the bulging process was proposed.The finite element simulation and experiment of bellows formed by the tra...Based on the traditional hydraulic bulging process,an improved hydraulic bulging process with axial feeding in the bulging process was proposed.The finite element simulation and experiment of bellows formed by the traditional and improved hydraulic bulging processes were conducted.The grid strain measurement system analysis results of strain and wall thickness distribution of the metal bellows,obtained from simulation and experiment,show that the maximum thinning rates of the wall thickness under the traditional and improved processes were 15%and 10%,respectively.And the wall thickness distribution of the metal bellows formed with improved process was more uniform.The strain values from the root to crown of the waveform increased gradually.However,the strain values were smaller than those of traditional process due to the axial feeding of the improved process in bulging process.展开更多
基金Project(51775479)supported by the National Natural Science Foundation of ChinaProject(E2017203046)supported by the Natural Science Foundation of Hebei Province,China
文摘A two-pass annealing/quenching internal spinning process with small-end rotations is proposed to form a curved generatrix conical thin-walled shell.That is,annealing at 360°C for 2 h followed by the 1st pass spinning,and finally quenching in ice water after holding for 1 h at 498°C followed by the 2nd pass spinning.ABAQUS finite element software is used to simulate the internal spinning process of the products formed under different forming parameters.The distribution laws of spinning force,the stress and strain under different forming processes were compared and analyzed.The mechanical properties and microstructure of the products are subsequently analyzed.The results show that the strain and the residual stress in the skin area of the formed products under two-pass spinning process more uniform,and the hardness and the mechanical performance are improved.The microstructure of the products formed with the 0.15 mm thickness reduction at the 2nd pass is excellent.And the second phase grain size distributed uniformly in the range of 36μm.Whereas,the second phase particles are broken seriously and the size distribution inhomogeneity is increased when the thickness reduction in the skin area is greater than 0.20 mm at the 2nd pass spinning process.
基金Project (51775479) supported by the National Natural Science Foundation of ChinaProject (E2017203046) supported by the Natural Science Foundation of Hebei Province,China
文摘Based on the traditional hydraulic bulging process,an improved hydraulic bulging process with axial feeding in the bulging process was proposed.The finite element simulation and experiment of bellows formed by the traditional and improved hydraulic bulging processes were conducted.The grid strain measurement system analysis results of strain and wall thickness distribution of the metal bellows,obtained from simulation and experiment,show that the maximum thinning rates of the wall thickness under the traditional and improved processes were 15%and 10%,respectively.And the wall thickness distribution of the metal bellows formed with improved process was more uniform.The strain values from the root to crown of the waveform increased gradually.However,the strain values were smaller than those of traditional process due to the axial feeding of the improved process in bulging process.
