Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al wit...Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.展开更多
A deep understanding of explosive sensitivities and their factors is important for safe and reliable applications.However,quantitative prediction of the sensitivities is difficult.Here,reactive molecular dynamics simu...A deep understanding of explosive sensitivities and their factors is important for safe and reliable applications.However,quantitative prediction of the sensitivities is difficult.Here,reactive molecular dynamics simulation models for high-speed piston impacts on explosive supercells were established.Simulations were also performed to investigate shock-induced reactions of various high-energy explosives.The fraction of reacted explosive molecules in an initial supercell changed linearly with the propagation distance of the shock-wave front.The corresponding slope could be used as a reaction rate for a specific shock-loading velocity.Reaction rates that varied with the shock-loading pressure exhibited two-stage linearities with different slopes.The two inflection points corresponded to the initial and accelerated reactions,which respectively correlated to the thresholds of shock-induced ignition and detonation.Therefore,the ignition and detonation critical pressures could be determined.The sensitivity could then be a quantitative prediction of the critical pressure.The accuracies of the quantitative shock sensitivity predictions were verified by comparing the impact and shock sensitivities of common explosives and the characteristics of anisotropic shock-induced reactions.Molecular dynamics simulations quantitatively predict and rank shock sensitivities by using only crystal structures of the explosives.Overall,this method will enable the design and safe use of explosives.展开更多
Impact flash occurs when objects collide at supersonic speeds and can be used for real-time damage assessment when weapons rely on kinetic energy to destroy targets.However,the mechanism of impact flash remains unclea...Impact flash occurs when objects collide at supersonic speeds and can be used for real-time damage assessment when weapons rely on kinetic energy to destroy targets.However,the mechanism of impact flash remains unclear.A series of impact flash experiments of flat-head long-rod projectiles impacting thin target plates were performed with a two-stage light gas gun.The impact flash spectra for 6061 aluminum at 1.3e3.2 km/s collision speeds were recorded with a high-speed camera,a photoelectric sensor,and a time-resolved spectrometer.The intensity of the impact flash exhibited a pulse characteristic with time.The intensity(I)increased with impact velocity(V0)according to IfVn 0,where n?4.41 for V0>2 km/s.However,for V0<2 km/s,n?2.21,and the intense flash duration is an order of magnitude less than that of higher V0.When V0>2 km/s,a continuous spectrum(thermal radiation background)was observed and increased in intensity with V0.However,for V0<2 km/s,only atomic line spectra were detected.There was no aluminum spectral lines for V0<2 km/s,which indicated that it had not been vaporized.The initial intense flash was emission from excited and ionized ambient gases near the impact surface,and had little relationship with shock temperature rise,indicating a new mechanism of impact flash.展开更多
基金The authors would like to acknowledge National Natural Science Foundation of China(Grant No.11832006)Open Project of State Key Laboratory of Explosion Science and Technology in Beijing Institute of Technology(Grant No.KFJJ20-04 M)to provide fund for conducting experiments.
文摘Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.
基金supported by the National Natural Science Foundation of China(Grant No.11832006).
文摘A deep understanding of explosive sensitivities and their factors is important for safe and reliable applications.However,quantitative prediction of the sensitivities is difficult.Here,reactive molecular dynamics simulation models for high-speed piston impacts on explosive supercells were established.Simulations were also performed to investigate shock-induced reactions of various high-energy explosives.The fraction of reacted explosive molecules in an initial supercell changed linearly with the propagation distance of the shock-wave front.The corresponding slope could be used as a reaction rate for a specific shock-loading velocity.Reaction rates that varied with the shock-loading pressure exhibited two-stage linearities with different slopes.The two inflection points corresponded to the initial and accelerated reactions,which respectively correlated to the thresholds of shock-induced ignition and detonation.Therefore,the ignition and detonation critical pressures could be determined.The sensitivity could then be a quantitative prediction of the critical pressure.The accuracies of the quantitative shock sensitivity predictions were verified by comparing the impact and shock sensitivities of common explosives and the characteristics of anisotropic shock-induced reactions.Molecular dynamics simulations quantitatively predict and rank shock sensitivities by using only crystal structures of the explosives.Overall,this method will enable the design and safe use of explosives.
基金This work was supported by the National Key R&D Programof China(Grant No.2016YFC0801204)the National Programon Key Basic Research Project of China(973 Program,Grant No.613312).
文摘Impact flash occurs when objects collide at supersonic speeds and can be used for real-time damage assessment when weapons rely on kinetic energy to destroy targets.However,the mechanism of impact flash remains unclear.A series of impact flash experiments of flat-head long-rod projectiles impacting thin target plates were performed with a two-stage light gas gun.The impact flash spectra for 6061 aluminum at 1.3e3.2 km/s collision speeds were recorded with a high-speed camera,a photoelectric sensor,and a time-resolved spectrometer.The intensity of the impact flash exhibited a pulse characteristic with time.The intensity(I)increased with impact velocity(V0)according to IfVn 0,where n?4.41 for V0>2 km/s.However,for V0<2 km/s,n?2.21,and the intense flash duration is an order of magnitude less than that of higher V0.When V0>2 km/s,a continuous spectrum(thermal radiation background)was observed and increased in intensity with V0.However,for V0<2 km/s,only atomic line spectra were detected.There was no aluminum spectral lines for V0<2 km/s,which indicated that it had not been vaporized.The initial intense flash was emission from excited and ionized ambient gases near the impact surface,and had little relationship with shock temperature rise,indicating a new mechanism of impact flash.
