The size-dependent elastic property of rectangular nanobeams （nanowires or nanoplates） induced by the surface elas- ticity effect is investigated by using a developed modified core-shell model. The effect of surface...The size-dependent elastic property of rectangular nanobeams （nanowires or nanoplates） induced by the surface elas- ticity effect is investigated by using a developed modified core-shell model. The effect of surface elasticity on the elastic modulus of nanobeams can be characterized by two surface related parameters, i.e., inhomogeneous degree constant and surface layer thickness. The analytical results show that the elastic modulus of the rectangular nanobeam exhibits a distinct size effect when its characteristic size reduces below 1 O0 nm. It is also found that the theoretical results calculated by a mod- ified core-shell model have more obvious advantages than those by other models （core-shell model and core-surface model） by comparing them with relevant experimental measurements and computational results, especially when the dimensions of nanostructures reduce to a few tens of nanometers.展开更多
A simple uniaxial oedometric system is developed to test the elastic modulus of granular materials. The stress- strain relationship is first measured under conditions of uniaxial compression with additional lateral st...A simple uniaxial oedometric system is developed to test the elastic modulus of granular materials. The stress- strain relationship is first measured under conditions of uniaxial compression with additional lateral stress and strain, then the elastic modulus of the material is determined by the linear fitting method. It is found that the modulus is positively correlated to the grain size and negatively correlated to the container size. Arching and dragging are revealed to be the mechanism of such correlations by using the digital image correlation method and the pressure film technology based on the statistical method.展开更多
In this paper, we proposed a five-zone model to predict the elastic modulus of particulate reinforced metal matrix composite. We simplified the calculation by ignoring structural parameters including particulate shape...In this paper, we proposed a five-zone model to predict the elastic modulus of particulate reinforced metal matrix composite. We simplified the calculation by ignoring structural parameters including particulate shape, arrangement pattern and dimensional variance mode which have no obvious influence on the elastic modulus of a composite, and improved the precision of the method by stressing the interaction of interfaces with pariculates and maxtrix of the composite. The five- zone model can reflect effects of interface modulus on elastic modulus of composite. It overcomes limitations of expressions of rigidity mixed law and flexibility mixed law. The original idea of five zone model is to put forward the particulate/interface interactive zone and matrix/interface interactive zone. By organically integrating the rigidity mixed law and flexibility mixed law, the model can predict the engineering elastic constant of a composite effectively.展开更多
The support layer is an important component of twin-block ballastless track. The modulus of the support layer is an important design parameter and must be carefully solved. We studied the bending stress and deformatio...The support layer is an important component of twin-block ballastless track. The modulus of the support layer is an important design parameter and must be carefully solved. We studied the bending stress and deformation of track slab and support layer due to train load using the beam-plate finite element model on elastic foundation. The results show that support layer type has great impact on both support layer deformation and the stress on subgrade, but has little impact on the bending stress of either track slab or support layer. The continuous support layer type, and articulated support layer type with shear transfer device at their ends, are recommended. In order to keep the stress in the support layer less than that in track slab, the modulus of the continuous, unit, and articulated types of support layer （ in unit twin-block ballastless track）, and the support layer in continuous twin-block ballastless track, should not be larger than 15, 22, 20.5 and 5 GPa, respectively. In addition, the modulus of the unit-type support layer should not be more than 20 GPa, to ensure the step in support layer remains less than 1 mm.展开更多
Micro/nano-thin films are widely used in the fields of micro/nano-electromechanical system(MEMS/NEMS)and flexible electronics,and their mechanical properties have an important impact on the stability and reliability o...Micro/nano-thin films are widely used in the fields of micro/nano-electromechanical system(MEMS/NEMS)and flexible electronics,and their mechanical properties have an important impact on the stability and reliability of components.However,accurate characterization of the mechanical properties of thin films still faces challenges due to the complexity of film-substrate structure,and the characterization efficiency of traditional techniques is insufficient.In this paper,a high-throughput determination method of the elastic modulus of thin films is proposed based on the strain variance method,the feasibility of which is analyzed by the finite element method(FEM),and the specific tensile configuration with array-distributed thin films is designed and optimized.Based on the strain difference between the film-substrate region and the uncoated region,the elastic modulus of multiple films is obtained simultaneously,and the influences of film width,spacing,thickness,and distribution on the measurement of elastic modulus are elucidated.The results show that the change in film width has a more obvious effect on the elastic modulus determination than film spacing and thickness,i.e.,the larger the film width is,the closer the calculation results are to the theoretical value,and the change in calculation results tends to be stabilized when the film width increases to a certain length.Specifically,the simultaneous measurement of the elastic modulus of eight metal films on a polyimide(PI)substrate with a length of 110 mm and a width of 30 mm can be realized,and the testing throughput can be further increased with the extension of the substrate length.This study provides an efficient and low-cost method for measuring the elastic modulus of thin films,which is expected to accelerate the development of new thin film materials.展开更多
The dynamic and static modulus of elasticity （MOE） between bluestained and non-bluestained lumber of Lodgepole pine were tested and analyzed by using three methods of Non-destructive testing （NDT）, Portable Ultras...The dynamic and static modulus of elasticity （MOE） between bluestained and non-bluestained lumber of Lodgepole pine were tested and analyzed by using three methods of Non-destructive testing （NDT）, Portable Ultrasonic Non-destructive Digital Indicating Testing （Pundit）, Metriguard and Fast Fourier Transform （FFT） and the normal bending method. Results showed that the dynamic and static MOE of bluestained wood were higher than those of non-bluestained wood. The significant differences in dynamic MOE and static MOE were found between bulestained and non-bluestained wood, of which, the difference in each of three dynamic MOE （Ep. the ultrasonic wave modulus of elasticity, Ems, the stress wave modulus of elasticity and El, the longitudinal wave modulus of elasticity） between bulestained and non-bluestained wood arrived at the 0.01 significance level, whereas that in the static MOE at the 0.05 significance level. The differences in MOE between bulestained and non-bluestained wood were induced by the variation between sapwood and heartwood and the different densities of bulestained and non-bluestained wood. The correlation between dynamic MOE and static MOE was statistically significant at the 0.01 significance level. Although the dynamic MOE values of Ep, Em, Er were significantly different, there exists a close relationship between them （arriving at the 0.01 correlation level）. Comparative analysis among the three techniques indicated that the accurateness of FFT was higher than that of Pundit and Metriguard. Effect of tree knots on MOE was also investigated. Result showed that the dynamic and static MOE gradually decreased with the increase of knot number, indicating that knot number had significant effect on MOE value.展开更多
Uniaxial Compressive Strength (UCS) and modulus of elasticity (E) are the most important rock parameters required and determined for rock mechanical studies in most civil and mining projects. In this study, two mathem...Uniaxial Compressive Strength (UCS) and modulus of elasticity (E) are the most important rock parameters required and determined for rock mechanical studies in most civil and mining projects. In this study, two mathematical methods, regression analysis and Artificial Neural Networks (ANNs), were used to predict the uniaxial compressive strength and modulus of elasticity. The P-wave velocity, the point load index, the Schmidt hammer rebound number and porosity were used as inputs for both meth-ods. The regression equations show that the relationship between P-wave velocity, point load index, Schmidt hammer rebound number and the porosity input sets with uniaxial compressive strength and modulus of elasticity under conditions of linear rela-tions obtained coefficients of determination of (R2) of 0.64 and 0.56, respectively. ANNs were used to improve the regression re-sults. The generalized regression and feed forward neural networks with two outputs (UCS and E) improved the coefficients of determination to more acceptable levels of 0.86 and 0.92 for UCS and to 0.77 and 0.82 for E. The results show that the proposed ANN methods could be applied as a new acceptable method for the prediction of uniaxial compressive strength and modulus of elasticity of intact rocks.展开更多
The effects of boron and carbon on the structural, elastic, and electronic properties of both Ni solution and NiAl intermetallics are investigated using first-principles calculations. The results agree well with theor...The effects of boron and carbon on the structural, elastic, and electronic properties of both Ni solution and NiAl intermetallics are investigated using first-principles calculations. The results agree well with theoretical and experimental data from previous studies and are analyzed based on the density of states and charge density. It is found that both boron and carbon are inclined to occupy the Ni-rich interstices in NiAl, which gives rise to a cubic interstitial phase. In addition,the interstitial boron and carbon have different effects on the elastic moduli of Ni and NiAl. The calculation results for the G/B and Poisson’s ratios further demonstrate that interstitial boron and carbon can both reduce the brittleness of Ni, thereby increasing its ductility. Meanwhile, boron can also enhance the ductility of the NiAl while carbon hardly has an effect on its brittleness or ductility.展开更多
This paper have performed molecular static calculations with the quantum corrected Sutten Chen type many body potential to study size effects on the elastic modulus of Au nanowires with [100], [110] and [111] crystall...This paper have performed molecular static calculations with the quantum corrected Sutten Chen type many body potential to study size effects on the elastic modulus of Au nanowires with [100], [110] and [111] crystallographic directions, and to explore the preferential growth orientation of Au nanowires. The main focus of this work is the size effects on their surface characteristics. Using the common neighbour analysis, this paper deduces that surface region approximately consists of two layer atoms. Further, it extracts the elastic modulus of surface, and calculate surface energy of nanowire. The results show that for all three directions the Young＇s modulus of nanowire increases as the diameter increases. Similar trend has been observed for the Young＇s modulus of surface. However, the atomic average potential energy of nanowire shows an opposite change. Both the potential and surface energy of [110] nanowire are the lowest among all three orlentational nanowires, which helps to explain why Au nanowires possess a [110] preferred orientation during the experimental growth proceeds.展开更多
The plane-wave pseudopotential method using the generalized gradient approximation within the density functional theory is used to investigate the structure and bulk modulus of WSi2. The quasi-harmonic Debye model, us...The plane-wave pseudopotential method using the generalized gradient approximation within the density functional theory is used to investigate the structure and bulk modulus of WSi2. The quasi-harmonic Debye model, using a set of total energy versus cell volume obtained with the plane-wave pseudopotential method, is applied to the study of the elastic properties and vibrational effects. We have analysed the bulk modulus of WSi2 up to 1600 K. The major trend shows that the WSi2 crystal becomes more compressible when the temperature rises and the increase of compressibility leads to the decrease of Debye temperature. The predicted temperature and pressure effects on the thermal expansion, heat capacity and Debye temperatures are determined from the non-equilibrium Gibbs functions and compared with the data available.展开更多
The electronic, elastic, vibrational, and thermodynamic properties of Sr_（10）（PO_4）_6F_2（Sr-FAP） and Ca_（10）（PO_4）_6F_2（CaFAP） are systematically investigated by the first-principles calculations. The calc...The electronic, elastic, vibrational, and thermodynamic properties of Sr_（10）（PO_4）_6F_2（Sr-FAP） and Ca_（10）（PO_4）_6F_2（CaFAP） are systematically investigated by the first-principles calculations. The calculated electronic band structure indicates that the Sr-FAP and Ca-FAP are insulator materials with the indirect band gap of 5.273 eV and 5.592 eV, respectively. The elastic constants are obtained by the “stress–strain” method, and elastic modulus are further evaluated and discussed. The vibrational properties, including the phonon dispersion curves, the phonon density of states, the Born effective charge, and associated longitudinal optical and transverse optical（LO–TO） splitting of optical modes, as well as the phonon frequencies at zone-center are obtained within the linear-response approach. Substitution of Ca by Sr causes phonon frequencies to shift to lower values as expected due to the mass effect. Additionally, some phonon-related thermodynamic properties, such as Helmholtz free energy F, internal energy E, entropy S, and specific heat C_V of Sr-FAP and Ca-FAP are predicted with the harmonic approximation. The present calculated results of two apatites are consistent with the reported experimental and theoretical results.展开更多
To understand and develop new nanostructure materials with specific mechanical properties, a good knowledge of the elastic strain response is mandatory. Here we investigate the linear elasticity response in the modifi...To understand and develop new nanostructure materials with specific mechanical properties, a good knowledge of the elastic strain response is mandatory. Here we investigate the linear elasticity response in the modified phase-field-crystal（MPFC） model. The results show that two different propagation modes control the elastic interaction length and time, which determine whether the density waves can propagate or not. By quantitatively calculating the strain field, we find that the strain distribution is indeed extremely uniform in case of elasticity. Further, we present a detailed theoretical analysis for the orientation dependence and temperature dependence of shear modulus. The simulation results show that the shear modulus reveals strong anisotropy and the one-mode analysis provides a good guideline for determining elastic shear constants until the system temperature falls below a certain value.展开更多
Understanding the hydrate adhesion is important to tackling hydrate accretion in petro-pipelines.Herein,the relationship between the Tetrahydrofuran(THF)hydrate adhesion strength(AS)and surface stiffness on elastic co...Understanding the hydrate adhesion is important to tackling hydrate accretion in petro-pipelines.Herein,the relationship between the Tetrahydrofuran(THF)hydrate adhesion strength(AS)and surface stiffness on elastic coatings is systemically examined by experimental shear force measurements and theoretical methods.The mechanical factor-elastic modulus of the coatings greatly dictates the hydrate AS,which is explained by the adhesion mechanics theory,beyond the usual factors such as wettability and structural roughness.Moreover,the hydrate AS increases with reducing the thickness of the elastic coatings,resulted from the decrease of the apparent surface elastic modulus.The effect of critical thickness for the elastic materials with variable elastic modulus on the hydrate AS is also revealed.This study provides deep perspectives on the regulation of the hydrate AS by the elastic modulus of elastic materials,which is of significance to design anti-hydrate surfaces for mitigation of hydrate accretion in petro-pipelines.展开更多
Owing to the particularity of a polyester fiber material,the polyester mooring undergoes large axial tensile deformation over long-term use.Large axial tensile deformation significantly impacts the dynamic response of...Owing to the particularity of a polyester fiber material,the polyester mooring undergoes large axial tensile deformation over long-term use.Large axial tensile deformation significantly impacts the dynamic response of the mooring system.In addition,the degrees of large axial tension caused by different elastic moduli are also different,and the force on the mooring line is also different.Therefore,it is of great significance to study the influence of elastic modulus on the dynamic results of the mooring systems under large axial tension.Conventional numerical software fails to consider the axial tension deformation of the mooring.Based on the theory of slender rods,this paper derives the formula for large axial tension using the method of overall coordinates and overall slope coordinates and provides the calculation programs.Considering a polyester mooring system as an example,the calculation program and numerical software are used to calculate and compare the static and dynamic analyses to verify the reliability of the calculation program.To make the force change of the mooring obvious,the elastic moduli of three different orders of magnitude are compared and analyzed,and the dynamic response results after large axial tension are compared.This study concludes that the change in the elastic modulus of the polyester mooring changes the result of the vertex tension by generating an axial tension.The smaller the elastic modulus,the larger the forced oscillation motion amplitude of the top point of the mooring line,the more obvious the axial tension phenomenon,and the smaller the force on the top of the polyester mooring.展开更多
The effectiveness of pilodyn was tested in evaluating wood basic density, outer wood density, heartwood density, and modulus of elasticity （MoE） at 22 four-year-old eucalyptus clones in Guangxi, China. Results indic...The effectiveness of pilodyn was tested in evaluating wood basic density, outer wood density, heartwood density, and modulus of elasticity （MoE） at 22 four-year-old eucalyptus clones in Guangxi, China. Results indicated that the mean value ranged from 9.44 to 15.41 mm for Pilodyn penetration, 0.3514 to 0.4913 g.cm^-3 for wood basic density, and 3.94 to 7.53 Giga Pascal （GPa） for MoE, respectively. There were significant differences （1% level） in pilodyn penetration between different treatments, different directions and among the clones. Generally strongly negative correlations were found between pilodyn penetration and wood properties, and the coefficients ranged from -0,433 to -0,755. Our results, together with other studies, suggest that the use of pilodyn for assessing wood density and MoE was confirmed as a possibility.展开更多
The dimension lumber （45mm×90mm×3700mm） of plantation Chinese fir （Cunninghamia lanceolata （Lamb.） Hook.） was graded to four different classes as SS, No. 1, No.2 and No.3, according to national lumber ...The dimension lumber （45mm×90mm×3700mm） of plantation Chinese fir （Cunninghamia lanceolata （Lamb.） Hook.） was graded to four different classes as SS, No. 1, No.2 and No.3, according to national lumber grades authority （NLGA） for structure light framing and structure joists and planks. The properties of apparent density was determined at 15% moisture content, bending strength and stiffness were tested according to American Society for Testing and Materials （ASTM） D198-99, and dynamic modulus of elasticity （Eusw） was measured by ultrasonic technique, for predicting the flexural properties of different grade lumbers. The results showed that Eosw was larger than the static MOE. The relationship between Eusw and static MOE was significant at 0.01 level, and the determination coefficients （R2） of the four grade lumbers followed the sequence as R^2No.2 （0.616）〉 R^2ss （0.567）〉 R^2No1 （0.366）〉 R^2No.3 （0.137）. The R^2 of Fusw and MOR were lower than that of the Etru and MOR for each grade. The Eusw of all the grade lumbers, except No.3-grade, had significant correlation with the static MOE and MOR, thus the bending strengthof those grade lumbers can be estimated by the E The Etru valuesof four grade lumbers followed a sequence as No.2-grade （10.701 GPa） 〉 SS-grade （10.359 GPa） 〉 No.l-grade （9.840 GPa） 〉 No.3-grade （9.554 GPa）. For the same grade dimension lumber, its Eusw value was larger than static MOE. Mean values of MOR for four grade lumbers follow a sequence as No.2-grade （48.67 MPa） 〉 SS-grade （48.16 MPa） 〉 No.3-grade （46.55 MPa） 〉 No. 1-grade （43.39MPa）.展开更多
Flexible pressure sensors with high sensitivity are desired in the fields of electronic skins,human-machine interfaces,and health monitoring.Employing ionic soft materials with microstructured architectures in the fun...Flexible pressure sensors with high sensitivity are desired in the fields of electronic skins,human-machine interfaces,and health monitoring.Employing ionic soft materials with microstructured architectures in the functional layer is an effective way that can enhance the amplitude of capacitance signal due to generated electron double layer and thus improve the sensitivity of capacitive-type pressure sensors.However,the requirement of specific apparatus and the complex fabrication process to build such microstructures lead to high cost and low productivity.Here,we report a simple strategy that uses open-cell polyurethane foams with high porosity as a continuous three-dimensional network skeleton to load with ionic liquid in a one-step soak process,serving as the ionic layer in iontronic pressure sensors.The high porosity(95.4%) of PU-IL composite foam shows a pretty low Young's modulus of 3.4 kPa and good compressibility.A superhigh maximum sensitivity of 9,280 kPa^(-1) in the pressure regime and a high pressure resolution of 0.125% are observed in this foam-based pressure sensor.The device also exhibits remarkable mechanical stability over 5,000 compression-release or bending-release cycles.Such high porosity of composite structure provides a simple,cost-effective and scalable way to fabricate super sensitive pressure sensor,which has prominent capability in applications of water wave detection,underwater vibration sensing,and mechanical fault monitoring.展开更多
Molecular dynamics simulations are used to investigate the stabilities of C15 Laves phase structures subjected to temperature and point defects. The simulations based on different empirical potentials show that the bu...Molecular dynamics simulations are used to investigate the stabilities of C15 Laves phase structures subjected to temperature and point defects. The simulations based on different empirical potentials show that the bulk perfect C15 Laves phase appears to be stable under a critical temperature in a range from 350 K to 450 K, beyond which it becomes disordered and experiences an abrupt decrement of elastic modulus. In the presence of both vacancy and self-interstitial, the bulk C15 Laves phase becomes unstable at room temperature and prefers to transform into an imperfect body centered cubic（BCC）structure containing free vacancies or vacancy clusters. When a C15 cluster is embedded in BCC iron, the annihilation of interstitials occurs due to the presence of the vacancy, while it exhibits a phase transformation into a（1/2） 111 dislocation loop due to the presence of the self-interstitial.展开更多
Many measures, such as water injection, acid fracturing, thermal recovery, have been taken in the oilfield development. These can easily induce brittle fracture of set cement. Most of all, there are greater potential ...Many measures, such as water injection, acid fracturing, thermal recovery, have been taken in the oilfield development. These can easily induce brittle fracture of set cement. Most of all, there are greater potential for fractures in set cement in slim holes. Therefore, it is necessary to improve the toughness of the cement mantle. Results obtained from experiments show that carbon fiber, with a concentration of 0.12%-0.19% in cement and a length of 700 to 1,400μm, plays an important role in improving cement quality. Addition of carbon fiber can improve the bending strength of set cement by up to 30%. At the same time, the increase in fiber concentration can lower the elastic modulus and increase the Poisson＇s ratio of set cement. Thin-section analysis shows that fiber can effectively prevent the propagation of fractures and enhance the plasticity of the matrix and the ability to prevent fracture.展开更多
The alloying and magnetic disordering effects on site occupation,elastic property,and phase stability of Co_(2)Y Ga(Y=Cr,V,and Ni)shape memory alloys are systematically investigated using the first-principles exact mu...The alloying and magnetic disordering effects on site occupation,elastic property,and phase stability of Co_(2)Y Ga(Y=Cr,V,and Ni)shape memory alloys are systematically investigated using the first-principles exact muffin-tin orbitals method.It is shown that with the increasing magnetic disordering degree y,their tetragonal shear elastic constant C′(i.e.,(C_(11)-C_(12))/2)of the L2_(1) phase decreases whereas the elastic anisotropy A increases,and upon tetragonal distortions the cubic phase gets more and more unstable.Co_(2)Cr Ga and Co_(2)VGa alloys with y≥0.2 thus can show the martensitic transformation(MT)from L2_(1)to D0_(22)as well as Co_(2)Ni Ga.In off-stoichiometric alloys,the site preference is controlled by both the alloying and magnetic effects.At the ferromagnetism state,the excessive Ga atoms always tend to take the Y sublattices,whereas the excessive Co atom favor the Y sites when Y=Cr,and the excessive Y atoms prefer the Co sites when Y=Ni.The Ga-deficient Y=V alloys can also occur the MT at the ferromagnetism state by means of Co or V doping,and the MT temperature TMshould increase with their addition.In the corresponding ferromagnetism Y=Cr alloys,nevertheless,with Co or Cr substituting for Ga,the reentrant MT(RMT)from D0_(22)to L2_(1)is promoted and then TMfor the RMT should decrease.The alloying effect on the MT of these alloys is finally well explained by means of the Jahn-Teller effect at the paramagnetic state.At the ferromagnetism state,it may originate from the competition between the austenite and martensite about their strength of the covalent banding between Co and Ga as well as Y and Ga.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant No.11072104)the Scientific Research Program for Higher Schools of Inner Mongolia (Grant No.NJZY13013)
文摘The size-dependent elastic property of rectangular nanobeams （nanowires or nanoplates） induced by the surface elas- ticity effect is investigated by using a developed modified core-shell model. The effect of surface elasticity on the elastic modulus of nanobeams can be characterized by two surface related parameters, i.e., inhomogeneous degree constant and surface layer thickness. The analytical results show that the elastic modulus of the rectangular nanobeam exhibits a distinct size effect when its characteristic size reduces below 1 O0 nm. It is also found that the theoretical results calculated by a mod- ified core-shell model have more obvious advantages than those by other models （core-shell model and core-surface model） by comparing them with relevant experimental measurements and computational results, especially when the dimensions of nanostructures reduce to a few tens of nanometers.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11372038 and 11402023
文摘A simple uniaxial oedometric system is developed to test the elastic modulus of granular materials. The stress- strain relationship is first measured under conditions of uniaxial compression with additional lateral stress and strain, then the elastic modulus of the material is determined by the linear fitting method. It is found that the modulus is positively correlated to the grain size and negatively correlated to the container size. Arching and dragging are revealed to be the mechanism of such correlations by using the digital image correlation method and the pressure film technology based on the statistical method.
基金Funded by Academician Foundation of Chongqing Project (2002-6285).
文摘In this paper, we proposed a five-zone model to predict the elastic modulus of particulate reinforced metal matrix composite. We simplified the calculation by ignoring structural parameters including particulate shape, arrangement pattern and dimensional variance mode which have no obvious influence on the elastic modulus of a composite, and improved the precision of the method by stressing the interaction of interfaces with pariculates and maxtrix of the composite. The five- zone model can reflect effects of interface modulus on elastic modulus of composite. It overcomes limitations of expressions of rigidity mixed law and flexibility mixed law. The original idea of five zone model is to put forward the particulate/interface interactive zone and matrix/interface interactive zone. By organically integrating the rigidity mixed law and flexibility mixed law, the model can predict the engineering elastic constant of a composite effectively.
基金The National Natural Science Foundation of China(Director Program)(No.50848015)the Innovative Research Team Incubation Financing Projects of Southwest Jiaotong University(No.2007IRT06)
文摘The support layer is an important component of twin-block ballastless track. The modulus of the support layer is an important design parameter and must be carefully solved. We studied the bending stress and deformation of track slab and support layer due to train load using the beam-plate finite element model on elastic foundation. The results show that support layer type has great impact on both support layer deformation and the stress on subgrade, but has little impact on the bending stress of either track slab or support layer. The continuous support layer type, and articulated support layer type with shear transfer device at their ends, are recommended. In order to keep the stress in the support layer less than that in track slab, the modulus of the continuous, unit, and articulated types of support layer （ in unit twin-block ballastless track）, and the support layer in continuous twin-block ballastless track, should not be larger than 15, 22, 20.5 and 5 GPa, respectively. In addition, the modulus of the unit-type support layer should not be more than 20 GPa, to ensure the step in support layer remains less than 1 mm.
文摘Micro/nano-thin films are widely used in the fields of micro/nano-electromechanical system(MEMS/NEMS)and flexible electronics,and their mechanical properties have an important impact on the stability and reliability of components.However,accurate characterization of the mechanical properties of thin films still faces challenges due to the complexity of film-substrate structure,and the characterization efficiency of traditional techniques is insufficient.In this paper,a high-throughput determination method of the elastic modulus of thin films is proposed based on the strain variance method,the feasibility of which is analyzed by the finite element method(FEM),and the specific tensile configuration with array-distributed thin films is designed and optimized.Based on the strain difference between the film-substrate region and the uncoated region,the elastic modulus of multiple films is obtained simultaneously,and the influences of film width,spacing,thickness,and distribution on the measurement of elastic modulus are elucidated.The results show that the change in film width has a more obvious effect on the elastic modulus determination than film spacing and thickness,i.e.,the larger the film width is,the closer the calculation results are to the theoretical value,and the change in calculation results tends to be stabilized when the film width increases to a certain length.Specifically,the simultaneous measurement of the elastic modulus of eight metal films on a polyimide(PI)substrate with a length of 110 mm and a width of 30 mm can be realized,and the testing throughput can be further increased with the extension of the substrate length.This study provides an efficient and low-cost method for measuring the elastic modulus of thin films,which is expected to accelerate the development of new thin film materials.
基金This paper was supported by "Wood-inorganic Res-toration Material" in "Technique Introduction and Innovation of Bio-macromolecule New Material" of Introducing Overseas Advanced Forest Technology Innovation Program of China ("948" Innovation Pro-ject, Number: 2006-4-C03)
文摘The dynamic and static modulus of elasticity （MOE） between bluestained and non-bluestained lumber of Lodgepole pine were tested and analyzed by using three methods of Non-destructive testing （NDT）, Portable Ultrasonic Non-destructive Digital Indicating Testing （Pundit）, Metriguard and Fast Fourier Transform （FFT） and the normal bending method. Results showed that the dynamic and static MOE of bluestained wood were higher than those of non-bluestained wood. The significant differences in dynamic MOE and static MOE were found between bulestained and non-bluestained wood, of which, the difference in each of three dynamic MOE （Ep. the ultrasonic wave modulus of elasticity, Ems, the stress wave modulus of elasticity and El, the longitudinal wave modulus of elasticity） between bulestained and non-bluestained wood arrived at the 0.01 significance level, whereas that in the static MOE at the 0.05 significance level. The differences in MOE between bulestained and non-bluestained wood were induced by the variation between sapwood and heartwood and the different densities of bulestained and non-bluestained wood. The correlation between dynamic MOE and static MOE was statistically significant at the 0.01 significance level. Although the dynamic MOE values of Ep, Em, Er were significantly different, there exists a close relationship between them （arriving at the 0.01 correlation level）. Comparative analysis among the three techniques indicated that the accurateness of FFT was higher than that of Pundit and Metriguard. Effect of tree knots on MOE was also investigated. Result showed that the dynamic and static MOE gradually decreased with the increase of knot number, indicating that knot number had significant effect on MOE value.
文摘Uniaxial Compressive Strength (UCS) and modulus of elasticity (E) are the most important rock parameters required and determined for rock mechanical studies in most civil and mining projects. In this study, two mathematical methods, regression analysis and Artificial Neural Networks (ANNs), were used to predict the uniaxial compressive strength and modulus of elasticity. The P-wave velocity, the point load index, the Schmidt hammer rebound number and porosity were used as inputs for both meth-ods. The regression equations show that the relationship between P-wave velocity, point load index, Schmidt hammer rebound number and the porosity input sets with uniaxial compressive strength and modulus of elasticity under conditions of linear rela-tions obtained coefficients of determination of (R2) of 0.64 and 0.56, respectively. ANNs were used to improve the regression re-sults. The generalized regression and feed forward neural networks with two outputs (UCS and E) improved the coefficients of determination to more acceptable levels of 0.86 and 0.92 for UCS and to 0.77 and 0.82 for E. The results show that the proposed ANN methods could be applied as a new acceptable method for the prediction of uniaxial compressive strength and modulus of elasticity of intact rocks.
基金supported by the National Basic Research Program of China(Grant No.2011CB606402)
文摘The effects of boron and carbon on the structural, elastic, and electronic properties of both Ni solution and NiAl intermetallics are investigated using first-principles calculations. The results agree well with theoretical and experimental data from previous studies and are analyzed based on the density of states and charge density. It is found that both boron and carbon are inclined to occupy the Ni-rich interstices in NiAl, which gives rise to a cubic interstitial phase. In addition,the interstitial boron and carbon have different effects on the elastic moduli of Ni and NiAl. The calculation results for the G/B and Poisson’s ratios further demonstrate that interstitial boron and carbon can both reduce the brittleness of Ni, thereby increasing its ductility. Meanwhile, boron can also enhance the ductility of the NiAl while carbon hardly has an effect on its brittleness or ductility.
基金support by the National 973 Project of China (Grant No 2006CB605102)the National Natural Science Foundation of China (Grant No 10702056)Program for New Century Excellent Talents in Fujian Province University,China (NCETFJ)
文摘This paper have performed molecular static calculations with the quantum corrected Sutten Chen type many body potential to study size effects on the elastic modulus of Au nanowires with [100], [110] and [111] crystallographic directions, and to explore the preferential growth orientation of Au nanowires. The main focus of this work is the size effects on their surface characteristics. Using the common neighbour analysis, this paper deduces that surface region approximately consists of two layer atoms. Further, it extracts the elastic modulus of surface, and calculate surface energy of nanowire. The results show that for all three directions the Young＇s modulus of nanowire increases as the diameter increases. Similar trend has been observed for the Young＇s modulus of surface. However, the atomic average potential energy of nanowire shows an opposite change. Both the potential and surface energy of [110] nanowire are the lowest among all three orlentational nanowires, which helps to explain why Au nanowires possess a [110] preferred orientation during the experimental growth proceeds.
基金supported by the Basic Research Program of Education Bureau of Henan Province of China (Grant No 2008A140006)the National Natural Science Foundation of China (Grant No 10774039)
文摘The plane-wave pseudopotential method using the generalized gradient approximation within the density functional theory is used to investigate the structure and bulk modulus of WSi2. The quasi-harmonic Debye model, using a set of total energy versus cell volume obtained with the plane-wave pseudopotential method, is applied to the study of the elastic properties and vibrational effects. We have analysed the bulk modulus of WSi2 up to 1600 K. The major trend shows that the WSi2 crystal becomes more compressible when the temperature rises and the increase of compressibility leads to the decrease of Debye temperature. The predicted temperature and pressure effects on the thermal expansion, heat capacity and Debye temperatures are determined from the non-equilibrium Gibbs functions and compared with the data available.
基金supported by the National High Technology Research and Development Program of China(Grant No.2015AA034202)the National Natural Science Foundation of China(Grant No.11305147)
文摘The electronic, elastic, vibrational, and thermodynamic properties of Sr_（10）（PO_4）_6F_2（Sr-FAP） and Ca_（10）（PO_4）_6F_2（CaFAP） are systematically investigated by the first-principles calculations. The calculated electronic band structure indicates that the Sr-FAP and Ca-FAP are insulator materials with the indirect band gap of 5.273 eV and 5.592 eV, respectively. The elastic constants are obtained by the “stress–strain” method, and elastic modulus are further evaluated and discussed. The vibrational properties, including the phonon dispersion curves, the phonon density of states, the Born effective charge, and associated longitudinal optical and transverse optical（LO–TO） splitting of optical modes, as well as the phonon frequencies at zone-center are obtained within the linear-response approach. Substitution of Ca by Sr causes phonon frequencies to shift to lower values as expected due to the mass effect. Additionally, some phonon-related thermodynamic properties, such as Helmholtz free energy F, internal energy E, entropy S, and specific heat C_V of Sr-FAP and Ca-FAP are predicted with the harmonic approximation. The present calculated results of two apatites are consistent with the reported experimental and theoretical results.
基金Project supported by the National Natural Science foundation of China(Grant Nos.51571165 and 51371151)Special Program for Applied Research on Super Computation of the NSFC-Guangdong Joint Fund(the second phase),Chinathe Fundamental Research Funds for the Central Universities,China(Grant No.3102015BJ(II)ZS001)
文摘To understand and develop new nanostructure materials with specific mechanical properties, a good knowledge of the elastic strain response is mandatory. Here we investigate the linear elasticity response in the modified phase-field-crystal（MPFC） model. The results show that two different propagation modes control the elastic interaction length and time, which determine whether the density waves can propagate or not. By quantitatively calculating the strain field, we find that the strain distribution is indeed extremely uniform in case of elasticity. Further, we present a detailed theoretical analysis for the orientation dependence and temperature dependence of shear modulus. The simulation results show that the shear modulus reveals strong anisotropy and the one-mode analysis provides a good guideline for determining elastic shear constants until the system temperature falls below a certain value.
基金This work is financially supported by the Key Laboratory of Icing and Anti/De-icing of CARDC(Grant No.IADL20210402)the National Natural Science Foundation of China(Grant Nos.12002350,12172314,11772278 and 11904300)+1 种基金the Jiangxi Provincial Outstanding Young Talents Program(Grant No.20192BCBL23029)the Fundamental Research Funds for the Central Universities(Xiamen University:Grant No.20720210025).
文摘Understanding the hydrate adhesion is important to tackling hydrate accretion in petro-pipelines.Herein,the relationship between the Tetrahydrofuran(THF)hydrate adhesion strength(AS)and surface stiffness on elastic coatings is systemically examined by experimental shear force measurements and theoretical methods.The mechanical factor-elastic modulus of the coatings greatly dictates the hydrate AS,which is explained by the adhesion mechanics theory,beyond the usual factors such as wettability and structural roughness.Moreover,the hydrate AS increases with reducing the thickness of the elastic coatings,resulted from the decrease of the apparent surface elastic modulus.The effect of critical thickness for the elastic materials with variable elastic modulus on the hydrate AS is also revealed.This study provides deep perspectives on the regulation of the hydrate AS by the elastic modulus of elastic materials,which is of significance to design anti-hydrate surfaces for mitigation of hydrate accretion in petro-pipelines.
基金Supported by the Specialized Research Project for LS17-2 Semi-submersible Production Platform(LSZX-2020-HN-05-0405)the Engineering Development Program of Deepwater Semisubmersible Production Storage and Unloading Platform of China(SSBQ-2020-HN-02-04)。
文摘Owing to the particularity of a polyester fiber material,the polyester mooring undergoes large axial tensile deformation over long-term use.Large axial tensile deformation significantly impacts the dynamic response of the mooring system.In addition,the degrees of large axial tension caused by different elastic moduli are also different,and the force on the mooring line is also different.Therefore,it is of great significance to study the influence of elastic modulus on the dynamic results of the mooring systems under large axial tension.Conventional numerical software fails to consider the axial tension deformation of the mooring.Based on the theory of slender rods,this paper derives the formula for large axial tension using the method of overall coordinates and overall slope coordinates and provides the calculation programs.Considering a polyester mooring system as an example,the calculation program and numerical software are used to calculate and compare the static and dynamic analyses to verify the reliability of the calculation program.To make the force change of the mooring obvious,the elastic moduli of three different orders of magnitude are compared and analyzed,and the dynamic response results after large axial tension are compared.This study concludes that the change in the elastic modulus of the polyester mooring changes the result of the vertex tension by generating an axial tension.The smaller the elastic modulus,the larger the forced oscillation motion amplitude of the top point of the mooring line,the more obvious the axial tension phenomenon,and the smaller the force on the top of the polyester mooring.
基金supported by the National Eleventh Five-Year Science and Technology (2006BAD01A15-4 and 2006bad24b0203)
文摘The effectiveness of pilodyn was tested in evaluating wood basic density, outer wood density, heartwood density, and modulus of elasticity （MoE） at 22 four-year-old eucalyptus clones in Guangxi, China. Results indicated that the mean value ranged from 9.44 to 15.41 mm for Pilodyn penetration, 0.3514 to 0.4913 g.cm^-3 for wood basic density, and 3.94 to 7.53 Giga Pascal （GPa） for MoE, respectively. There were significant differences （1% level） in pilodyn penetration between different treatments, different directions and among the clones. Generally strongly negative correlations were found between pilodyn penetration and wood properties, and the coefficients ranged from -0,433 to -0,755. Our results, together with other studies, suggest that the use of pilodyn for assessing wood density and MoE was confirmed as a possibility.
基金Standard system on forestry engineering of Ministry ofScience and Technology ( 2004DEA70900-1).
文摘The dimension lumber （45mm×90mm×3700mm） of plantation Chinese fir （Cunninghamia lanceolata （Lamb.） Hook.） was graded to four different classes as SS, No. 1, No.2 and No.3, according to national lumber grades authority （NLGA） for structure light framing and structure joists and planks. The properties of apparent density was determined at 15% moisture content, bending strength and stiffness were tested according to American Society for Testing and Materials （ASTM） D198-99, and dynamic modulus of elasticity （Eusw） was measured by ultrasonic technique, for predicting the flexural properties of different grade lumbers. The results showed that Eosw was larger than the static MOE. The relationship between Eusw and static MOE was significant at 0.01 level, and the determination coefficients （R2） of the four grade lumbers followed the sequence as R^2No.2 （0.616）〉 R^2ss （0.567）〉 R^2No1 （0.366）〉 R^2No.3 （0.137）. The R^2 of Fusw and MOR were lower than that of the Etru and MOR for each grade. The Eusw of all the grade lumbers, except No.3-grade, had significant correlation with the static MOE and MOR, thus the bending strengthof those grade lumbers can be estimated by the E The Etru valuesof four grade lumbers followed a sequence as No.2-grade （10.701 GPa） 〉 SS-grade （10.359 GPa） 〉 No.l-grade （9.840 GPa） 〉 No.3-grade （9.554 GPa）. For the same grade dimension lumber, its Eusw value was larger than static MOE. Mean values of MOR for four grade lumbers follow a sequence as No.2-grade （48.67 MPa） 〉 SS-grade （48.16 MPa） 〉 No.3-grade （46.55 MPa） 〉 No. 1-grade （43.39MPa）.
基金This work was financially supported by the funds of the National Natural Science Foundation of China(No.51903118 and U1613204)the Science Technology the Shenzhen Sci-Tech Fund(No.KYTDPT20181011104007)+2 种基金M.G.also thanks the support of“College Student’s Innovation and Entrepreneurship Program”(No.2018X33).Guangdong Provincial Key Laboratory Program(2021B1212040001)from the Department of Science and Technology of Guangdong Provincethe“Guangdong Innovative and Entrepreneurial Research Team Program”under contract no.2016ZT06G587the“Science Technology and Innovation Committee of Shenzhen Municipality”(Grant No.JCYJ20170817111714314).
文摘Flexible pressure sensors with high sensitivity are desired in the fields of electronic skins,human-machine interfaces,and health monitoring.Employing ionic soft materials with microstructured architectures in the functional layer is an effective way that can enhance the amplitude of capacitance signal due to generated electron double layer and thus improve the sensitivity of capacitive-type pressure sensors.However,the requirement of specific apparatus and the complex fabrication process to build such microstructures lead to high cost and low productivity.Here,we report a simple strategy that uses open-cell polyurethane foams with high porosity as a continuous three-dimensional network skeleton to load with ionic liquid in a one-step soak process,serving as the ionic layer in iontronic pressure sensors.The high porosity(95.4%) of PU-IL composite foam shows a pretty low Young's modulus of 3.4 kPa and good compressibility.A superhigh maximum sensitivity of 9,280 kPa^(-1) in the pressure regime and a high pressure resolution of 0.125% are observed in this foam-based pressure sensor.The device also exhibits remarkable mechanical stability over 5,000 compression-release or bending-release cycles.Such high porosity of composite structure provides a simple,cost-effective and scalable way to fabricate super sensitive pressure sensor,which has prominent capability in applications of water wave detection,underwater vibration sensing,and mechanical fault monitoring.
基金supported by the National Natural Science Foundation of China(Grant Nos.11675230 and 11375242)Canada’s Natural Sciences and Engineering Research Council NSERC Discovery GrantCanada Foundation for Innovation CFI
文摘Molecular dynamics simulations are used to investigate the stabilities of C15 Laves phase structures subjected to temperature and point defects. The simulations based on different empirical potentials show that the bulk perfect C15 Laves phase appears to be stable under a critical temperature in a range from 350 K to 450 K, beyond which it becomes disordered and experiences an abrupt decrement of elastic modulus. In the presence of both vacancy and self-interstitial, the bulk C15 Laves phase becomes unstable at room temperature and prefers to transform into an imperfect body centered cubic（BCC）structure containing free vacancies or vacancy clusters. When a C15 cluster is embedded in BCC iron, the annihilation of interstitials occurs due to the presence of the vacancy, while it exhibits a phase transformation into a（1/2） 111 dislocation loop due to the presence of the self-interstitial.
文摘Many measures, such as water injection, acid fracturing, thermal recovery, have been taken in the oilfield development. These can easily induce brittle fracture of set cement. Most of all, there are greater potential for fractures in set cement in slim holes. Therefore, it is necessary to improve the toughness of the cement mantle. Results obtained from experiments show that carbon fiber, with a concentration of 0.12%-0.19% in cement and a length of 700 to 1,400μm, plays an important role in improving cement quality. Addition of carbon fiber can improve the bending strength of set cement by up to 30%. At the same time, the increase in fiber concentration can lower the elastic modulus and increase the Poisson＇s ratio of set cement. Thin-section analysis shows that fiber can effectively prevent the propagation of fractures and enhance the plasticity of the matrix and the ability to prevent fracture.
基金supported by the National Natural Science Foundation of China(Grant Nos.12174269,11674233and 51301176)the China Postdoctoral Science Foundation(Grant Nos.2013M530133 and 2014T70264)the Natural Science Foundation of Liaoning Province,China(Grant Nos.2019-MS-287 and L201602672)。
文摘The alloying and magnetic disordering effects on site occupation,elastic property,and phase stability of Co_(2)Y Ga(Y=Cr,V,and Ni)shape memory alloys are systematically investigated using the first-principles exact muffin-tin orbitals method.It is shown that with the increasing magnetic disordering degree y,their tetragonal shear elastic constant C′(i.e.,(C_(11)-C_(12))/2)of the L2_(1) phase decreases whereas the elastic anisotropy A increases,and upon tetragonal distortions the cubic phase gets more and more unstable.Co_(2)Cr Ga and Co_(2)VGa alloys with y≥0.2 thus can show the martensitic transformation(MT)from L2_(1)to D0_(22)as well as Co_(2)Ni Ga.In off-stoichiometric alloys,the site preference is controlled by both the alloying and magnetic effects.At the ferromagnetism state,the excessive Ga atoms always tend to take the Y sublattices,whereas the excessive Co atom favor the Y sites when Y=Cr,and the excessive Y atoms prefer the Co sites when Y=Ni.The Ga-deficient Y=V alloys can also occur the MT at the ferromagnetism state by means of Co or V doping,and the MT temperature TMshould increase with their addition.In the corresponding ferromagnetism Y=Cr alloys,nevertheless,with Co or Cr substituting for Ga,the reentrant MT(RMT)from D0_(22)to L2_(1)is promoted and then TMfor the RMT should decrease.The alloying effect on the MT of these alloys is finally well explained by means of the Jahn-Teller effect at the paramagnetic state.At the ferromagnetism state,it may originate from the competition between the austenite and martensite about their strength of the covalent banding between Co and Ga as well as Y and Ga.
